Since frames per second is a function of cristal frequency, and this is
device-specific, add a function that allows adjusting it, via
subdev->core->s_config callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is possible to adjust the fps rate by changing some register values.
This is function of the connected Xtal at the camera sensor, being a 27
MHz cristal needed, in order to support 640x480 at 30 fps.
For now, it will only calculate the values for fps. Later patches may
introduce V4L2 ioctls, to allow frequency rate adjustments.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While trying to fix an mt9v001 webcam, I noticed that HSCALE/VSCALE do
work with em28xx + webcam. The issue is that the scaling setup depends
on the number of visible rows/cols of the input image.
With mt9v011 (Silvercrest), the resolution is 640x480. So, the scaling
is different from a normal TV image (720x480 on NTSC). This were causing
a wrong scaling and a previous patch disabled scaling.
As each sensor have their different resolution setting, the xres/yres
should be adjusted accordingly with the input sensor.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the previous approach, autodetection were working only for the two
generic entries (em275x and em2820 unknown ones). So, if someone would
try to force probing an specific device, the code would not properly run
the autodetection code.
With the new approach, the sensor autodetection will be run not only for
the two generic entries, but also do webcam specific ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using em28xx board decoder field for storing sensor information,
let's use instead a separate field for it.
Also, as sensors are currently autodetected, there's no need of having
it at the boards description. So, move it to the main em28xx struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Webcams in general don't have eeprom. So, the sensor hint code should be
called to properly detect what sensor is inside.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By having the webcam devices marked as such, it will help the em28xx
driver to do the right thing on those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just renames the flag, to use a clearer name. Later patches will use
this flag to properly set some drivers behaviors for webcams.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A couple of erroneous register writes snuck in that made the image go haywire. Remove these.
Many thanks to Grégory Lardière for finding this out
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All hdcs registers use bit 0 as a read/write flag and needs to be shifted one bit to the left. This wasn't accounted for when doing a sequence of writes.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is one path with omitted unlock in si470x_fops_release. Fix that.
Cc: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is one omitted unlock in em28xx_usb_probe. Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Discovered the bug that were limiting the output format to just RGB565.
Now, it is possible to output image at Bayer format (the original one,
as generated by Silvercrest sensor, and two others), and also on YUY.
Adds Bayer formats also to the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Webcams have different constraints than other v4l devices. This patch
makes the format ioctls to behave better. It also fixes a bug at open()
handler, that were always reseting resolution to the maximum available
one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the code so that the zl10353 version of the Terratec Cinergy T XS USB
starts working again. This includes fixing what must have been a typo in the
GPIO definition for the digital side of the board, and setting of the
disable_i2c_gate_ctrl property for the zl10353 config, so that the i2c bus
doesn't get wedged the first time something tries to close the gate.
Also, add a printk() making clear that the mt352 version still isn't
supported. This issue is still being actively debugged, but in the meantime
at least the dmesg output will show a very clear error...
Thanks to Jelle de Jong for providing sample hardware to test with.
Thanks to Simon Kenyon for testing various patches and providing SSH access to
his environment so I could debug with access to a valid signal source.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Cc: Simon Kenyon <simon@koala.ie>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add suppport for the teste RGB565 format (16 bits/pixel).
Currently, webcam support works only at RGB565, at 640x480.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This webcam uses a em2710 chipset, that identifies itself as em2820,
plus a mt9v011 sensor, and a DY-301P lens.
It needs a few different initializations than a normal em28xx device.
Thanks to Hans de Goede <hdegoede@redhat.com> and Douglas Landgraf
<dougsland@redhat.com> for providing the acces for the webcam during
this weekend, I could make a patch for it while returning back from
FISL/Fudcom LATAM 2009.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original driver for Silvercrest cameras were using some values that
are different from what datasheet says. As result, it was taken very
less snapshots per second than expected.
A test with the datasheet values showed that they work fine and give a
better frame rate. So, let's stick with datasheet values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of working with a table of precalculated values, fill them with
the proper values. Also, adds format functions that allow changing the
resolution, by cropping the image to the center of the sensor.
While here, move the sensor version check to the probe routine, to
indicate to the caller if the sensor is not supported by this driver.
Also, fixes a stupid bug where we're using &buffer[] instead of
buffer[].
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds driver for mt9v011 based on its datasheet, available at:
http://download.micron.com/pdf/datasheets/imaging/MT9V011.pdf
The driver was tested with a webcam that will be added on a next patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
add FIXME comment to indicate that the set_frontend override is a
temporary hack. This will be done a better way in the next kernel.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use separate RF input spigots for Antennae and Cable.
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add DVB-T support for Yuan MPC-718 cards with an MT352 or ZL10353 demodulator.
There are apparently some units with a DiBcom demodulator which could be
supported by one of the dib7000 modules - but this is not implemented in the
cx18 driver (yet).
Due to lack of porgramming details for the MT352 and the mt352 module requiring
a "demod_init" function, a "firmware" must be obtained and loaded to get
DVB-T working for Yuan MPC-718 cards with an MT352.
Tested-by: Steve Firth <firth650@btinternet.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch should fix 7 MHz DVB-T with the XC3028 using the
DTV7 firmware from the xc3028-v27.fw firmware image.
Tested-by: Terry Wu <terrywu2009@gmail.com>
[mchehab@redhat.com: thanks to John Ferlito, we have a real test in Australia]
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If soc_camera_init_user_formats() fails in soc_camera_probe(), we have to call
client's .remove() method to unregister the video device.
Reported-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The supported formats count must be set to 0 after debug output
right before the second pass.
Signed-off-by: Stefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If I2C is not enabled, then we shouldn't build ttpci_eeprom.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
precalculate_bars() improved vivi performance. However, it assumed that
always before streaming, the driver would call VIDIOC_S_STD. This is not
an API requirement, and the testing apps don't do that.
Due to that, a regression were caused by the patch that added it.
This patch moves the precalculate_bars to the proper place of the code,
calling it at buffer_prepare() callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
loaded for a given chip version. This would cause the optimization in
tuning not to be applied and thus a failed expectation, in tuning speed
increment. The patch swaps the tables in use. It also fixes a possible
one in a million condition where state->dev_ver implies an older Cut
(Cut < 2.0, eventhough the driver doesn't attach to any Cut older than
2.0) or even negative (due to a bad I2C bus master driver) for the card
combination.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing
out the issue at large.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_optimize_carloop_short’:
drivers/media/dvb/frontends/stv090x.c:2677: warning: ‘short_crl’ may be used uninitialized in this function
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Fri, 12 Jun 2009, Randy Dunlap wrote:
> From: Randy Dunlap <randy.dunlap@oracle.com>
>
> Move v4l_bound_align_image() outside of an #ifdef CONFIG_I2C block
> so that it is always built. Fixes a build error:
clamp_align() should be moved as well, since it's only used by
v4l_bound_align_image(). I'm attaching an alternate version that fixes
this. Labeled the endif too.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the TRY_FMT handler the function get_scale() is called to find what the
scaler hardware will produce for a requested size.
The problem is that get_scale(struct cx231xx *dev, ..., unsigned int *vscale,
unsigned int *hscale) saves the calculated scale values into both the
pointer arguments and into dev's hscale and vscale fields. TRY_FMT shouldn't
actually change anything in the device state.
The code to in get_scale() that writes to dev->[hv]scale can just be
deleted. In all cases when dev's fields should be modified, get_scale()
was called with get_scale(dev, ..., &dev->hscale, &dev->vscale), so dev was
getting updated anyway.
This didn't actually cause a problem because nothing ever actually made use
of the hscale and vscale fields. I changed cx231xx_resolution_set() to use
those fields rather than re-calculate them with a call to get_scale().
Updating [hv]scale in cx231xx_resolution_set() isn't necessary because
every call of cx231xx_resolution_set() was already preceded by a call to
get_scale() or setting the [hv]scale fields, so they will be always be
up-to-date w.r.t. width and height.
Removing the call to get_scale() from cx231xx_resolution_set() allowed
making get_scale() a static function, which is a good thing for something
with such a short name. There is already another function with the same
name in the em28xx driver, but that one is static.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l function has a better algorithm for aligning image size.
It appears that the em2800 can only scale by 50% or 100%, i.e. the only
heights supported might be 240 and 480. In that case the old code would
set any height other than 240 to 480. Request 240 get 240, but request 239
and then you get 480. Change it to round to the nearest supported value.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l function has a better algorithm for aligning image size.
Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l function has a better algorithm for aligning image size.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l function has a better algorithm for aligning image size.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l function has a better algorithm for aligning image size.
The existing code was casting pointers to u32 and to unsigned int into
pointers to u16. This could mess up if someone passed in an image size
greater than 65,535 and on big-endian platforms it won't work at all.
The existing bounding code would shrink an image if it was too big, but
returned ERANGE if it was too small. The code will not shrink or expand as
necessary.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l function has a better algorithm for aligning image size.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l function has a better algorithm for aligning image size.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l function has a better algorithm for aligning image size.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>