The Ethernet Switch core mask was set to 0, causing the switch core to
be not reset on BCM6368 on boot. Provide the proper mask so the switch
core gets reset to a known good state.
Fixes: 799faa626c ("MIPS: BCM63XX: add core reset helper")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. In the case of
some code where it is modular, we can extend that to also include
files that are building basic support functionality but not related
to loading or registering the final module; such files also have
no need whatsoever for module.h
The advantage in removing such instances is that module.h itself
sources about 15 other headers; adding significantly to what we feed
cpp, and it can obscure what headers we are effectively using.
Since module.h might have been the implicit source for init.h
(for __init) and for export.h (for EXPORT_SYMBOL) we consider each
instance for the presence of either and replace/add as needed.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Build coverage of all the mips defconfigs revealed the module.h
header was masking a couple of implicit include instances, so
we add the appropriate headers there.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Steven J. Hill" <steven.hill@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15131/
[james.hogan@imgtec.com: Preserve sort order where it already exists]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
The Broadcom BCM3368 Cable Modem SoC is extremely similar to the
existing BCM63xx DSL SoCs, in particular BCM6358, therefore little effort
in the existing code base is required to get it supported. This patch adds
support for the following on-chip peripherals:
- two UARTS
- GPIO
- Ethernet
- SPI
- PCI
- NOR Flash
The most noticeable difference with 3368 is that it has its peripheral
register at 0xfff8_0000 we check that separately in ioremap.h. Since
3368 is identical to 6358 for its clock and reset bits, we use them
verbatim.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5499/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add basic support for detecting and booting the BCM6362.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5009/
Acked-by: John Crispin <blogic@openwrt.org>
Add a reset helper for resetting the different cores.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4455
Signed-off-by: John Crispin <blogic@openwrt.org>
