forked from luck/tmp_suning_uos_patched
406 lines
13 KiB
C
406 lines
13 KiB
C
|
/*
|
||
|
|
* drivers/tc/zs.h: Definitions for the DECstation Z85C30 serial driver.
|
||
|
|
*
|
||
|
|
* Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
|
||
|
|
* Adapted from drivers/macintosh/macserial.h by Harald Koerfgen.
|
||
|
|
*
|
||
|
|
* Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
|
||
|
|
* Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
|
||
|
|
* Copyright (C) 2004 Maciej W. Rozycki
|
||
|
|
*/
|
||
|
|
#ifndef _DECSERIAL_H
|
||
|
|
#define _DECSERIAL_H
|
||
|
|
|
||
|
|
#include <asm/dec/serial.h>
|
||
|
|
|
||
|
|
#define NUM_ZSREGS 16
|
||
|
|
|
||
|
|
struct serial_struct {
|
||
|
|
int type;
|
||
|
|
int line;
|
||
|
|
int port;
|
||
|
|
int irq;
|
||
|
|
int flags;
|
||
|
|
int xmit_fifo_size;
|
||
|
|
int custom_divisor;
|
||
|
|
int baud_base;
|
||
|
|
unsigned short close_delay;
|
||
|
|
char reserved_char[2];
|
||
|
|
int hub6;
|
||
|
|
unsigned short closing_wait; /* time to wait before closing */
|
||
|
|
unsigned short closing_wait2; /* no longer used... */
|
||
|
|
int reserved[4];
|
||
|
|
};
|
||
|
|
|
||
|
|
/*
|
||
|
|
* For the close wait times, 0 means wait forever for serial port to
|
||
|
|
* flush its output. 65535 means don't wait at all.
|
||
|
|
*/
|
||
|
|
#define ZILOG_CLOSING_WAIT_INF 0
|
||
|
|
#define ZILOG_CLOSING_WAIT_NONE 65535
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Definitions for ZILOG_struct (and serial_struct) flags field
|
||
|
|
*/
|
||
|
|
#define ZILOG_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes
|
||
|
|
on the callout port */
|
||
|
|
#define ZILOG_FOURPORT 0x0002 /* Set OU1, OUT2 per AST Fourport settings */
|
||
|
|
#define ZILOG_SAK 0x0004 /* Secure Attention Key (Orange book) */
|
||
|
|
#define ZILOG_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */
|
||
|
|
|
||
|
|
#define ZILOG_SPD_MASK 0x0030
|
||
|
|
#define ZILOG_SPD_HI 0x0010 /* Use 56000 instead of 38400 bps */
|
||
|
|
|
||
|
|
#define ZILOG_SPD_VHI 0x0020 /* Use 115200 instead of 38400 bps */
|
||
|
|
#define ZILOG_SPD_CUST 0x0030 /* Use user-specified divisor */
|
||
|
|
|
||
|
|
#define ZILOG_SKIP_TEST 0x0040 /* Skip UART test during autoconfiguration */
|
||
|
|
#define ZILOG_AUTO_IRQ 0x0080 /* Do automatic IRQ during autoconfiguration */
|
||
|
|
#define ZILOG_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */
|
||
|
|
#define ZILOG_PGRP_LOCKOUT 0x0200 /* Lock out cua opens based on pgrp */
|
||
|
|
#define ZILOG_CALLOUT_NOHUP 0x0400 /* Don't do hangups for cua device */
|
||
|
|
|
||
|
|
#define ZILOG_FLAGS 0x0FFF /* Possible legal ZILOG flags */
|
||
|
|
#define ZILOG_USR_MASK 0x0430 /* Legal flags that non-privileged
|
||
|
|
* users can set or reset */
|
||
|
|
|
||
|
|
/* Internal flags used only by kernel/chr_drv/serial.c */
|
||
|
|
#define ZILOG_INITIALIZED 0x80000000 /* Serial port was initialized */
|
||
|
|
#define ZILOG_CALLOUT_ACTIVE 0x40000000 /* Call out device is active */
|
||
|
|
#define ZILOG_NORMAL_ACTIVE 0x20000000 /* Normal device is active */
|
||
|
|
#define ZILOG_BOOT_AUTOCONF 0x10000000 /* Autoconfigure port on bootup */
|
||
|
|
#define ZILOG_CLOSING 0x08000000 /* Serial port is closing */
|
||
|
|
#define ZILOG_CTS_FLOW 0x04000000 /* Do CTS flow control */
|
||
|
|
#define ZILOG_CHECK_CD 0x02000000 /* i.e., CLOCAL */
|
||
|
|
|
||
|
|
/* Software state per channel */
|
||
|
|
|
||
|
|
#ifdef __KERNEL__
|
||
|
|
/*
|
||
|
|
* This is our internal structure for each serial port's state.
|
||
|
|
*
|
||
|
|
* Many fields are paralleled by the structure used by the serial_struct
|
||
|
|
* structure.
|
||
|
|
*
|
||
|
|
* For definitions of the flags field, see tty.h
|
||
|
|
*/
|
||
|
|
|
||
|
|
struct dec_zschannel {
|
||
|
|
volatile unsigned char *control;
|
||
|
|
volatile unsigned char *data;
|
||
|
|
|
||
|
|
/* Current write register values */
|
||
|
|
unsigned char curregs[NUM_ZSREGS];
|
||
|
|
};
|
||
|
|
|
||
|
|
struct dec_serial {
|
||
|
|
struct dec_serial *zs_next; /* For IRQ servicing chain. */
|
||
|
|
struct dec_zschannel *zs_channel; /* Channel registers. */
|
||
|
|
struct dec_zschannel *zs_chan_a; /* A side registers. */
|
||
|
|
unsigned char read_reg_zero;
|
||
|
|
|
||
|
|
struct dec_serial_hook *hook; /* Hook on this channel. */
|
||
|
|
int tty_break; /* Set on BREAK condition. */
|
||
|
|
int is_cons; /* Is this our console. */
|
||
|
|
int tx_active; /* Char is being xmitted. */
|
||
|
|
int tx_stopped; /* Output is suspended. */
|
||
|
|
|
||
|
|
/*
|
||
|
|
* We need to know the current clock divisor
|
||
|
|
* to read the bps rate the chip has currently loaded.
|
||
|
|
*/
|
||
|
|
int clk_divisor; /* May be 1, 16, 32, or 64. */
|
||
|
|
int zs_baud;
|
||
|
|
|
||
|
|
char change_needed;
|
||
|
|
|
||
|
|
int magic;
|
||
|
|
int baud_base;
|
||
|
|
int port;
|
||
|
|
int irq;
|
||
|
|
int flags; /* Defined in tty.h. */
|
||
|
|
int type; /* UART type. */
|
||
|
|
struct tty_struct *tty;
|
||
|
|
int read_status_mask;
|
||
|
|
int ignore_status_mask;
|
||
|
|
int timeout;
|
||
|
|
int xmit_fifo_size;
|
||
|
|
int custom_divisor;
|
||
|
|
int x_char; /* XON/XOFF character. */
|
||
|
|
int close_delay;
|
||
|
|
unsigned short closing_wait;
|
||
|
|
unsigned short closing_wait2;
|
||
|
|
unsigned long event;
|
||
|
|
unsigned long last_active;
|
||
|
|
int line;
|
||
|
|
int count; /* # of fds on device. */
|
||
|
|
int blocked_open; /* # of blocked opens. */
|
||
|
|
unsigned char *xmit_buf;
|
||
|
|
int xmit_head;
|
||
|
|
int xmit_tail;
|
||
|
|
int xmit_cnt;
|
||
|
|
struct tq_struct tqueue;
|
||
|
|
struct tq_struct tqueue_hangup;
|
||
|
|
wait_queue_head_t open_wait;
|
||
|
|
wait_queue_head_t close_wait;
|
||
|
|
};
|
||
|
|
|
||
|
|
|
||
|
|
#define SERIAL_MAGIC 0x5301
|
||
|
|
|
||
|
|
/*
|
||
|
|
* The size of the serial xmit buffer is 1 page, or 4096 bytes
|
||
|
|
*/
|
||
|
|
#define SERIAL_XMIT_SIZE 4096
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Events are used to schedule things to happen at timer-interrupt
|
||
|
|
* time, instead of at rs interrupt time.
|
||
|
|
*/
|
||
|
|
#define RS_EVENT_WRITE_WAKEUP 0
|
||
|
|
|
||
|
|
#endif /* __KERNEL__ */
|
||
|
|
|
||
|
|
/* Conversion routines to/from brg time constants from/to bits
|
||
|
|
* per second.
|
||
|
|
*/
|
||
|
|
#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
|
||
|
|
#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
|
||
|
|
|
||
|
|
/* The Zilog register set */
|
||
|
|
|
||
|
|
#define FLAG 0x7e
|
||
|
|
|
||
|
|
/* Write Register 0 */
|
||
|
|
#define R0 0 /* Register selects */
|
||
|
|
#define R1 1
|
||
|
|
#define R2 2
|
||
|
|
#define R3 3
|
||
|
|
#define R4 4
|
||
|
|
#define R5 5
|
||
|
|
#define R6 6
|
||
|
|
#define R7 7
|
||
|
|
#define R8 8
|
||
|
|
#define R9 9
|
||
|
|
#define R10 10
|
||
|
|
#define R11 11
|
||
|
|
#define R12 12
|
||
|
|
#define R13 13
|
||
|
|
#define R14 14
|
||
|
|
#define R15 15
|
||
|
|
|
||
|
|
#define NULLCODE 0 /* Null Code */
|
||
|
|
#define POINT_HIGH 0x8 /* Select upper half of registers */
|
||
|
|
#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
|
||
|
|
#define SEND_ABORT 0x18 /* HDLC Abort */
|
||
|
|
#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
|
||
|
|
#define RES_Tx_P 0x28 /* Reset TxINT Pending */
|
||
|
|
#define ERR_RES 0x30 /* Error Reset */
|
||
|
|
#define RES_H_IUS 0x38 /* Reset highest IUS */
|
||
|
|
|
||
|
|
#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
|
||
|
|
#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
|
||
|
|
#define RES_EOM_L 0xC0 /* Reset EOM latch */
|
||
|
|
|
||
|
|
/* Write Register 1 */
|
||
|
|
|
||
|
|
#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
|
||
|
|
#define TxINT_ENAB 0x2 /* Tx Int Enable */
|
||
|
|
#define PAR_SPEC 0x4 /* Parity is special condition */
|
||
|
|
|
||
|
|
#define RxINT_DISAB 0 /* Rx Int Disable */
|
||
|
|
#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
|
||
|
|
#define RxINT_ALL 0x10 /* Int on all Rx Characters or error */
|
||
|
|
#define RxINT_ERR 0x18 /* Int on error only */
|
||
|
|
#define RxINT_MASK 0x18
|
||
|
|
|
||
|
|
#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
|
||
|
|
#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
|
||
|
|
#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
|
||
|
|
|
||
|
|
/* Write Register #2 (Interrupt Vector) */
|
||
|
|
|
||
|
|
/* Write Register 3 */
|
||
|
|
|
||
|
|
#define RxENABLE 0x1 /* Rx Enable */
|
||
|
|
#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
|
||
|
|
#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
|
||
|
|
#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
|
||
|
|
#define ENT_HM 0x10 /* Enter Hunt Mode */
|
||
|
|
#define AUTO_ENAB 0x20 /* Auto Enables */
|
||
|
|
#define Rx5 0x0 /* Rx 5 Bits/Character */
|
||
|
|
#define Rx7 0x40 /* Rx 7 Bits/Character */
|
||
|
|
#define Rx6 0x80 /* Rx 6 Bits/Character */
|
||
|
|
#define Rx8 0xc0 /* Rx 8 Bits/Character */
|
||
|
|
#define RxNBITS_MASK 0xc0
|
||
|
|
|
||
|
|
/* Write Register 4 */
|
||
|
|
|
||
|
|
#define PAR_ENA 0x1 /* Parity Enable */
|
||
|
|
#define PAR_EVEN 0x2 /* Parity Even/Odd* */
|
||
|
|
|
||
|
|
#define SYNC_ENAB 0 /* Sync Modes Enable */
|
||
|
|
#define SB1 0x4 /* 1 stop bit/char */
|
||
|
|
#define SB15 0x8 /* 1.5 stop bits/char */
|
||
|
|
#define SB2 0xc /* 2 stop bits/char */
|
||
|
|
#define SB_MASK 0xc
|
||
|
|
|
||
|
|
#define MONSYNC 0 /* 8 Bit Sync character */
|
||
|
|
#define BISYNC 0x10 /* 16 bit sync character */
|
||
|
|
#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
|
||
|
|
#define EXTSYNC 0x30 /* External Sync Mode */
|
||
|
|
|
||
|
|
#define X1CLK 0x0 /* x1 clock mode */
|
||
|
|
#define X16CLK 0x40 /* x16 clock mode */
|
||
|
|
#define X32CLK 0x80 /* x32 clock mode */
|
||
|
|
#define X64CLK 0xC0 /* x64 clock mode */
|
||
|
|
#define XCLK_MASK 0xC0
|
||
|
|
|
||
|
|
/* Write Register 5 */
|
||
|
|
|
||
|
|
#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
|
||
|
|
#define RTS 0x2 /* RTS */
|
||
|
|
#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
|
||
|
|
#define TxENAB 0x8 /* Tx Enable */
|
||
|
|
#define SND_BRK 0x10 /* Send Break */
|
||
|
|
#define Tx5 0x0 /* Tx 5 bits (or less)/character */
|
||
|
|
#define Tx7 0x20 /* Tx 7 bits/character */
|
||
|
|
#define Tx6 0x40 /* Tx 6 bits/character */
|
||
|
|
#define Tx8 0x60 /* Tx 8 bits/character */
|
||
|
|
#define TxNBITS_MASK 0x60
|
||
|
|
#define DTR 0x80 /* DTR */
|
||
|
|
|
||
|
|
/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
|
||
|
|
|
||
|
|
/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
|
||
|
|
|
||
|
|
/* Write Register 8 (transmit buffer) */
|
||
|
|
|
||
|
|
/* Write Register 9 (Master interrupt control) */
|
||
|
|
#define VIS 1 /* Vector Includes Status */
|
||
|
|
#define NV 2 /* No Vector */
|
||
|
|
#define DLC 4 /* Disable Lower Chain */
|
||
|
|
#define MIE 8 /* Master Interrupt Enable */
|
||
|
|
#define STATHI 0x10 /* Status high */
|
||
|
|
#define SOFTACK 0x20 /* Software Interrupt Acknowledge */
|
||
|
|
#define NORESET 0 /* No reset on write to R9 */
|
||
|
|
#define CHRB 0x40 /* Reset channel B */
|
||
|
|
#define CHRA 0x80 /* Reset channel A */
|
||
|
|
#define FHWRES 0xc0 /* Force hardware reset */
|
||
|
|
|
||
|
|
/* Write Register 10 (misc control bits) */
|
||
|
|
#define BIT6 1 /* 6 bit/8bit sync */
|
||
|
|
#define LOOPMODE 2 /* SDLC Loop mode */
|
||
|
|
#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
|
||
|
|
#define MARKIDLE 8 /* Mark/flag on idle */
|
||
|
|
#define GAOP 0x10 /* Go active on poll */
|
||
|
|
#define NRZ 0 /* NRZ mode */
|
||
|
|
#define NRZI 0x20 /* NRZI mode */
|
||
|
|
#define FM1 0x40 /* FM1 (transition = 1) */
|
||
|
|
#define FM0 0x60 /* FM0 (transition = 0) */
|
||
|
|
#define CRCPS 0x80 /* CRC Preset I/O */
|
||
|
|
|
||
|
|
/* Write Register 11 (Clock Mode control) */
|
||
|
|
#define TRxCXT 0 /* TRxC = Xtal output */
|
||
|
|
#define TRxCTC 1 /* TRxC = Transmit clock */
|
||
|
|
#define TRxCBR 2 /* TRxC = BR Generator Output */
|
||
|
|
#define TRxCDP 3 /* TRxC = DPLL output */
|
||
|
|
#define TRxCOI 4 /* TRxC O/I */
|
||
|
|
#define TCRTxCP 0 /* Transmit clock = RTxC pin */
|
||
|
|
#define TCTRxCP 8 /* Transmit clock = TRxC pin */
|
||
|
|
#define TCBR 0x10 /* Transmit clock = BR Generator output */
|
||
|
|
#define TCDPLL 0x18 /* Transmit clock = DPLL output */
|
||
|
|
#define RCRTxCP 0 /* Receive clock = RTxC pin */
|
||
|
|
#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
|
||
|
|
#define RCBR 0x40 /* Receive clock = BR Generator output */
|
||
|
|
#define RCDPLL 0x60 /* Receive clock = DPLL output */
|
||
|
|
#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
|
||
|
|
|
||
|
|
/* Write Register 12 (lower byte of baud rate generator time constant) */
|
||
|
|
|
||
|
|
/* Write Register 13 (upper byte of baud rate generator time constant) */
|
||
|
|
|
||
|
|
/* Write Register 14 (Misc control bits) */
|
||
|
|
#define BRENABL 1 /* Baud rate generator enable */
|
||
|
|
#define BRSRC 2 /* Baud rate generator source */
|
||
|
|
#define DTRREQ 4 /* DTR/Request function */
|
||
|
|
#define AUTOECHO 8 /* Auto Echo */
|
||
|
|
#define LOOPBAK 0x10 /* Local loopback */
|
||
|
|
#define SEARCH 0x20 /* Enter search mode */
|
||
|
|
#define RMC 0x40 /* Reset missing clock */
|
||
|
|
#define DISDPLL 0x60 /* Disable DPLL */
|
||
|
|
#define SSBR 0x80 /* Set DPLL source = BR generator */
|
||
|
|
#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
|
||
|
|
#define SFMM 0xc0 /* Set FM mode */
|
||
|
|
#define SNRZI 0xe0 /* Set NRZI mode */
|
||
|
|
|
||
|
|
/* Write Register 15 (external/status interrupt control) */
|
||
|
|
#define ZCIE 2 /* Zero count IE */
|
||
|
|
#define DCDIE 8 /* DCD IE */
|
||
|
|
#define SYNCIE 0x10 /* Sync/hunt IE */
|
||
|
|
#define CTSIE 0x20 /* CTS IE */
|
||
|
|
#define TxUIE 0x40 /* Tx Underrun/EOM IE */
|
||
|
|
#define BRKIE 0x80 /* Break/Abort IE */
|
||
|
|
|
||
|
|
|
||
|
|
/* Read Register 0 */
|
||
|
|
#define Rx_CH_AV 0x1 /* Rx Character Available */
|
||
|
|
#define ZCOUNT 0x2 /* Zero count */
|
||
|
|
#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
|
||
|
|
#define DCD 0x8 /* DCD */
|
||
|
|
#define SYNC_HUNT 0x10 /* Sync/hunt */
|
||
|
|
#define CTS 0x20 /* CTS */
|
||
|
|
#define TxEOM 0x40 /* Tx underrun */
|
||
|
|
#define BRK_ABRT 0x80 /* Break/Abort */
|
||
|
|
|
||
|
|
/* Read Register 1 */
|
||
|
|
#define ALL_SNT 0x1 /* All sent */
|
||
|
|
/* Residue Data for 8 Rx bits/char programmed */
|
||
|
|
#define RES3 0x8 /* 0/3 */
|
||
|
|
#define RES4 0x4 /* 0/4 */
|
||
|
|
#define RES5 0xc /* 0/5 */
|
||
|
|
#define RES6 0x2 /* 0/6 */
|
||
|
|
#define RES7 0xa /* 0/7 */
|
||
|
|
#define RES8 0x6 /* 0/8 */
|
||
|
|
#define RES18 0xe /* 1/8 */
|
||
|
|
#define RES28 0x0 /* 2/8 */
|
||
|
|
/* Special Rx Condition Interrupts */
|
||
|
|
#define PAR_ERR 0x10 /* Parity error */
|
||
|
|
#define Rx_OVR 0x20 /* Rx Overrun Error */
|
||
|
|
#define FRM_ERR 0x40 /* CRC/Framing Error */
|
||
|
|
#define END_FR 0x80 /* End of Frame (SDLC) */
|
||
|
|
|
||
|
|
/* Read Register 2 (channel b only) - Interrupt vector */
|
||
|
|
|
||
|
|
/* Read Register 3 (interrupt pending register) ch a only */
|
||
|
|
#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
|
||
|
|
#define CHBTxIP 0x2 /* Channel B Tx IP */
|
||
|
|
#define CHBRxIP 0x4 /* Channel B Rx IP */
|
||
|
|
#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
|
||
|
|
#define CHATxIP 0x10 /* Channel A Tx IP */
|
||
|
|
#define CHARxIP 0x20 /* Channel A Rx IP */
|
||
|
|
|
||
|
|
/* Read Register 8 (receive data register) */
|
||
|
|
|
||
|
|
/* Read Register 10 (misc status bits) */
|
||
|
|
#define ONLOOP 2 /* On loop */
|
||
|
|
#define LOOPSEND 0x10 /* Loop sending */
|
||
|
|
#define CLK2MIS 0x40 /* Two clocks missing */
|
||
|
|
#define CLK1MIS 0x80 /* One clock missing */
|
||
|
|
|
||
|
|
/* Read Register 12 (lower byte of baud rate generator constant) */
|
||
|
|
|
||
|
|
/* Read Register 13 (upper byte of baud rate generator constant) */
|
||
|
|
|
||
|
|
/* Read Register 15 (value of WR 15) */
|
||
|
|
|
||
|
|
/* Misc macros */
|
||
|
|
#define ZS_CLEARERR(channel) (write_zsreg(channel, 0, ERR_RES))
|
||
|
|
#define ZS_CLEARFIFO(channel) do { volatile unsigned char garbage; \
|
||
|
|
garbage = read_zsdata(channel); \
|
||
|
|
garbage = read_zsdata(channel); \
|
||
|
|
garbage = read_zsdata(channel); \
|
||
|
|
} while(0)
|
||
|
|
|
||
|
|
#endif /* !(_DECSERIAL_H) */
|