forked from luck/tmp_suning_uos_patched
Blackfin SPI Driver: fix bug - correct usage of struct spi_transfer.cs_change
According to comments in linux/spi/spi.h: * All SPI transfers start with the relevant chipselect active. Normally * it stays selected until after the last transfer in a message. Drivers * can affect the chipselect signal using cs_change. * * (i) If the transfer isn't the last one in the message, this flag is * used to make the chipselect briefly go inactive in the middle of the * message. Toggling chipselect in this way may be needed to terminate * a chip command, letting a single spi_message perform all of group of * chip transactions together. * * (ii) When the transfer is the last one in the message, the chip may * stay selected until the next transfer. On multi-device SPI busses * with nothing blocking messages going to other devices, this is just * a performance hint; starting a message to another device deselects * this one. But in other cases, this can be used to ensure correctness. * Some devices need protocol transactions to be built from a series of * spi_message submissions, where the content of one message is determined * by the results of previous messages and where the whole transaction * ends when the chipselect goes intactive. Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit is contained in:
parent
2cf3683472
commit
b9b2a76a43
@ -540,15 +540,13 @@ static void giveback(struct driver_data *drv_data)
|
||||
|
||||
msg->state = NULL;
|
||||
|
||||
/* disable chip select signal. And not stop spi in autobuffer mode */
|
||||
if (drv_data->tx_dma != 0xFFFF) {
|
||||
cs_deactive(drv_data, chip);
|
||||
bfin_spi_disable(drv_data);
|
||||
}
|
||||
|
||||
if (!drv_data->cs_change)
|
||||
cs_deactive(drv_data, chip);
|
||||
|
||||
/* Not stop spi in autobuffer mode */
|
||||
if (drv_data->tx_dma != 0xFFFF)
|
||||
bfin_spi_disable(drv_data);
|
||||
|
||||
if (msg->complete)
|
||||
msg->complete(msg->context);
|
||||
}
|
||||
@ -757,7 +755,8 @@ static void pump_transfers(unsigned long data)
|
||||
|
||||
write_STAT(drv_data, BIT_STAT_CLR);
|
||||
cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD));
|
||||
cs_active(drv_data, chip);
|
||||
if (drv_data->cs_change)
|
||||
cs_active(drv_data, chip);
|
||||
|
||||
dev_dbg(&drv_data->pdev->dev,
|
||||
"now pumping a transfer: width is %d, len is %d\n",
|
||||
@ -919,11 +918,11 @@ static void pump_transfers(unsigned long data)
|
||||
} else {
|
||||
/* Update total byte transfered */
|
||||
message->actual_length += drv_data->len_in_bytes;
|
||||
|
||||
/* Move to next transfer of this msg */
|
||||
message->state = next_transfer(drv_data);
|
||||
if (drv_data->cs_change)
|
||||
cs_deactive(drv_data, chip);
|
||||
}
|
||||
|
||||
/* Schedule next transfer tasklet */
|
||||
tasklet_schedule(&drv_data->pump_transfers);
|
||||
|
||||
|
Loading…
Reference in New Issue
Block a user