AcoSail/kernel_optimize_test
8
0
Fork 0
forked from luck/tmp_suning_uos_patched
Code Pull Requests Activity
0d580fbd2d
kernel_optimize_test/net/sched/sch_mqprio.c

643 lines
17 KiB
C
Raw Normal View History

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-04 16:11:33 +08:00
// SPDX-License-Identifier: GPL-2.0-only
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
/*
* net/sched/sch_mqprio.c
*
* Copyright (c) 2010 John Fastabend <john.r.fastabend@intel.com>
*/
#include <linux/types.h>
#include <linux/slab.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/errno.h>
#include <linux/skbuff.h>
net: Fix files explicitly needing to include module.h With calls to modular infrastructure, these files really needs the full module.h header. Call it out so some of the cleanups of implicit and unrequired includes elsewhere can be cleaned up. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-05-27 21:12:25 +08:00
#include <linux/module.h>
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
#include <net/netlink.h>
#include <net/pkt_sched.h>
#include <net/sch_generic.h>
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
#include <net/pkt_cls.h>
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
struct mqprio_sched {
struct Qdisc **qdiscs;
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
u16 mode;
u16 shaper;
mqprio: Change handling of hw u8 to allow for multiple hardware offload modes This patch is meant to allow for support of multiple hardware offload type for a single device. There is currently no bounds checking for the hw member of the mqprio_qopt structure. This results in us being able to pass values from 1 to 255 with all being treated the same. On retreiving the value it is returned as 1 for anything 1 or greater being set. With this change we are currently adding limited bounds checking by defining an enum and using those values to limit the reported hardware offloads. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16 01:39:18 +08:00
int hw_offload;
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
u32 flags;
u64 min_rate[TC_QOPT_MAX_QUEUE];
u64 max_rate[TC_QOPT_MAX_QUEUE];
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
};
static void mqprio_destroy(struct Qdisc *sch)
{
struct net_device *dev = qdisc_dev(sch);
struct mqprio_sched *priv = qdisc_priv(sch);
unsigned int ntx;
sch_mqprio: Always set num_tc to 0 in mqprio_destroy() All the cleanup code in mqprio_destroy() is currently conditional on priv->qdiscs being non-null, but that condition should only apply to the per-queue qdisc cleanup. We should always set the number of traffic classes back to 0 here. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
2011-02-15 03:02:23 +08:00
if (priv->qdiscs) {
for (ntx = 0;
ntx < dev->num_tx_queues && priv->qdiscs[ntx];
ntx++)
net: sched: rename qdisc_destroy() to qdisc_put() Current implementation of qdisc_destroy() decrements Qdisc reference counter and only actually destroy Qdisc if reference counter value reached zero. Rename qdisc_destroy() to qdisc_put() in order for it to better describe the way in which this function currently implemented and used. Extract code that deallocates Qdisc into new private qdisc_destroy() function. It is intended to be shared between regular qdisc_put() and its unlocked version that is introduced in next patch in this series. Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-25 00:22:50 +08:00
qdisc_put(priv->qdiscs[ntx]);
sch_mqprio: Always set num_tc to 0 in mqprio_destroy() All the cleanup code in mqprio_destroy() is currently conditional on priv->qdiscs being non-null, but that condition should only apply to the per-queue qdisc cleanup. We should always set the number of traffic classes back to 0 here. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
2011-02-15 03:02:23 +08:00
kfree(priv->qdiscs);
}
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
mqprio: Modify mqprio to pass user parameters via ndo_setup_tc. The configurable priority to traffic class mapping and the user specified queue ranges are used to configure the traffic class, overriding the hardware defaults when the 'hw' option is set to 0. However, when the 'hw' option is non-zero, the hardware QOS defaults are used. This patch makes it so that we can pass the data the user provided to ndo_setup_tc. This allows us to pull in the queue configuration if the user requested it as well as any additional hardware offload type requested by using a value other than 1 for the hw value. Finally it also provides a means for the device driver to return the level supported for the offload type via the qopt->hw value. Previously we were just always assuming the value to be 1, in the future values beyond just 1 may be supported. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16 01:39:25 +08:00
if (priv->hw_offload && dev->netdev_ops->ndo_setup_tc) {
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
struct tc_mqprio_qopt_offload mqprio = { { 0 } };
switch (priv->mode) {
case TC_MQPRIO_MODE_DCB:
case TC_MQPRIO_MODE_CHANNEL:
net_sch: mqprio: Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new convention. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-06 14:23:42 +08:00
dev->netdev_ops->ndo_setup_tc(dev,
TC_SETUP_QDISC_MQPRIO,
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
&mqprio);
break;
default:
return;
}
mqprio: Modify mqprio to pass user parameters via ndo_setup_tc. The configurable priority to traffic class mapping and the user specified queue ranges are used to configure the traffic class, overriding the hardware defaults when the 'hw' option is set to 0. However, when the 'hw' option is non-zero, the hardware QOS defaults are used. This patch makes it so that we can pass the data the user provided to ndo_setup_tc. This allows us to pull in the queue configuration if the user requested it as well as any additional hardware offload type requested by using a value other than 1 for the hw value. Finally it also provides a means for the device driver to return the level supported for the offload type via the qopt->hw value. Previously we were just always assuming the value to be 1, in the future values beyond just 1 may be supported. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16 01:39:25 +08:00
} else {
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
netdev_set_num_tc(dev, 0);
mqprio: Modify mqprio to pass user parameters via ndo_setup_tc. The configurable priority to traffic class mapping and the user specified queue ranges are used to configure the traffic class, overriding the hardware defaults when the 'hw' option is set to 0. However, when the 'hw' option is non-zero, the hardware QOS defaults are used. This patch makes it so that we can pass the data the user provided to ndo_setup_tc. This allows us to pull in the queue configuration if the user requested it as well as any additional hardware offload type requested by using a value other than 1 for the hw value. Finally it also provides a means for the device driver to return the level supported for the offload type via the qopt->hw value. Previously we were just always assuming the value to be 1, in the future values beyond just 1 may be supported. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16 01:39:25 +08:00
}
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
}
static int mqprio_parse_opt(struct net_device *dev, struct tc_mqprio_qopt *qopt)
{
int i, j;
/* Verify num_tc is not out of max range */
if (qopt->num_tc > TC_MAX_QUEUE)
return -EINVAL;
/* Verify priority mapping uses valid tcs */
for (i = 0; i < TC_BITMASK + 1; i++) {
if (qopt->prio_tc_map[i] >= qopt->num_tc)
return -EINVAL;
}
mqprio: Change handling of hw u8 to allow for multiple hardware offload modes This patch is meant to allow for support of multiple hardware offload type for a single device. There is currently no bounds checking for the hw member of the mqprio_qopt structure. This results in us being able to pass values from 1 to 255 with all being treated the same. On retreiving the value it is returned as 1 for anything 1 or greater being set. With this change we are currently adding limited bounds checking by defining an enum and using those values to limit the reported hardware offloads. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16 01:39:18 +08:00
/* Limit qopt->hw to maximum supported offload value. Drivers have
* the option of overriding this later if they don't support the a
* given offload type.
*/
if (qopt->hw > TC_MQPRIO_HW_OFFLOAD_MAX)
qopt->hw = TC_MQPRIO_HW_OFFLOAD_MAX;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
mqprio: Change handling of hw u8 to allow for multiple hardware offload modes This patch is meant to allow for support of multiple hardware offload type for a single device. There is currently no bounds checking for the hw member of the mqprio_qopt structure. This results in us being able to pass values from 1 to 255 with all being treated the same. On retreiving the value it is returned as 1 for anything 1 or greater being set. With this change we are currently adding limited bounds checking by defining an enum and using those values to limit the reported hardware offloads. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16 01:39:18 +08:00
/* If hardware offload is requested we will leave it to the device
* to either populate the queue counts itself or to validate the
* provided queue counts. If ndo_setup_tc is not present then
* hardware doesn't support offload and we should return an error.
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
*/
if (qopt->hw)
mqprio: Change handling of hw u8 to allow for multiple hardware offload modes This patch is meant to allow for support of multiple hardware offload type for a single device. There is currently no bounds checking for the hw member of the mqprio_qopt structure. This results in us being able to pass values from 1 to 255 with all being treated the same. On retreiving the value it is returned as 1 for anything 1 or greater being set. With this change we are currently adding limited bounds checking by defining an enum and using those values to limit the reported hardware offloads. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16 01:39:18 +08:00
return dev->netdev_ops->ndo_setup_tc ? 0 : -EINVAL;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
for (i = 0; i < qopt->num_tc; i++) {
unsigned int last = qopt->offset[i] + qopt->count[i];
/* Verify the queue count is in tx range being equal to the
* real_num_tx_queues indicates the last queue is in use.
*/
if (qopt->offset[i] >= dev->real_num_tx_queues ||
!qopt->count[i] ||
last > dev->real_num_tx_queues)
return -EINVAL;
/* Verify that the offset and counts do not overlap */
for (j = i + 1; j < qopt->num_tc; j++) {
if (last > qopt->offset[j])
return -EINVAL;
}
}
return 0;
}
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
static const struct nla_policy mqprio_policy[TCA_MQPRIO_MAX + 1] = {
[TCA_MQPRIO_MODE] = { .len = sizeof(u16) },
[TCA_MQPRIO_SHAPER] = { .len = sizeof(u16) },
[TCA_MQPRIO_MIN_RATE64] = { .type = NLA_NESTED },
[TCA_MQPRIO_MAX_RATE64] = { .type = NLA_NESTED },
};
static int parse_attr(struct nlattr *tb[], int maxtype, struct nlattr *nla,
const struct nla_policy *policy, int len)
{
int nested_len = nla_len(nla) - NLA_ALIGN(len);
if (nested_len >= nla_attr_size(0))
netlink: make validation more configurable for future strictness We currently have two levels of strict validation: 1) liberal (default) - undefined (type >= max) & NLA_UNSPEC attributes accepted - attribute length >= expected accepted - garbage at end of message accepted 2) strict (opt-in) - NLA_UNSPEC attributes accepted - attribute length >= expected accepted Split out parsing strictness into four different options: * TRAILING - check that there's no trailing data after parsing attributes (in message or nested) * MAXTYPE - reject attrs > max known type * UNSPEC - reject attributes with NLA_UNSPEC policy entries * STRICT_ATTRS - strictly validate attribute size The default for future things should be *everything*. The current *_strict() is a combination of TRAILING and MAXTYPE, and is renamed to _deprecated_strict(). The current regular parsing has none of this, and is renamed to *_parse_deprecated(). Additionally it allows us to selectively set one of the new flags even on old policies. Notably, the UNSPEC flag could be useful in this case, since it can be arranged (by filling in the policy) to not be an incompatible userspace ABI change, but would then going forward prevent forgetting attribute entries. Similar can apply to the POLICY flag. We end up with the following renames: * nla_parse -> nla_parse_deprecated * nla_parse_strict -> nla_parse_deprecated_strict * nlmsg_parse -> nlmsg_parse_deprecated * nlmsg_parse_strict -> nlmsg_parse_deprecated_strict * nla_parse_nested -> nla_parse_nested_deprecated * nla_validate_nested -> nla_validate_nested_deprecated Using spatch, of course: @@ expression TB, MAX, HEAD, LEN, POL, EXT; @@ -nla_parse(TB, MAX, HEAD, LEN, POL, EXT) +nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression TB, MAX, NLA, POL, EXT; @@ -nla_parse_nested(TB, MAX, NLA, POL, EXT) +nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT) @@ expression START, MAX, POL, EXT; @@ -nla_validate_nested(START, MAX, POL, EXT) +nla_validate_nested_deprecated(START, MAX, POL, EXT) @@ expression NLH, HDRLEN, MAX, POL, EXT; @@ -nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT) +nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT) For this patch, don't actually add the strict, non-renamed versions yet so that it breaks compile if I get it wrong. Also, while at it, make nla_validate and nla_parse go down to a common __nla_validate_parse() function to avoid code duplication. Ultimately, this allows us to have very strict validation for every new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the next patch, while existing things will continue to work as is. In effect then, this adds fully strict validation for any new command. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-26 20:07:28 +08:00
return nla_parse_deprecated(tb, maxtype,
nla_data(nla) + NLA_ALIGN(len),
nested_len, policy, NULL);
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
memset(tb, 0, sizeof(struct nlattr *) * (maxtype + 1));
return 0;
}
net: sched: sch: add extack for init callback This patch adds extack support for init callback to prepare per-qdisc specific changes for extack. Cc: David Ahern <dsahern@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-21 01:35:13 +08:00
static int mqprio_init(struct Qdisc *sch, struct nlattr *opt,
struct netlink_ext_ack *extack)
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
{
struct net_device *dev = qdisc_dev(sch);
struct mqprio_sched *priv = qdisc_priv(sch);
struct netdev_queue *dev_queue;
struct Qdisc *qdisc;
int i, err = -EOPNOTSUPP;
struct tc_mqprio_qopt *qopt = NULL;
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
struct nlattr *tb[TCA_MQPRIO_MAX + 1];
struct nlattr *attr;
int rem;
mqprio: fix potential null pointer dereference on opt The pointer opt has a null check however before for this check opt is dereferenced when len is initialized, hence we potentially have a null pointer deference on opt. Avoid this by checking for a null opt before dereferencing it. Detected by CoverityScan, CID#1458234 ("Dereference before null check") Fixes: 4e8b86c06269 ("mqprio: Introduce new hardware offload mode and shaper in mqprio") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-17 23:01:30 +08:00
int len;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
BUILD_BUG_ON(TC_MAX_QUEUE != TC_QOPT_MAX_QUEUE);
BUILD_BUG_ON(TC_BITMASK != TC_QOPT_BITMASK);
if (sch->parent != TC_H_ROOT)
return -EOPNOTSUPP;
if (!netif_is_multiqueue(dev))
return -EOPNOTSUPP;
mqprio: Reserve last 32 classid values for HW traffic classes and misc IDs This patch makes a slight tweak to mqprio in order to bring the classid values used back in line with what is used for mq. The general idea is to reserve values :ffe0 - :ffef to identify hardware traffic classes normally reported via dev->num_tc. By doing this we can maintain a consistent behavior with mq for classid where :1 - :ffdf will represent a physical qdisc mapped onto a Tx queue represented by classid - 1, and the traffic classes will be mapped onto a known subset of classid values reserved for our virtual qdiscs. Note I reserved the range from :fff0 - :ffff since this way we might be able to reuse these classid values with clsact and ingress which would mean that for mq, mqprio, ingress, and clsact we should be able to maintain a similar classid layout. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-13 02:38:45 +08:00
/* make certain can allocate enough classids to handle queues */
if (dev->num_tx_queues >= TC_H_MIN_PRIORITY)
return -ENOMEM;
mqprio: Avoid panic if no options are provided Userspace may not provide TCA_OPTIONS, in fact tc currently does so not do so if no arguments are specified on the command line. Return EINVAL instead of panicing. Signed-off-by: Thomas Graf <tgraf@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-22 10:05:07 +08:00
if (!opt || nla_len(opt) < sizeof(*qopt))
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
return -EINVAL;
qopt = nla_data(opt);
if (mqprio_parse_opt(dev, qopt))
return -EINVAL;
mqprio: fix potential null pointer dereference on opt The pointer opt has a null check however before for this check opt is dereferenced when len is initialized, hence we potentially have a null pointer deference on opt. Avoid this by checking for a null opt before dereferencing it. Detected by CoverityScan, CID#1458234 ("Dereference before null check") Fixes: 4e8b86c06269 ("mqprio: Introduce new hardware offload mode and shaper in mqprio") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-17 23:01:30 +08:00
len = nla_len(opt) - NLA_ALIGN(sizeof(*qopt));
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
if (len > 0) {
err = parse_attr(tb, TCA_MQPRIO_MAX, opt, mqprio_policy,
sizeof(*qopt));
if (err < 0)
return err;
if (!qopt->hw)
return -EINVAL;
if (tb[TCA_MQPRIO_MODE]) {
priv->flags |= TC_MQPRIO_F_MODE;
priv->mode = *(u16 *)nla_data(tb[TCA_MQPRIO_MODE]);
}
if (tb[TCA_MQPRIO_SHAPER]) {
priv->flags |= TC_MQPRIO_F_SHAPER;
priv->shaper = *(u16 *)nla_data(tb[TCA_MQPRIO_SHAPER]);
}
if (tb[TCA_MQPRIO_MIN_RATE64]) {
if (priv->shaper != TC_MQPRIO_SHAPER_BW_RATE)
return -EINVAL;
i = 0;
nla_for_each_nested(attr, tb[TCA_MQPRIO_MIN_RATE64],
rem) {
if (nla_type(attr) != TCA_MQPRIO_MIN_RATE64)
return -EINVAL;
if (i >= qopt->num_tc)
break;
priv->min_rate[i] = *(u64 *)nla_data(attr);
i++;
}
priv->flags |= TC_MQPRIO_F_MIN_RATE;
}
if (tb[TCA_MQPRIO_MAX_RATE64]) {
if (priv->shaper != TC_MQPRIO_SHAPER_BW_RATE)
return -EINVAL;
i = 0;
nla_for_each_nested(attr, tb[TCA_MQPRIO_MAX_RATE64],
rem) {
if (nla_type(attr) != TCA_MQPRIO_MAX_RATE64)
return -EINVAL;
if (i >= qopt->num_tc)
break;
priv->max_rate[i] = *(u64 *)nla_data(attr);
i++;
}
priv->flags |= TC_MQPRIO_F_MAX_RATE;
}
}
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
/* pre-allocate qdisc, attachment can't fail */
priv->qdiscs = kcalloc(dev->num_tx_queues, sizeof(priv->qdiscs[0]),
GFP_KERNEL);
net_sched: fix error recovery at qdisc creation Dmitry reported uses after free in qdisc code [1] The problem here is that ops->init() can return an error. qdisc_create_dflt() then call ops->destroy(), while qdisc_create() does _not_ call it. Four qdisc chose to call their own ops->destroy(), assuming their caller would not. This patch makes sure qdisc_create() calls ops->destroy() and fixes the four qdisc to avoid double free. [1] BUG: KASAN: use-after-free in mq_destroy+0x242/0x290 net/sched/sch_mq.c:33 at addr ffff8801d415d440 Read of size 8 by task syz-executor2/5030 CPU: 0 PID: 5030 Comm: syz-executor2 Not tainted 4.3.5-smp-DEV #119 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 0000000000000046 ffff8801b435b870 ffffffff81bbbed4 ffff8801db000400 ffff8801d415d440 ffff8801d415dc40 ffff8801c4988510 ffff8801b435b898 ffffffff816682b1 ffff8801b435b928 ffff8801d415d440 ffff8801c49880c0 Call Trace: [<ffffffff81bbbed4>] __dump_stack lib/dump_stack.c:15 [inline] [<ffffffff81bbbed4>] dump_stack+0x6c/0x98 lib/dump_stack.c:51 [<ffffffff816682b1>] kasan_object_err+0x21/0x70 mm/kasan/report.c:158 [<ffffffff81668524>] print_address_description mm/kasan/report.c:196 [inline] [<ffffffff81668524>] kasan_report_error+0x1b4/0x4b0 mm/kasan/report.c:285 [<ffffffff81668953>] kasan_report mm/kasan/report.c:305 [inline] [<ffffffff81668953>] __asan_report_load8_noabort+0x43/0x50 mm/kasan/report.c:326 [<ffffffff82527b02>] mq_destroy+0x242/0x290 net/sched/sch_mq.c:33 [<ffffffff82524bdd>] qdisc_destroy+0x12d/0x290 net/sched/sch_generic.c:953 [<ffffffff82524e30>] qdisc_create_dflt+0xf0/0x120 net/sched/sch_generic.c:848 [<ffffffff8252550d>] attach_default_qdiscs net/sched/sch_generic.c:1029 [inline] [<ffffffff8252550d>] dev_activate+0x6ad/0x880 net/sched/sch_generic.c:1064 [<ffffffff824b1db1>] __dev_open+0x221/0x320 net/core/dev.c:1403 [<ffffffff824b24ce>] __dev_change_flags+0x15e/0x3e0 net/core/dev.c:6858 [<ffffffff824b27de>] dev_change_flags+0x8e/0x140 net/core/dev.c:6926 [<ffffffff824f5bf6>] dev_ifsioc+0x446/0x890 net/core/dev_ioctl.c:260 [<ffffffff824f61fa>] dev_ioctl+0x1ba/0xb80 net/core/dev_ioctl.c:546 [<ffffffff82430509>] sock_do_ioctl+0x99/0xb0 net/socket.c:879 [<ffffffff82430d30>] sock_ioctl+0x2a0/0x390 net/socket.c:958 [<ffffffff816f3b68>] vfs_ioctl fs/ioctl.c:44 [inline] [<ffffffff816f3b68>] do_vfs_ioctl+0x8a8/0xe50 fs/ioctl.c:611 [<ffffffff816f41a4>] SYSC_ioctl fs/ioctl.c:626 [inline] [<ffffffff816f41a4>] SyS_ioctl+0x94/0xc0 fs/ioctl.c:617 [<ffffffff8123e357>] entry_SYSCALL_64_fastpath+0x12/0x17 Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-11 02:31:49 +08:00
if (!priv->qdiscs)
return -ENOMEM;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
for (i = 0; i < dev->num_tx_queues; i++) {
dev_queue = netdev_get_tx_queue(dev, i);
net: sched: use pfifo_fast for non real queues Some devices declare a high number of TX queues, then set a much lower real_num_tx_queues This cause setups using fq_codel, sfq or fq as the default qdisc to consume more memory than really needed. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-03 00:21:43 +08:00
qdisc = qdisc_create_dflt(dev_queue,
get_default_qdisc_ops(dev, i),
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
TC_H_MAKE(TC_H_MAJ(sch->handle),
net: sch: api: add extack support in qdisc_create_dflt This patch adds extack support for the function qdisc_create_dflt which is a common used function in the tc subsystem. Callers which are interested in the receiving error can assign extack to get a more detailed information why qdisc_create_dflt failed. The function qdisc_create_dflt will also call an init callback which can fail by any per-qdisc specific handling. Cc: David Ahern <dsahern@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-21 01:35:21 +08:00
TC_H_MIN(i + 1)), extack);
net_sched: fix error recovery at qdisc creation Dmitry reported uses after free in qdisc code [1] The problem here is that ops->init() can return an error. qdisc_create_dflt() then call ops->destroy(), while qdisc_create() does _not_ call it. Four qdisc chose to call their own ops->destroy(), assuming their caller would not. This patch makes sure qdisc_create() calls ops->destroy() and fixes the four qdisc to avoid double free. [1] BUG: KASAN: use-after-free in mq_destroy+0x242/0x290 net/sched/sch_mq.c:33 at addr ffff8801d415d440 Read of size 8 by task syz-executor2/5030 CPU: 0 PID: 5030 Comm: syz-executor2 Not tainted 4.3.5-smp-DEV #119 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 0000000000000046 ffff8801b435b870 ffffffff81bbbed4 ffff8801db000400 ffff8801d415d440 ffff8801d415dc40 ffff8801c4988510 ffff8801b435b898 ffffffff816682b1 ffff8801b435b928 ffff8801d415d440 ffff8801c49880c0 Call Trace: [<ffffffff81bbbed4>] __dump_stack lib/dump_stack.c:15 [inline] [<ffffffff81bbbed4>] dump_stack+0x6c/0x98 lib/dump_stack.c:51 [<ffffffff816682b1>] kasan_object_err+0x21/0x70 mm/kasan/report.c:158 [<ffffffff81668524>] print_address_description mm/kasan/report.c:196 [inline] [<ffffffff81668524>] kasan_report_error+0x1b4/0x4b0 mm/kasan/report.c:285 [<ffffffff81668953>] kasan_report mm/kasan/report.c:305 [inline] [<ffffffff81668953>] __asan_report_load8_noabort+0x43/0x50 mm/kasan/report.c:326 [<ffffffff82527b02>] mq_destroy+0x242/0x290 net/sched/sch_mq.c:33 [<ffffffff82524bdd>] qdisc_destroy+0x12d/0x290 net/sched/sch_generic.c:953 [<ffffffff82524e30>] qdisc_create_dflt+0xf0/0x120 net/sched/sch_generic.c:848 [<ffffffff8252550d>] attach_default_qdiscs net/sched/sch_generic.c:1029 [inline] [<ffffffff8252550d>] dev_activate+0x6ad/0x880 net/sched/sch_generic.c:1064 [<ffffffff824b1db1>] __dev_open+0x221/0x320 net/core/dev.c:1403 [<ffffffff824b24ce>] __dev_change_flags+0x15e/0x3e0 net/core/dev.c:6858 [<ffffffff824b27de>] dev_change_flags+0x8e/0x140 net/core/dev.c:6926 [<ffffffff824f5bf6>] dev_ifsioc+0x446/0x890 net/core/dev_ioctl.c:260 [<ffffffff824f61fa>] dev_ioctl+0x1ba/0xb80 net/core/dev_ioctl.c:546 [<ffffffff82430509>] sock_do_ioctl+0x99/0xb0 net/socket.c:879 [<ffffffff82430d30>] sock_ioctl+0x2a0/0x390 net/socket.c:958 [<ffffffff816f3b68>] vfs_ioctl fs/ioctl.c:44 [inline] [<ffffffff816f3b68>] do_vfs_ioctl+0x8a8/0xe50 fs/ioctl.c:611 [<ffffffff816f41a4>] SYSC_ioctl fs/ioctl.c:626 [inline] [<ffffffff816f41a4>] SyS_ioctl+0x94/0xc0 fs/ioctl.c:617 [<ffffffff8123e357>] entry_SYSCALL_64_fastpath+0x12/0x17 Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-11 02:31:49 +08:00
if (!qdisc)
return -ENOMEM;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
priv->qdiscs[i] = qdisc;
net_sched: fix qdisc_tree_decrease_qlen() races qdisc_tree_decrease_qlen() suffers from two problems on multiqueue devices. One problem is that it updates sch->q.qlen and sch->qstats.drops on the mq/mqprio root qdisc, while it should not : Daniele reported underflows errors : [ 681.774821] PAX: sch->q.qlen: 0 n: 1 [ 681.774825] PAX: size overflow detected in function qdisc_tree_decrease_qlen net/sched/sch_api.c:769 cicus.693_49 min, count: 72, decl: qlen; num: 0; context: sk_buff_head; [ 681.774954] CPU: 2 PID: 19 Comm: ksoftirqd/2 Tainted: G O 4.2.6.201511282239-1-grsec #1 [ 681.774955] Hardware name: ASUSTeK COMPUTER INC. X302LJ/X302LJ, BIOS X302LJ.202 03/05/2015 [ 681.774956] ffffffffa9a04863 0000000000000000 0000000000000000 ffffffffa990ff7c [ 681.774959] ffffc90000d3bc38 ffffffffa95d2810 0000000000000007 ffffffffa991002b [ 681.774960] ffffc90000d3bc68 ffffffffa91a44f4 0000000000000001 0000000000000001 [ 681.774962] Call Trace: [ 681.774967] [<ffffffffa95d2810>] dump_stack+0x4c/0x7f [ 681.774970] [<ffffffffa91a44f4>] report_size_overflow+0x34/0x50 [ 681.774972] [<ffffffffa94d17e2>] qdisc_tree_decrease_qlen+0x152/0x160 [ 681.774976] [<ffffffffc02694b1>] fq_codel_dequeue+0x7b1/0x820 [sch_fq_codel] [ 681.774978] [<ffffffffc02680a0>] ? qdisc_peek_dequeued+0xa0/0xa0 [sch_fq_codel] [ 681.774980] [<ffffffffa94cd92d>] __qdisc_run+0x4d/0x1d0 [ 681.774983] [<ffffffffa949b2b2>] net_tx_action+0xc2/0x160 [ 681.774985] [<ffffffffa90664c1>] __do_softirq+0xf1/0x200 [ 681.774987] [<ffffffffa90665ee>] run_ksoftirqd+0x1e/0x30 [ 681.774989] [<ffffffffa90896b0>] smpboot_thread_fn+0x150/0x260 [ 681.774991] [<ffffffffa9089560>] ? sort_range+0x40/0x40 [ 681.774992] [<ffffffffa9085fe4>] kthread+0xe4/0x100 [ 681.774994] [<ffffffffa9085f00>] ? kthread_worker_fn+0x170/0x170 [ 681.774995] [<ffffffffa95d8d1e>] ret_from_fork+0x3e/0x70 mq/mqprio have their own ways to report qlen/drops by folding stats on all their queues, with appropriate locking. A second problem is that qdisc_tree_decrease_qlen() calls qdisc_lookup() without proper locking : concurrent qdisc updates could corrupt the list that qdisc_match_from_root() parses to find a qdisc given its handle. Fix first problem adding a TCQ_F_NOPARENT qdisc flag that qdisc_tree_decrease_qlen() can use to abort its tree traversal, as soon as it meets a mq/mqprio qdisc children. Second problem can be fixed by RCU protection. Qdisc are already freed after RCU grace period, so qdisc_list_add() and qdisc_list_del() simply have to use appropriate rcu list variants. A future patch will add a per struct netdev_queue list anchor, so that qdisc_tree_decrease_qlen() can have more efficient lookups. Reported-by: Daniele Fucini <dfucini@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Cong Wang <cwang@twopensource.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-02 12:08:51 +08:00
qdisc->flags |= TCQ_F_ONETXQUEUE | TCQ_F_NOPARENT;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
}
/* If the mqprio options indicate that hardware should own
* the queue mapping then run ndo_setup_tc otherwise use the
* supplied and verified mapping
*/
if (qopt->hw) {
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
struct tc_mqprio_qopt_offload mqprio = {.qopt = *qopt};
net: rework setup_tc ndo op to consume general tc operand This patch updates setup_tc so we can pass additional parameters into the ndo op in a generic way. To do this we provide structured union and type flag. This lets each classifier and qdisc provide its own set of attributes without having to add new ndo ops or grow the signature of the callback. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-17 13:16:43 +08:00
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
switch (priv->mode) {
case TC_MQPRIO_MODE_DCB:
if (priv->shaper != TC_MQPRIO_SHAPER_DCB)
return -EINVAL;
break;
case TC_MQPRIO_MODE_CHANNEL:
mqprio.flags = priv->flags;
if (priv->flags & TC_MQPRIO_F_MODE)
mqprio.mode = priv->mode;
if (priv->flags & TC_MQPRIO_F_SHAPER)
mqprio.shaper = priv->shaper;
if (priv->flags & TC_MQPRIO_F_MIN_RATE)
for (i = 0; i < mqprio.qopt.num_tc; i++)
mqprio.min_rate[i] = priv->min_rate[i];
if (priv->flags & TC_MQPRIO_F_MAX_RATE)
for (i = 0; i < mqprio.qopt.num_tc; i++)
mqprio.max_rate[i] = priv->max_rate[i];
break;
default:
return -EINVAL;
}
err = dev->netdev_ops->ndo_setup_tc(dev,
net_sch: mqprio: Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new convention. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-06 14:23:42 +08:00
TC_SETUP_QDISC_MQPRIO,
net: sched: get rid of struct tc_to_netdev Get rid of struct tc_to_netdev which is now just unnecessary container and rather pass per-type structures down to drivers directly. Along with that, consolidate the naming of per-type structure variables in cls_*. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-07 16:15:32 +08:00
&mqprio);
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
if (err)
net_sched: fix error recovery at qdisc creation Dmitry reported uses after free in qdisc code [1] The problem here is that ops->init() can return an error. qdisc_create_dflt() then call ops->destroy(), while qdisc_create() does _not_ call it. Four qdisc chose to call their own ops->destroy(), assuming their caller would not. This patch makes sure qdisc_create() calls ops->destroy() and fixes the four qdisc to avoid double free. [1] BUG: KASAN: use-after-free in mq_destroy+0x242/0x290 net/sched/sch_mq.c:33 at addr ffff8801d415d440 Read of size 8 by task syz-executor2/5030 CPU: 0 PID: 5030 Comm: syz-executor2 Not tainted 4.3.5-smp-DEV #119 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 0000000000000046 ffff8801b435b870 ffffffff81bbbed4 ffff8801db000400 ffff8801d415d440 ffff8801d415dc40 ffff8801c4988510 ffff8801b435b898 ffffffff816682b1 ffff8801b435b928 ffff8801d415d440 ffff8801c49880c0 Call Trace: [<ffffffff81bbbed4>] __dump_stack lib/dump_stack.c:15 [inline] [<ffffffff81bbbed4>] dump_stack+0x6c/0x98 lib/dump_stack.c:51 [<ffffffff816682b1>] kasan_object_err+0x21/0x70 mm/kasan/report.c:158 [<ffffffff81668524>] print_address_description mm/kasan/report.c:196 [inline] [<ffffffff81668524>] kasan_report_error+0x1b4/0x4b0 mm/kasan/report.c:285 [<ffffffff81668953>] kasan_report mm/kasan/report.c:305 [inline] [<ffffffff81668953>] __asan_report_load8_noabort+0x43/0x50 mm/kasan/report.c:326 [<ffffffff82527b02>] mq_destroy+0x242/0x290 net/sched/sch_mq.c:33 [<ffffffff82524bdd>] qdisc_destroy+0x12d/0x290 net/sched/sch_generic.c:953 [<ffffffff82524e30>] qdisc_create_dflt+0xf0/0x120 net/sched/sch_generic.c:848 [<ffffffff8252550d>] attach_default_qdiscs net/sched/sch_generic.c:1029 [inline] [<ffffffff8252550d>] dev_activate+0x6ad/0x880 net/sched/sch_generic.c:1064 [<ffffffff824b1db1>] __dev_open+0x221/0x320 net/core/dev.c:1403 [<ffffffff824b24ce>] __dev_change_flags+0x15e/0x3e0 net/core/dev.c:6858 [<ffffffff824b27de>] dev_change_flags+0x8e/0x140 net/core/dev.c:6926 [<ffffffff824f5bf6>] dev_ifsioc+0x446/0x890 net/core/dev_ioctl.c:260 [<ffffffff824f61fa>] dev_ioctl+0x1ba/0xb80 net/core/dev_ioctl.c:546 [<ffffffff82430509>] sock_do_ioctl+0x99/0xb0 net/socket.c:879 [<ffffffff82430d30>] sock_ioctl+0x2a0/0x390 net/socket.c:958 [<ffffffff816f3b68>] vfs_ioctl fs/ioctl.c:44 [inline] [<ffffffff816f3b68>] do_vfs_ioctl+0x8a8/0xe50 fs/ioctl.c:611 [<ffffffff816f41a4>] SYSC_ioctl fs/ioctl.c:626 [inline] [<ffffffff816f41a4>] SyS_ioctl+0x94/0xc0 fs/ioctl.c:617 [<ffffffff8123e357>] entry_SYSCALL_64_fastpath+0x12/0x17 Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-11 02:31:49 +08:00
return err;
mqprio: Change handling of hw u8 to allow for multiple hardware offload modes This patch is meant to allow for support of multiple hardware offload type for a single device. There is currently no bounds checking for the hw member of the mqprio_qopt structure. This results in us being able to pass values from 1 to 255 with all being treated the same. On retreiving the value it is returned as 1 for anything 1 or greater being set. With this change we are currently adding limited bounds checking by defining an enum and using those values to limit the reported hardware offloads. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16 01:39:18 +08:00
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
priv->hw_offload = mqprio.qopt.hw;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
} else {
netdev_set_num_tc(dev, qopt->num_tc);
for (i = 0; i < qopt->num_tc; i++)
netdev_set_tc_queue(dev, i,
qopt->count[i], qopt->offset[i]);
}
/* Always use supplied priority mappings */
for (i = 0; i < TC_BITMASK + 1; i++)
netdev_set_prio_tc_map(dev, i, qopt->prio_tc_map[i]);
sch->flags |= TCQ_F_MQROOT;
return 0;
}
static void mqprio_attach(struct Qdisc *sch)
{
struct net_device *dev = qdisc_dev(sch);
struct mqprio_sched *priv = qdisc_priv(sch);
pkt_sched: give visibility to mq slave qdiscs Commit 6da7c8fcbcbd ("qdisc: allow setting default queuing discipline") added the ability to change default qdisc from pfifo_fast to say fq But as most modern ethernet devices are multiqueue, we cant really see all the statistics from "tc -s qdisc show", as the default root qdisc is mq. This patch adds the calls to qdisc_list_add() to mq and mqprio Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-06 03:12:02 +08:00
struct Qdisc *qdisc, *old;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
unsigned int ntx;
/* Attach underlying qdisc */
for (ntx = 0; ntx < dev->num_tx_queues; ntx++) {
qdisc = priv->qdiscs[ntx];
pkt_sched: give visibility to mq slave qdiscs Commit 6da7c8fcbcbd ("qdisc: allow setting default queuing discipline") added the ability to change default qdisc from pfifo_fast to say fq But as most modern ethernet devices are multiqueue, we cant really see all the statistics from "tc -s qdisc show", as the default root qdisc is mq. This patch adds the calls to qdisc_list_add() to mq and mqprio Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-06 03:12:02 +08:00
old = dev_graft_qdisc(qdisc->dev_queue, qdisc);
if (old)
net: sched: rename qdisc_destroy() to qdisc_put() Current implementation of qdisc_destroy() decrements Qdisc reference counter and only actually destroy Qdisc if reference counter value reached zero. Rename qdisc_destroy() to qdisc_put() in order for it to better describe the way in which this function currently implemented and used. Extract code that deallocates Qdisc into new private qdisc_destroy() function. It is intended to be shared between regular qdisc_put() and its unlocked version that is introduced in next patch in this series. Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-25 00:22:50 +08:00
qdisc_put(old);
pkt_sched: give visibility to mq slave qdiscs Commit 6da7c8fcbcbd ("qdisc: allow setting default queuing discipline") added the ability to change default qdisc from pfifo_fast to say fq But as most modern ethernet devices are multiqueue, we cant really see all the statistics from "tc -s qdisc show", as the default root qdisc is mq. This patch adds the calls to qdisc_list_add() to mq and mqprio Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-06 03:12:02 +08:00
if (ntx < dev->real_num_tx_queues)
net: sched: make default fifo qdiscs appear in the dump The original reason [1] for having hidden qdiscs (potential scalability issues in qdisc_match_from_root() with single linked list in case of large amount of qdiscs) has been invalidated by 59cc1f61f0 ("net: sched: convert qdisc linked list to hashtable"). This allows us for bringing more clarity and determinism into the dump by making default pfifo qdiscs visible. We're not turning this on by default though, at it was deemed [2] too intrusive / unnecessary change of default behavior towards userspace. Instead, TCA_DUMP_INVISIBLE netlink attribute is introduced, which allows applications to request complete qdisc hierarchy dump, including the ones that have always been implicit/invisible. Singleton noop_qdisc stays invisible, as teaching the whole infrastructure about singletons would require quite some surgery with very little gain (seeing no qdisc or seeing noop qdisc in the dump is probably setting the same user expectation). [1] http://lkml.kernel.org/r/1460732328.10638.74.camel@edumazet-glaptop3.roam.corp.google.com [2] http://lkml.kernel.org/r/20161021.105935.1907696543877061916.davem@davemloft.net Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-08 23:03:32 +08:00
qdisc_hash_add(qdisc, false);
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
}
kfree(priv->qdiscs);
priv->qdiscs = NULL;
}
static struct netdev_queue *mqprio_queue_get(struct Qdisc *sch,
unsigned long cl)
{
struct net_device *dev = qdisc_dev(sch);
mqprio: Reserve last 32 classid values for HW traffic classes and misc IDs This patch makes a slight tweak to mqprio in order to bring the classid values used back in line with what is used for mq. The general idea is to reserve values :ffe0 - :ffef to identify hardware traffic classes normally reported via dev->num_tc. By doing this we can maintain a consistent behavior with mq for classid where :1 - :ffdf will represent a physical qdisc mapped onto a Tx queue represented by classid - 1, and the traffic classes will be mapped onto a known subset of classid values reserved for our virtual qdiscs. Note I reserved the range from :fff0 - :ffff since this way we might be able to reuse these classid values with clsact and ingress which would mean that for mq, mqprio, ingress, and clsact we should be able to maintain a similar classid layout. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-13 02:38:45 +08:00
unsigned long ntx = cl - 1;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
if (ntx >= dev->num_tx_queues)
return NULL;
return netdev_get_tx_queue(dev, ntx);
}
static int mqprio_graft(struct Qdisc *sch, unsigned long cl, struct Qdisc *new,
net: sched: sch: add extack for graft callback This patch adds extack support for graft callback to prepare per-qdisc specific changes for extack. Cc: David Ahern <dsahern@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-21 01:35:17 +08:00
struct Qdisc **old, struct netlink_ext_ack *extack)
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
{
struct net_device *dev = qdisc_dev(sch);
struct netdev_queue *dev_queue = mqprio_queue_get(sch, cl);
if (!dev_queue)
return -EINVAL;
if (dev->flags & IFF_UP)
dev_deactivate(dev);
*old = dev_graft_qdisc(dev_queue, new);
pkt_sched: avoid requeues if possible With BQL being deployed, we can more likely have following behavior : We dequeue a packet from qdisc in dequeue_skb(), then we realize target tx queue is in XOFF state in sch_direct_xmit(), and we have to hold the skb into gso_skb for later. This shows in stats (tc -s qdisc dev eth0) as requeues. Problem of these requeues is that high priority packets can not be dequeued as long as this (possibly low prio and big TSO packet) is not removed from gso_skb. At 1Gbps speed, a full size TSO packet is 500 us of extra latency. In some cases, we know that all packets dequeued from a qdisc are for a particular and known txq : - If device is non multi queue - For all MQ/MQPRIO slave qdiscs This patch introduces a new qdisc flag, TCQ_F_ONETXQUEUE to mark this capability, so that dequeue_skb() is allowed to dequeue a packet only if the associated txq is not stopped. This indeed reduce latencies for high prio packets (or improve fairness with sfq/fq_codel), and almost remove qdisc 'requeues'. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-11 23:54:33 +08:00
if (new)
net_sched: fix qdisc_tree_decrease_qlen() races qdisc_tree_decrease_qlen() suffers from two problems on multiqueue devices. One problem is that it updates sch->q.qlen and sch->qstats.drops on the mq/mqprio root qdisc, while it should not : Daniele reported underflows errors : [ 681.774821] PAX: sch->q.qlen: 0 n: 1 [ 681.774825] PAX: size overflow detected in function qdisc_tree_decrease_qlen net/sched/sch_api.c:769 cicus.693_49 min, count: 72, decl: qlen; num: 0; context: sk_buff_head; [ 681.774954] CPU: 2 PID: 19 Comm: ksoftirqd/2 Tainted: G O 4.2.6.201511282239-1-grsec #1 [ 681.774955] Hardware name: ASUSTeK COMPUTER INC. X302LJ/X302LJ, BIOS X302LJ.202 03/05/2015 [ 681.774956] ffffffffa9a04863 0000000000000000 0000000000000000 ffffffffa990ff7c [ 681.774959] ffffc90000d3bc38 ffffffffa95d2810 0000000000000007 ffffffffa991002b [ 681.774960] ffffc90000d3bc68 ffffffffa91a44f4 0000000000000001 0000000000000001 [ 681.774962] Call Trace: [ 681.774967] [<ffffffffa95d2810>] dump_stack+0x4c/0x7f [ 681.774970] [<ffffffffa91a44f4>] report_size_overflow+0x34/0x50 [ 681.774972] [<ffffffffa94d17e2>] qdisc_tree_decrease_qlen+0x152/0x160 [ 681.774976] [<ffffffffc02694b1>] fq_codel_dequeue+0x7b1/0x820 [sch_fq_codel] [ 681.774978] [<ffffffffc02680a0>] ? qdisc_peek_dequeued+0xa0/0xa0 [sch_fq_codel] [ 681.774980] [<ffffffffa94cd92d>] __qdisc_run+0x4d/0x1d0 [ 681.774983] [<ffffffffa949b2b2>] net_tx_action+0xc2/0x160 [ 681.774985] [<ffffffffa90664c1>] __do_softirq+0xf1/0x200 [ 681.774987] [<ffffffffa90665ee>] run_ksoftirqd+0x1e/0x30 [ 681.774989] [<ffffffffa90896b0>] smpboot_thread_fn+0x150/0x260 [ 681.774991] [<ffffffffa9089560>] ? sort_range+0x40/0x40 [ 681.774992] [<ffffffffa9085fe4>] kthread+0xe4/0x100 [ 681.774994] [<ffffffffa9085f00>] ? kthread_worker_fn+0x170/0x170 [ 681.774995] [<ffffffffa95d8d1e>] ret_from_fork+0x3e/0x70 mq/mqprio have their own ways to report qlen/drops by folding stats on all their queues, with appropriate locking. A second problem is that qdisc_tree_decrease_qlen() calls qdisc_lookup() without proper locking : concurrent qdisc updates could corrupt the list that qdisc_match_from_root() parses to find a qdisc given its handle. Fix first problem adding a TCQ_F_NOPARENT qdisc flag that qdisc_tree_decrease_qlen() can use to abort its tree traversal, as soon as it meets a mq/mqprio qdisc children. Second problem can be fixed by RCU protection. Qdisc are already freed after RCU grace period, so qdisc_list_add() and qdisc_list_del() simply have to use appropriate rcu list variants. A future patch will add a per struct netdev_queue list anchor, so that qdisc_tree_decrease_qlen() can have more efficient lookups. Reported-by: Daniele Fucini <dfucini@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Cong Wang <cwang@twopensource.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-02 12:08:51 +08:00
new->flags |= TCQ_F_ONETXQUEUE | TCQ_F_NOPARENT;
pkt_sched: avoid requeues if possible With BQL being deployed, we can more likely have following behavior : We dequeue a packet from qdisc in dequeue_skb(), then we realize target tx queue is in XOFF state in sch_direct_xmit(), and we have to hold the skb into gso_skb for later. This shows in stats (tc -s qdisc dev eth0) as requeues. Problem of these requeues is that high priority packets can not be dequeued as long as this (possibly low prio and big TSO packet) is not removed from gso_skb. At 1Gbps speed, a full size TSO packet is 500 us of extra latency. In some cases, we know that all packets dequeued from a qdisc are for a particular and known txq : - If device is non multi queue - For all MQ/MQPRIO slave qdiscs This patch introduces a new qdisc flag, TCQ_F_ONETXQUEUE to mark this capability, so that dequeue_skb() is allowed to dequeue a packet only if the associated txq is not stopped. This indeed reduce latencies for high prio packets (or improve fairness with sfq/fq_codel), and almost remove qdisc 'requeues'. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-11 23:54:33 +08:00
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
if (dev->flags & IFF_UP)
dev_activate(dev);
return 0;
}
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
static int dump_rates(struct mqprio_sched *priv,
struct tc_mqprio_qopt *opt, struct sk_buff *skb)
{
struct nlattr *nest;
int i;
if (priv->flags & TC_MQPRIO_F_MIN_RATE) {
netlink: make nla_nest_start() add NLA_F_NESTED flag Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most netlink based interfaces (including recently added ones) are still not setting it in kernel generated messages. Without the flag, message parsers not aware of attribute semantics (e.g. wireshark dissector or libmnl's mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display the structure of their contents. Unfortunately we cannot just add the flag everywhere as there may be userspace applications which check nlattr::nla_type directly rather than through a helper masking out the flags. Therefore the patch renames nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start() as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually are rewritten to use nla_nest_start(). Except for changes in include/net/netlink.h, the patch was generated using this semantic patch: @@ expression E1, E2; @@ -nla_nest_start(E1, E2) +nla_nest_start_noflag(E1, E2) @@ expression E1, E2; @@ -nla_nest_start_noflag(E1, E2 | NLA_F_NESTED) +nla_nest_start(E1, E2) Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-26 17:13:06 +08:00
nest = nla_nest_start_noflag(skb, TCA_MQPRIO_MIN_RATE64);
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
if (!nest)
goto nla_put_failure;
for (i = 0; i < opt->num_tc; i++) {
if (nla_put(skb, TCA_MQPRIO_MIN_RATE64,
sizeof(priv->min_rate[i]),
&priv->min_rate[i]))
goto nla_put_failure;
}
nla_nest_end(skb, nest);
}
if (priv->flags & TC_MQPRIO_F_MAX_RATE) {
netlink: make nla_nest_start() add NLA_F_NESTED flag Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most netlink based interfaces (including recently added ones) are still not setting it in kernel generated messages. Without the flag, message parsers not aware of attribute semantics (e.g. wireshark dissector or libmnl's mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display the structure of their contents. Unfortunately we cannot just add the flag everywhere as there may be userspace applications which check nlattr::nla_type directly rather than through a helper masking out the flags. Therefore the patch renames nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start() as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually are rewritten to use nla_nest_start(). Except for changes in include/net/netlink.h, the patch was generated using this semantic patch: @@ expression E1, E2; @@ -nla_nest_start(E1, E2) +nla_nest_start_noflag(E1, E2) @@ expression E1, E2; @@ -nla_nest_start_noflag(E1, E2 | NLA_F_NESTED) +nla_nest_start(E1, E2) Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-26 17:13:06 +08:00
nest = nla_nest_start_noflag(skb, TCA_MQPRIO_MAX_RATE64);
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
if (!nest)
goto nla_put_failure;
for (i = 0; i < opt->num_tc; i++) {
if (nla_put(skb, TCA_MQPRIO_MAX_RATE64,
sizeof(priv->max_rate[i]),
&priv->max_rate[i]))
goto nla_put_failure;
}
nla_nest_end(skb, nest);
}
return 0;
nla_put_failure:
nla_nest_cancel(skb, nest);
return -1;
}
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
static int mqprio_dump(struct Qdisc *sch, struct sk_buff *skb)
{
struct net_device *dev = qdisc_dev(sch);
struct mqprio_sched *priv = qdisc_priv(sch);
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
struct nlattr *nla = (struct nlattr *)skb_tail_pointer(skb);
net_sched: sch_mqprio: dont leak kernel memory mqprio_dump() should make sure all fields of struct tc_mqprio_qopt are initialized. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-26 15:21:57 +08:00
struct tc_mqprio_qopt opt = { 0 };
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
struct Qdisc *qdisc;
net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio The sch_mqprio qdisc creates a sub-qdisc per tx queue which are then called independently for enqueue and dequeue operations. However statistics are aggregated and pushed up to the "master" qdisc. This patch adds support for any of the sub-qdiscs to be per cpu statistic qdiscs. To handle this case add a check when calculating stats and aggregate the per cpu stats if needed. Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 01:57:39 +08:00
unsigned int ntx, tc;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
sch->q.qlen = 0;
memset(&sch->bstats, 0, sizeof(sch->bstats));
memset(&sch->qstats, 0, sizeof(sch->qstats));
net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio The sch_mqprio qdisc creates a sub-qdisc per tx queue which are then called independently for enqueue and dequeue operations. However statistics are aggregated and pushed up to the "master" qdisc. This patch adds support for any of the sub-qdiscs to be per cpu statistic qdiscs. To handle this case add a check when calculating stats and aggregate the per cpu stats if needed. Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 01:57:39 +08:00
/* MQ supports lockless qdiscs. However, statistics accounting needs
* to account for all, none, or a mix of locked and unlocked child
* qdiscs. Percpu stats are added to counters in-band and locking
* qdisc totals are added at end.
*/
for (ntx = 0; ntx < dev->num_tx_queues; ntx++) {
qdisc = netdev_get_tx_queue(dev, ntx)->qdisc_sleeping;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
spin_lock_bh(qdisc_lock(qdisc));
net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio The sch_mqprio qdisc creates a sub-qdisc per tx queue which are then called independently for enqueue and dequeue operations. However statistics are aggregated and pushed up to the "master" qdisc. This patch adds support for any of the sub-qdiscs to be per cpu statistic qdiscs. To handle this case add a check when calculating stats and aggregate the per cpu stats if needed. Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 01:57:39 +08:00
if (qdisc_is_percpu_stats(qdisc)) {
__u32 qlen = qdisc_qlen_sum(qdisc);
__gnet_stats_copy_basic(NULL, &sch->bstats,
qdisc->cpu_bstats,
&qdisc->bstats);
__gnet_stats_copy_queue(&sch->qstats,
qdisc->cpu_qstats,
&qdisc->qstats, qlen);
} else {
sch->q.qlen += qdisc->q.qlen;
sch->bstats.bytes += qdisc->bstats.bytes;
sch->bstats.packets += qdisc->bstats.packets;
sch->qstats.backlog += qdisc->qstats.backlog;
sch->qstats.drops += qdisc->qstats.drops;
sch->qstats.requeues += qdisc->qstats.requeues;
sch->qstats.overlimits += qdisc->qstats.overlimits;
}
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
spin_unlock_bh(qdisc_lock(qdisc));
}
opt.num_tc = netdev_get_num_tc(dev);
memcpy(opt.prio_tc_map, dev->prio_tc_map, sizeof(opt.prio_tc_map));
mqprio: Change handling of hw u8 to allow for multiple hardware offload modes This patch is meant to allow for support of multiple hardware offload type for a single device. There is currently no bounds checking for the hw member of the mqprio_qopt structure. This results in us being able to pass values from 1 to 255 with all being treated the same. On retreiving the value it is returned as 1 for anything 1 or greater being set. With this change we are currently adding limited bounds checking by defining an enum and using those values to limit the reported hardware offloads. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-16 01:39:18 +08:00
opt.hw = priv->hw_offload;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio The sch_mqprio qdisc creates a sub-qdisc per tx queue which are then called independently for enqueue and dequeue operations. However statistics are aggregated and pushed up to the "master" qdisc. This patch adds support for any of the sub-qdiscs to be per cpu statistic qdiscs. To handle this case add a check when calculating stats and aggregate the per cpu stats if needed. Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 01:57:39 +08:00
for (tc = 0; tc < netdev_get_num_tc(dev); tc++) {
opt.count[tc] = dev->tc_to_txq[tc].count;
opt.offset[tc] = dev->tc_to_txq[tc].offset;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
}
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
if (nla_put(skb, TCA_OPTIONS, NLA_ALIGN(sizeof(opt)), &opt))
goto nla_put_failure;
if ((priv->flags & TC_MQPRIO_F_MODE) &&
nla_put_u16(skb, TCA_MQPRIO_MODE, priv->mode))
goto nla_put_failure;
if ((priv->flags & TC_MQPRIO_F_SHAPER) &&
nla_put_u16(skb, TCA_MQPRIO_SHAPER, priv->shaper))
goto nla_put_failure;
if ((priv->flags & TC_MQPRIO_F_MIN_RATE ||
priv->flags & TC_MQPRIO_F_MAX_RATE) &&
(dump_rates(priv, &opt, skb) != 0))
pkt_sched: Stop using NLA_PUT*(). These macros contain a hidden goto, and are thus extremely error prone and make code hard to audit. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-29 17:11:39 +08:00
goto nla_put_failure;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
return nla_nest_end(skb, nla);
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
nla_put_failure:
mqprio: Introduce new hardware offload mode and shaper in mqprio The offload types currently supported in mqprio are 0 (no offload) and 1 (offload only TCs) by setting these values for the 'hw' option. If offloads are supported by setting the 'hw' option to 1, the default offload mode is 'dcb' where only the TC values are offloaded to the device. This patch introduces a new hardware offload mode called 'channel' with 'hw' set to 1 in mqprio which makes full use of the mqprio options, the TCs, the queue configurations and the QoS parameters for the TCs. This is achieved through a new netlink attribute for the 'mode' option which takes values such as 'dcb' (default) and 'channel'. The 'channel' mode also supports QoS attributes for traffic class such as minimum and maximum values for bandwidth rate limits. This patch enables configuring additional HW shaper attributes associated with a traffic class. Currently the shaper for bandwidth rate limiting is supported which takes options such as minimum and maximum bandwidth rates and are offloaded to the hardware in the 'channel' mode. The min and max limits for bandwidth rates are provided by the user along with the TCs and the queue configurations when creating the mqprio qdisc. The interface can be extended to support new HW shapers in future through the 'shaper' attribute. Introduces a new data structure 'tc_mqprio_qopt_offload' for offloading mqprio queue options and use this to be shared between the kernel and device driver. This contains a copy of the existing data structure for mqprio queue options. This new data structure can be extended when adding new attributes for traffic class such as mode, shaper, shaper parameters (bandwidth rate limits). The existing data structure for mqprio queue options will be shared between the kernel and userspace. Example: queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ min_rate 1Gbit 2Gbit max_rate 4Gbit 5Gbit To dump the bandwidth rates: qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit min_rate:1Gbit 2Gbit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-09-07 19:00:06 +08:00
nlmsg_trim(skb, nla);
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
return -1;
}
static struct Qdisc *mqprio_leaf(struct Qdisc *sch, unsigned long cl)
{
struct netdev_queue *dev_queue = mqprio_queue_get(sch, cl);
if (!dev_queue)
return NULL;
return dev_queue->qdisc_sleeping;
}
net_sched: remove tc class reference counting For TC classes, their ->get() and ->put() are always paired, and the reference counting is completely useless, because: 1) For class modification and dumping paths, we already hold RTNL lock, so all of these ->get(),->change(),->put() are atomic. 2) For filter bindiing/unbinding, we use other reference counter than this one, and they should have RTNL lock too. 3) For ->qlen_notify(), it is special because it is called on ->enqueue() path, but we already hold qdisc tree lock there, and we hold this tree lock when graft or delete the class too, so it should not be gone or changed until we release the tree lock. Therefore, this patch removes ->get() and ->put(), but: 1) Adds a new ->find() to find the pointer to a class by classid, no refcnt. 2) Move the original class destroy upon the last refcnt into ->delete(), right after releasing tree lock. This is fine because the class is already removed from hash when holding the lock. For those who also use ->put() as ->unbind(), just rename them to reflect this change. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-25 07:51:29 +08:00
static unsigned long mqprio_find(struct Qdisc *sch, u32 classid)
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
{
struct net_device *dev = qdisc_dev(sch);
unsigned int ntx = TC_H_MIN(classid);
mqprio: Reserve last 32 classid values for HW traffic classes and misc IDs This patch makes a slight tweak to mqprio in order to bring the classid values used back in line with what is used for mq. The general idea is to reserve values :ffe0 - :ffef to identify hardware traffic classes normally reported via dev->num_tc. By doing this we can maintain a consistent behavior with mq for classid where :1 - :ffdf will represent a physical qdisc mapped onto a Tx queue represented by classid - 1, and the traffic classes will be mapped onto a known subset of classid values reserved for our virtual qdiscs. Note I reserved the range from :fff0 - :ffff since this way we might be able to reuse these classid values with clsact and ingress which would mean that for mq, mqprio, ingress, and clsact we should be able to maintain a similar classid layout. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-13 02:38:45 +08:00
/* There are essentially two regions here that have valid classid
* values. The first region will have a classid value of 1 through
* num_tx_queues. All of these are backed by actual Qdiscs.
*/
if (ntx < TC_H_MIN_PRIORITY)
return (ntx <= dev->num_tx_queues) ? ntx : 0;
/* The second region represents the hardware traffic classes. These
* are represented by classid values of TC_H_MIN_PRIORITY through
* TC_H_MIN_PRIORITY + netdev_get_num_tc - 1
*/
return ((ntx - TC_H_MIN_PRIORITY) < netdev_get_num_tc(dev)) ? ntx : 0;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
}
static int mqprio_dump_class(struct Qdisc *sch, unsigned long cl,
struct sk_buff *skb, struct tcmsg *tcm)
{
mqprio: Reserve last 32 classid values for HW traffic classes and misc IDs This patch makes a slight tweak to mqprio in order to bring the classid values used back in line with what is used for mq. The general idea is to reserve values :ffe0 - :ffef to identify hardware traffic classes normally reported via dev->num_tc. By doing this we can maintain a consistent behavior with mq for classid where :1 - :ffdf will represent a physical qdisc mapped onto a Tx queue represented by classid - 1, and the traffic classes will be mapped onto a known subset of classid values reserved for our virtual qdiscs. Note I reserved the range from :fff0 - :ffff since this way we might be able to reuse these classid values with clsact and ingress which would mean that for mq, mqprio, ingress, and clsact we should be able to maintain a similar classid layout. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-13 02:38:45 +08:00
if (cl < TC_H_MIN_PRIORITY) {
struct netdev_queue *dev_queue = mqprio_queue_get(sch, cl);
struct net_device *dev = qdisc_dev(sch);
int tc = netdev_txq_to_tc(dev, cl - 1);
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
mqprio: Reserve last 32 classid values for HW traffic classes and misc IDs This patch makes a slight tweak to mqprio in order to bring the classid values used back in line with what is used for mq. The general idea is to reserve values :ffe0 - :ffef to identify hardware traffic classes normally reported via dev->num_tc. By doing this we can maintain a consistent behavior with mq for classid where :1 - :ffdf will represent a physical qdisc mapped onto a Tx queue represented by classid - 1, and the traffic classes will be mapped onto a known subset of classid values reserved for our virtual qdiscs. Note I reserved the range from :fff0 - :ffff since this way we might be able to reuse these classid values with clsact and ingress which would mean that for mq, mqprio, ingress, and clsact we should be able to maintain a similar classid layout. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-13 02:38:45 +08:00
tcm->tcm_parent = (tc < 0) ? 0 :
TC_H_MAKE(TC_H_MAJ(sch->handle),
TC_H_MIN(tc + TC_H_MIN_PRIORITY));
tcm->tcm_info = dev_queue->qdisc_sleeping->handle;
} else {
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
tcm->tcm_parent = TC_H_ROOT;
tcm->tcm_info = 0;
}
tcm->tcm_handle |= TC_H_MIN(cl);
return 0;
}
static int mqprio_dump_class_stats(struct Qdisc *sch, unsigned long cl,
mqprio: cleanups * make qdisc_ops local * add sparse annotation about expected unlock/unlock in dump_class_stats * fix indentation Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-23 17:06:51 +08:00
struct gnet_dump *d)
__releases(d->lock)
__acquires(d->lock)
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
{
mqprio: Reserve last 32 classid values for HW traffic classes and misc IDs This patch makes a slight tweak to mqprio in order to bring the classid values used back in line with what is used for mq. The general idea is to reserve values :ffe0 - :ffef to identify hardware traffic classes normally reported via dev->num_tc. By doing this we can maintain a consistent behavior with mq for classid where :1 - :ffdf will represent a physical qdisc mapped onto a Tx queue represented by classid - 1, and the traffic classes will be mapped onto a known subset of classid values reserved for our virtual qdiscs. Note I reserved the range from :fff0 - :ffff since this way we might be able to reuse these classid values with clsact and ingress which would mean that for mq, mqprio, ingress, and clsact we should be able to maintain a similar classid layout. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-13 02:38:45 +08:00
if (cl >= TC_H_MIN_PRIORITY) {
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
int i;
net: sched: restrict use of qstats qlen This removes the use of qstats->qlen variable from the classifiers and makes it an explicit argument to gnet_stats_copy_queue(). The qlen represents the qdisc queue length and is packed into the qstats at the last moment before passnig to user space. By handling it explicitely we avoid, in the percpu stats case, having to figure out which per_cpu variable to put it in. It would probably be best to remove it from qstats completely but qstats is a user space ABI and can't be broken. A future patch could make an internal only qstats structure that would avoid having to allocate an additional u32 variable on the Qdisc struct. This would make the qstats struct 128bits instead of 128+32. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-29 02:53:57 +08:00
__u32 qlen = 0;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
struct gnet_stats_queue qstats = {0};
struct gnet_stats_basic_packed bstats = {0};
mqprio: Reserve last 32 classid values for HW traffic classes and misc IDs This patch makes a slight tweak to mqprio in order to bring the classid values used back in line with what is used for mq. The general idea is to reserve values :ffe0 - :ffef to identify hardware traffic classes normally reported via dev->num_tc. By doing this we can maintain a consistent behavior with mq for classid where :1 - :ffdf will represent a physical qdisc mapped onto a Tx queue represented by classid - 1, and the traffic classes will be mapped onto a known subset of classid values reserved for our virtual qdiscs. Note I reserved the range from :fff0 - :ffff since this way we might be able to reuse these classid values with clsact and ingress which would mean that for mq, mqprio, ingress, and clsact we should be able to maintain a similar classid layout. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-13 02:38:45 +08:00
struct net_device *dev = qdisc_dev(sch);
struct netdev_tc_txq tc = dev->tc_to_txq[cl & TC_BITMASK];
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
/* Drop lock here it will be reclaimed before touching
* statistics this is required because the d->lock we
* hold here is the look on dev_queue->qdisc_sleeping
* also acquired below.
*/
net: sched: do not acquire qdisc spinlock in qdisc/class stats dump Large tc dumps (tc -s {qdisc|class} sh dev ethX) done by Google BwE host agent [1] are problematic at scale : For each qdisc/class found in the dump, we currently lock the root qdisc spinlock in order to get stats. Sampling stats every 5 seconds from thousands of HTB classes is a challenge when the root qdisc spinlock is under high pressure. Not only the dumps take time, they also slow down the fast path (queue/dequeue packets) by 10 % to 20 % in some cases. An audit of existing qdiscs showed that sch_fq_codel is the only qdisc that might need the qdisc lock in fq_codel_dump_stats() and fq_codel_dump_class_stats() In v2 of this patch, I now use the Qdisc running seqcount to provide consistent reads of packets/bytes counters, regardless of 32/64 bit arches. I also changed rate estimators to use the same infrastructure so that they no longer need to lock root qdisc lock. [1] http://static.googleusercontent.com/media/research.google.com/en//pubs/archive/43838.pdf Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: Kevin Athey <kda@google.com> Cc: Xiaotian Pei <xiaotian@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-07 00:37:16 +08:00
if (d->lock)
spin_unlock_bh(d->lock);
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
for (i = tc.offset; i < tc.offset + tc.count; i++) {
net: qdisc: use rcu prefix and silence sparse warnings Add __rcu notation to qdisc handling by doing this we can make smatch output more legible. And anyways some of the cases should be using rcu_dereference() see qdisc_all_tx_empty(), qdisc_tx_chainging(), and so on. Also *wake_queue() API is commonly called from driver timer routines without rcu lock or rtnl lock. So I added rcu_read_lock() blocks around netif_wake_subqueue and netif_tx_wake_queue. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13 11:04:52 +08:00
struct netdev_queue *q = netdev_get_tx_queue(dev, i);
net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio The sch_mqprio qdisc creates a sub-qdisc per tx queue which are then called independently for enqueue and dequeue operations. However statistics are aggregated and pushed up to the "master" qdisc. This patch adds support for any of the sub-qdiscs to be per cpu statistic qdiscs. To handle this case add a check when calculating stats and aggregate the per cpu stats if needed. Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 01:57:39 +08:00
struct Qdisc *qdisc = rtnl_dereference(q->qdisc);
struct gnet_stats_basic_cpu __percpu *cpu_bstats = NULL;
struct gnet_stats_queue __percpu *cpu_qstats = NULL;
net: qdisc: use rcu prefix and silence sparse warnings Add __rcu notation to qdisc handling by doing this we can make smatch output more legible. And anyways some of the cases should be using rcu_dereference() see qdisc_all_tx_empty(), qdisc_tx_chainging(), and so on. Also *wake_queue() API is commonly called from driver timer routines without rcu lock or rtnl lock. So I added rcu_read_lock() blocks around netif_wake_subqueue and netif_tx_wake_queue. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13 11:04:52 +08:00
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
spin_lock_bh(qdisc_lock(qdisc));
net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio The sch_mqprio qdisc creates a sub-qdisc per tx queue which are then called independently for enqueue and dequeue operations. However statistics are aggregated and pushed up to the "master" qdisc. This patch adds support for any of the sub-qdiscs to be per cpu statistic qdiscs. To handle this case add a check when calculating stats and aggregate the per cpu stats if needed. Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 01:57:39 +08:00
if (qdisc_is_percpu_stats(qdisc)) {
cpu_bstats = qdisc->cpu_bstats;
cpu_qstats = qdisc->cpu_qstats;
}
qlen = qdisc_qlen_sum(qdisc);
__gnet_stats_copy_basic(NULL, &sch->bstats,
cpu_bstats, &qdisc->bstats);
__gnet_stats_copy_queue(&sch->qstats,
cpu_qstats,
&qdisc->qstats,
qlen);
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
spin_unlock_bh(qdisc_lock(qdisc));
}
net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio The sch_mqprio qdisc creates a sub-qdisc per tx queue which are then called independently for enqueue and dequeue operations. However statistics are aggregated and pushed up to the "master" qdisc. This patch adds support for any of the sub-qdiscs to be per cpu statistic qdiscs. To handle this case add a check when calculating stats and aggregate the per cpu stats if needed. Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-08 01:57:39 +08:00
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
/* Reclaim root sleeping lock before completing stats */
net: sched: do not acquire qdisc spinlock in qdisc/class stats dump Large tc dumps (tc -s {qdisc|class} sh dev ethX) done by Google BwE host agent [1] are problematic at scale : For each qdisc/class found in the dump, we currently lock the root qdisc spinlock in order to get stats. Sampling stats every 5 seconds from thousands of HTB classes is a challenge when the root qdisc spinlock is under high pressure. Not only the dumps take time, they also slow down the fast path (queue/dequeue packets) by 10 % to 20 % in some cases. An audit of existing qdiscs showed that sch_fq_codel is the only qdisc that might need the qdisc lock in fq_codel_dump_stats() and fq_codel_dump_class_stats() In v2 of this patch, I now use the Qdisc running seqcount to provide consistent reads of packets/bytes counters, regardless of 32/64 bit arches. I also changed rate estimators to use the same infrastructure so that they no longer need to lock root qdisc lock. [1] http://static.googleusercontent.com/media/research.google.com/en//pubs/archive/43838.pdf Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: Kevin Athey <kda@google.com> Cc: Xiaotian Pei <xiaotian@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-07 00:37:16 +08:00
if (d->lock)
spin_lock_bh(d->lock);
if (gnet_stats_copy_basic(NULL, d, NULL, &bstats) < 0 ||
net: sched: enable per cpu qstats After previous patches to simplify qstats the qstats can be made per cpu with a packed union in Qdisc struct. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-29 02:54:24 +08:00
gnet_stats_copy_queue(d, NULL, &qstats, qlen) < 0)
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
return -1;
} else {
struct netdev_queue *dev_queue = mqprio_queue_get(sch, cl);
sch = dev_queue->qdisc_sleeping;
net: sched: fix `tc -s class show` no bstats on class with nolock subqueues When a classful qdisc's child qdisc has set the flag TCQ_F_CPUSTATS (pfifo_fast for example), the child qdisc's cpu_bstats should be passed to gnet_stats_copy_basic(), but many classful qdisc didn't do that. As a result, `tc -s class show dev DEV` always return 0 for bytes and packets in this case. Pass the child qdisc's cpu_bstats to gnet_stats_copy_basic() to fix this issue. The qstats also has this problem, but it has been fixed in 5dd431b6b9 ("net: sched: introduce and use qstats read...") and bstats still remains buggy. Fixes: 22e0f8b9322c ("net: sched: make bstats per cpu and estimator RCU safe") Signed-off-by: Dust Li <dust.li@linux.alibaba.com> Signed-off-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-28 14:29:09 +08:00
if (gnet_stats_copy_basic(qdisc_root_sleeping_running(sch), d,
sch->cpu_bstats, &sch->bstats) < 0 ||
net: sched: introduce and use qstats read helpers Classful qdiscs can't access directly the child qdiscs backlog length: if such qdisc is NOLOCK, per CPU values should be accounted instead. Most qdiscs no not respect the above. As a result, qstats fetching for most classful qdisc is currently incorrect: if the child qdisc is NOLOCK, it always reports 0 len backlog. This change introduces a pair of helpers to safely fetch both backlog and qlen and use them in stats class dumping functions, fixing the above issue and cleaning a bit the code. DRR needs also to access the child qdisc queue length, so it needs custom handling. Fixes: c5ad119fb6c0 ("net: sched: pfifo_fast use skb_array") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-28 23:53:12 +08:00
qdisc_qstats_copy(d, sch) < 0)
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
return -1;
}
return 0;
}
static void mqprio_walk(struct Qdisc *sch, struct qdisc_walker *arg)
{
struct net_device *dev = qdisc_dev(sch);
unsigned long ntx;
if (arg->stop)
return;
/* Walk hierarchy with a virtual class per tc */
arg->count = arg->skip;
mqprio: Reserve last 32 classid values for HW traffic classes and misc IDs This patch makes a slight tweak to mqprio in order to bring the classid values used back in line with what is used for mq. The general idea is to reserve values :ffe0 - :ffef to identify hardware traffic classes normally reported via dev->num_tc. By doing this we can maintain a consistent behavior with mq for classid where :1 - :ffdf will represent a physical qdisc mapped onto a Tx queue represented by classid - 1, and the traffic classes will be mapped onto a known subset of classid values reserved for our virtual qdiscs. Note I reserved the range from :fff0 - :ffff since this way we might be able to reuse these classid values with clsact and ingress which would mean that for mq, mqprio, ingress, and clsact we should be able to maintain a similar classid layout. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-13 02:38:45 +08:00
for (ntx = arg->skip; ntx < netdev_get_num_tc(dev); ntx++) {
if (arg->fn(sch, ntx + TC_H_MIN_PRIORITY, arg) < 0) {
arg->stop = 1;
return;
}
arg->count++;
}
/* Pad the values and skip over unused traffic classes */
if (ntx < TC_MAX_QUEUE) {
arg->count = TC_MAX_QUEUE;
ntx = TC_MAX_QUEUE;
}
/* Reset offset, sort out remaining per-queue qdiscs */
for (ntx -= TC_MAX_QUEUE; ntx < dev->num_tx_queues; ntx++) {
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
if (arg->fn(sch, ntx + 1, arg) < 0) {
arg->stop = 1;
mqprio: Reserve last 32 classid values for HW traffic classes and misc IDs This patch makes a slight tweak to mqprio in order to bring the classid values used back in line with what is used for mq. The general idea is to reserve values :ffe0 - :ffef to identify hardware traffic classes normally reported via dev->num_tc. By doing this we can maintain a consistent behavior with mq for classid where :1 - :ffdf will represent a physical qdisc mapped onto a Tx queue represented by classid - 1, and the traffic classes will be mapped onto a known subset of classid values reserved for our virtual qdiscs. Note I reserved the range from :fff0 - :ffff since this way we might be able to reuse these classid values with clsact and ingress which would mean that for mq, mqprio, ingress, and clsact we should be able to maintain a similar classid layout. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-13 02:38:45 +08:00
return;
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
}
arg->count++;
}
}
net/sched: Add select_queue() class_ops for mqprio When replacing a child qdisc from mqprio, tc_modify_qdisc() must fetch the netdev_queue pointer that the current child qdisc is associated with before creating the new qdisc. Currently, when using mqprio as root qdisc, the kernel will end up getting the queue #0 pointer from the mqprio (root qdisc), which leaves any new child qdisc with a possibly wrong netdev_queue pointer. Implementing the Qdisc_class_ops select_queue() on mqprio fixes this issue and avoid an inconsistent state when child qdiscs are replaced. Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Tested-by: Henrik Austad <henrik@austad.us> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-10-17 09:01:25 +08:00
static struct netdev_queue *mqprio_select_queue(struct Qdisc *sch,
struct tcmsg *tcm)
{
return mqprio_queue_get(sch, TC_H_MIN(tcm->tcm_parent));
}
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
static const struct Qdisc_class_ops mqprio_class_ops = {
.graft = mqprio_graft,
.leaf = mqprio_leaf,
net_sched: remove tc class reference counting For TC classes, their ->get() and ->put() are always paired, and the reference counting is completely useless, because: 1) For class modification and dumping paths, we already hold RTNL lock, so all of these ->get(),->change(),->put() are atomic. 2) For filter bindiing/unbinding, we use other reference counter than this one, and they should have RTNL lock too. 3) For ->qlen_notify(), it is special because it is called on ->enqueue() path, but we already hold qdisc tree lock there, and we hold this tree lock when graft or delete the class too, so it should not be gone or changed until we release the tree lock. Therefore, this patch removes ->get() and ->put(), but: 1) Adds a new ->find() to find the pointer to a class by classid, no refcnt. 2) Move the original class destroy upon the last refcnt into ->delete(), right after releasing tree lock. This is fine because the class is already removed from hash when holding the lock. For those who also use ->put() as ->unbind(), just rename them to reflect this change. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-25 07:51:29 +08:00
.find = mqprio_find,
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
.walk = mqprio_walk,
.dump = mqprio_dump_class,
.dump_stats = mqprio_dump_class_stats,
net/sched: Add select_queue() class_ops for mqprio When replacing a child qdisc from mqprio, tc_modify_qdisc() must fetch the netdev_queue pointer that the current child qdisc is associated with before creating the new qdisc. Currently, when using mqprio as root qdisc, the kernel will end up getting the queue #0 pointer from the mqprio (root qdisc), which leaves any new child qdisc with a possibly wrong netdev_queue pointer. Implementing the Qdisc_class_ops select_queue() on mqprio fixes this issue and avoid an inconsistent state when child qdiscs are replaced. Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Tested-by: Henrik Austad <henrik@austad.us> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-10-17 09:01:25 +08:00
.select_queue = mqprio_select_queue,
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
};
mqprio: cleanups * make qdisc_ops local * add sparse annotation about expected unlock/unlock in dump_class_stats * fix indentation Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-23 17:06:51 +08:00
static struct Qdisc_ops mqprio_qdisc_ops __read_mostly = {
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 16:06:09 +08:00
.cl_ops = &mqprio_class_ops,
.id = "mqprio",
.priv_size = sizeof(struct mqprio_sched),
.init = mqprio_init,
.destroy = mqprio_destroy,
.attach = mqprio_attach,
.dump = mqprio_dump,
.owner = THIS_MODULE,
};
static int __init mqprio_module_init(void)
{
return register_qdisc(&mqprio_qdisc_ops);
}
static void __exit mqprio_module_exit(void)
{
unregister_qdisc(&mqprio_qdisc_ops);
}
module_init(mqprio_module_init);
module_exit(mqprio_module_exit);
MODULE_LICENSE("GPL");
Copy Permalink