kernel_optimize_test/include/acpi/acrestyp.h

679 lines
19 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0 */
/******************************************************************************
*
* Name: acrestyp.h - Defines, types, and structures for resource descriptors
*
* Copyright (C) 2000 - 2019, Intel Corp.
*
*****************************************************************************/
#ifndef __ACRESTYP_H__
#define __ACRESTYP_H__
/*
* Definitions for Resource Attributes
*/
typedef u16 acpi_rs_length; /* Resource Length field is fixed at 16 bits */
typedef u32 acpi_rsdesc_size; /* Max Resource Descriptor size is (Length+3) = (64K-1)+3 */
/*
* Memory Attributes
*/
#define ACPI_READ_ONLY_MEMORY (u8) 0x00
#define ACPI_READ_WRITE_MEMORY (u8) 0x01
#define ACPI_NON_CACHEABLE_MEMORY (u8) 0x00
#define ACPI_CACHABLE_MEMORY (u8) 0x01
#define ACPI_WRITE_COMBINING_MEMORY (u8) 0x02
#define ACPI_PREFETCHABLE_MEMORY (u8) 0x03
/*! [Begin] no source code translation */
/*
* IO Attributes
* The ISA IO ranges are: n000-n0FFh, n400-n4FFh, n800-n8FFh, nC00-nCFFh.
* The non-ISA IO ranges are: n100-n3FFh, n500-n7FFh, n900-nBFFh, nCD0-nFFFh.
*/
/*! [End] no source code translation !*/
#define ACPI_NON_ISA_ONLY_RANGES (u8) 0x01
#define ACPI_ISA_ONLY_RANGES (u8) 0x02
#define ACPI_ENTIRE_RANGE (ACPI_NON_ISA_ONLY_RANGES | ACPI_ISA_ONLY_RANGES)
/* Type of translation - 1=Sparse, 0=Dense */
#define ACPI_SPARSE_TRANSLATION (u8) 0x01
/*
* IO Port Descriptor Decode
*/
#define ACPI_DECODE_10 (u8) 0x00 /* 10-bit IO address decode */
#define ACPI_DECODE_16 (u8) 0x01 /* 16-bit IO address decode */
/*
* Interrupt attributes - used in multiple descriptors
*/
/* Triggering */
#define ACPI_LEVEL_SENSITIVE (u8) 0x00
#define ACPI_EDGE_SENSITIVE (u8) 0x01
/* Polarity */
#define ACPI_ACTIVE_HIGH (u8) 0x00
#define ACPI_ACTIVE_LOW (u8) 0x01
#define ACPI_ACTIVE_BOTH (u8) 0x02
/* Sharing */
#define ACPI_EXCLUSIVE (u8) 0x00
#define ACPI_SHARED (u8) 0x01
/* Wake */
#define ACPI_NOT_WAKE_CAPABLE (u8) 0x00
#define ACPI_WAKE_CAPABLE (u8) 0x01
/*
* DMA Attributes
*/
#define ACPI_COMPATIBILITY (u8) 0x00
#define ACPI_TYPE_A (u8) 0x01
#define ACPI_TYPE_B (u8) 0x02
#define ACPI_TYPE_F (u8) 0x03
#define ACPI_NOT_BUS_MASTER (u8) 0x00
#define ACPI_BUS_MASTER (u8) 0x01
#define ACPI_TRANSFER_8 (u8) 0x00
#define ACPI_TRANSFER_8_16 (u8) 0x01
#define ACPI_TRANSFER_16 (u8) 0x02
/*
* Start Dependent Functions Priority definitions
*/
#define ACPI_GOOD_CONFIGURATION (u8) 0x00
#define ACPI_ACCEPTABLE_CONFIGURATION (u8) 0x01
#define ACPI_SUB_OPTIMAL_CONFIGURATION (u8) 0x02
/*
* 16, 32 and 64-bit Address Descriptor resource types
*/
#define ACPI_MEMORY_RANGE (u8) 0x00
#define ACPI_IO_RANGE (u8) 0x01
#define ACPI_BUS_NUMBER_RANGE (u8) 0x02
#define ACPI_ADDRESS_NOT_FIXED (u8) 0x00
#define ACPI_ADDRESS_FIXED (u8) 0x01
#define ACPI_POS_DECODE (u8) 0x00
#define ACPI_SUB_DECODE (u8) 0x01
/* Producer/Consumer */
#define ACPI_PRODUCER (u8) 0x00
#define ACPI_CONSUMER (u8) 0x01
/*
* If possible, pack the following structures to byte alignment
*/
#ifndef ACPI_MISALIGNMENT_NOT_SUPPORTED
#pragma pack(1)
#endif
/* UUID data structures for use in vendor-defined resource descriptors */
struct acpi_uuid {
u8 data[ACPI_UUID_LENGTH];
};
struct acpi_vendor_uuid {
u8 subtype;
u8 data[ACPI_UUID_LENGTH];
};
/*
* Structures used to describe device resources
*/
struct acpi_resource_irq {
u8 descriptor_length;
u8 triggering;
u8 polarity;
u8 shareable;
u8 wake_capable;
u8 interrupt_count;
u8 interrupts[1];
};
struct acpi_resource_dma {
u8 type;
u8 bus_master;
u8 transfer;
u8 channel_count;
u8 channels[1];
};
struct acpi_resource_start_dependent {
u8 descriptor_length;
u8 compatibility_priority;
u8 performance_robustness;
};
/*
* The END_DEPENDENT_FUNCTIONS_RESOURCE struct is not
* needed because it has no fields
*/
struct acpi_resource_io {
u8 io_decode;
u8 alignment;
u8 address_length;
u16 minimum;
u16 maximum;
};
struct acpi_resource_fixed_io {
u16 address;
u8 address_length;
};
struct acpi_resource_fixed_dma {
u16 request_lines;
u16 channels;
u8 width;
};
/* Values for Width field above */
#define ACPI_DMA_WIDTH8 0
#define ACPI_DMA_WIDTH16 1
#define ACPI_DMA_WIDTH32 2
#define ACPI_DMA_WIDTH64 3
#define ACPI_DMA_WIDTH128 4
#define ACPI_DMA_WIDTH256 5
struct acpi_resource_vendor {
u16 byte_length;
u8 byte_data[1];
};
/* Vendor resource with UUID info (introduced in ACPI 3.0) */
struct acpi_resource_vendor_typed {
u16 byte_length;
u8 uuid_subtype;
u8 uuid[ACPI_UUID_LENGTH];
u8 byte_data[1];
};
struct acpi_resource_end_tag {
u8 checksum;
};
struct acpi_resource_memory24 {
u8 write_protect;
u16 minimum;
u16 maximum;
u16 alignment;
u16 address_length;
};
struct acpi_resource_memory32 {
u8 write_protect;
u32 minimum;
u32 maximum;
u32 alignment;
u32 address_length;
};
struct acpi_resource_fixed_memory32 {
u8 write_protect;
u32 address;
u32 address_length;
};
struct acpi_memory_attribute {
u8 write_protect;
u8 caching;
u8 range_type;
u8 translation;
};
struct acpi_io_attribute {
u8 range_type;
u8 translation;
u8 translation_type;
u8 reserved1;
};
union acpi_resource_attribute {
struct acpi_memory_attribute mem;
struct acpi_io_attribute io;
/* Used for the *word_space macros */
u8 type_specific;
};
struct acpi_resource_label {
u16 string_length;
char *string_ptr;
};
struct acpi_resource_source {
u8 index;
u16 string_length;
char *string_ptr;
};
/* Fields common to all address descriptors, 16/32/64 bit */
#define ACPI_RESOURCE_ADDRESS_COMMON \
u8 resource_type; \
u8 producer_consumer; \
u8 decode; \
u8 min_address_fixed; \
u8 max_address_fixed; \
union acpi_resource_attribute info;
struct acpi_address16_attribute {
u16 granularity;
u16 minimum;
u16 maximum;
u16 translation_offset;
u16 address_length;
};
struct acpi_address32_attribute {
u32 granularity;
u32 minimum;
u32 maximum;
u32 translation_offset;
u32 address_length;
};
struct acpi_address64_attribute {
u64 granularity;
u64 minimum;
u64 maximum;
u64 translation_offset;
u64 address_length;
};
struct acpi_resource_address {
ACPI_RESOURCE_ADDRESS_COMMON};
struct acpi_resource_address16 {
ACPI_RESOURCE_ADDRESS_COMMON struct acpi_address16_attribute address;
struct acpi_resource_source resource_source;
};
struct acpi_resource_address32 {
ACPI_RESOURCE_ADDRESS_COMMON struct acpi_address32_attribute address;
struct acpi_resource_source resource_source;
};
struct acpi_resource_address64 {
ACPI_RESOURCE_ADDRESS_COMMON struct acpi_address64_attribute address;
struct acpi_resource_source resource_source;
};
struct acpi_resource_extended_address64 {
ACPI_RESOURCE_ADDRESS_COMMON u8 revision_ID;
struct acpi_address64_attribute address;
u64 type_specific;
};
struct acpi_resource_extended_irq {
u8 producer_consumer;
u8 triggering;
u8 polarity;
u8 shareable;
u8 wake_capable;
u8 interrupt_count;
struct acpi_resource_source resource_source;
u32 interrupts[1];
};
struct acpi_resource_generic_register {
u8 space_id;
u8 bit_width;
u8 bit_offset;
u8 access_size;
u64 address;
};
struct acpi_resource_gpio {
u8 revision_id;
u8 connection_type;
u8 producer_consumer; /* For values, see Producer/Consumer above */
u8 pin_config;
u8 shareable; /* For values, see Interrupt Attributes above */
u8 wake_capable; /* For values, see Interrupt Attributes above */
u8 io_restriction;
u8 triggering; /* For values, see Interrupt Attributes above */
u8 polarity; /* For values, see Interrupt Attributes above */
u16 drive_strength;
u16 debounce_timeout;
u16 pin_table_length;
u16 vendor_length;
struct acpi_resource_source resource_source;
u16 *pin_table;
u8 *vendor_data;
};
/* Values for GPIO connection_type field above */
#define ACPI_RESOURCE_GPIO_TYPE_INT 0
#define ACPI_RESOURCE_GPIO_TYPE_IO 1
/* Values for pin_config field above */
#define ACPI_PIN_CONFIG_DEFAULT 0
#define ACPI_PIN_CONFIG_PULLUP 1
#define ACPI_PIN_CONFIG_PULLDOWN 2
#define ACPI_PIN_CONFIG_NOPULL 3
/* Values for io_restriction field above */
#define ACPI_IO_RESTRICT_NONE 0
#define ACPI_IO_RESTRICT_INPUT 1
#define ACPI_IO_RESTRICT_OUTPUT 2
#define ACPI_IO_RESTRICT_NONE_PRESERVE 3
/* Common structure for I2C, SPI, and UART serial descriptors */
#define ACPI_RESOURCE_SERIAL_COMMON \
u8 revision_id; \
u8 type; \
u8 producer_consumer; /* For values, see Producer/Consumer above */\
u8 slave_mode; \
u8 connection_sharing; \
u8 type_revision_id; \
u16 type_data_length; \
u16 vendor_length; \
struct acpi_resource_source resource_source; \
u8 *vendor_data;
struct acpi_resource_common_serialbus {
ACPI_RESOURCE_SERIAL_COMMON};
/* Values for the Type field above */
#define ACPI_RESOURCE_SERIAL_TYPE_I2C 1
#define ACPI_RESOURCE_SERIAL_TYPE_SPI 2
#define ACPI_RESOURCE_SERIAL_TYPE_UART 3
/* Values for slave_mode field above */
#define ACPI_CONTROLLER_INITIATED 0
#define ACPI_DEVICE_INITIATED 1
struct acpi_resource_i2c_serialbus {
ACPI_RESOURCE_SERIAL_COMMON u8 access_mode;
u16 slave_address;
u32 connection_speed;
};
/* Values for access_mode field above */
#define ACPI_I2C_7BIT_MODE 0
#define ACPI_I2C_10BIT_MODE 1
struct acpi_resource_spi_serialbus {
ACPI_RESOURCE_SERIAL_COMMON u8 wire_mode;
u8 device_polarity;
u8 data_bit_length;
u8 clock_phase;
u8 clock_polarity;
u16 device_selection;
u32 connection_speed;
};
/* Values for wire_mode field above */
#define ACPI_SPI_4WIRE_MODE 0
#define ACPI_SPI_3WIRE_MODE 1
/* Values for device_polarity field above */
#define ACPI_SPI_ACTIVE_LOW 0
#define ACPI_SPI_ACTIVE_HIGH 1
/* Values for clock_phase field above */
#define ACPI_SPI_FIRST_PHASE 0
#define ACPI_SPI_SECOND_PHASE 1
/* Values for clock_polarity field above */
#define ACPI_SPI_START_LOW 0
#define ACPI_SPI_START_HIGH 1
struct acpi_resource_uart_serialbus {
ACPI_RESOURCE_SERIAL_COMMON u8 endian;
u8 data_bits;
u8 stop_bits;
u8 flow_control;
u8 parity;
u8 lines_enabled;
u16 rx_fifo_size;
u16 tx_fifo_size;
u32 default_baud_rate;
};
/* Values for Endian field above */
#define ACPI_UART_LITTLE_ENDIAN 0
#define ACPI_UART_BIG_ENDIAN 1
/* Values for data_bits field above */
#define ACPI_UART_5_DATA_BITS 0
#define ACPI_UART_6_DATA_BITS 1
#define ACPI_UART_7_DATA_BITS 2
#define ACPI_UART_8_DATA_BITS 3
#define ACPI_UART_9_DATA_BITS 4
/* Values for stop_bits field above */
#define ACPI_UART_NO_STOP_BITS 0
#define ACPI_UART_1_STOP_BIT 1
#define ACPI_UART_1P5_STOP_BITS 2
#define ACPI_UART_2_STOP_BITS 3
/* Values for flow_control field above */
#define ACPI_UART_FLOW_CONTROL_NONE 0
#define ACPI_UART_FLOW_CONTROL_HW 1
#define ACPI_UART_FLOW_CONTROL_XON_XOFF 2
/* Values for Parity field above */
#define ACPI_UART_PARITY_NONE 0
#define ACPI_UART_PARITY_EVEN 1
#define ACPI_UART_PARITY_ODD 2
#define ACPI_UART_PARITY_MARK 3
#define ACPI_UART_PARITY_SPACE 4
/* Values for lines_enabled bitfield above */
#define ACPI_UART_CARRIER_DETECT (1<<2)
#define ACPI_UART_RING_INDICATOR (1<<3)
#define ACPI_UART_DATA_SET_READY (1<<4)
#define ACPI_UART_DATA_TERMINAL_READY (1<<5)
#define ACPI_UART_CLEAR_TO_SEND (1<<6)
#define ACPI_UART_REQUEST_TO_SEND (1<<7)
struct acpi_resource_pin_function {
u8 revision_id;
u8 pin_config;
u8 shareable; /* For values, see Interrupt Attributes above */
u16 function_number;
u16 pin_table_length;
u16 vendor_length;
struct acpi_resource_source resource_source;
u16 *pin_table;
u8 *vendor_data;
};
ACPICA: ACPI 6.2: Add support for PinConfig() resource ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906 ACPI 6.2 introduced a new resource that is used to specify fine-grained configuration of a pin or set of pins used by a device. The ASL syntax of this new resource looks like: PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue, ResourceSource, ResourceSourceIndex, ResourceUsage, DescriptorName, Vendordata) {Pin List} PinConfigType is an integer with following accepted values: 0x00 (Default) - No configuration is applied to the pin 0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor 0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor 0x03 (Bias Default) - Set to default biasing 0x04 (Bias Disable) - All bias settings will be disabled 0x05 (Bias High Impedance) - Configure the pin as hi_z 0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where it drives the last value on a tristate bus 0x07 (Drive Open Drain) - Configure the pin into open drain state 0x08 (Drive Open Source) - Configure the pin into open source state 0x09 (Drive Push Pull) - Configure the pin into push-pull state 0x0a (Drive Strength) - How much the pin can supply current 0x0b (Slew Rate) - Configure slew rate of the pin 0x0c (Input Debounce) - Enable input debouncer for the pin 0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin 0x0e - 0x7f - Reserved 0x80 - 0xff - Vendor defined types The PinConfigValue depends on the type and is expressed as units suitable for that type (for example bias uses Ohms). Link: https://github.com/acpica/acpica/commit/a06fdba6 Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-05 16:39:19 +08:00
struct acpi_resource_pin_config {
u8 revision_id;
u8 producer_consumer; /* For values, see Producer/Consumer above */
u8 shareable; /* For values, see Interrupt Attributes above */
ACPICA: ACPI 6.2: Add support for PinConfig() resource ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906 ACPI 6.2 introduced a new resource that is used to specify fine-grained configuration of a pin or set of pins used by a device. The ASL syntax of this new resource looks like: PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue, ResourceSource, ResourceSourceIndex, ResourceUsage, DescriptorName, Vendordata) {Pin List} PinConfigType is an integer with following accepted values: 0x00 (Default) - No configuration is applied to the pin 0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor 0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor 0x03 (Bias Default) - Set to default biasing 0x04 (Bias Disable) - All bias settings will be disabled 0x05 (Bias High Impedance) - Configure the pin as hi_z 0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where it drives the last value on a tristate bus 0x07 (Drive Open Drain) - Configure the pin into open drain state 0x08 (Drive Open Source) - Configure the pin into open source state 0x09 (Drive Push Pull) - Configure the pin into push-pull state 0x0a (Drive Strength) - How much the pin can supply current 0x0b (Slew Rate) - Configure slew rate of the pin 0x0c (Input Debounce) - Enable input debouncer for the pin 0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin 0x0e - 0x7f - Reserved 0x80 - 0xff - Vendor defined types The PinConfigValue depends on the type and is expressed as units suitable for that type (for example bias uses Ohms). Link: https://github.com/acpica/acpica/commit/a06fdba6 Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-05 16:39:19 +08:00
u8 pin_config_type;
u32 pin_config_value;
u16 pin_table_length;
u16 vendor_length;
struct acpi_resource_source resource_source;
u16 *pin_table;
u8 *vendor_data;
};
/* Values for pin_config_type field above */
#define ACPI_PIN_CONFIG_DEFAULT 0
#define ACPI_PIN_CONFIG_BIAS_PULL_UP 1
#define ACPI_PIN_CONFIG_BIAS_PULL_DOWN 2
#define ACPI_PIN_CONFIG_BIAS_DEFAULT 3
#define ACPI_PIN_CONFIG_BIAS_DISABLE 4
#define ACPI_PIN_CONFIG_BIAS_HIGH_IMPEDANCE 5
#define ACPI_PIN_CONFIG_BIAS_BUS_HOLD 6
#define ACPI_PIN_CONFIG_DRIVE_OPEN_DRAIN 7
#define ACPI_PIN_CONFIG_DRIVE_OPEN_SOURCE 8
#define ACPI_PIN_CONFIG_DRIVE_PUSH_PULL 9
#define ACPI_PIN_CONFIG_DRIVE_STRENGTH 10
#define ACPI_PIN_CONFIG_SLEW_RATE 11
#define ACPI_PIN_CONFIG_INPUT_DEBOUNCE 12
#define ACPI_PIN_CONFIG_INPUT_SCHMITT_TRIGGER 13
struct acpi_resource_pin_group {
u8 revision_id;
u8 producer_consumer; /* For values, see Producer/Consumer above */
u16 pin_table_length;
u16 vendor_length;
u16 *pin_table;
struct acpi_resource_label resource_label;
u8 *vendor_data;
};
struct acpi_resource_pin_group_function {
u8 revision_id;
u8 producer_consumer; /* For values, see Producer/Consumer above */
u8 shareable; /* For values, see Interrupt Attributes above */
u16 function_number;
u16 vendor_length;
struct acpi_resource_source resource_source;
struct acpi_resource_label resource_source_label;
u8 *vendor_data;
};
struct acpi_resource_pin_group_config {
u8 revision_id;
u8 producer_consumer; /* For values, see Producer/Consumer above */
u8 shareable; /* For values, see Interrupt Attributes above */
u8 pin_config_type; /* For values, see pin_config_type above */
u32 pin_config_value;
u16 vendor_length;
struct acpi_resource_source resource_source;
struct acpi_resource_label resource_source_label;
u8 *vendor_data;
};
/* ACPI_RESOURCE_TYPEs */
#define ACPI_RESOURCE_TYPE_IRQ 0
#define ACPI_RESOURCE_TYPE_DMA 1
#define ACPI_RESOURCE_TYPE_START_DEPENDENT 2
#define ACPI_RESOURCE_TYPE_END_DEPENDENT 3
#define ACPI_RESOURCE_TYPE_IO 4
#define ACPI_RESOURCE_TYPE_FIXED_IO 5
#define ACPI_RESOURCE_TYPE_VENDOR 6
#define ACPI_RESOURCE_TYPE_END_TAG 7
#define ACPI_RESOURCE_TYPE_MEMORY24 8
#define ACPI_RESOURCE_TYPE_MEMORY32 9
#define ACPI_RESOURCE_TYPE_FIXED_MEMORY32 10
#define ACPI_RESOURCE_TYPE_ADDRESS16 11
#define ACPI_RESOURCE_TYPE_ADDRESS32 12
#define ACPI_RESOURCE_TYPE_ADDRESS64 13
#define ACPI_RESOURCE_TYPE_EXTENDED_ADDRESS64 14 /* ACPI 3.0 */
#define ACPI_RESOURCE_TYPE_EXTENDED_IRQ 15
#define ACPI_RESOURCE_TYPE_GENERIC_REGISTER 16
#define ACPI_RESOURCE_TYPE_GPIO 17 /* ACPI 5.0 */
#define ACPI_RESOURCE_TYPE_FIXED_DMA 18 /* ACPI 5.0 */
#define ACPI_RESOURCE_TYPE_SERIAL_BUS 19 /* ACPI 5.0 */
#define ACPI_RESOURCE_TYPE_PIN_FUNCTION 20 /* ACPI 6.2 */
ACPICA: ACPI 6.2: Add support for PinConfig() resource ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906 ACPI 6.2 introduced a new resource that is used to specify fine-grained configuration of a pin or set of pins used by a device. The ASL syntax of this new resource looks like: PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue, ResourceSource, ResourceSourceIndex, ResourceUsage, DescriptorName, Vendordata) {Pin List} PinConfigType is an integer with following accepted values: 0x00 (Default) - No configuration is applied to the pin 0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor 0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor 0x03 (Bias Default) - Set to default biasing 0x04 (Bias Disable) - All bias settings will be disabled 0x05 (Bias High Impedance) - Configure the pin as hi_z 0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where it drives the last value on a tristate bus 0x07 (Drive Open Drain) - Configure the pin into open drain state 0x08 (Drive Open Source) - Configure the pin into open source state 0x09 (Drive Push Pull) - Configure the pin into push-pull state 0x0a (Drive Strength) - How much the pin can supply current 0x0b (Slew Rate) - Configure slew rate of the pin 0x0c (Input Debounce) - Enable input debouncer for the pin 0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin 0x0e - 0x7f - Reserved 0x80 - 0xff - Vendor defined types The PinConfigValue depends on the type and is expressed as units suitable for that type (for example bias uses Ohms). Link: https://github.com/acpica/acpica/commit/a06fdba6 Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-05 16:39:19 +08:00
#define ACPI_RESOURCE_TYPE_PIN_CONFIG 21 /* ACPI 6.2 */
#define ACPI_RESOURCE_TYPE_PIN_GROUP 22 /* ACPI 6.2 */
#define ACPI_RESOURCE_TYPE_PIN_GROUP_FUNCTION 23 /* ACPI 6.2 */
#define ACPI_RESOURCE_TYPE_PIN_GROUP_CONFIG 24 /* ACPI 6.2 */
#define ACPI_RESOURCE_TYPE_MAX 24
/* Master union for resource descriptors */
union acpi_resource_data {
struct acpi_resource_irq irq;
struct acpi_resource_dma dma;
struct acpi_resource_start_dependent start_dpf;
struct acpi_resource_io io;
struct acpi_resource_fixed_io fixed_io;
struct acpi_resource_fixed_dma fixed_dma;
struct acpi_resource_vendor vendor;
struct acpi_resource_vendor_typed vendor_typed;
struct acpi_resource_end_tag end_tag;
struct acpi_resource_memory24 memory24;
struct acpi_resource_memory32 memory32;
struct acpi_resource_fixed_memory32 fixed_memory32;
struct acpi_resource_address16 address16;
struct acpi_resource_address32 address32;
struct acpi_resource_address64 address64;
struct acpi_resource_extended_address64 ext_address64;
struct acpi_resource_extended_irq extended_irq;
struct acpi_resource_generic_register generic_reg;
struct acpi_resource_gpio gpio;
struct acpi_resource_i2c_serialbus i2c_serial_bus;
struct acpi_resource_spi_serialbus spi_serial_bus;
struct acpi_resource_uart_serialbus uart_serial_bus;
struct acpi_resource_common_serialbus common_serial_bus;
struct acpi_resource_pin_function pin_function;
ACPICA: ACPI 6.2: Add support for PinConfig() resource ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906 ACPI 6.2 introduced a new resource that is used to specify fine-grained configuration of a pin or set of pins used by a device. The ASL syntax of this new resource looks like: PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue, ResourceSource, ResourceSourceIndex, ResourceUsage, DescriptorName, Vendordata) {Pin List} PinConfigType is an integer with following accepted values: 0x00 (Default) - No configuration is applied to the pin 0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor 0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor 0x03 (Bias Default) - Set to default biasing 0x04 (Bias Disable) - All bias settings will be disabled 0x05 (Bias High Impedance) - Configure the pin as hi_z 0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where it drives the last value on a tristate bus 0x07 (Drive Open Drain) - Configure the pin into open drain state 0x08 (Drive Open Source) - Configure the pin into open source state 0x09 (Drive Push Pull) - Configure the pin into push-pull state 0x0a (Drive Strength) - How much the pin can supply current 0x0b (Slew Rate) - Configure slew rate of the pin 0x0c (Input Debounce) - Enable input debouncer for the pin 0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin 0x0e - 0x7f - Reserved 0x80 - 0xff - Vendor defined types The PinConfigValue depends on the type and is expressed as units suitable for that type (for example bias uses Ohms). Link: https://github.com/acpica/acpica/commit/a06fdba6 Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-05 16:39:19 +08:00
struct acpi_resource_pin_config pin_config;
struct acpi_resource_pin_group pin_group;
struct acpi_resource_pin_group_function pin_group_function;
struct acpi_resource_pin_group_config pin_group_config;
/* Common fields */
struct acpi_resource_address address; /* Common 16/32/64 address fields */
};
/* Common resource header */
struct acpi_resource {
u32 type;
u32 length;
union acpi_resource_data data;
};
/* restore default alignment */
#pragma pack()
#define ACPI_RS_SIZE_NO_DATA 8 /* Id + Length fields */
#define ACPI_RS_SIZE_MIN (u32) ACPI_ROUND_UP_TO_NATIVE_WORD (12)
#define ACPI_RS_SIZE(type) (u32) (ACPI_RS_SIZE_NO_DATA + sizeof (type))
/* Macro for walking resource templates with multiple descriptors */
#define ACPI_NEXT_RESOURCE(res) \
ACPI_ADD_PTR (struct acpi_resource, (res), (res)->length)
struct acpi_pci_routing_table {
u32 length;
u32 pin;
u64 address; /* here for 64-bit alignment */
u32 source_index;
char source[4]; /* pad to 64 bits so sizeof() works in all cases */
};
#endif /* __ACRESTYP_H__ */