This patch updates defconfig using savedefconfig on Linux-4.19. It is
intended to have no functional change.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This tag contains the follow-on patches I'd like to target for the 4.20
merge window. I'm being somewhat conservative here, as while there are
a few patches on the mailing list that were posted early in the merge
window I'd like to let those bake for another round -- this was a fairly
big release as far as RISC-V is concerened, and we need to walk before
we can run.
As far as the patches that made it go:
* A patch to ignore offline CPUs when calculating AT_HWCAP. This should
fix GDB on the HiFive unleashed, which has an embedded core for hart
0 which is exposed to Linux as an offline CPU.
* A move of EM_RISCV to elf-em.h, which is where it should have been to
begin with.
* I've also removed the 64-bit divide routines. I know I'm not really
playing by my own rules here because I posted the patches this
morning, but since they shouldn't be in the kernel I think it's better
to err on the side of going too fast here.
I don't anticipate any more patch sets for the merge window.
Changes since v1:
* Use a consistent base to merge from so the history isn't a mess.
-----BEGIN PGP SIGNATURE-----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=9Lsg
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.20-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull more RISC-V updates from Palmer Dabbelt:
"This contains the follow-on patches I'd like to target for the 4.20
merge window. I'm being somewhat conservative here, as while there are
a few patches on the mailing list that were posted early in the merge
window I'd like to let those bake for another round -- this was a
fairly big release as far as RISC-V is concerened, and we need to walk
before we can run.
As far as the patches that made it go:
- A patch to ignore offline CPUs when calculating AT_HWCAP. This
should fix GDB on the HiFive unleashed, which has an embedded core
for hart 0 which is exposed to Linux as an offline CPU.
- A move of EM_RISCV to elf-em.h, which is where it should have been
to begin with.
- I've also removed the 64-bit divide routines. I know I'm not really
playing by my own rules here because I posted the patches this
morning, but since they shouldn't be in the kernel I think it's
better to err on the side of going too fast here.
I don't anticipate any more patch sets for the merge window"
* tag 'riscv-for-linus-4.20-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
Move EM_RISCV into elf-em.h
RISC-V: properly determine hardware caps
Revert "lib: Add umoddi3 and udivmoddi4 of GCC library routines"
Revert "RISC-V: Select GENERIC_LIB_UMODDI3 on RV32"
These were only necessary for an out-of-tree driver that has since been
fixed to use the proper divide routines. I've simply reverted the pair
of commits we made last week.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This should never have been inside our arch port to begin with, it's
just a relic from when we were maintaining out of tree patches.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
On the Hifive-U platform, cpu 0 is a masked cpu with less capabilities
than the other cpus. Ignore it for the purpose of determining the
hardware capabilities of the system.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
I'm removing the generic 64-bit divide support, which means this will no
longer work.
This reverts commit 757331db92.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architecures use memblock for early memory management. There is no need
for the CONFIG_HAVE_MEMBLOCK configuration option.
[rppt@linux.vnet.ibm.com: of/fdt: fixup #ifdefs]
Link: http://lkml.kernel.org/r/20180919103457.GA20545@rapoport-lnx
[rppt@linux.vnet.ibm.com: csky: fixups after bootmem removal]
Link: http://lkml.kernel.org/r/20180926112744.GC4628@rapoport-lnx
[rppt@linux.vnet.ibm.com: remove stale #else and the code it protects]
Link: http://lkml.kernel.org/r/1538067825-24835-1-git-send-email-rppt@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1536927045-23536-4-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All achitectures select NO_BOOTMEM which essentially becomes 'Y' for any
kernel configuration and therefore it can be removed.
[alexander.h.duyck@linux.intel.com: remove now defunct NO_BOOTMEM from depends list for deferred init]
Link: http://lkml.kernel.org/r/20180925201814.3576.15105.stgit@localhost.localdomain
Link: http://lkml.kernel.org/r/1536927045-23536-3-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prefer _THIS_IP_ defined in linux/kernel.h.
Most definitions of current_text_addr were the same as _THIS_IP_, but
a few archs had inline assembly instead.
This patch removes the final call site of current_text_addr, making all
of the definitions dead code.
[akpm@linux-foundation.org: fix arch/csky/include/asm/processor.h]
Link: http://lkml.kernel.org/r/20180911182413.180715-1-ndesaulniers@google.com
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch set contains a lot (at least, for me) of improvements to the
RISC-V kernel port:
* The removal of some cacheinfo values that were bogus.
* On systems with F but without D the kernel will not show the F
extension to userspace, as it isn't actually supported.
* Support for futexes.
* Removal of some unused code.
* Cleanup of some menuconfig entries.
* Support for systems without a floating-point unit, and for building
kernels that will never use the floating-point unit.
* More fixes to the RV32I port, which regressed again. It's really time
to get this into a regression test somewhere so I stop breaking it.
Thanks to Zong for resurrecting it again!
* Various fixes that resulted from a year old review of our original
patch set that I finally got around to.
* Various improvements to SMP support, largely based around having
switched to logical hart numbering, as well as some interrupt
improvements. This one is in the same patch set as above, thanks to
Atish for sheparding everything though as my patch set was a bit of a
mess.
I'm pretty sure this is our largest patch set since the original kernel
contribution, and it's certainly the one with the most contributors.
While I don't have anything else I know I'm going to submit for the
merge window, I would be somewhat surprised if I didn't screw anything
up.
Thanks for the help, everyone!
-----BEGIN PGP SIGNATURE-----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=YL+A
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This patch set contains a lot (at least, for me) of improvements to
the RISC-V kernel port:
- The removal of some cacheinfo values that were bogus.
- On systems with F but without D the kernel will not show the F
extension to userspace, as it isn't actually supported.
- Support for futexes.
- Removal of some unused code.
- Cleanup of some menuconfig entries.
- Support for systems without a floating-point unit, and for building
kernels that will never use the floating-point unit.
- More fixes to the RV32I port, which regressed again. It's really
time to get this into a regression test somewhere so I stop
breaking it. Thanks to Zong for resurrecting it again!
- Various fixes that resulted from a year old review of our original
patch set that I finally got around to.
- Various improvements to SMP support, largely based around having
switched to logical hart numbering, as well as some interrupt
improvements. This one is in the same patch set as above, thanks to
Atish for sheparding everything though as my patch set was a bit of
a mess.
I'm pretty sure this is our largest patch set since the original
kernel contribution, and it's certainly the one with the most
contributors. While I don't have anything else I know I'm going to
submit for the merge window, I would be somewhat surprised if I didn't
screw anything up.
Thanks for the help, everyone!"
* tag 'riscv-for-linus-4.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits)
RISC-V: Cosmetic menuconfig changes
riscv: move GCC version check for ARCH_SUPPORTS_INT128 to Kconfig
RISC-V: remove the unused return_to_handler export
RISC-V: Add futex support.
RISC-V: Add FP register ptrace support for gdb.
RISC-V: Mask out the F extension on systems without D
RISC-V: Don't set cacheinfo.{physical_line_partition,attributes}
RISC-V: Show IPI stats
RISC-V: Show CPU ID and Hart ID separately in /proc/cpuinfo
RISC-V: Use Linux logical CPU number instead of hartid
RISC-V: Add logical CPU indexing for RISC-V
RISC-V: Use WRITE_ONCE instead of direct access
RISC-V: Use mmgrab()
RISC-V: Rename im_okay_therefore_i_am to found_boot_cpu
RISC-V: Rename riscv_of_processor_hart to riscv_of_processor_hartid
RISC-V: Provide a cleaner raw_smp_processor_id()
RISC-V: Disable preemption before enabling interrupts
RISC-V: Comment on the TLB flush in smp_callin()
RISC-V: Filter ISA and MMU values in cpuinfo
RISC-V: Don't set cacheinfo.{physical_line_partition,attributes}
...
Pull timekeeping updates from Thomas Gleixner:
"The timers and timekeeping departement provides:
- Another large y2038 update with further preparations for providing
the y2038 safe timespecs closer to the syscalls.
- An overhaul of the SHCMT clocksource driver
- SPDX license identifier updates
- Small cleanups and fixes all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
tick/sched : Remove redundant cpu_online() check
clocksource/drivers/dw_apb: Add reset control
clocksource: Remove obsolete CLOCKSOURCE_OF_DECLARE
clocksource/drivers: Unify the names to timer-* format
clocksource/drivers/sh_cmt: Add R-Car gen3 support
dt-bindings: timer: renesas: cmt: document R-Car gen3 support
clocksource/drivers/sh_cmt: Properly line-wrap sh_cmt_of_table[] initializer
clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines
clocksource/drivers/sh_cmt: Fixup for 64-bit machines
clocksource/drivers/sh_tmu: Convert to SPDX identifiers
clocksource/drivers/sh_mtu2: Convert to SPDX identifiers
clocksource/drivers/sh_cmt: Convert to SPDX identifiers
clocksource/drivers/renesas-ostm: Convert to SPDX identifiers
clocksource: Convert to using %pOFn instead of device_node.name
tick/broadcast: Remove redundant check
RISC-V: Request newstat syscalls
y2038: signal: Change rt_sigtimedwait to use __kernel_timespec
y2038: socket: Change recvmmsg to use __kernel_timespec
y2038: sched: Change sched_rr_get_interval to use __kernel_timespec
y2038: utimes: Rework #ifdef guards for compat syscalls
...
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
This patch series now has evolved to contain several related changes.
1. Updated the assorted cleanup series by Palmer.
The original cleanup patch series can be found here.
http://lists.infradead.org/pipermail/linux-riscv/2018-August/001232.html
2. Implemented decoupling linux logical CPU ids from hart id.
Some of the work has been inspired from ARM64.
Tested on QEMU & HighFive Unleashed board with/without SMP enabled.
3. Included Anup's cleanup and IPI stat patch.
All the patch series have been combined to avoid conflicts as a lot of
common code is changed different patch sets. Atish has mostly addressed
review comments and fixed checkpatch errors from Palmer's and Anup's
series.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch set fixes up various failures in the RV32I port. The fixes
are all nominally independent, but are really only testable together
because the RV32I port fails to build without all of them. The patch
set includes:
* The removal of tishift on RV32I targets, as 128-bit integers are not
supported by the toolchain.
* The removal of swiotlb from RV32I targets, since all physical
addresses can be mapped by all hardware on all existing RV32I targets.
* The addition of ummodi3 and udivmoddi4 from an old version of GCC that
was licensed under GPLv2 as generic code, along with their use on
RV32I targets.
* A fix to our page alignment logic within ioremap for RV32I targets.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patchset adds an option, CONFIG_FPU, to enable/disable floating-
point support within the kernel. The kernel's new behavior will be as
follows:
* with CONFIG_FPU=y
All FPU codes are reserved. If no FPU is found during booting, a
global flag will be set, and those functions will be bypassed with
condition check to that flag.
* with CONFIG_FPU=n
No floating-point instructions in kernel and all related settings
are excluded.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
* Move the built-in cmdline configuration on a new menu entry "Boot
options", it doesn't make much sense to be part of the debuging menu.
* Rename "Kernel Type" menu to "Kernel features" to be more consistent with
what other architectures are using, plus "type" is a bit misleading here.
Signed-off-by: Nick Kossifidis <mick@ics.forth.gr>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This export is not only not needed, but also breaks symbol versioning
due to being an undeclared assembly export.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Here is an attempt to add the missing futex support. I started with the MIPS
version of futex.h and modified it until I got it working. I tested it on
a HiFive Unleashed running Fedora Core 29 using the fc29 4.15 version of the
kernel. This was tested against the glibc testsuite, where it fixes 14 nptl
related testsuite failures. That unfortunately only tests the cmpxchg support,
so I also used the testcase at the end of
https://lwn.net/Articles/148830/
which tests the atomic_op functionality, except that it doesn't verify that
the operations are atomic, which they obviously are. This testcase runs
successfully with the patch and fails without it.
I'm not a kernel expert, so there could be details I got wrong here. I wasn't
sure about the memory model support, so I used aqrl which seemed safest, and
didn't add fences which seemed unnecessary. I'm not sure about the copyright
statements, I left in Ralf Baechle's line because I started with his code.
Checkpatch reports some style problems, but it is the same style as the MIPS
futex.h, and the uses of ENOSYS appear correct even though it complains about
them. I don't know if any of that matters.
This patch was tested on qemu with the glibc nptl/tst-cond-except
testcase, and the wake_op testcase from above.
Signed-off-by: Jim Wilson <jimw@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add a variable and a macro to describe FP registers, assuming only D is
supported. FP code is conditional on CONFIG_FPU. The FP regs and FCSR
are copied separately to avoid copying struct padding. Tested by hand and
with the gdb testsuite.
Signed-off-by: Jim Wilson <jimw@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The RISC-V Linux port doesn't support systems that have the F extension
but don't have the D extension -- we actually don't support systems
without D either, but Alan's patch set is rectifying that soon. For now
I think we can leave this in a semi-broken state and just wait for
Alan's patch set to get merged for proper non-FPU support -- the patch
set is starting to look good, so doing something in-between doesn't seem
like it's worth the work.
I don't think it's worth fretting about support for systems with F but
not D for now: our glibc ABIs are IMAC and IMAFDC so they probably won't
end up being popular. We can always extend this in the future.
CC: Alan Kao <alankao@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
These are just hard coded in the RISC-V port, which doesn't make any
sense. We should probably be setting these from device tree entries
when they exist, but for now I think it's saner to just leave them all
as their default values.
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch provides arch_show_interrupts() implementation to
show IPI stats via /proc/interrupts.
Now the contents of /proc/interrupts" will look like below:
CPU0 CPU1 CPU2 CPU3
8: 17 7 6 14 SiFive PLIC 8 virtio0
10: 10 10 9 11 SiFive PLIC 10 ttyS0
IPI0: 170 673 251 79 Rescheduling interrupts
IPI1: 1 12 27 1 Function call interrupts
Signed-off-by: Anup Patel <anup@brainfault.org>
[Atish - Fixed checkpatch errors]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Changes since v2:
- Remove use of IPI_CALL_WAKEUP because it's being removed
Changes since v1:
- Add stub inline show_ipi_stats() function for !CONFIG_SMP
- Make ipi_names[] dynamically sized at compile time
- Minor beautification of ipi_names[] using tabs
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, /proc/cpuinfo show logical CPU ID as Hart ID which
is in-correct. This patch shows CPU ID and Hart ID separately
in /proc/cpuinfo using cpuid_to_hardid_map().
With this patch, contents of /proc/cpuinfo looks as follows:
processor : 0
hart : 1
isa : rv64imafdc
mmu : sv48
processor : 1
hart : 0
isa : rv64imafdc
mmu : sv48
processor : 2
hart : 2
isa : rv64imafdc
mmu : sv48
processor : 3
hart : 3
isa : rv64imafdc
mmu : sv48
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Setup the cpu_logical_map during boot. Moreover, every SBI call
and PLIC context are based on the physical hartid. Use the logical
CPU to hartid mapping to pass correct hartid to respective functions.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, both Linux CPU id and hart id are same.
This is not recommended as it will lead to discontinuous CPU
indexing in Linux. Moreover, kdump kernel will run from CPU0
which would be absent if we follow existing scheme.
Implement a logical mapping between Linux CPU id and hart
id to decouple these two. Always mark the boot processor as
CPU0 and all other CPUs get the logical CPU id based on their
booting order.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The secondary harts spin on couple of per cpu variables until both of
these are non-zero so it's not necessary to have any ordering here.
However, WRITE_ONCE should be used to avoid tearing.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
commit f1f1007644 ("mm: add new mmgrab() helper") added a
helper that we missed out on.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The old name was a bit odd.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It's a bit confusing exactly what this function does: it actually
returns the hartid of an OF processor node, failing with -1 on invalid
nodes. I've changed the name to _hartid() in order to make that a bit
more clear, as well as adding a comment.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
I'm not sure how I managed to miss this the first time, but this is much
better.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: code comment formatting and other fixes]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, irq is enabled before preemption disabling happens.
If the scheduler fired right here and cpu is scheduled then it
may blow up.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: Commit text and code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We shouldn't be directly passing device tree values to userspace, both
because there could be mistakes in device trees and because the kernel
doesn't support arbitrary ISAs.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: checkpatch fix and code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
These are just hard coded in the RISC-V port, which doesn't make any
sense. We should probably be setting these from device tree entries
when they exist, but for now I think it's saner to just leave them all
as their default values.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The scause is already part of pt_regs so no need to pass
scause as separate arg to do_IRQ().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
For 32bit, the upper 32-bit of phys_addr_t will be flushed to zero
after AND with PAGE_MASK because the data type of PAGE_MASK is
unsigned long. To fix this problem, the page alignment is done by
subtracting the page offset instead of AND with PAGE_MASK.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Only RV64 supports swiotlb. On RV32, it don't select the SWIOTLB.
Signed-off-by: Zong Li <zong@andestech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We expect that a kernel with CONFIG_FPU=y can still support no-FPU
machines. To do so, the kernel should first examine the existence of a
FPU, then do nothing if a FPU does exist; otherwise, it should
disable/bypass all FPU-related functions.
In this patch, a new global variable, has_fpu, is created and determined
when parsing the hardware capability from device tree during booting.
This variable is used in those FPU-related functions.
Signed-off-by: Alan Kao <alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Vincent Chen <vincentc@andestech.com>
Cc: Zong Li <zong@andestech.com>
Cc: Nick Hu <nickhu@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
FPU codes have been separated from common part in previous patches.
This patch add the CONFIG_FPU option and some stubs, so that a no-FPU
configuration is allowed.
Signed-off-by: Alan Kao <alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Vincent Chen <vincentc@andestech.com>
Cc: Zong Li <zong@andestech.com>
Cc: Nick Hu <nickhu@andestech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch cleanup the MARCH string passing to both compiler and
assembler. Note that the CFLAGS should not contain "fd" before we
have mechnisms like kernel_fpu_begin/end in other architectures.
Signed-off-by: Alan Kao <alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Vincent Chen <vincentc@andestech.com>
Cc: Zong Li <zong@andestech.com>
Cc: Nick Hu <nickhu@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
FPU-related logic is separated from normal signal handling path in
this patch. Kernel can easily be configured to exclude those procedures
for no-FPU systems.
Signed-off-by: Alan Kao <alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Vincent Chen <vincentc@andestech.com>
Cc: Zong Li <zong@andestech.com>
Cc: Nick Hu <nickhu@andestech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We move __fstate_save and __fstate_restore to a new source
file, fpu.S.
Signed-off-by: Alan Kao <alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Vincent Chen <vincentc@andestech.com>
Cc: Zong Li <zong@andestech.com>
Cc: Nick Hu <nickhu@andestech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Rework the defintion of struct siginfo so that the array padding
struct siginfo to SI_MAX_SIZE can be placed in a union along side of
the rest of the struct siginfo members. The result is that we no
longer need the __ARCH_SI_PREAMBLE_SIZE or SI_PAD_SIZE definitions.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Use memblock_end_of_DRAM which provides correct last low memory
PFN. Without that, DMA32 region becomes empty resulting in zero
pages being allocated for DMA32.
This patch is based on earlier patch from palmer which never
merged into 4.19. I just edited the commit text to make more
sense.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Building a riscv kernel with CONFIG_FUNCTION_TRACER and
CONFIG_MODVERSIONS enabled results in these two warnings:
MODPOST vmlinux.o
WARNING: EXPORT symbol "return_to_handler" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "_mcount" [vmlinux] version generation failed, symbol will not be versioned.
When exporting symbols from an assembly file, the MODVERSIONS code
requires their prototypes to be defined in asm-prototypes.h (see
scripts/Makefile.build). Since both of these symbols have prototypes
defined in linux/ftrace.h, include this header from RISC-V's
asm-prototypes.h.
Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: James Cowgill <jcowgill@debian.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
