ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The previous code did something like,
if (error) goto out_err;
....
do {
struct au1000_pcmcia_socket *skt = PCMCIA_SOCKET(i);
del_timer_sync(&skt->poll_timer);
pcmcia_unregister_socket(&skt->socket);
out_err:
flush_scheduled_work();
ops->hw_shutdown(skt);
i--;
} while (i > 0)
.....
- On the error path, skt would not contain a valid value for the first
iteration (skt is masked by uninitialized automatic skt)
- Does not do hw_shutdown() for 0th element of PCMCIA_SOCKET
Signed-off-by: Om Narasimhan <om.turyx@gmail.com>
Cc: "Yoichi Yuasa" <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
debugging goo removed to not leave assymetry in it after possible "leave"
removal.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove some code which is unneeded if CONFIG_PM=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Some PCMCIA cards do not mention specific IO addresses in the CIS. In that
case, inside the alloc_io_space function, conflicts are detected (the
function returns 1) for the second function of a multifunction card unless
the length of IO address range required is greater than 0x100.
The following patch will remove this conflict checking for a PCMCIA
function which had not mentioned any specific IO address to be mapped from.
The patch is tested for Linux kernel 2.6.15.4 and works fine in the above
case and is as suggested by Dave Hinds.
Signed-off-by: Kaustav Majumdar <kaustav.majumdar@wipro.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As a replacement for the broad manufactor/card ID match we commented out
because of conflicts with pcnet_cs, add two product ID matches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
More correct AT91 CF wakeup logic ... only enable/disable the IRQ wakeup
capability, not the IRQ itself. That way the we know that the IRQ will be
disabled correctly, in suspend/resume logic instead of ARM IRQ code.
Most of the pin multiplexing setup has moved to the devices.c setup code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This is a cross-port of a similar patch for aic7xxx;
only it's a bit simpler here as we don't support HVD
and all controller actually implement this register.
I hope.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a cross-port from aic79xx; we still hit the occasional
BUG_ON in slave_destroy. And again we don't really need the
slave_destroy callback nor the ahc_linux_target structure
at all.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
aic79xx has a special 'iocell' chip which handles the precompensation.
If it's set via DV we should make sure to set the chip correctly, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Whenever an external device is resetted we really have to take
care to keep the channel in sync. Just notifying SCSI-ML and retry
is not enough as we have to make sure the SCSI bus is not getting
confused, either.
So whenever we detect an external reset we rewrite the command to
TUR, disable packetized command and notify the internal engine
that an abort has happened. This way we trigger a proper bus
reset sequence and all devices will be renegotiated properly.
Kudos to Justin Gibbs and Luben Tuikov for this idea.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix printk format warning:
drivers/scsi/lpfc/lpfc_attr.c:597: warning: long long unsigned int format, uint64_t arg (arg 4)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- make needlessly global code static
- #if 0 the following unused global functions:
- aic79xx_core.c: ahd_print_scb
- aic79xx_core.c: ahd_suspend
- aic79xx_core.c: ahd_resume
- aic79xx_core.c: ahd_dump_scbs
- aic79xx_osm.c: ahd_softc_comp
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanups done to use min/max macros from kernel.h. Handcrafted MIN/MAX
macros are changed to use macros in kernel.h
[akpm@osdl.org: fix warning]
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for REPORT TARGET PORT GROUPS. This is used
eg for the multipathing priority callout to determine the path
priority.
With this patch multipath-tools can use the existing mpath_prio_alua
callout to exercise the path priority grouping.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix typo in check of return value of qla1280_bus_reset() which would
result in an adapter reset in addition to the bus reset.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to the iscsi RFC, we cannot send other requests if
we have sent a logout pdu. This patch enforces this requirement
by blocking the session and suspending the send thread. Userspace
decides if we restart the connection or if we just free everything.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have been dropping the pdu. We should just send it to userspace
and let it handle it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from bhalevy@gmail.com:
It looks like change 652 to libiscsi.c added some dead code around line
670
if (rc) {
spin_unlock_bh(&conn->session->lock);
goto again;
}
since 5 lines above we goto again if (rc).
It looks like the previous if (rc) should go away if we want to put the
ctask before
breaking out of the while loop with "goto again" (see following patch).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If connection creation fails we end up calling list_del
on a invalid struct. This then causes an oops. We are not
acutally using the lists (old MCS code we thought might
be useful elsewhere) so this patch just removes that
code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The transport class recv mempools are causing slab corruption.
We could hack around netlink's lack of mempool support like dm,
but it is just too ulgy (dm's hack is ugly enough :) when you need
to support broadcast.
This patch removes the recv pools. We have not used them even when
we were allocting 20 MB per session and the system only had 64 MBs.
And we have no pools on the send side and have been ok there. When
Peter's work gets merged we can use that since the network guys
are in favor of that approach and are not going to add mempools
everywhere.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Doesn't make the hardware hot pluggable but does ensure the driver won't
crash when another device is hot-unplugged at the wrong moment. Soon I
propose to deprecate pci_find_device() and some of its friends.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Debugging TCQ issues has shown me this is a very useful parameter to be
able to view. Add it to he host class parameters.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It is known that 2 LSI Logic MegaRAID SATA RAID Controllers (150-4 and
150-6) don't support 64-bit DMA. Unfortunately currently this check is
wrong and driver sets 64-bit DMA mode for these devices.
Signed-off-by: Andrey Mirkin <amirkin@sw.ru>
Acked-by: "Ju, Seokmann" <Seokmann.Ju@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add PCI id. Plus correct for possibly missing resistor that can cause
FLASHEX to have the wrong value.
Signed-off-by: Sergey Kononenko <sergk@sergk.org.ua>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The "ibmvscsi: treat busy and error conditions separately" patch
submitted by Dave Boutcher back in June incorrectly reenables the CRQ.
The broken logic causes the adapter to get disabled if the CRQ
connection happens to close temporarily. This patch "fixes that
obviously wrong logic check" (Dave's words).
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: David Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Drop queue-depths across all luns for a given fcport
during TASK_SET_FULL statuses.
- Ramp-up I/Os after throttling.
- Consolidate completion-status handling of CS_QUEUE_FULL with
CS_COMPLETE as ISP24xx firmware no longer reports
CS_QUEUE_FULL.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Early ISP2432 parts have a known hardware issue when coming
out of a D3 hot state. This issue can result in a hung PCIe
link. Recent firmwares contain a workaround whereby the
stop-firmware mailbox command prevents the ISP from entering
the D3 hot state.
In order to ensure that the workaround succeeded the driver
must verify that the stop-firmware mailbox command completes
successfully. In the event of a failure, the driver
attempts a shutdown-retry after resetting the ISP and
re-executing firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in the Fibre Channel
driver (fc4).
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete typedefd Scsi_Cmnd to struct scsi_cmnd in
the ninja scsi pcmcia driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in psi240i-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we fail to allocate mp->virt during the first while loop iteration,
mlist is still uninitialized, therefore we should check if before
dereferencing.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes a typo in the aic7xxx_old.c.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Thanks to James Smart for the inspiration.
Stall error handler if attempting recovery while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Also verify that VirtDevice is available before issuing scsi command.
VirtDevice is removed when fc transport removes a target.
See James Smart's patch of 08/17/2006 for greater detail.
http://marc.theaimsgroup.com/?l=linux-scsi&m=115583213624803&w=2
Also bump version number per Eric's request.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Eric Moore <eric.moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to the adaptec sources aic7xxx / aic79xx really can do
4MB transfers. So we should adjust .max_sectors.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a dup printk at the tail of qla4xxx_module_init(). Remove the
first instance as it's before the complete success of the function.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
AM53C974A's Start Transfer Counter register has 24 bits, thus
maximum transfer length is 16MiB. But the maximum I can test
is 8MiB, so use that until somebody tests 16MiB.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Based on the original patch from Hannes Reinecke <hare@suse.de>
Fix st_open() to return -ENOMEDIUM instead of -EIO if no medium is
found.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change obsolete Scsi_Cmnd to struct scsi_cmnd in the Qlocic FAS408 driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change the obsolete Scsi_Cmnd to struct scsi_cmnd in the sun3-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
All callers and the function itself dereference dinfo, so we can remove the
check. (coverity id #1371)
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only) to make sure the files are compiling without
any warning/error due to new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
- callers of drm_sysfs_create() and drm_sysfs_device_add() looked for
errors using IS_ERR(), but the functions themselves only ever returned
NULL on error. Fixed.
- unwind from, and propagate sysfs errors
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The other failure returns in this function are negative, so make
this one do the same.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
CRYPTO_MANAGER is selected automatically by CONFIG_ECB and CONFIG_CBC.
config CRYPTO_ECB
tristate "ECB support"
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
I've added CONFIG_ECB to the ones you mentioned and CONFIG_CBC to
gssapi.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Account for the interface being closed before disabling polling
on a device, to fix shutdown on some systems that explcitly close
the netdevice before calling shutdown.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Move the length (rx_bytes counter) adjustment of 4 bytes down to after the
TBI_ACCEPT workaround.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
82571 and newer chispets don't need to limit desc. length to 4kb and can
handle 8kb sizes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allocations using alloc_page are taking too long for normal MTU, so
use LPE only for jumbo frames.
Signed-off-bu: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Threshold bitmasks for prefetch, host and writeback were clearing
bits that they were not supposed to. The leftmost 2 bits in the byte
for each threshold are reserved.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The MANC register should not be read for PCI-E adapters at all, as well as
82543 and older where 82543 would master abort when this register was
accessed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Fix module loading:
corgi_bl: module license 'GPLv2' taints kernel.
corgi_bl: Unknown symbol platform_driver_unregister
corgi_bl: Unknown symbol __symbol_get
corgi_bl: Unknown symbol platform_driver_register
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix module compiling:
WARNING: drivers/video/backlight/corgi_bl.o - Section mismatch:
reference to .init.text: from .data between '$d' (at offset 0x0) and
'bl_mutex'
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
only allow specific type-3 packets to pass the verifier instead of all for r100/r200 as others might be unsafe (r300 already does this), and add checking for these we need but aren't safe. Check the RADEON_CP_INDX_BUFFER packet on both r200 and r300 as it isn't safe neither.
Signed-off-by: Dave Airlie <airlied@linux.ie>
In commit 4e8a520150 ("[PKT_SCHED] netem:
Orphan SKB when adding to queue.") Davem mistakenly also included a
temporary diff in his tree that disabled the pci_fixup_video VGA quirk,
which broke sparc64.
This reverts that part of the commit. Sayeth Davem:
"Greg KH has a patch coming to you soon which will move that VGA code
back into x86/x86_64/IA64 specific areas and will fix the sparc64
problem properly."
Special thanks to Claudio Martins <ctpm@ist.utl.pt> for noticing the
error in the first place.
Cc: Claudio Martins <ctpm@ist.utl.pt>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[PKT_SCHED] netem: Orphan SKB when adding to queue.
[NET]: kernel-doc fix for sock.h
[NET]: Reduce sizeof(struct flowi) by 20 bytes.
[IPv6] fib: initialize tb6_lock in common place to give lockdep a key
[ATM] nicstar: Fix a bogus casting warning
[ATM] firestream: handle thrown error
[ATM]: No need to return void
[ATM]: handle sysfs errors
[DCCP] ipv6: Fix opt_skb leak.
[DCCP]: Fix Oops in DCCPv6
The networking emulator can queue SKBs for a very long
time, so if you're using netem on the sender side for
large bandwidth/delay product testing, the SKB socket
send queue sizes become artificially larger.
Correct this by calling skb_orphan() in netem_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Not enough to make Nicstar 64bit friendly but got squashed in passing so might
as well be applied
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc emits the following warning:
drivers/atm/firestream.c: In function ‘fs_open’:
drivers/atm/firestream.c:870: warning: ‘tmc0’ may be used uninitialized in this function
This indicates a real bug. We should check make_rate() return value for
potential errors.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The module_exit function has return-type void and pci_unregister_driver()
returns void anyway.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] libata-sff: Allow for wacky systems
[PATCH] ahci: readability tweak
[PATCH] libata: typo fix
[PATCH] ATA must depend on BLOCK
[PATCH] libata: use correct map_db values for ICH8
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (22 commits)
[PATCH] ibmveth: Fix index increment calculation
[PATCH] Fix timer race
[PATCH] Remove useless comment from sb1250
[PATCH] ucc_geth: changes to ucc_geth driver as a result of qe_lib changes and bugfixes
[PATCH] sky2: 88E803X transmit lockup
[PATCH] e1000: Reset all functions after a PCI error
[PATCH] WAN/pc300: handle, propagate minor errors
[PATCH] Update smc91x driver with ARM Versatile board info
[PATCH] wireless: WE-20 compatibility for ESSID and NICKN ioctls
[PATCH] zd1211rw: fix build-break caused by association race fix
[PATCH] sotftmac: fix a slab corruption in WEP restricted key association
[PATCH] airo: check if need to freeze
[PATCH] wireless: More WE-21 potential overflows...
[PATCH] zd1201: Possible NULL dereference
[PATCH] orinoco: fix WE-21 buffer overflow
[PATCH] airo.c: check returned values
[PATCH] bcm43xx-softmac: Fix system hang for x86-64 with >1GB RAM
[PATCH] bcm43xx-softmac: check returned value from pci_enable_device
[PATCH] softmac: Fix WX and association related races
[PATCH] bcm43xx: fix race condition in periodic work handler
...
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Revert timer routing behaviour back to 2.6.16 state
[PATCH] x86-64: Overlapping program headers in physical addr space fix
[PATCH] x86-64: Put more than one cpu in TARGET_CPUS
[PATCH] x86: Revert new unwind kernel stack termination
[PATCH] x86-64: Use irq_domain in ioapic_retrigger_irq
[PATCH] i386: Disable nmi watchdog on all ThinkPads
[PATCH] x86-64: Revert interrupt backlink changes
[PATCH] x86-64: Fix ENOSYS in system call tracing
[PATCH] i386: Fix fake return address
[PATCH] x86-64: x86_64 add NX mask for PTE entry
[PATCH] x86-64: Speed up dwarf2 unwinder
[PATCH] x86: Use -maccumulate-outgoing-args
[PATCH] x86-64: fix page align in e820 allocator
[PATCH] x86-64: Fix for arch/x86_64/pci/Makefile CFLAGS
[PATCH] i386: fix .cfi_signal_frame copy-n-paste error
[PATCH] x86-64: typo in __assign_irq_vector when updating pos for vector and offset
[PATCH] x86-64: x86_64 hot-add memory srat.c fix
[PATCH] i386: Update defconfig
[PATCH] x86-64: Update defconfig
CCISS was producing warnings about shifts being greater than the size of
the type and pointers being of incompatible type. Turns out this is
because it's calling do_div on a 32-bit quantity. Upon further
investigation, the sector_t total_size is being assigned to an int, and
then we're calling do_div on that int. Obviously, sector_div is called for
here, and I took the chance to refactor the code a little.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Just like everyone else.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent commit 751ae21c6c introduced a bug
in the producer/consumer index calculation in the ibmveth driver -
incautious use of the post-increment ++ operator resulted in an increment
being immediately reverted. This patch corrects the logic.
Without this patch, the driver oopses almost immediately after activation
on at least some machines.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Acked-by: Santiago Leon <santil@us.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have an acpi_pm that goes backwards, but it's not intel. I tested the
verified read and my acpi_pm started to function properly. So I added it
to the greylist. I'm assuming that's the right spot.
I also added an unlikely() to the while, cause it seems appropriate.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
And a couple of bug fixes found by sparse.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Includes a couple of bugfixes found by sparse.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two less-used md personalities have bugs in the calculation of ->degraded (the
extent to which the array is degraded).
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The change from __setup() to module_param_named() requires users to prefix
the option with "generic.".
This patch re-adds the __setup() additionally to the module_param_named().
Usually it would make sense getting rid of such an obsolete __setup() at
some time, but considering that drivers/ide/ is slowly approaching a RIP
status it's already implicitely scheduled for removal.
This patch fixes kernel Bugzilla #7353.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commits 881a8c120a and
efe1ec2783 corrects pci device matching in
only one way; it no longer oopses/crashes, despite hotplug is not solved
in these changes.
Whenever pci_find_device -> pci_get_device change is performed, also
pci_dev_get and pci_dev_put should be in most cases called to properly
handle hotplug. This patch does exactly this thing -- increase refcount
to let kernel know, that we are using this piece of HW just now.
It affects moxa and rio char drivers.
Cc: <R.E.Wolff@BitWizard.nl>
Acked-by: Amit Gud <gud@eth.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are some Linux supported platforms that simply cannot hit the low
I/O addresses used by ATA legacy mode PCI mappings. These platforms have
a window for PCI space that is fixed by the board logic and doesn't
include the neccessary locations.
Provide a config option so that such platforms faced with a controller
that they cannot support simply error it and punt
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the following compile error with CONFIG_ATA=y, CONFIG_BLOCK=n:
...
CC drivers/ata/libata-scsi.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c: In function ‘ata_scsi_dev_config’:
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:791: warning: implicit declaration of function ‘blk_queue_max_sectors’
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:799: error: ‘request_queue_t’ undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:799: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:799: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:799: error: ‘q’ undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:800: warning: implicit declaration of function ‘blk_queue_max_hw_segments’
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c: In function ‘ata_scsi_slave_config’:
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:831:
warning: implicit declaration of function ‘blk_queue_max_phys_segments’
make[3]: *** [drivers/ata/libata-scsi.o] Error 1
Bug report by Jesper Juhl.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use valid values for ICH8 map_db. With the old values, when the
controller was in Native mode, and SCC was 1 (drives configured for
IDE), any drive plugged into a slave port was not recognized. For
Combined Mode (and SCC is still 1), 2 is a value value for MAP.map_value,
and needs to be recognized.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Thu, Oct 12, 2006 at 06:22:14PM +1000, David Gibson wrote:
> Your recent ibmveth commit, 751ae21c6c
> ("fix int rollover panic"), causes a rapid oops on my test machine
> (POWER5 LPAR).
>
> I've bisected it down to that commit, but am still investigating the
> cause of the crash itself.
Found the problem, I believe: an object lesson in the need for great
caution using ++.
[...]
@@ -213,6 +213,7 @@ static void ibmveth_replenish_buffer_poo
}
free_index = pool->consumer_index++ % pool->size;
+ pool->consumer_index = free_index;
index = pool->free_map[free_index];
ibmveth_assert(index != IBM_VETH_INVALID_MAP);
Since the ++ is used as post-increment, the increment is not included
in free_index, and so the added line effectively reverts the
increment. The produced_index side has an analagous bug.
The following change corrects this:
The recent commit 751ae21c6c introduced
a bug in the producer/consumer index calculation in the ibmveth driver
- incautious use of the post-increment ++ operator resulted in an
increment being immediately reverted. This patch corrects the logic.
Without this patch, the driver oopses almost immediately after
activation on at least some machines.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When closing the driver or reinitializing the hardware there is the
usual del_timer() race condition that exists when timers re-add
themselves. Fix by conversion to del_timer_sync().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
changes due to qe_lib changes include:
o removed inclusion of platform header file
o removed platform_device code, replaced with of_device
o removed typedefs
o uint -> u32 conversions
o removed following defines:
QE_SIZEOF_BD, BD_BUFFER_ARG, BD_BUFFER_CLEAR, BD_BUFFER,
BD_STATUS_AND_LENGTH_SET, BD_STATUS_AND_LENGTH, and BD_BUFFER_SET
because they hid sizeof/in_be32/out_be32 operations from the reader.
o removed irrelevant comments, added others to resemble removed BD_ defines
o const'd and uncasted all get_property() assignments
bugfixes, courtesy of Scott Wood, include:
- Read phy_address as a u32, not u8.
- Match on type == "network" as well as compatible == "ucc_geth", as
device_is_compatible() will only compare up to the length of the
test string, allowing "ucc_geth_phy" to match as well.
- fixes the MAC setting code in ucc_geth.c. The old code was overwriting and dereferencing random stack contents.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The reason sky2 driver was locking up on transmit on the Yukon-FE chipset
is that it was misconfiguring the internal RAM buffer so the transmitter
and receiver were sharing the same space.
The code assumed there was 16K of RAM on Yukon-FE (taken from vendor driver
sk98lin which is even more f*cked up on this). Then it assigned based on that.
The giveaway was that the registers would only hold 9bits so both RX/TX
had 0..1ff for space. It is a wonder it worked at all!
This patch addresses this, and fixes an easily reproducible hang on Transmit.
Only the Yukon-FE chip is Marvell 88E803X (10/100 only) are affected.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During the handling of the PCI error recovery sequence, the current e1000
driver erroneously blocks a device reset for any but the first PCI
function. It shouldn't -- this is a cut-n-paste error from a different
driver (which tolerated only one hardware reset per hardware card).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- move definition of 'tmc' and 'br' locals closer to usage
- handle clock_rate_calc() error
- propagate errors back to upper level open routine
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This was apparently missed by the move to the generic IRQ code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 4596c75c23 as
requested by Olaf Hering. It causes compile errors, and says Olaf:
"This change is also wrong, the autoloading works perfect with 2.6.18,
no need to add random PCI ids.
See commit a0245f7ad5, platform devices
have now a modalias entry in sysfs. The network card is not a PCI
device."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (36 commits)
[Bluetooth] Fix HID disconnect NULL pointer dereference
[Bluetooth] Add missing entry for Nokia DTL-4 PCMCIA card
[Bluetooth] Add support for newer ANYCOM USB dongles
[NET]: Can use __get_cpu_var() instead of per_cpu() in loopback driver.
[IPV4] inet_peer: Group together avl_left, avl_right, v4daddr to speedup lookups on some CPUS
[TCP]: One NET_INC_STATS() could be NET_INC_STATS_BH in tcp_v4_err()
[NETFILTER]: Missing check for CAP_NET_ADMIN in iptables compat layer
[NETPOLL]: initialize skb for UDP
[IPV6]: Fix route.c warnings when multiple tables are disabled.
[TG3]: Bump driver version and release date.
[TG3]: Add lower bound checks for tx ring size.
[TG3]: Fix set ring params tx ring size implementation
[NET]: reduce per cpu ram used for loopback stats
[IPv6] route: Fix prohibit and blackhole routing decision
[DECNET]: Fix input routing bug
[TCP]: Bound TSO defer time
[IPv4] fib: Remove unused fib_config members
[IPV6]: Always copy rt->u.dst.error when copying a rt6_info.
[IPV6]: Make IPV6_SUBTREES depend on IPV6_MULTIPLE_TABLES.
[IPV6]: Clean up BACKTRACK().
...
Add a size check in smi_data_write to prevent possible wrapping problems
with large pos values when calling smi_data_buf_realloc on 32-bit.
Signed-off-by: Doug Warzecha <Douglas_Warzecha@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These returns should be negative, like the others in this function.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I wrote a patch to avoid redundant memory hot-add call at boot time. This
was cause of strange fail message of memory hotplug like "ACPI: add_memory
failed". Memory is recognized by early boot code with EFI/E820.
But, if DSDT describes memory devices for them, then hot-add code is called
for already recognized memory, and it shows fail messages with -EEXIST.
So, sys admin will misunderstand this message as something wrong by it.
This patch avoids them by preventing redundant hot-add call until
completion of driver initialization.
[akpm@osdl.org: cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I suppose this message seems quite useless except debugging. It just shows
"Hotplug Mem Device". System admin can't know anything by this message.
So, I would like to change it to KERN_DEBUG.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch breaks C-state discovery on my IBM IntelliStation Z30 because
the return value of acpi_processor_get_power_info_fadt is not assigned to
"result" in the case that acpi_processor_get_power_info_cst returns
-ENODEV. Thus, if ACPI provides C-state data via the FADT and not _CST (as
is the case on this machine), we incorrectly exit the function with -ENODEV
after reading the FADT. The attached patch sets the value of result so
that we don't exit early.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Acked-by: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix typo (repeated) in serial Kconfig.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the concept of "queue congestion" from "backing-dev congestion".
Congestion is a backing-dev concept, not a queue concept.
The blk_* congestion functions are retained, as wrappers around the core
backing-dev congestion functions.
This proper layering is needed so that NFS can cleanly use the congestion
functions, and so that CONFIG_BLOCK=n actually links.
Cc: "Thomas Maier" <balagi@justmail.de>
Cc: "Jens Axboe" <jens.axboe@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: David Howells <dhowells@redhat.com>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When rebooting with netconsole over e100, the driver shutdown code would
deadlock with netpoll. Reduce shutdown code to a bare minimum while retaining
WoL and suspend functionality.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The device id for the Nokia DTL-4 PCMCIA card was missing. This patch
adds it back to the list of supported devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the vendor and product id of the ANYCOM Bluetooth
USB-200 and USB-250 dongles and sets a flag to send HCI_Reset as
the first command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org
As BHs are off in loopback_xmit(), preemption cannot occurs, so we can
use __get_cpu_var() instead of per_cpu() (and avoid a
preempt_enable()/preempt_disable() pair)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now with the ide.h mess sorted out, most of these boards
don't need their own directory. Move the headers out, and
update the driver paths.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The minimum tx ring size must be greater than MAX_SKB_FRAGS or 3
times that on some chips with TSO bugs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the implementation of the ethtool set ring parameters for the
tg3 transmit ring. The size of tx_pending is taken into account
before doing a netif_wake_queue. This prevents the interface from
locking up when smaller transmit ring sizes are used.
Signed-off-by: Ranjit Manomohan <ranjitm@google.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dont need a full struct net_device_stats (currently 23 long : 184 bytes on
x86_64) per possible CPU, but only two counters : bytes and packets
We save few CPU cycles too in loopback_xmit() not updating 4 fields, but 2.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'ubuntu-updates' of master.kernel.org:/pub/scm/linux/kernel/git/bcollins/ubuntu-2.6:
[pci_ids] Add Quicknet XJ vendor/device ID's.
[valkyriefb] Ifdef for when CONFIG_NVRAM isn't enabled.
[platinumfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[igafb] Add pci dev table for module auto loading.
[controlfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[hid-core] TurboX Keyboard needs NOGET quirk.
[ixj] Add pci dev table for module auto loading.
[initio] Add pci dev table for module auto loading.
[fdomain] Add pci dev table for module auto loading.
[BusLogic] Add pci dev table for auto module loading.
[mv643xx] Add pci device table for auto module loading.
[alim7101] Add pci dev table for auto module loading.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/hwmon-2.6:
hwmon: Fix debug messages in w83781d
hwmon: Let w83781d and lm78 load again
w83627ehf: Fix the detection of fan5
k8temp: Documentation update
smsc47m1: List the SMSC LPC47M112 as supported
hwmon: Fix documentation typos
adm9240: Update Grant Coady's email address
w83791d: Fix unchecked return status
Fix debug messages in w83781d at detection time. We can't use dev_dbg()
on an i2c client's device before calling i2c_attach_client() on that
client.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let the w83781d and lm78 hardware monitoring drivers load even when
no chip was detected at the ISA address. There can still be supported
chips connected to an I2C bus or SMBus.
This fixes bug #7293.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the detection of fan5 and preserve the bit between the
register writes, because the bit is write only.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the documentation for the k8temp driver.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SMSC LPC47M112 Super-I/O chip appears to be compatible with the
LPC47M10x and LPC47M13x as far as hardware monitoring is concerned.
The device ID is even the same, so it's really only a documentation
update.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace a bouncing email that I cannot recover from Mr Google.
Signed-off-by: Grant Coady <gcoady.lk@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace all unchecked calls to device_create_file with a single group
declaration, and one call to sysfs_create_group, and check that one
return status. Also remove the files on device detach.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off by: Charles Spirakis <bezaur@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Moved the attributes into a group, making the compiler be quiet about
ignoring the return value of the file create calls. This also also
fixed a bug when removing the files, which were not symlinks.
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch addresses the concern that the aoe driver should
not introduce unecessary conventions that must be learned by
the reader. It reverts patch 6.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update aoe driver version number to 32.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of starting with bio->bi_io_vec, use the offset in bio->bi_idx.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The aoe_deadsecs module parameter sets the number of seconds that
elapse before a nonresponsive AoE device is marked as dead.
This is runtime settable in sysfs or settable with a module load or
kernel boot parameter.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use simple macros to clean up the printks.
(This patch is reverted by the 14th patch to follow.)
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for jumbo ethernet frames.
(This patch depends on patch 7 to follow.)
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid memory copy on writes.
(This patch depends on fixes in patch 9 to follow.)
Although skb->len should not be set when working with linear skbuffs,
the skb->tail pointer maintained by skb_put/skb_trim is not relevant
to what happens when the skb_fill_page_desc function is called. This
issue was raised without comment in linux-kernel and netdev earlier
this month:
http://thread.gmane.org/gmane.linux.kernel/446474/http://thread.gmane.org/gmane.linux.network/45444/
So until there is something analogous to skb_put that works for
zero-copy write skbuffs, we will do what the other callers of
skb_fill_page_desc are doing.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The NARGS enum is left over from older code versions.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the copyright year to 2006.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This message doesn't help users because the circumstance isn't problematic.
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before potentially fixing up these functions, this cosmetic change
reduces the indentation level to make the code easier to read and
maintain.
No functional changes at all.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as797) fixes device_add() in the driver core. It needs to
pay attention when the driver for a new device reports an error.
At the same time, since bus_remove_device() undoes the effects of both
bus_add_device() and bus_attach_device(), it needs to check whether
the bus_attach_device step failed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If kmalloc() fails to allocate space for 'old_symlink_name' in
drivers/base/core.c::device_rename(), then we'll leak 'old_class_name'.
Spotted by the Coverity checker.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return the return value of sysfs_create_group() in topology_add_dev().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check for device_create_file() return value in dma_pool_create().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check for return code of device_create_file() and correct cleanup in
the error case in device_add().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check return value of bus_add_attrs() in bus_register().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check for return value of sysfs_create_link() in class_device_add().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make dev_printk usable from non-GPL modules again
dev_printk now calls dev_driver_string. We want even proprietary modules
to be calling dev_printk, so the export of dev_driver_string needs to be
non-GPL-only.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure data is freed if the kthread fails to start.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes it possible to build pci hotplug drivers outside of the main
kernel tree, and Sam keeps telling me to move local header files to
their proper places...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a patch adding me to the maintainers file for the pci
hotplug subsystem, as we discussed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation. Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively. Many people have come to expect this naming. Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations). I also have reports that various Sun and HP servers
have similar behavior.
Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also). 2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.
On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1. If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.
A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.
-[0000:00]-+-00.0 Intel Corporation 5000P Chipset Memory Controller Hub
+-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
+-1c.0-[0000:01-02]----00.0-[0000:02]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)
Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.
Solution:
The solution can come in multiple steps.
Suggested fix#1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels. It adds two new
command line options:
pci=bfsort
pci=nobfsort
to force the sort order, or not, as you wish. It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".
Suggested fix#2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in. I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first. It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.
Suggested fix#3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order. This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers). I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.
Feedback appreciated. Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.
You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm. I think
that's both safe and appropriate in this instance.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cpcihp_generic module requires configured "bridge" module parameter.
But it can be loaded successfully without that parameter.
Because module init call ends up returning positive value.
This patch prevents from loading without setting "bridge" module parameter.
Signed-off-by: Akinbou Mita <akinobu.mita@gmail.com>
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to finish converting to pci_get_* interfaces we need to add a couple
of bits of missing functionaility
pci_get_bus_and_slot() provides the equivalent to pci_find_slot()
(pci_get_slot is already taken as a name for something similar but not the
same)
pci_get_device_reverse() is the equivalent of pci_find_device_reverse but
refcounting
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. ioremap must be balanced by an iounmap and failing to do so can
result in a memory leak.
2. Handle return value correctly
Tested (compilation only) with:
- allmodconfig
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unnecessary cmd_busy member from struct
controller. Read command status register instead of using cmd_busy.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that shpchp driver could mis-detect
command failures if the system was under heavy load.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_find is not hotplug safe, so it really doesn't want to be in an
actual hotplug driver either.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Thu, 2006-09-28 at 03:42, Olaf Hering wrote:
> PCI-Express AER implemetation: pcie_portdrv error handler
>
> This patch breaks if CONFIG_PM is not enabled,
> pcie_portdrv_restore_config() will be undefined.
I move the definition of pcie_portdrv_restore_config
out of CONFIG_PM.
Below patch is against 2.6.18-mm1. Could you try it?
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ACPIPnP implementation had the understanding of Linux resource flags very
wrong, resulting in a nonfunctional implementation of DMA resource
allocation.
This was usually not a problem, since almost no on-board PnP devices use ISA
DMA, with the exception of ECP parallel ports. Even with that, parallel port
DMA is preconfigured by the BIOS, so this routine isn't normally called.
Except in the case where somebody does 'rmmod parport_pc; modprobe
parport_pc', where the rmmod case disables the ECP parallel port resources,
and they need to be enabled again to initialize the module. This didn't
work, resulting in a non-printing printer.
The application doing exactly the above to force reprobing of printers is
the YaST printer module. Thus without this fix YaST wedged the printer when
configuring it, and was not able to print a test page.
Reported-by: Ralf Flaxa <rf@suse.de>
Reproduced-by: Jiri Dluhos <jdluhos@suse.cz>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_fixup_video turns into generic code because there are many platforms need this fixup
for embedded VGA as well as x86. The Video BIOS integrates into System BIOS on a machine
has embedded VGA although embedded VGA generally don't have PCI ROM. As a result,
embedded VGA need the way that the sysfs rom points to the Video BIOS of System
RAM (0xC0000). PCI-to-PCI Bridge Architecture specification describes the condition whether
or not PCI ROM forwards VGA compatible memory address. fixup_video suits this specification.
Although the Video ROM generally implements in x86 code regardless of platform, some
application such as X Window System can run this code by dosemu86. Therefore,
pci_fixup_video should turn into generic code.
Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__must_check goes on the declaration, not the definition.
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The most recent VIA IRQ quirk changes have broken various VIA devices for
some users. We are not able to add these devices to the blacklist as they
are also available in PCI-card form, and running the quirk on these devices
brings us back to square one (running the VIA quirk on non-VIA boards where
the quirk is not needed).
This patch, based on suggestions from Sergey Vlasov, implements a scheme
similar to but more restrictive than the scheme we had in 2.6.16 and
earlier. It runs the quirk on all VIA hardware, but *only* if a VIA
southbridge was detected on the system.
To further reduce the amount of quirked devices, this patch includes a
change suggested by Linus at http://lkml.org/lkml/2005/9/27/113 This
ensures that devices bound to non-legacy IO-APIC interrupt lines are not
quirked. We have made one change to Linus' suggestion: we do a comparison
of ">15" rather than ">=15", as 15 is still in the legacy interrupt range.
There is still a downside to this patch: if the user inserts a VIA PCI card
into a VIA-based motherboard, in some circumstances the quirk will also run
on the VIA PCI card. This corner case is hard to avoid.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this was spotted by coverity (cid #819). We dereference p_slot
earlier in the function, and i found no way it could become NULL
anywhere.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that system will panic if multiple power
on/off operations are issued to the same slot in parallel. This
problem can be easily reproduced by commands below.
# while true; do echo 1 > power; echo 0 > power; done &
# while true; do echo 1 > power; echo 0 > power; done &
The cause is lack of locking for enable/disable operations. This patch
fixes this problem.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The slot number displayed in info messages would cause a confusion
because those are displayed in several ways (decimal and hex).
Furthermore, those slot number is not same as slot name (directory
name). This patch fixes those improper info messages.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that issuing SHPC command in poll mode
always fails with the following message.
shpchp: Command not completed in 2000 msec
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up dasd timer when when a dasd device is set offline.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reset device operational notification flag when channel paths become
unavailable during path verification.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
