In some cases, multiple OFDT nodes might share the same location code, so
the location code is not a unique identifier for an OFDT node. Changed the
ibmebus probe/remove interface to use the DT path of the device node instead
of the location code.
The DT path must be written into probe/remove right as it would appear in
the "devspec" attribute of the ebus device: relative to the DT root, with a
leading slash and without a trailing slash. One trailing newline will not
hurt; multiple newlines will (like perl's chomp()).
Example:
Add a device "/proc/device-tree/foo@12345678" to ibmebus like this:
echo /foo@12345678 > /sys/bus/ibmebus/probe
Remove the device like this:
echo /foo@12345678 > /sys/bus/ibmebus/remove
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's an implementation of DEBUG_PAGEALLOC for 64 bits powerpc.
It applies on top of the 32 bits patch.
Unlike Anton's previous attempt, I'm not using updatepp. I'm removing
the hash entries from the bolted mapping (using a map in RAM of all the
slots). Expensive but it doesn't really matter, does it ? :-)
Memory hot-added doesn't benefit from this unless it's added at an
address that is below end_of_DRAM() as calculated at boot time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/Kconfig.debug | 2
arch/powerpc/mm/hash_utils_64.c | 84 ++++++++++++++++++++++++++++++++++++++--
2 files changed, 82 insertions(+), 4 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's an implementation of DEBUG_PAGEALLOC for ppc32. It disables BAT
mapping and is only tested with Hash table based processor though it
shouldn't be too hard to adapt it to others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/Kconfig.debug | 9 ++++++
arch/powerpc/mm/init_32.c | 4 +++
arch/powerpc/mm/pgtable_32.c | 52 +++++++++++++++++++++++++++++++++++++++
arch/powerpc/mm/ppc_mmu_32.c | 4 ++-
include/asm-powerpc/cacheflush.h | 6 ++++
5 files changed, 74 insertions(+), 1 deletion(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
On hash table based 32 bits powerpc's, the hash management code runs with
a big spinlock. It's thus important that it never causes itself a hash
fault. That code is generally safe (it does memory accesses in real mode
among other things) with the exception of the actual access to the code
itself. That is, the kernel text needs to be accessible without taking
a hash miss exceptions.
This is currently guaranteed by having a BAT register mapping part of the
linear mapping permanently, which includes the kernel text. But this is
not true if using the "nobats" kernel command line option (which can be
useful for debugging) and will not be true when using DEBUG_PAGEALLOC
implemented in a subsequent patch.
This patch fixes this by pre-faulting in the hash table pages that hit
the kernel text, and making sure we never evict such a page under hash
pressure.
Signed-off-by: Benjamin Herrenchmidt <benh@kernel.crashing.org>
arch/powerpc/mm/hash_low_32.S | 22 ++++++++++++++++++++--
arch/powerpc/mm/mem.c | 3 ---
arch/powerpc/mm/mmu_decl.h | 4 ++++
arch/powerpc/mm/pgtable_32.c | 11 +++++++----
4 files changed, 31 insertions(+), 9 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits map_page() function is used internally by the mm code
for early mmu mappings and for ioremap. It should never be called
for an address that already has a valid PTE or hash entry, so we
add a BUG_ON for that and remove the useless flush_HPTE call.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/mm/pgtable_32.c | 9 ++++++---
1 file changed, 6 insertions(+), 3 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current tlb flush code on powerpc 64 bits has a subtle race since we
lost the page table lock due to the possible faulting in of new PTEs
after a previous one has been removed but before the corresponding hash
entry has been evicted, which can leads to all sort of fatal problems.
This patch reworks the batch code completely. It doesn't use the mmu_gather
stuff anymore. Instead, we use the lazy mmu hooks that were added by the
paravirt code. They have the nice property that the enter/leave lazy mmu
mode pair is always fully contained by the PTE lock for a given range
of PTEs. Thus we can guarantee that all batches are flushed on a given
CPU before it drops that lock.
We also generalize batching for any PTE update that require a flush.
Batching is now enabled on a CPU by arch_enter_lazy_mmu_mode() and
disabled by arch_leave_lazy_mmu_mode(). The code epects that this is
always contained within a PTE lock section so no preemption can happen
and no PTE insertion in that range from another CPU. When batching
is enabled on a CPU, every PTE updates that need a hash flush will
use the batch for that flush.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the alignment exception handler use the new _inatomic variants
of __get/put_user. This fixes erroneous warnings in the very rare
cases where we manage to have copy_tofrom_user_inatomic() trigger
an alignment exception.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/kernel/align.c | 56 ++++++++++++++++++++++++--------------------
1 file changed, 31 insertions(+), 25 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
The firmware assigns irq 20/21 to the VIA IDE device on Pegasos.
But the required interrupt is 14/15.
Maybe someone confused decimal vs. hexadecimal values.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also fixes a bug where a property value was being modified
in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers have resources that they want to be able to map into
userspace that are 4k in size. On a kernel configured with 64k pages
we currently end up mapping the 4k we want plus another 60k of
physical address space, which could contain anything. This can
introduce security problems, for example in the case of an infiniband
adaptor where the other 60k could contain registers that some other
program is using for its communications.
This patch adds a new function, remap_4k_pfn, which drivers can use to
map a single 4k page to userspace regardless of whether the kernel is
using a 4k or a 64k page size. Like remap_pfn_range, it would
typically be called in a driver's mmap function. It only maps a
single 4k page, which on a 64k page kernel appears replicated 16 times
throughout a 64k page. On a 4k page kernel it reduces to a call to
remap_pfn_range.
The way this works on a 64k kernel is that a new bit, _PAGE_4K_PFN,
gets set on the linux PTE. This alters the way that __hash_page_4K
computes the real address to put in the HPTE. The RPN field of the
linux PTE becomes the 4k RPN directly rather than being interpreted as
a 64k RPN. Since the RPN field is 32 bits, this means that physical
addresses being mapped with remap_4k_pfn have to be below 2^44,
i.e. 0x100000000000.
The patch also factors out the code in arch/powerpc/mm/hash_utils_64.c
that deals with demoting a process to use 4k pages into one function
that gets called in the various different places where we need to do
that. There were some discrepancies between exactly what was done in
the various places, such as a call to spu_flush_all_slbs in one case
but not in others.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
We add a device_is_compatible define for compatibility during the
change over.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
We add a get_property define for compatibility during the change over.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Efika boards have to be booted with console=ttyPSC0 unless there is a
graphics card plugged in. Detect if the firmware stdout is the serial
connector.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our kernels put everything in the first load segment, and we read that.
Instead of decompressing to the end of the gzip stream or supplied image
and hoping we get it all, decompress the expected size and complain if
it is not available.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit a9903811bf missed two uses of the
the .gz suffix in the wrapper script and didn't clean the additonal
possibly cached files.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
crt0.S had provisions to provide run address relocaton to got2 and
cache flush, but not on the bss clear or stack pointer load. Apply
the same fixup for them.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ELF parsing routines local to arch/powerpc/boot/main.c are useful
to other callers therefore move them to their own file.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
72486f1f8f inverted the sense for enabling
hotplug CPU controls without reference to any other architecture other than
i386, ia64 and PowerPC. This left everyone else without hotplug CPU control.
Fix powerpc for this brain damage.
(akpm: patch adapted from rmk's ARM fix. Changelog stolen from rmk)
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Lifted from http://bugzilla.kernel.org/show_bug.cgi?id=8182
Steps to reproduce:
- Boot an Ocotea board with the mainline 2.6.20.1 kernel.
- Create an /etc/ntp.conf file with at least one NTP server and iburst mode set.
- Issue the command "ntpd -g".
- Wait about two minutes.
- Verify ntpd's status via "ntpq -pn" and by looking in /var/log/ntp.
This fixes this problem by adjusting the expected clock frequency.
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dt_xlate_reg() uses the ranges properties of a node's parentage to find
the absolute physical address of the node's registers.
The ns16550 driver uses this when no virtual-reg property is found.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no reason to yield the CPU in spu_yield - if the backing
thread reenters spu_run it gets added to the end of the runqueue for
it's priority. So the yield is just a slowdown for the case where
we have higher priority contexts waiting.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I wanted to enable CBE_THERM on PS3. So I had to enable CBE_RAS first.
But the resulting kernel doesn't link, as cbe_regs.c isn't compiled for
non-PPC_CELL_NATIVE.
CBE_RAS should depend on PPC_CELL_NATIVE; this makes it so.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is now inaccurate because we may not have entered prom_init() and
r3 is overwritten immediately anyway.
Signed-off-by: Sonny Rao <sonny@burdell.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove unneeded inclusion of linux/ide.h
It does not compile with CONFIG_BLOCK=n.
Remove asm/ide.h from ksyms file, it gets included earlier via
linux/ide.h.
Compile tested with all defconfig files.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix link errors with CONFIG_EEH=n:
arch/powerpc/platforms/built-in.o: In function `.pcibios_fixup_new_pci_devices':
(.text+0x41c8): undefined reference to `.eeh_add_device_tree_late'
arch/powerpc/platforms/built-in.o: In function `.init_phb_dynamic':
(.text+0x4280): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pcibios_remove_pci_devices':
(.text+0x42fc): undefined reference to `.eeh_remove_bus_device'
arch/powerpc/platforms/built-in.o: In function `.pcibios_add_pci_devices':
(.text+0x43c0): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pSeries_final_fixup':
(.init.text+0xb4): undefined reference to `.pci_addr_cache_build'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up how the zImage code manipulates the kernel
command line. Notable improvements from the old handling:
- Command line manipulation is consolidated into a new
prep_cmdline() function, rather than being scattered across start()
and some helper functions
- Less stack space use: we use just a single global command
line buffer, which can be initialized by an external tool as before,
we no longer need another command line sized buffer on the stack.
- Easier to support platforms whose firmware passes a
commandline, but not a device tree. Platform code can now point new
loader_info fields to the firmware's command line, rather than having
to do early manipulation of the /chosen bootargs property which may
then be rewritten again by the core.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a library of useful device tree manipulation functions
to the zImage library, for use by platform code. These functions are
based on the hooks already in dt_ops, so they're not dependent on a
particular device tree implementation. This patch also slightly
streamlines the code in main.c using these new functions.
This is a consolidation of my work in this area with Scott Wood's
patches to a very similar end.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
mtocrf is a faster single-field mtcrf (move to condition register
fields) instruction available in POWER4 and later processors. It can
make quite a difference in performance on some implementations, so use
it for CONFIG_POWER4_ONLY builds.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are many adapters which cannot handle DMAing across any 4 GB
boundary. For instance, the latest Emulex adapters.
This normally is not an issue as firmware gives dma-windows under
4gigs. However, some of the new System-P boxes have dma-windows above
4gigs, and this present a problem.
During initialization of the IOMMU tables, the last entry at each 4GB
boundary is marked as used. Thus no mappings can cross the boundary.
If a table ends at a 4GB boundary, the entry is not marked as used.
A boot option to remove this 4GB protection is given w/ protect4gb=off.
This exposes the potential issue for driver and hardware development
purposes.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adding this handler allow userspace to properly handle the module
autoloading. The generation of the uevent itself is now common to
all bus using of_device, so not much code here.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This common uevent handler allow the several bus types based on
of_device to generate the uevent properly and avoiding
code duplication.
This handlers take a struct device as argument and can therefore
be used as the uevent call directly if no special treatment is
needed for the bus.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bit setting was off by one.
Tested with RTC and GPIO_WKUP interrupts.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:nvidia_bugs from .data between 'early_qrk' (at offset 0x8428) and 'enable_cpu_hotplug'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:via_bugs from .data between 'early_qrk' (at offset 0x8438) and 'enable_cpu_hotplug'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:ati_bugs from .data between 'early_qrk' (at offset 0x8448) and 'enable_cpu_hotplug'
The compiler is putting it into .data because the __initdata is in the wrong
place.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since lazy MMU batching mode still allows interrupts to enter, it is
possible for interrupt handlers to try to use kmap_atomic, which fails when
lazy mode is active, since the PTE update to highmem will be delayed. The
best workaround is to issue an explicit flush in kmap_atomic_functions
case; this is the only way nested PTE updates can happen in the interrupt
handler.
Thanks to Jeremy Fitzhardinge for noting the bug and suggestions on a fix.
This patch gets reverted again when we start 2.6.22 and the bug gets fixed
differently.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a SGI Altix TIOCP based PCI bus we need to include the ATE_PIO attribute
bit if we're mapping a 32bit MSI address.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
My patch: git commit=95235ca2c20ac0b31a8eb39e2d599bcc3e9c9a10 introduced a bug
in IA64 cpuinfo output.
Patch changed the proc_freq from 1HZ resolution to 1KHz resolution, but left
format string unchanged at " %lu.%06lu". Below is the fix.
Thanks to Bjorn for catching this.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86: Don't probe for DDC on VBE1.2
[PATCH] x86-64: Increase NMI watchdog probing timeout
[PATCH] x86-64: Let oprofile reserve MSR on all CPUs
[PATCH] x86-64: Disable local APIC timer use on AMD systems with C1E
The __copy_to_user_inatomic() calls in file_read_actor() and pipe_read()
are broken on original i386 machines, where WP-works-ok == false, as
__copy_to_user_inatomic() on such systems calls functions which might
sleep and/or contain cond_resched() calls inside of a kmap_atomic()
region.
The original check for WP-works-ok was in access_ok(), but got moved
during the 2.5 series to fix a race vs. swap.
Return the number of bytes to copy in the case where we are in an atomic
region, so the non atomic code pathes in file_read_actor() and
pipe_read() are taken.
This could be optimized to avoid the kmap_atomicby moving the check for
WP-works-ok into fault_in_pages_writeable(), but this is more intrusive
and can be done later.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the regression resulting from the recent change of suspend code
ordering that causes systems based on Intel x86 CPUs using the microcode
driver to hang during the resume.
The problem occurs since the microcode driver uses request_firmware() in
its CPU hotplug notifier, which is called after tasks has been frozen and
hangs. It can be fixed by telling the microcode driver to use the
microcode stored in memory during the resume instead of trying to load it
from disk.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Adrian Bunk <bunk@stusta.de>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maxim <maximlevitsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have a confused udelay implementation.
* __const_udelay does not accept usecs but xloops in i386 and x86_64
* our implementation requires usecs as arg
* it gets a xloops count when called by asm/arch/delay.h
Bugs related to this (extremely long shutdown times) where reported by some
x86_64 users, especially using Device Mapper.
To hit this bug, a compile-time constant time parameter must be passed -
that's why UML seems to work most times. Fix this with a simple udelay
implementation.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VBE1.2 doesn't support function 15h (DDC) resulting in a 'hang' whilst
uncompressing kernel with some video cards. Make sure we check VBE version
before fiddling around with DDC.
http://bugzilla.kernel.org/show_bug.cgi?id=1458
Opened: 2003-10-30 09:12 Last update: 2007-02-13 22:03
Much thanks to Tobias Hain for help in testing and investigating the bug.
Tested on;
i386, Chips & Technologies 65548 VESA VBE 1.2
CONFIG_VIDEO_SELECT=Y
CONFIG_FIRMWARE_EDID=Y
Untested on x86_64.
Signed-off-by: Zwane Mwaikambo <zwane@infradead.org>
Signed-off-by: Andi Kleen <ak@suse.de>
The MSR reservation is per CPU and oprofile would only allocate them
on the CPU it was initialized on. Change this to handle all CPUs.
This also fixes a warning about unprotected use of smp_processor_id()
in preemptible kernels.
Signed-off-by: Andi Kleen <ak@suse.de>
AMD dual core laptops with C1E do not run the APIC timer correctly
when they go idle. Previously the code assumed this only happened
on C2 or deeper. But not all of these systems report support C2.
Use a AMD supplied snippet to detect C1E being enabled and then disable
local apic timer use.
This supercedes an earlier workaround using DMI detection of specific systems.
Thanks to Mark Langsdorf for the detection snippet.
Signed-off-by: Andi Kleen <ak@suse.de>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] SMTC: Fix recursion in instant IPI replay code.
[MIPS] BCM1480: Fix setting of irq affinity.
[MIPS] do_page_fault() needs to use raw_smp_processor_id().
[MIPS] SMTC: Fix false trigger of debug code on single VPE.
[MIPS] SMTC: irq_{enter,leave} and kstats keeping for relayed timer ints.
[MIPS] lockdep: Deal with interrupt disable hazard in TRACE_IRQFLAGS
[MIPS] lockdep: Handle interrupts in R3000 style c0_status register.
[MIPS] MV64340: Add missing prototype for mv64340_irq_init().
[MIPS] MT: MIPS_MT_SMTC_INSTANT_REPLAY currently conflicts with PREEMPT.
[MIPS] EV64120: Include <asm/irq.h> to fix warning.
[MIPS] Ocelot: Fix warning.
[MIPS] Ocelot: Give PMON_v1_setup a proper prototype.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Fix arch/ia64/pci/pci.c:571: warning: `return' with a value
[IA64] Speed up boot - skip unnecessary clock calibration
[IA64] bugfix stack layout upside-down
[IA64] Fix possible invalid memory access in ia64_setup_msi_irq()
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
local_irq_restore -> raw_local_irq_restore -> irq_restore_epilog ->
smtc_ipi_replay -> smtc_ipi_dq -> spin_unlock_irqrestore ->
_spin_unlock_irqrestore -> local_irq_restore
The recursion does abort when there is no more IPI queued for a CPU, so
this isn't usually fatal which is why we got away with this for so long
until this was discovered by code inspection.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make smtc_setup_irq() update the list of interrupts which need to be
watched by the debug code itself. Also there is no need to initialize the
IPI swint when running with a single VPE, so don't initialize it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Between the mtc0 or di instruction that disables interrupts and the
following hazard barrier a processor may still take interrupts. If an
interrupt is taken after interrupts are disabled but before the state
is updated it will appear to restore_all that it is incorrectly returning
with interrupts disabled.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Check the IEP bit for R3000 style processors when checking to see if
interrupts will be reenabled in restore_all.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So until MIPS_MT_SMTC_INSTANT_REPLAY has been rewritten to solve this
issue, don't allow selecting it with PREEMPT.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Skip clock calibration if cpu being brought online is exactly the same
speed, stepping, etc., as the previous cpu. This significantly reduces
the time to boot very large systems.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ia64 expects following vm layout:
== low memory
[register-stack grows up]
[memory-stack grows down]
== high memory
But the code assigns the base of the register stack at the
maximum stack size offset from the fixed address where the
stack *might* start. Stack randomization will result in the
memory stack starting at a lower address than this, and if the
user has set a low stack limit with "ulimit -s", then you can
end up with the register stack above the memory stack (or if
you were very unlucky right on top of it!).
Fix: Calculate the base address for the register stack starting
from the actual address of the memory stack.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following 'if' statement in ia64_setup_msi_irq() always fails even
if create_irq() returns <0 value, because variable 'irq' is defined as
unsigned int. It would cause invalid memory access.
irq = create_irq();
if (irq < 0)
return irq;
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add support for the MPC8323E Reference Development Board (RDB). The board
is a mini-ITX reference board with 64M DDR2, 16M flash, USB, PCI,
10/100 ethernet, serial, and phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct the alignment of the internal buffer used by the QUICC Engine
SDMA controller to 4Kbytes. Correct the shift direction in the logic
that sets up the SDMR register for the QUICC Engine SDMA controller.
Signed-off-by: Chuck Meade <chuckmeade@mindspring.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds support of suspend/resume on i386 for HPET, which fixes a
number of timer-related failures around STR.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Acked-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a few miscellaneous compilation problems -
an assignment with mismatched types in ldt.c
a missing include in mconsole.h which needs a definition of uml_pt_regs
I missed removing an include of user_util.h in hostfs
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Permit lvm to create logical volumes without crashing UML.
When device-mapper's DM_DEV_CREATE_CMD ioctl is called to create a new device,
dev_create()->dm_create()->alloc_dev()-> blk_queue_bounce_limit(md->queue,
BLK_BOUNCE_ANY) is called.
blk_queue_bounce_limit(BLK_BOUNCE_ANY) calls init_emergency_isa_pool() if
blk_max_pfn < blk_max_low_pfn. This is the case on UML, but
init_emergency_isa_pool() hits BUG_ON(!isa_page_pool) because there doesn't
seem to be a dma zone on UML for mempool_create() to allocate from.
Most architectures seem to have max_low_pfn == max_pfn, but UML doesn't
because of the uml_reserved chunk it keeps for itself. From what I can see,
max_pfn and max_low_pfn don't get much use after the bootmem-allocator stops
being used anyway, except that they initialize the block layer's
blk_max_low_pfn/blk_max_pfn.
This ensures init_emergency_isa_pool() doesn't crash uml in this situation by
setting max_low_pfn == max_pfn in mem_init().
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the comment immediately preceding this points out, this list is changed in
irq context, so it needs to be protected with spin_lock_irqsave in process
context when it is processed.
Sometimes, gcc should just compile the comments and forget the code.
The IRQ side of this was better, in the sense that it blocked and unblocked
interrupts, but it still should have saved and restored them.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a NULL dereference when unplugging a device. The default value of
err_msg wants to be "" in case the driver doesn't modify it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 62f96cb01e introduced per-devices
queues and locks, which was fine as far as it went, but left in place a
global which controlled access to submitting requests to the host. This
should have been made per-device as well, since it causes I/O hangs when
multiple block devices are in use.
This patch fixes that by replacing the global with an activity flag in the
device structure in order to tell whether the queue is currently being run.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the NAND flash timings on the AT91SAM9260.
The current timings lead to the detection of a number of bad blocks.
These timings are now set the same as on the AT91SAM9263.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a bug in dcr_unmap().
At unmap time the DCR offset need to be added instead of substracted.
Signed-off-by: Jean-Christophe Dubois <jdubois@mc.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
So I think the right solution is to simply make pci_enable_device just
flip enable bits and move the rest of the work someplace else.
However a thorough cleanup is a little extreme for this point in the
release cycle, so I think a quick hack that makes the code not stomp the
irq when msi irq's are enabled should be the first fix. Then we can
later make the code not change the irqs at all.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__sdivsi3_i4i, __udiv_qrnnd_16, and __udivsi3_i4i don't exist
outside of the ST compiler, so kill them off.
This causes compile failures with other GCC4 compilers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit 94985134b7 and
insteads removes the WARN_ON() that caused that commit in the first
place.
The problem is that we call disable_nonboot_cpus() in swsusp before
powering down the system in order to avoid triggering the WARN_ON()
in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping() and this doesn't
work well on Thomas' system.
So instead, remove the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:
init_low_mapping(), which triggers every time during the suspend to disk
in the platform mode, as the potential problem it is related to doesn't
seem to occur in practice.
[ I think we might want to disallow the case of multiple users of that
mm, or something. Normally, playing with the current process page
tables on the current CPU should be fine as long as we don't have
other threads using those tables at the same time..
Anyway, not pretty, but better than the warning or the lockup - Linus ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clockevents / tick management code expects an error value, when the
event is already expired. hpet_next_event() returns 1 in that case.
Fix it to return the proper -ETIME error code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch uses MAX_REG_NR consistently to refer to the register file size.
FRAME_SIZE isn't sufficient because on x86_64, it is smaller than the
ptrace register file size. MAX_REG_NR was introduced as a consistent way
to get the number of registers, but wasn't used everywhere it should be.
When this causes a problem, it makes PTRACE_SETREGS fail on x86_64 because
of a corrupted segment register value in the known-good register file. The
patch also adds a register dump at that point in case there are any future
problems here.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit b19cbe2a16 [BRIDGE]: Fix fdb RCU
race
breaks sparc SMP build because atomic_add_unless is not exported.
This patch exports atomic_add_unless and atomic_cmpxchg.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
mpc832x_mds.h was exporting a function that didn't exist anymore. Once removed
the header had no purpose.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In two places, ucc_slow_init() passes a physical address instead of the
virtual address to functions that were expecting the latter, causing a kernel
panic. us_info->regs contains the physical address of the UCC register set.
The registers are ioremap'd to kernel space, and the virtual pointers are
stored in us_regs. The code was using us_info->regs when it should have been
using us_regs.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Delete apparently unused header file
arch/powerpc/platforms/83xx/mpc834x_itx.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the Kconfig files so that the Freescale QE options are automatically
selected if a QE device is selected. Previously, you'd need to manually
select UCC_FAST if you want any "fast" UCC devices, such as Gigabit Ethernet.
Now, the QE Gigabit Ethernet option is always available if the device has a
QE, and UCC_FAST is automatically enabled. A side-effect is that the
"QE Options" menu no longer exists.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This move sets the stage for the use of generic PCI Express
code in 85xx and 86xx parts from FSL. Subsequent patches
for 8548 and 8544 will be able to use this shared code.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: Fix ap_poll_requests counter in lost requests error path.
[S390] zcrypt: Fix possible dead lock in AP bus module.
[S390] cio: Device status validity.
[S390] kprobes: Align probe address.
[S390] Fix TCP/UDP pseudo header checksum computation.
[S390] dasd: Work around gcc bug.
This patch automatically enables pci=bfsort for the Dell PowerEdge
R900. This is necessary to ensure the onboard NICs enumerate in the
proper order, similar to the other systems already on the list.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Running a probe on s390 with a probe address that is not 4 byte aligned
results in a Kernel BUG. The problem is that the stura instruction used
by swap_instruction requires the destination address to be 4 byte aligned.
As stura only writes 4 bytes, aligning to the next 4 byte aligned address
results in the breakpoint instruction being stored past the probe address.
The fix is to align the address backward (to the previous 4 byte aligned
address) and writing the two byte breakpoint instruction in the appropriate
bytes.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This patch adds a reg.h to the zImage code, with common definitions
for accessing system registers. For now, this includes functions for
retrieving the PVR and the stack pointer. This patch then uses the
new reg.h to let start() display the running stack address without
having to explicitly pass the stack as a parameter from the asm code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the correct attributes to the zImage's versions of
printf to make gcc generate format string mismatch warnings. It also
corrects several minor problems with format strings in the zImage thus
discovered.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Before the plethora of platforms gets any worse, establish a common
rule to invoke the wrapper for any platform. Add arguments to
the rule for initrd, dts, dtb, etc. Show example usage with initrd.
Create default rules for zImage, and zImage.initrd. initrd targets
depend on the ramdisk file.
Don't consider targets for zImage.initrd that are targets for zImage.
This means uImage is no longer considered a target for zImage.initrd.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that obj-boot is in targets, we can remove (twice) it from clean-files.
zImage.initrd was missing, move zImage nearer where its used, and place
zImage.initrd next to it. Remove non-ported zImage.sandpoint, and add
auto-generation of unconfigured zImage.initrd* like image-.
Signed-off-by: Milton Miller <miltonm@bga.com>
--
Testing: did a few builds and cleans
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kbuild if_changed and if_changed_dep require the use of the dummy
FORCE to get the dependencies right. Also add to targets to get
correct behavior.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some platforms might need to run some code before the zImage start, but
could otherwise use the bss clear and relocation code. Export the
start address strongly as zImage_start_lib.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a macro fatal that calls printf then exit. User must include stdio.h.
Typically replaces 3 lines with 1, although I added back some whitespace.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes the time suspend/restore code that was done through
a PMU notifier in arch/platforms/powermac/time.c.
Instead, introduce arch/powerpc/sysdev/timer.c which creates a sys
device and handles time of day suspend/resume through that.
This should probably be replaced by using the generic RTC framework
but for now it gets rid of the arcane powermac specific hack.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the configuration of the PCIX PCI->PLB inbound memory window
to be 2GB instead of 512kB. The comment already mentioned 2GB, but the
code unfortunately didn't reflect this.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use lowercase for hex printouts in oops messages. The number of times I have
tried to copy and paste from an oops into an objdump search...
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Looks like someone got this backwards, highlighting the perils of the
? : !!! :)
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Handle recursive oopses, like on x86. We had a few cases recently where
we locked up in oops printing and didnt make it into crashdump.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move pmac_backlight_unblank into its own function and only take the
pmac_backlight_mutex when we are on a pmac for that added bit of
paranoia.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit f9690982b8 removed the check for
cpu_khz from sched_clock(), which prevented early access to the TSC by
non obvious magic.
This is harmless as long as the CPU has a TSC. On TSCless systems this
results in an illegal instruction trap.
Replace tsc_disabled and tsc_unstable by tsc_enabled, which is only set
when the tsc is available and not unstable.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CC arch/mips/mm/cerr-sb1.o
arch/mips/mm/cerr-sb1.c: In function 'sb1_cache_error':
arch/mips/mm/cerr-sb1.c:235: warning: format '%010llx' expects type 'long long unsigned int', but argument 2 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c: In function 'extract_ic':
arch/mips/mm/cerr-sb1.c:385: warning: format '%016llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c:385: warning: format '%016llX' expects type 'long long unsigned int', but argument 6 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c: In function 'extract_dc':
arch/mips/mm/cerr-sb1.c:523: warning: format '%010llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c:523: warning: format '%016llX' expects type 'long long unsigned int', but argument 7 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c:570: warning: format '%016llX' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
LD arch/mips/mm/built-in.o
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes two places where we used plain 'x - PAGE_OFFSET' to
achieve virtual to physical address convertions. This type of convertion
is no more allowed since commit 6f284a2ce7.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
[Build fixes for machines that don't use the generic dma-coherence.h]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ray Lee reported, that on an UP kernel with "noapic" command line option
set, the box locks hard during boot.
Adding some debug printks revealed, that the last action on the box
before stalling was "Send IPI" - a debug printk which was put into
smp_send_timer_broadcast_ipi().
It seems that send_IPI_mask(mask, LOCAL_TIMER_VECTOR) fails when
"noapic" is set on the command line on an UP kernel.
Aside of that it does not make much sense to trigger an interrupt
instead of calling the function directly on the CPU which gets the
PIT/HPET interrupt in case of broadcasting.
Reported-by: Ray Lee <ray-lk@madrabbit.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ray Lee <ray-lk@madrabbit.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Needed for any architecture that claims ARCH_APICTIMER_STOPS_ON_C3,
not just i386.
I'm hoping Thomas will clean this up a bit later..
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turned out that it is almost impossible to trust ACPI, BIOS & Co.
regarding the C states. This was the reason to switch the local apic
timer off in C2 state already. OTOH there are sane and well behaving
systems, which get punished by that decision.
Allow the user to confirm that the local apic timer is trustworthy in C2
state. This keeps the default behaviour on the safe side.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: IA64: fix %ll build warnings
ACPI: IA64: fix allnoconfig build
ACPI: Only use IPI on known broken machines (AMD, Dothan/BaniasPentium M)
ACPI: ibm-acpi: allow module to load when acpi notifiers can't be set (v2)
ACPI: parse 2nd MADT by default
ACPICA: revert "acpi_serialize" changes
sony-laptop: MAINTAINERS fix entry, add L: and W:
ACPI: resolve HP nx6125 S3 immediate wakeup regression
ACPI: Add support to parse 2nd MADT
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bypass hcall stats until cpu features have run
[POWERPC] Avoid hypervisor statistics calculation in real mode
[POWERPC] Fix atomicity of TIF update in flush_thread()
latest -git triggers an irqtrace/lockdep warning of a leaked
irqs-off condition:
BUG: at kernel/fork.c:1033 copy_process()
after some debugging it turns out that commit ca1b940c accidentally left
interrupts disabled - which trickled down all the way to the first time
we fork a kernel thread and triggered the warning.
the fix is to re-enable interrupts in the 'else' branch of
setup_boot_APIC_clock()'s pmtimers calibration path.
Reported-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@brown.paperbag.linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local APIC timer stops to work in deeper C-States. This is handled by
the ACPI code and a broadcast mechanism in the clockevents / tick managment
code.
Some systems do not expose the deeper C-States to the kernel, but switch
into deeper C-States behind the kernels back. This delays the local apic
timer interrupts for ever and makes the systems unusable.
Add a command line option to disable the local apic timer and a dmi
quirk for known broken systems.
Andi sayeth:
While not wrong by itself i think it is still better to use some heuristic
-- like "has battery in ACPI" With the DMI table if the problem is more wide
spread we will just continue extending it.
But anyways should be ok now for .21 although I'm not really happy with
it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Grudgingly-acked-by: Andi Kleen <ak@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PIT has no dedicated mode for shut down. The only way to disable PIT
is to put it into one shot mode. AMD implementations of PIT on Geode
(also observed on Cyrix) are confused by an "empty" transition from
CLOCK_EVT_MODE_UNUSED to CLOCK_EVT_MODE_SHUTDOWN, which puts the PIT
into one shot mode momentarily.
I realized after staring helpless at the bug report
http://bugzilla.kernel.org/show_bug.cgi?id=8027 for quite a while, that
the only change, which might influence the bogomips calibration, is the
above transition during the PIT initialization.
Avoiding the unnecessary switch to oneshot and later to periodic mode
fixes the weird bogomips value and also the resulting slowness.
The fix is confirmed on OLPC and another Geode based box.
Note: this is unrelated to the Dual Core problem discussed here:
http://lkml.org/lkml/2007/3/17/48
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split "Platform support" menu out from arch/powerpc/Kconfig into
arch/powerpc/platforms/Kconfig in prep for allowing other sub-arches to
be configured via a single "Platform support" menu.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved pseries, iseries, chrp, prep, maple and pasemi into their respective
arch/powerpc/platform/*/Kconfig files out of arch/powerpc/Kconfig
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we started arch/powerpc we duplicated a number of config options from
arch/ppc for various platforms that are supported. Now that we actually
support a few platforms, remove all the ones that haven't been moved over.
Additionally, this cleanup moved the 82xx/PQ2 options over into
arch/powerpc/platforms/82xx/Kconfig where they belong. It also killed
GEN550 which doesn't exist in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove last_syscall from 32bit powerpc, its been gone in 64bit for years.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We already have an inline __get_SP, no need for yet another one.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rework how multi-function PCI devices are identified and traversed.
This fixes a bug with multi-function recovery on Power4 that was
introduced by a recent Power4 EEH patch.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After requesting a state change, verify that the state change
actually ocurred, and the system ends up in the expected state.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The EEH event notification system passes around data that is
not needed or at least, not used properly. Stop passing this
data; get it in a more reliable fashion.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
