nf_conntrack_h323 needs ip6_route_output for the call forwarding filter.
Add a ->route function to nf_afinfo and use that to avoid pulling in the
ipv6 module.
Fix the #ifdef for the IPv6 code while I'm at it - the IPv6 support is
only needed when IPv6 conntrack is enabled.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rate estimator match. The rate estimator match can match on
estimated rates by the RATEEST target. It supports matching on
absolute bps/pps values, comparing two rate estimators and matching
on the difference between two rate estimators.
This is what I use to route outgoing data connections from a FTP
server over two lines based on the available bandwidth:
# estimate outgoing rates
iptables -t mangle -A POSTROUTING -o eth0 -j RATEEST --rateest-name eth0 \
--rateest-interval 250ms \
--rateest-ewma 0.5s
iptables -t mangle -A POSTROUTING -o ppp0 -j RATEEST --rateest-name ppp0 \
--rateest-interval 250ms \
--rateest-ewma 0.5s
# mark based on available bandwidth
iptables -t mangle -A BALANCE -m state --state NEW \
-m helper --helper ftp \
-m rateest --rateest-delta \
--rateest1 eth0 \
--rateest-bps1 2.5mbit \
--rateest-gt \
--rateest2 ppp0 \
--rateest-bps2 2mbit \
-j CONNMARK --set-mark 0x1
iptables -t mangle -A BALANCE -m state --state NEW \
-m helper --helper ftp \
-m rateest --rateest-delta \
--rateest1 ppp0 \
--rateest-bps1 2mbit \
--rateest-gt \
--rateest2 eth0 \
--rateest-bps2 2.5mbit \
-j CONNMARK --set-mark 0x2
iptables -t mangle -A BALANCE -j CONNMARK --restore-mark
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new rate estimator target (using gen_estimator). In combination with
the rateest match (next patch) this can be used for load-based multipath
routing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends the xt_DSCP target by xt_TOS v1 to add support for selectively
setting and flipping any bit in the IPv4 TOS and IPv6 Priority fields.
(ipt_TOS and xt_DSCP only accepted a limited range of possible
values.)
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends the xt_dscp match by xt_tos v1 to add support for selectively
matching any bit in the IPv4 TOS and IPv6 Priority fields. (ipt_tos
and xt_dscp only accepted a limited range of possible values.)
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Constify include/net/dsfield.h
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addrtype match has a new revision (1), which lets address type checking
limited to the interface the current packet belongs to. Either incoming
or outgoing interface can be used depending on the current hook. In the
FORWARD hook two maches should be used if both interfaces have to be checked.
The new structure is ipt_addrtype_info_v1.
Revision 0 lets older userspace programs use the match as earlier.
ipt_addrtype_info is used.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Address type search can be limited to an interface by
inet_dev_addr_type function.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
xt_owner merges ipt_owner and ip6t_owner, and adds a flag to match
on socket (non-)existence.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a big array of NR_CPUS entries, we can compute the size
needed at runtime, using nr_cpu_ids
This should save some ram (especially on David's machines where NR_CPUS=4096 :
32 KB can be saved per table, and 64KB for dynamically allocated ones (because
of slab/slub alignements) )
In particular, the 'bootstrap' tables are not any more static (in data
section) but on stack as their size is now very small.
This also should reduce the size used on stack in compat functions
(get_info() declares an automatic variable, that could be bigger than kernel
stack size for big NR_CPUS)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Schnelle <svens@bitebene.org>
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch speedups compilation when net_namespace.h is changed.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When merging the input paths of IPsec I accidentally left a hard-coded
AF_INET for the state lookup call. This broke IPv6 obviously. This
patch fixes by getting the input callers to specify the family through
skb->cb.
Credit goes to Kazunori Miyazawa for diagnosing this and providing an
initial patch.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointing to the next skb is necessary to avoid referencing
already SACKed skbs which will soon be on a separate list.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures the 802.11n mode of operation
internally in ieee80211_conf structure and in the low-level
driver as well (through op conf_ht).
It does not include AP configuration flows.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New structures:
- ieee80211_ht_info: describing STA's HT capabilities
- ieee80211_ht_bss_info: describing BSS's HT characteristics
Changed structures:
- ieee80211_hw_mode: now also holds PHY HT capabilities for each HW mode
- ieee80211_conf: ht_conf holds current self HT configuration
ht_bss_conf holds current BSS HT configuration
- flag IEEE80211_CONF_SUPPORT_HT_MODE added to indicate if HT use is
desired
- sta_info: now also holds Peer's HT capabilities
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interface iteration in mac80211 can be done without holding any
locks because I converted it to RCU. Initially, I thought this
wouldn't be needed for ieee80211_iterate_active_interfaces but
it's turning out that multi-BSS AP support can be much simpler
in a driver if ieee80211_iterate_active_interfaces can be called
without holding locks. This converts it to use RCU, it adds a
requirement that the callback it invokes cannot sleep.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the core.
* add the ctl_table_header on the struct net;
* make the unix_sysctl_register and _unregister clone the table;
* moves calls to them into per-net init and exit callbacks;
* move the .data pointer in the proper place.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will make all the sub-namespaces always use the
default value (10) and leave the tuning via sysctl
to the init namespace only.
Per-namespace tuning is coming.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the struct net * argument to both of them to use in
the future. Also make the register one return an error code.
It is useless right now, but will make the future patches
much simpler.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user interface is: register_net_sysctl_table and
unregister_net_sysctl_table. Very much like the current
interface except there is a network namespace parameter.
With this any sysctl registered with register_net_sysctl_table
will only show up to tasks in the same network namespace.
All other sysctls continue to be globally visible.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the basic infrastructure for per namespace sysctls.
A list of lists of sysctl headers is added, allowing each namespace to have
it's own list of sysctl headers.
Each list of sysctl headers has a lookup function to find the first
sysctl header in the list, allowing the lists to have a per namespace
instance.
register_sysct_root is added to tell sysctl.c about additional
lists of sysctl_headers. As all of the users are expected to be in
kernel no unregister function is provided.
sysctl_head_next is updated to walk through the list of lists.
__register_sysctl_paths is added to add a new sysctl table on
a non-default sysctl list.
The only intrusive part of this patch is propagating the information
to decided which list of sysctls to use for sysctl_check_table.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
By doing this we allow users of register_sysctl_paths that build
and dynamically allocate their ctl_table to be simpler. This allows
them to just remember the ctl_table_header returned from
register_sysctl_paths from which they can now find the
ctl_table array they need to free.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a number of modules that register a sysctl table
somewhere deeply nested in the sysctl hierarchy, such as
fs/nfs, fs/xfs, dev/cdrom, etc.
They all specify several dummy ctl_tables for the path name.
This patch implements register_sysctl_path that takes
an additional path name, and makes up dummy sysctl nodes
for each component.
This patch was originally written by Olaf Kirch and
brought to my attention and reworked some by Olaf Hering.
I have changed a few additional things so the bugs are mine.
After converting all of the easy callers Olaf Hering observed
allyesconfig ARCH=i386, the patch reduces the final binary size by 9369 bytes.
.text +897
.data -7008
text data bss dec hex filename
26959310 4045899 4718592 35723801 2211a19 ../vmlinux-vanilla
26960207 4038891 4718592 35717690 221023a ../O-allyesconfig/vmlinux
So this change is both a space savings and a code simplification.
CC: Olaf Kirch <okir@suse.de>
CC: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the defines again, convert to the new checksum helper names and
remove the dependency of NET_ACT_NAT on NETFILTER.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to get rid of the CONFIG_NETFILTER dependency of NET_ACT_NAT.
This patch redefines the old names to keep the noise low, the next patch
converts all users.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary state transitions for the two forms of passive-close
* PASSIVE_CLOSE - which is entered when a host receives a Close;
* PASSIVE_CLOSEREQ - which is entered when a client receives a CloseReq.
Here is a detailed account of what the patch does in each state.
1) Receiving CloseReq
The pseudo-code in 8.5 says:
Step 13: Process CloseReq
If P.type == CloseReq and S.state < CLOSEREQ,
Generate Close
S.state := CLOSING
Set CLOSING timer.
This means we need to address what to do in CLOSED, LISTEN, REQUEST, RESPOND, PARTOPEN, and OPEN.
* CLOSED: silently ignore - it may be a late or duplicate CloseReq;
* LISTEN/RESPOND: will not appear, since Step 7 is performed first (we know we are the client);
* REQUEST: perform Step 13 directly (no need to enqueue packet);
* OPEN/PARTOPEN: enter PASSIVE_CLOSEREQ so that the application has a chance to process unread data.
When already in PASSIVE_CLOSEREQ, no second CloseReq is enqueued. In any other state, the CloseReq is ignored.
I think that this offers some robustness against rare and pathological cases: e.g. a simultaneous close where
the client sends a Close and the server a CloseReq. The client will then be retransmitting its Close until it
gets the Reset, so ignoring the CloseReq while in state CLOSING is sane.
2) Receiving Close
The code below from 8.5 is unconditional.
Step 14: Process Close
If P.type == Close,
Generate Reset(Closed)
Tear down connection
Drop packet and return
Thus we need to consider all states:
* CLOSED: silently ignore, since this can happen when a retransmitted or late Close arrives;
* LISTEN: dccp_rcv_state_process() will generate a Reset ("No Connection");
* REQUEST: perform Step 14 directly (no need to enqueue packet);
* RESPOND: dccp_check_req() will generate a Reset ("Packet Error") -- left it at that;
* OPEN/PARTOPEN: enter PASSIVE_CLOSE so that application has a chance to process unread data;
* CLOSEREQ: server performed active-close -- perform Step 14;
* CLOSING: simultaneous-close: use a tie-breaker to avoid message ping-pong (see comment);
* PASSIVE_CLOSEREQ: ignore - the peer has a bug (sending first a CloseReq and now a Close);
* TIMEWAIT: packet is ignored.
Note that the condition of receiving a packet in state CLOSED here is different from the condition "there
is no socket for such a connection": the socket still exists, but its state indicates it is unusable.
Last, dccp_finish_passive_close sets either DCCP_CLOSED or DCCP_CLOSING = TCP_CLOSING, so that
sk_stream_wait_close() will wait for the final Reset (which will trigger CLOSING => CLOSED).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds two auxiliary states to deal with passive closes:
* PASSIVE_CLOSE (reached from OPEN via reception of Close) and
* PASSIVE_CLOSEREQ (reached from OPEN via reception of CloseReq)
as internal intermediate states.
These states are used to allow a receiver to process unread data before
acknowledging the received connection-termination-request (the Close/CloseReq).
Without such support, it will happen that passively-closed sockets enter CLOSED
state while there is still unprocessed data in the queue; leading to unexpected
and erratic API behaviour.
PASSIVE_CLOSE has been mapped into TCPF_CLOSE_WAIT, so that the code will
seamlessly work with inet_accept() (which tests for this state).
The state names are thanks to Arnaldo, who suggested this naming scheme
following an earlier revision of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes support for the Intra-Site Automatic Tunnel
Addressing Protocol (ISATAP) per RFC4214. It uses the SIT
module, and is configured using extensions to the "iproute2"
utility. The diffs are specific to the Linux 2.6.24-rc2 kernel
distribution.
This version includes the diff for ./include/linux/if.h which was
missing in the v2.4 submission and is needed to make the
patch compile. The patch has been installed, compiled and
tested in a clean 2.6.24-rc2 kernel build area.
Signed-off-by: Fred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3rd argument is always zero (according to grep :) Eliminate
it and merge the function with sk_stream_alloc_skb.
This saves 44 more bytes, and together with the previous patch
we have:
add/remove: 1/0 grow/shrink: 0/8 up/down: 183/-751 (-568)
function old new delta
sk_stream_alloc_skb - 183 +183
ip_rt_init 529 525 -4
arp_ignore 112 107 -5
__inet_lookup_listener 284 274 -10
tcp_sendmsg 2583 2481 -102
tcp_sendpage 1449 1300 -149
tso_fragment 417 258 -159
tcp_fragment 1149 988 -161
__tcp_push_pending_frames 1998 1837 -161
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function seems too big for inlining. Indeed, it saves
half-a-kilo when uninlined:
add/remove: 1/0 grow/shrink: 0/7 up/down: 195/-719 (-524)
function old new delta
sk_stream_alloc_pskb - 195 +195
ip_rt_init 529 525 -4
__inet_lookup_listener 284 274 -10
tcp_sendmsg 2583 2486 -97
tcp_sendpage 1449 1305 -144
tso_fragment 417 267 -150
tcp_fragment 1149 992 -157
__tcp_push_pending_frames 1998 1841 -157
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Better place exists in update_send_head (other non-queue related
adjustments are done there as well) which is the only caller of
tcp_advance_send_head (now that the bogus call from mtu_probe is
gone).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sock_wake_async() performs a bit different actions
depending on "how" argument. Unfortunately this argument
ony has numerical magic values.
I propose to give names to their constants to help people
reading this function callers understand what's going on
without looking into this function all the time.
I suppose this is 2.6.25 material, but if it's not (or the
naming seems poor/bad/awful), I can rework it against the
current net-2.6 tree.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I keep getting this build error and couldn't find anyone fixing
it in archives. ...Maybe all net developers except me build
just SMP kernels :-).
In file included from include/net/sock.h:50,
from ipc/mqueue.c:35:
include/linux/pcounter.h: In function 'pcounter_add':
include/linux/pcounter.h:87: error: 'struct pcounter' has no
member named 'value'
make[1]: *** [ipc/mqueue.o] Error 1
make: *** [ipc] Error 2
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This decouples PARTOPEN from TCP-specific stream-states.
It thus addresses the FIXME.
The code has been checked with regard to dependency on PARTOPEN and FIN_WAIT1
states (to which PARTOPEN previously was mapped): there is no difference, as
PARTOPEN is always referred to directly (i.e. not via the mapping to TCP
state).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This just generalises what was introduced by Eric Dumazet for the struct proto
inuse field in 286ab3d460:
[NET]: Define infrastructure to keep 'inuse' changes in an efficent SMP/NUMA way.
Please look at the comment in there to see the rationale.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds several structs and definitions to ieee80211.h
to support 802.11n draft specifications.
As 802.11n depends on and extends the 802.11e standard in several issues,
there are also several definitions that belong to 802.11e.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes drivers need to know which interfaces are associated with
their hardware. Rather than forcing those drivers to keep track of
the interfaces that were added, this adds an iteration function to
mac80211.
As it is intended to be used from the interface add/remove callbacks,
the iteration function may currently only be called under RTNL.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ipv6/raw.c and ipv4/raw.c use the seq files to walk
through the raw sockets hash and show them.
The "walking" code is rather huge, but is identical in both
cases. The difference is the hash table to walk over and
the protocol family to check (this was not in the first
virsion of the patch, which was noticed by YOSHIFUJI)
Make the ->open store the needed hash table and the family
on the allocated raw_iter_state and make the start/next/stop
callbacks work with it.
This removes most of the code.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as the ->hash one, this is easily consolidated.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the raw_hashinfo it's easy to consolidate the
raw[46]_hash functions.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4/raw.c and ipv6/raw.c contain many common code (most
of which is proc interface) which can be consolidated.
Most of the places to consolidate deal with the raw sockets
hashtable, so introduce a struct raw_hashinfo which describes
the raw sockets hash.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as in the previous patch for ipv4, compact the
API and hide hash table and rwlock inside the raw.c
file.
Plus fix some "bad" places from checkpatch.pl point
of view (assignments inside if()).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The raw sockets functions are explicitly used from
inside the kernel in two places:
1. in ip_local_deliver_finish to intercept skb-s
2. in icmp_error
For this purposes many functions and even data structures,
that are naturally internal for raw protocol, are exported.
Compact the API to two functions and hide all the other
(including hash table and rwlock) inside the net/ipv4/raw.c
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done by making packet_sklist_lock and packet_sklist per
network namespace and adding an additional filter condition on
received packets to ensure they came from the proper network
namespace.
Changes from v1:
- prohibit to call inet_dgram_ops.ioctl in other than init_net
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this patch none of the netlink callback support anything
except the initial network namespace but the rtnetlink infrastructure
now handles multiple network namespaces.
Changes from v2:
- IPv6 addrlabel processing
Changes from v1:
- no need for special rtnl_unlock handling
- fixed IPv6 ndisc
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
