The driver is still relying on internal OMAP IRQ defines that
are not relevant anymore if OMAP is built with SPARSE_IRQ.
Replace the defines with the proper IRQ base number.
Clean some comment style issue.
Remove some hidden and ugly cpu_class_is_omap1() inside the
gpio header.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Adapt the GPIO driver to retrieve information from a DT file.
Allocate the irq_base dynamically and rename bank->virtual_irq_start
to bank->irq_base.
Change irq_base type to int instead of u16 to match irq_alloc_descs
output.
Add documentation for GPIO properties specific to OMAP.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Replace the regular kzalloc and ioremap with the devm_ equivalent
to simplify error handling.
Add the missing devm_request_mem_region to reserve the region used
by the driver.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
The driver does not need anymore any id to identify the GPIO instance.
Remove every occurence of the bank->id inside the driver.
Remove two trailing spaces.
Add a dev variable for better readability in probe.
Remove unused variable bank->pbase.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
I've seen users getting very confused by the WARN_ON()s for can_sleep
GPIOs in the atomic-safe paths, the discoverability of the non-atomic
version of the API seems to be hampered by the fact that it's defined
in a header file not the .c file where the warnings are.
Add a couple of comments next to the warnings to help people on their
way.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding support for the open source gpio on which client
can specify the open source property through GPIO flag
GPIOF_OPEN_SOURCE at the time of gpio request.
The open source pins are normally pulled low and it
cannot be driven to output with value of 0 and so
when client request for setting the pin to LOW, the
gpio will be set to input direction to make pin in tristate
and hence PULL-DOWN on pins will make the state to LOW.
The open source pin can be driven to HIGH by setting output
with value of 1.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding support for the open drain gpio on which client
can specify the open drain property through GPIO flag
GPIOF_OPEN_DRAIN at the time of gpio request.
The open drain pins are normally pulled high and it
cannot be driven to output with value of 1 and so
when client request for setting the pin to HIGH, the
gpio will be set to input direction to make pin in tristate
and hence PULL-UP on pins will make the state to HIGH.
The open drain pin can be driven to LOW by setting output
with value of 0.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pl061 uses same routines for suspend/freeze/poweroff and resume/thaw/restore.
We are only saving and restoring register values on these routines.
During hibernation, in freeze() we take a snapshot of gpio registers. In thaw()
we don't actually need to restore these registers, as power was never shut down
till now. Similarly, in poweroff() we don't need to take snapshot of these
registers again, as it was done during freeze() and by now the image is already
saved on disk.
This patch passes poweroff() and thaw() routines as NULL to avoid this extra
work done.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts a number of the powerpc drivers to use the common library
of irq_domain xlate functions, dropping a bunch of lines in the process.
v5: - Remove tsi108 changes from patch
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Each revmap type has different arguments for setting up the revmap.
This patch splits up the generator functions so that each revmap type
can do its own setup and the user doesn't need to keep track of how
each revmap type handles the arguments.
This patch also adds a host_data argument to the generators. There are
cases where the host_data pointer will be needed before the function returns.
ie. the legacy map calls the .map callback for each irq before returning.
v2: - Add void *host_data argument to irq_domain_add_*() functions
- fixed failure to compile
- Moved IRQ_DOMAIN_MAP_* defines into irqdomain.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
GPIO IP revisions such as those used in OMAP4 have a set_dataout
while the previous revisions used a single dataout register.
Depending on what is available restore the dataout settings
to the right register.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setup the dataout register before restoring OE. This is to make
sure that we have valid data in dataout register which would be
made available in output pins as soon as OE is enabled. Else,
there is risk of unknown data getting out into gpio pins.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setup the interrupt enable registers only after we have configured the
required edge and required configurations, not before, to prevent
spurious events as part of restore routine.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
GPIO debounce registers need to be saved and restored for proper functioning
of driver.
Signed-off-by: Nishanth Menon <nm@ti.com>
tarun.kanti@ti.com: Debounce context save is moved to _set_gpio_debounce()
as part of dynamic context save to remove overhead.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Context is now saved dynamically in respective functions whenever and
whichever registers are modified. This avoid overhead of saving all
registers context in the runtime suspend callback.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Enable debounce clock before writing/reading debounce registers.
Disable the clock at the end so that it is synchronized with the
pm_runtime_get/put_sync calls.
Enable debounce clock per module. This call is mandatory because
in omap_gpio_request() when *_runtime_get_sync() is called,
_gpio_dbck_enable() within runtime callbck fails to turn on dbck
because dbck_enable_mask used within _gpio_dbck_enable() is still
not initialized at that point. Therefore we have to enable dbck here.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The dbck_enable_mask indicates which all GPIOs within a bank have debounce
enabled and dbck is enabled/disabled based upon this. But there is no
mechanism to track the dbck state. In order to manage the dbck state we need
additional flag and logic so that turning off/on dbck is synchronized with
pm_runtime_put/get_sync calls.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since *_prepare_for_idle() and *_resume_after_idle() are called
with interrupts disabled they should be kept as simple as possible.
So, moving most of the stuff to *_runtime_suspend/resume() callbacks.
To avoid invalid context restore happening in *_runtime_resume()
callback as a result of *_get_sync() call in *_gpio_probe(), update
bank->context_loss_count. This would make context restore condition
check false in the callback and skip restore until further
initialization take place. The workaround_enabled static variable
is now a member of struct gpio_bank.
Unlike most GPIO registers the OE has 0xffffffff as the default value.
To make sure invalid context is not restored, updating the OE context
with default value.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There is no need to operate on all the banks every time the function is called.
Just operate on the current bank passed by the framework.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Call runtime pm APIs pm_runtime_get_sync() and pm_runtime_put()
for enabling/disabling clocks appropriately. Remove syscore_ops and
instead use SET_RUNTIME_PM_OPS macro.
There is no more need to call omap_device_disable_idle_on_suspend
since driver is PM runtime adapted now.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.
mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove un-necessary bit masking. Since the register are 4 byte aligned
and readl would work as is. The 'enabled' mask is already taking care
to mask for bank width.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use regs->pinctrl field instead of using the macro OMAP1510_GPIO_PIN_CONTROL
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With register offsets now defined for respective OMAP versions we can get rid
of cpu_class_* checks. This function now has common initialization code for
all OMAP versions. Initialization specific to OMAP16xx has been moved within
omap16xx_gpio_init().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Getting rid of ifdefs within the function by adding register offset intctrl
and associating OMAPXXXX_GPIO_INT_CONTROL in respective SoC specific files.
Also, use wkup_status register consistently instead of referring to wakeup
clear and wakeup set register offsets. Get rid of cpu_is_xxxx checks in
set_gpio_trigger() using irqctrl.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently gpio_context array used to save gpio bank's context, is used only for
OMAP3 architecture. Move gpio_context as part of gpio_bank structure so that it
can be specific to each gpio bank and can be used for any OMAP architecture
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.
For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The device tps65910/tps65911 supports the sleep
functionality in some of gpios. If gpio is configured
in output mode and sleep is enabled then during device
sleep state, the output of gpio becomes LOW regardless
of non-sleep output value.
Such gpio can be used to control regulator switch such
that output of regulator is off in device sleep state.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Sodaville has GPIO controller behind the PCI bus. To my suprissed it is
not the same as on PXA.
The interrupt & gpio chip can be referenced from the device tree like
from any other driver. Unfortunately the driver which uses the gpio
interrupt has to use irq_of_parse_and_map() instead of
platform_get_irq(). The problem is that the platform device (which is
created from the device tree) is most likely created before the
interrupt chip is registered and therefore irq_of_parse_and_map() fails.
In theory the driver works as module. In reality most of the irq
functions are not exported to modules and it is possible that _this_
module is unloaded while the provided irqs are still in use.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
[torbenh@linutronix.de: make it work after the irq namespace cleanup,
add some device tree entries.]
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
[bigeasy@linutronix.de: convert to generic irq & gpio chip]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This bug was introduced by commit 54be5663
"gpio-ml-ioh: Support interrupt function" which adds a spinlock to struct
ioh_gpio but never init the spinlock.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This bug was introduced by commit d568a681
"gpio-pch: add spinlock in suspend/resume processing"
which adds a spinlock to struct pch_gpio but never init the spinlock.
Reported-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 15c9a0acc3 (of: create of_phandle_args to simplify return of phandle
parsing data) modifies the parameter list of of_xlate function pointer declaration
in gpio_chip. Adapt the gpio specifier translate function for this change.
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
we only use the gpio function of mc9s08dz60 mcu chip, so just
add the gpio driver, as this mcu will never be used in other board.
Signed-off-by: Wu Guoxing <b39297@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
One of the GPIO names in drivers/gpio/gpio-lpc32xx.c
was bad. Renaming gpi000 -> gpio00
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Using the correct gpio offset for setting the initial value
of gpio when setting output direction.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver does an unconditional read of io space during module init which
causes a bad dereference on ARM. It looks to me like this is an x86 only
drivers, so restrict it to only compile on x86.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Denis Turischev <denis@compulab.co.il>
The __iomem annotation is to be used together with pointers used
in iowrite32() but not for pointers returned by kzalloc().
For more details see [1] and [2].
This patch will remove the following sparse warning (i.e. when
copiling with "make C=1"):
* warning: incorrect type in assignment (different address spaces)
References:
[1] A new I/O memory access mechanism (Sep 15, 2004)
http://lwn.net/Articles/102232/
[2] Being more anal about iospace accesses (Sep 15, 2004)
http://lwn.net/Articles/102240/
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch will remove the following sparse warning ("make C=1"):
* warning: Using plain integer as NULL pointer
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
