AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity
067d781731
kernel_optimize_test/include/linux/mmc/card.h

130 lines
3.9 KiB
C
Raw Normal View History

Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
/*
* linux/include/linux/mmc/card.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Card driver specific definitions.
*/
#ifndef LINUX_MMC_CARD_H
#define LINUX_MMC_CARD_H
#include <linux/mmc/mmc.h>
struct mmc_cid {
unsigned int manfid;
char prod_name[8];
unsigned int serial;
unsigned short oemid;
unsigned short year;
unsigned char hwrev;
unsigned char fwrev;
unsigned char month;
};
struct mmc_csd {
unsigned char mmca_vsn;
unsigned short cmdclass;
unsigned short tacc_clks;
unsigned int tacc_ns;
[MMC] extend data timeout for writes The CSD contains a "read2write factor" which determines the multiplier to be applied to the read timeout to obtain the write timeout. We were ignoring this parameter, resulting in the possibility for writes being timed out too early. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-03 00:24:59 +08:00
unsigned int r2w_factor;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
unsigned int max_dtr;
unsigned int read_blkbits;
[MMC] Improve MMC card block size selection Select a block size for IO based on the read and write block size combinations, and whether the card supports partial block reads and/or partial block writes. If we are able to satisfy block reads but not block writes, mark the device read only. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-04 06:38:44 +08:00
unsigned int write_blkbits;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
unsigned int capacity;
[MMC] Improve MMC card block size selection Select a block size for IO based on the read and write block size combinations, and whether the card supports partial block reads and/or partial block writes. If we are able to satisfy block reads but not block writes, mark the device read only. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-04 06:38:44 +08:00
unsigned int read_partial:1,
read_misalign:1,
[MMC] Fix missing ',' Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-04 20:40:39 +08:00
write_partial:1,
[MMC] Improve MMC card block size selection Select a block size for IO based on the read and write block size combinations, and whether the card supports partial block reads and/or partial block writes. If we are able to satisfy block reads but not block writes, mark the device read only. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-04 06:38:44 +08:00
write_misalign:1;
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
};
[PATCH] mmc: Add support for mmc v4 high speed mode This adds support for the high-speed modes defined by mmc v4 (assuming the host controller is up to it). On a TI sdhci controller, it improves read speed from 1.3MBps to 2.3MBps. The TI controller can only go up to 24MHz, but everything helps. Another person has taken this basic patch and used it on a Nokia 770 to get a bigger boost because that controller can run at 48MHZ. Signed-off-by: Philip Langdale <philipl@overt.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2006-10-21 18:35:02 +08:00
struct mmc_ext_csd {
unsigned int hs_max_dtr;
};
[PATCH] sd: SCR register Read the SD specific SCR register from the card. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 06:18:53 +08:00
struct sd_scr {
unsigned char sda_vsn;
unsigned char bus_widths;
#define SD_SCR_BUS_WIDTH_1 (1<<0)
#define SD_SCR_BUS_WIDTH_4 (1<<2)
};
mmc: Support for high speed SD cards Modern SD cards support a clock speed of 50 MHz. Make sure we test for this capability and do the song and dance required to activate it. Activating high speed support actually modifies the TRAN_SPEED field of the CSD. But as the spec says that the cards must report 50 MHz, we might as well skip re-reading the CSD. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2006-11-09 06:03:10 +08:00
struct sd_switch_caps {
unsigned int hs_max_dtr;
};
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
struct mmc_host;
/*
* MMC device
*/
struct mmc_card {
struct list_head node; /* node in hosts devices list */
struct mmc_host *host; /* the host this device belongs to */
struct device dev; /* the device */
unsigned int rca; /* relative card address of device */
unsigned int state; /* (our) card state */
#define MMC_STATE_PRESENT (1<<0) /* present in sysfs */
#define MMC_STATE_DEAD (1<<1) /* device no longer in stack */
#define MMC_STATE_BAD (1<<2) /* unrecognised device */
[PATCH] sd: initialize SD cards Support for the Secure Digital protocol in the MMC layer. A summary of the legal issues surrounding SD cards, as understood by yours truly: Members of the Secure Digital Association, hereafter SDA, are required to sign a NDA[1] before given access to any specifications. It has been speculated that including an SD implementation would forbid these members to redistribute Linux. This is the basic problem with SD support so it is unclear if it even is a problem since it has no effect on those of us that aren't members. The SDA doesn't seem to enforce these rules though since the patches included here are based on documentation made public by some of the members. The most complete specs[2] are actually released by Sandisk, one of the founding companies of the SDA. Because of this the NDA is considered a non-issue by most involved in the discussions concerning these patches. It might be that the SDA is only interested in protecting the so called "secure" bits of SD, which so far hasn't been found in any public spec. (The card is split into two sections, one "normal" and one "secure" which has an access scheme similar to TPM:s). (As a side note, Microsoft is working to make things easier for us since they want to be able to include the source code for a SD driver in one of their development kits. HP is making sure that the new NDA will allow a Linux implementation. So far only the SDIO specs have been opened up[3]. More will hopefully follow.) [1] http://www.sdcard.org/membership/images/ippolicy.pdf [2] http://www.sandisk.com/pdf/oem/ProdManualSDCardv1.9.pdf [3] http://www.sdcard.org/sdio/Simplified%20SDIO%20Card%20Specification.pdf This patch contains the central parts of the SD support. If no MMC cards are found on a bus then the MMC layer proceeds looking for SD cards. Helper functions are extended to handle the special needs of SD cards. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 06:18:50 +08:00
#define MMC_STATE_SDCARD (1<<3) /* is an SD card */
[PATCH] sd: read-only switch Support for the read-only switch on SD cards which must be enforced by the host. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 06:18:52 +08:00
#define MMC_STATE_READONLY (1<<4) /* card is read-only */
mmc: Support for high speed SD cards Modern SD cards support a clock speed of 50 MHz. Make sure we test for this capability and do the song and dance required to activate it. Activating high speed support actually modifies the TRAN_SPEED field of the CSD. But as the spec says that the cards must report 50 MHz, we might as well skip re-reading the CSD. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2006-11-09 06:03:10 +08:00
#define MMC_STATE_HIGHSPEED (1<<5) /* card is in high speed mode */
mmc: Add support for SDHC cards Thanks to the generous donation of an SDHC card by John Gilmore, and the surprisingly enlightened decision by the SD Card Association to publish useful specs, I've been able to bash out support for SDHC. The changes are not too profound: i) Add a card flag indicating the card uses block level addressing and check it in the block driver. As we never took advantage of byte-level addressing, this simply involves skipping the block -> byte translation when sending commands. ii) The layout of the CSD is changed - a set of fields are discarded to make space for a larger C_SIZE. We did not reference any of the discarded fields except those related to the C_SIZE. iii) Read and write timeouts are fixed values and not calculated from CSD values. iv) Before invoking SEND_APP_OP_COND, we must invoke the new SEND_IF_COND to inform the card we support SDHC. Signed-off-by: Philipl Langdale <philipl@overt.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-01-04 22:57:32 +08:00
#define MMC_STATE_BLOCKADDR (1<<6) /* card uses block-addressing */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
u32 raw_cid[4]; /* raw card CID */
u32 raw_csd[4]; /* raw card CSD */
[PATCH] sd: SCR register Read the SD specific SCR register from the card. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 06:18:53 +08:00
u32 raw_scr[2]; /* raw card SCR */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
struct mmc_cid cid; /* card identification */
struct mmc_csd csd; /* card specific */
[PATCH] mmc: Add support for mmc v4 high speed mode This adds support for the high-speed modes defined by mmc v4 (assuming the host controller is up to it). On a TI sdhci controller, it improves read speed from 1.3MBps to 2.3MBps. The TI controller can only go up to 24MHz, but everything helps. Another person has taken this basic patch and used it on a Nokia 770 to get a bigger boost because that controller can run at 48MHZ. Signed-off-by: Philip Langdale <philipl@overt.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2006-10-21 18:35:02 +08:00
struct mmc_ext_csd ext_csd; /* mmc v4 extended card specific */
[PATCH] sd: SCR register Read the SD specific SCR register from the card. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 06:18:53 +08:00
struct sd_scr scr; /* extra SD information */
mmc: Support for high speed SD cards Modern SD cards support a clock speed of 50 MHz. Make sure we test for this capability and do the song and dance required to activate it. Activating high speed support actually modifies the TRAN_SPEED field of the CSD. But as the spec says that the cards must report 50 MHz, we might as well skip re-reading the CSD. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2006-11-09 06:03:10 +08:00
struct sd_switch_caps sw_caps; /* switch (CMD6) caps */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
};
#define mmc_card_present(c) ((c)->state & MMC_STATE_PRESENT)
#define mmc_card_dead(c) ((c)->state & MMC_STATE_DEAD)
#define mmc_card_bad(c) ((c)->state & MMC_STATE_BAD)
[PATCH] sd: initialize SD cards Support for the Secure Digital protocol in the MMC layer. A summary of the legal issues surrounding SD cards, as understood by yours truly: Members of the Secure Digital Association, hereafter SDA, are required to sign a NDA[1] before given access to any specifications. It has been speculated that including an SD implementation would forbid these members to redistribute Linux. This is the basic problem with SD support so it is unclear if it even is a problem since it has no effect on those of us that aren't members. The SDA doesn't seem to enforce these rules though since the patches included here are based on documentation made public by some of the members. The most complete specs[2] are actually released by Sandisk, one of the founding companies of the SDA. Because of this the NDA is considered a non-issue by most involved in the discussions concerning these patches. It might be that the SDA is only interested in protecting the so called "secure" bits of SD, which so far hasn't been found in any public spec. (The card is split into two sections, one "normal" and one "secure" which has an access scheme similar to TPM:s). (As a side note, Microsoft is working to make things easier for us since they want to be able to include the source code for a SD driver in one of their development kits. HP is making sure that the new NDA will allow a Linux implementation. So far only the SDIO specs have been opened up[3]. More will hopefully follow.) [1] http://www.sdcard.org/membership/images/ippolicy.pdf [2] http://www.sandisk.com/pdf/oem/ProdManualSDCardv1.9.pdf [3] http://www.sdcard.org/sdio/Simplified%20SDIO%20Card%20Specification.pdf This patch contains the central parts of the SD support. If no MMC cards are found on a bus then the MMC layer proceeds looking for SD cards. Helper functions are extended to handle the special needs of SD cards. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 06:18:50 +08:00
#define mmc_card_sd(c) ((c)->state & MMC_STATE_SDCARD)
[PATCH] sd: read-only switch Support for the read-only switch on SD cards which must be enforced by the host. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 06:18:52 +08:00
#define mmc_card_readonly(c) ((c)->state & MMC_STATE_READONLY)
[PATCH] mmc: Add support for mmc v4 high speed mode This adds support for the high-speed modes defined by mmc v4 (assuming the host controller is up to it). On a TI sdhci controller, it improves read speed from 1.3MBps to 2.3MBps. The TI controller can only go up to 24MHz, but everything helps. Another person has taken this basic patch and used it on a Nokia 770 to get a bigger boost because that controller can run at 48MHZ. Signed-off-by: Philip Langdale <philipl@overt.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2006-10-21 18:35:02 +08:00
#define mmc_card_highspeed(c) ((c)->state & MMC_STATE_HIGHSPEED)
mmc: Add support for SDHC cards Thanks to the generous donation of an SDHC card by John Gilmore, and the surprisingly enlightened decision by the SD Card Association to publish useful specs, I've been able to bash out support for SDHC. The changes are not too profound: i) Add a card flag indicating the card uses block level addressing and check it in the block driver. As we never took advantage of byte-level addressing, this simply involves skipping the block -> byte translation when sending commands. ii) The layout of the CSD is changed - a set of fields are discarded to make space for a larger C_SIZE. We did not reference any of the discarded fields except those related to the C_SIZE. iii) Read and write timeouts are fixed values and not calculated from CSD values. iv) Before invoking SEND_APP_OP_COND, we must invoke the new SEND_IF_COND to inform the card we support SDHC. Signed-off-by: Philipl Langdale <philipl@overt.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-01-04 22:57:32 +08:00
#define mmc_card_blockaddr(c) ((c)->state & MMC_STATE_BLOCKADDR)
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
#define mmc_card_set_present(c) ((c)->state |= MMC_STATE_PRESENT)
#define mmc_card_set_dead(c) ((c)->state |= MMC_STATE_DEAD)
#define mmc_card_set_bad(c) ((c)->state |= MMC_STATE_BAD)
[PATCH] sd: initialize SD cards Support for the Secure Digital protocol in the MMC layer. A summary of the legal issues surrounding SD cards, as understood by yours truly: Members of the Secure Digital Association, hereafter SDA, are required to sign a NDA[1] before given access to any specifications. It has been speculated that including an SD implementation would forbid these members to redistribute Linux. This is the basic problem with SD support so it is unclear if it even is a problem since it has no effect on those of us that aren't members. The SDA doesn't seem to enforce these rules though since the patches included here are based on documentation made public by some of the members. The most complete specs[2] are actually released by Sandisk, one of the founding companies of the SDA. Because of this the NDA is considered a non-issue by most involved in the discussions concerning these patches. It might be that the SDA is only interested in protecting the so called "secure" bits of SD, which so far hasn't been found in any public spec. (The card is split into two sections, one "normal" and one "secure" which has an access scheme similar to TPM:s). (As a side note, Microsoft is working to make things easier for us since they want to be able to include the source code for a SD driver in one of their development kits. HP is making sure that the new NDA will allow a Linux implementation. So far only the SDIO specs have been opened up[3]. More will hopefully follow.) [1] http://www.sdcard.org/membership/images/ippolicy.pdf [2] http://www.sandisk.com/pdf/oem/ProdManualSDCardv1.9.pdf [3] http://www.sdcard.org/sdio/Simplified%20SDIO%20Card%20Specification.pdf This patch contains the central parts of the SD support. If no MMC cards are found on a bus then the MMC layer proceeds looking for SD cards. Helper functions are extended to handle the special needs of SD cards. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 06:18:50 +08:00
#define mmc_card_set_sd(c) ((c)->state |= MMC_STATE_SDCARD)
[PATCH] sd: read-only switch Support for the read-only switch on SD cards which must be enforced by the host. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-07 06:18:52 +08:00
#define mmc_card_set_readonly(c) ((c)->state |= MMC_STATE_READONLY)
[PATCH] mmc: Add support for mmc v4 high speed mode This adds support for the high-speed modes defined by mmc v4 (assuming the host controller is up to it). On a TI sdhci controller, it improves read speed from 1.3MBps to 2.3MBps. The TI controller can only go up to 24MHz, but everything helps. Another person has taken this basic patch and used it on a Nokia 770 to get a bigger boost because that controller can run at 48MHZ. Signed-off-by: Philip Langdale <philipl@overt.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2006-10-21 18:35:02 +08:00
#define mmc_card_set_highspeed(c) ((c)->state |= MMC_STATE_HIGHSPEED)
mmc: Add support for SDHC cards Thanks to the generous donation of an SDHC card by John Gilmore, and the surprisingly enlightened decision by the SD Card Association to publish useful specs, I've been able to bash out support for SDHC. The changes are not too profound: i) Add a card flag indicating the card uses block level addressing and check it in the block driver. As we never took advantage of byte-level addressing, this simply involves skipping the block -> byte translation when sending commands. ii) The layout of the CSD is changed - a set of fields are discarded to make space for a larger C_SIZE. We did not reference any of the discarded fields except those related to the C_SIZE. iii) Read and write timeouts are fixed values and not calculated from CSD values. iv) Before invoking SEND_APP_OP_COND, we must invoke the new SEND_IF_COND to inform the card we support SDHC. Signed-off-by: Philipl Langdale <philipl@overt.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-01-04 22:57:32 +08:00
#define mmc_card_set_blockaddr(c) ((c)->state |= MMC_STATE_BLOCKADDR)
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
#define mmc_card_name(c) ((c)->cid.prod_name)
#define mmc_card_id(c) ((c)->dev.bus_id)
#define mmc_list_to_card(l) container_of(l, struct mmc_card, node)
#define mmc_get_drvdata(c) dev_get_drvdata(&(c)->dev)
#define mmc_set_drvdata(c,d) dev_set_drvdata(&(c)->dev, d)
/*
* MMC device driver (e.g., Flash card, I/O card...)
*/
struct mmc_driver {
struct device_driver drv;
int (*probe)(struct mmc_card *);
void (*remove)(struct mmc_card *);
int (*suspend)(struct mmc_card *, pm_message_t);
int (*resume)(struct mmc_card *);
};
extern int mmc_register_driver(struct mmc_driver *);
extern void mmc_unregister_driver(struct mmc_driver *);
static inline int mmc_card_claim_host(struct mmc_card *card)
{
return __mmc_claim_host(card->host, card);
}
#define mmc_card_release_host(c) mmc_release_host((c)->host)
#endif
Copy Permalink