This patch (as617) adds a couple of memory barriers that Ben H. forgot in
his recent suspend/resume fix.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch closes the IRQ race and makes various other OHCI & EHCI code
path safer vs. suspend/resume.
I've been able to (finally !) successfully suspend and resume various
Mac models, with or without USB mouse plugged, or plugging while asleep,
or unplugging while asleep etc... all without a crash.
Alan, please verify the UHCI bit I did, I only verified that it builds.
It's very simple so I wouldn't expect any issue there. If you aren't
confident, then just drop the hunks that change uhci-hcd.c
I also made the patch a little bit more "safer" by making sure the store
to the interrupt register that disables interrupts is not posted before
I set the flag and drop the spinlock.
Without this patch, you cannot reliably sleep/wakeup any recent Mac, and
I suspect PCs have some more sneaky issues too (they don't frankly crash
with machine checks because x86 tend to silently swallow PCI errors but
that won't last afaik, at least PCI Express will blow up in those
situations, but the USB code may still misbehave).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add .owner initialisation to the device drivers
in drivers/usb/host so that when built as module
the device_driver refers to the owning module
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as581) changes the assignments to hcd->state in the uhci-hcd
driver. It fixes part of bugzilla entry #5227. The problem was revealed
by David's large suite of USB suspend/resume patches; this patch should go
to Linus at the same time those do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as580) is perhaps the only result from the long discussion I
had with David about his changes to the root-hub suspend/resume code. It
renames the hub_suspend and hub_resume methods in struct usb_hcd to
bus_suspend and bus_resume. These are more descriptive names, since the
methods really do suspend or resume an entire USB bus, and less likely to
be confused with the hub_suspend and hub_resume routines in hub.c.
It also takes David's advice about removing the layer of bus glue, where
those methods are called. And it implements a related change that David
made to the other HCDs but forgot to put into dummy_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as574) updates the PCI BIOS usb-handoff code for UHCI
controllers, making it work like the reset routines in uhci-hcd. This
allows uhci-hcd to drop its own routines in favor of the new ones
(code-sharing).
Once the patch is merged we can turn the usb-handoff option on
permanently, as far as UHCI is concerned. OHCI and EHCI may still have
some issues.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as563) splits the physical and logical framelist arrays in
uhci-hcd into two separate pieces. This will allow slightly better memory
utilization, since each piece is no larger than a single page whereas
before the whole thing was a little bigger than two pages. It also allows
the logical array to be allocated in non-DMA-coherent memory.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as562) removes from the uhci-hcd driver a few unused fields
and some unnecessary tests against NULL and assignments to NULL. In fact
it wasn't until fairly recently that the tests became unnecessary.
Before last winter it was possible that the driver's stop() routine would
get called even if the start() routine returned an error, but now that
can't happen. Hence there's no longer any need to check for partial
initialization.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as558) removes from the UHCI driver a kernel timer used for
checking Full Speed Bandwidth Reclamation (FSBR). The checking can be
done during normal root-hub polling; it doesn't need a separate timer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the way uhci-hcd detects valid ports. The
specification doesn't mention any way to find out how many ports a
controller has, so the driver has to use some heuristics, reading the port
status and control register and deciding whether the value makes sense.
With this patch the driver will recognize a typical failure mode (all bits
set to one) for nonexistent ports and won't assume there are always at
least 2 ports -- such an assumption seems silly if the heuristics have
already shown that the ports don't exist.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the host controller drivers; they no longer need to
register their root hubs because usbcore will take care of it for them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch simplifies the uhci-hcd driver by removing the device pointer
currently stored in the QH and TD structures. Those pointers weren't
being used for anything other than to increment the device's reference
count, which is unnecessary since the device is used only when an URB
completes, and outstanding URBs take their own reference to the device.
As a useful side effect, this change means that uhci-hcd no longer needs
to have the root-hub device available in the start routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After all the discussion you might not be interested in this still, but
nevertheless here it is. This patch adds a shutdown method to the
uhci-hcd driver. Its prerequisite is the patch you wrote adding shutdown
support for PCI.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch improves the strategy uhci-hcd uses for performing controller
resets and checking whether they are needed.
The HCRESET command doesn't affect the Suspend, Resume,
or Reset bits in the port status & control registers, so
the driver must clear them by itself. This means the
code to figure out how many ports there are has to be moved
to an earlier spot in the driver.
The R/WC bits in the USBLEGSUP register can be set by the
hardware even in the absence of BIOS meddling with legacy
support features. Hence it's not a good idea to check them
while trying to determine whether the BIOS has altered the
controller's state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, which has as478b as a prerequisite, enables the uhci-hcd
driver to take advantage of root-hub IRQs rather than polling during the
time it is suspended. (Unfortunately the hardware doesn't support
port-change interrupts while the controller is running.) It also turns
off the driver's private timer while the controller is suspended, as it
isn't needed then. The combined elimination of polling interrupts and
timer interrupts ought to be enough to allow some systems to save a
noticeable amount of power while they are otherwise idle.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tidies up a few loose ends left by the preceding patches.
It indicates the controller supports remote wakeup whenever the PM
capability is present -- which shouldn't cause any harm if the
assumption turns out to be wrong. It refuses to suspend the
controller if the root hub is still active, and it refuses to resume
the root hub if the controller is suspended. It adds checks for a
dead controller in several spots, and it adds memory barriers as
needed to insure that I/O operations are completed before moving on.
Actually I'm not certain the last part is being done correctly. With
code like this:
outw(..., ...);
mb();
udelay(5);
do we know for certain that the outw() will complete _before_ the
delay begins? If not, how should this be written?
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements (finally!) separate suspend and resume routines
for the root hub and the controller in the UHCI driver. It also
changes the sequence used to reset the controller during initial
probing, so as to preserve the existing state during a Resume-From-Disk.
(This new sequence is what should be used in the PCI Quirks code for
early USB handoffs, incidentally.) Lastly it adds a notion of the
controller being "inaccessible" while in a PCI low-power state, when
normal I/O operations shouldn't be allowed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch starts making some serious changes to the UHCI driver.
There's a set of private states for the root hub, and the internal
routines for suspending and resuming work completely differently, with
transitions based on the new states. Now the driver distinguishes
between a privately auto-stopped state and a publicly suspended state,
and it will properly suspend controllers with broken resume-detect
interrupts instead of resetting them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes a few small improvements in the UHCI driver. Some
code is moved between different source files and a more useful pointer
is passed to a callback routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves a few subroutines around in the uhci-hcd source file.
Nothing else is changed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of a bunch of redundant NULL pointer checks in drivers/usb/*,
there's no need to check a pointer for NULL before calling kfree() on it.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/class/audio.c
===================================================================
This patch includes minor "sparse -Wbitwise" updates for the PCI based
HCDs. Almost all of them involve just changing the second parameter of the
suspend() method to a pm_message_t ... the others relate to how the EHCI
code walks in-memory data structures. (There's a minor bug fixed there too
... affecting the big-endian sysfs async schedule dump.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/hcd.h
===================================================================
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
