Adjust the equation for selector >= 15 for better readability.
The equation "1700000 + ((selector - 15) * 100000)" can be interpreted by:
Starting from selector 15: Steps of 100mV from 1700mV
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To apply delay time for voltage change,
replace s5m8767_set_voltage with s5m8767_set_voltage_sel.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Call wm8400_ldo_list_voltage() instead of open code to verify selected voltage
falls within specified range.
Use wm8400_ldo_list_voltage() here is less error prone.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As s5m8767a is revisioned, remove unnecessary buck 2,3,4 initialization routine.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
rdev->desc->uV_step * abs(new_selector - old_selector) returns uV.
The unit of ramp_delay is mV/us.
Current code multiples 1000 at wrong place.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
rdev->desc->uV_step * abs(new_selector - old_selector) returns uV.
The unit of ramp_rate is mV/us.
Thus 1000 should be multiplied.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds regulator_set_voltage_time_sel(), to move into core, the
commonly used code by drivers to provide the .set_voltage_time_sel callback.
It will also allow us to configure different ramp delay for different
regulators easily.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If this driver only works when pdata->num_regulators == MAX77686_REGULATORS,
let's check it earlier.
Also remove unused num_regulators from struct max77686_data.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
isl_fixed_ops does not implement set_voltage_sel callback, adding map_voltage
here is misleading.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also adds tps6586x_ldo0_voltages mapping table for LDO0, so we can remove the
hack in tps6586x_list_voltage() and convert it to regulator_list_voltage_table.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's a little bit hard to read that the "else" case means id == PALMAS_REG_SMPS10.
if (id != PALMAS_REG_SMPS10){
do something for the cases id != PALMAS_REG_SMPS10;
} else {
do something for the case id == PALMAS_REG_SMPS10;
}
This patch changes above syntax to switch statement.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code actually clears more bits than PALMAS_SMPS12_CTRL_MODE_ACTIVE_MASK bits.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For linear mappings, we can use below equation to get the voltage difference
between new_selector and old_selector:
abs(new_selector - old_selector) * rdev->desc->uV_step
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For fixed voltage, DA9030_LDO13 and DA9034_LDO5, the info->vol_reg is
DA9030_INVAL/DA9034_INVAL.
It does not make sense to read/write to DA9030_INVAL/DA9034_INVAL address.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixed voltage is a kind of linear mapping where n_voltages is 1.
This change allows [list|map]_voltage_linear to be used for fixed
voltage.
For fixed voltage, n_voltages is 1 and the only valid selector is 0.
Thus we actually don't care the uV_step setting.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Properly handle the case if the specified min_uV is less than the voltage given
by the lowest selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The voltage mapping table for LDO2 is exactly the same as VDCDCx.
Thus we can use one mapping table for both LDO2 and VDCDCx instead of
duplicating the mapping table.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The min_uV and max_uV are not used in this driver.
For table based voltage mappings, we can get min_uV and max_uV by
info->table[0] and info->table[table_len -1].
Thus remove min_uV and max_uV from struct tps_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In probe(), rdev->regmap must be assigned.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below checkpatch warnings:
$ scripts/checkpatch.pl -f drivers/regulator/max77686.c
ERROR: return is not a function, parentheses are not required
+ return (DIV_ROUND_UP(rdev->desc->uV_step
WARNING: line over 80 characters
+ .ops = &max77686_buck_dvs_ops, \
total: 1 errors, 1 warnings, 339 lines checked
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This was missing until now and the underlying
_regulator_do_set_voltage is using this value when calling list_voltage.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 4dbd8f63f0 (regulator: gpio-regulator: Set the smallest
voltage/current in the specified range) forgot to set the newly
introduced best_val.
Therefore it stayed always at INT_MAX thus breaking the setting
of the voltage.
Included is also an init value for target, as warnings about
a possibly uninitialised target started appearing with this fix.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit c172708d38 (regulator: core: Use a struct to pass in
regulator runtime configuration) added the drvdata pointer
only per reference to the new config array in the gpio-regulator.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
__devexit functions are discarded when CONFIG_HOTPLUG
is not set, so the symbol needs to be referenced carefully.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The devm_kzalloc function eliminates the need for manual resource releasing
and simplify error handling. Resources allocated by devm_* are freed
automatically on driver detach.
Thus adding kfree calls here will introduce double free bug.
The memory of desc array and the pointers to the rdev[] are allocated by
devm_kzalloc call for struct palmas_pmic.
struct palmas_pmic {
struct palmas *palmas;
struct device *dev;
struct regulator_desc desc[PALMAS_NUM_REGS];
struct regulator_dev *rdev[PALMAS_NUM_REGS];
struct mutex mutex;
int smps123;
int smps457;
int range[PALMAS_REG_SMPS10];
};
Which means we should not call kfree for pmic->rdev and pmic->desc.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since there are two linear ranges for the LDO voltages provide a voltage
mapping function and then use regulator_set_voltage_sel_regmap().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both max77686_ops and max77686_buck_dvs_ops use simple linear voltage maps.
Thus use regulator_map_voltage_linear is more efficient than using the defult
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm8350_dcdc_ops uses simple linear voltage maps.
Thus use regulator_map_voltage_linear is more efficient than using the default
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the db8500-prcum regulator driver so
this is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the ab8500 regulator driver so this
is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the new of_match_ptr() macro for the of_match_table
pointer entry to avoid having to #define match NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add driver for support max77686 regulator.
MAX77686 provides LDOs[1~26] and BUCKs[1~9]. It support to set or get the
volatege of regulator on max77686 chip with using regmap.
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm8400_dcdc_ops uses simple linear voltage maps.
Thus use regulator_map_voltage_linear is more efficient than using the default
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm831x_alive_ldo_ops uses simple linear voltage maps.
Thus use regulator_map_voltage_linear is more efficient than using the default
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8350 DCDCs have a simple linear mapping from selectors to voltages
so can be converted very simply to use the new infrastructure for a nice
reduction in code size.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If no regmap is explicitly specified then use dev_get_regmap() to obtain
one. The driver must explicitly enable any actual usage of the regmap
so there's no concern with unwanted usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
devres_release() will call the destructor for the resource as well as
freeing the devres data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If the regulator is not on, it won't take time setting new voltage.
So only call set_voltage_time_sel() to get the necessary delay when
the regulator is on.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some regulator hardware use table based mapping can set volt_table in
regulator_desc and use regulator_list_voltage_table() for their list_voltage
callback.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rh0r
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
The major thing here is the addition of some helpers to factor code out
of drivers, making a fair proportion of regulators much more just data
rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI TPS65913,
TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring caused
so many conflicts that eventually topic branches were abandoned for this
release.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPuhn4AAoJEBus8iNuMP3d6m4P/0gNiGbTwDlOgU/mPDyW2jJc
xqvABzlOIQbI28/dgFYO/nA9YWW7VxpEaAPlkg4auk4wQ9tEyEjEqlOCfzymMetY
0k6L4n8LqFsbMAeNQbFPbW7PpWp59oI97J9afJI4kEJmHmOlmlL9U82/TzUFfGrA
yiPlzue+DotKB7FjsymLMbLyeFoiMSOIjVDk8OTs0u1EqeOo4nJG2ODLa+yGo+QW
0yqQExEdIp28WXbkZQtmsOmj2V/uhkKAv2i2PDT2TmlduhNdCGxJsgZIiZCl1R4c
vwirbfb+v93HAxvADdgj8eVdLJXQ0oItxr2ohKt8AgXIBrUJBsMkCQGvulZjRb+a
/A/7Ea3o7HI+PQx4aIP0yGA/eBwbzo/cmBxU+KGzTA9Mov0fnK1kkUs6gfrYBdli
U/TcMizDa1539BrKBIF2gmlRCKx8YD9ic27Zl1x4i5cgAP1gdYgdBYBybKHMpo2+
9Xp1R9C8FvvgytIqJ3QQ34tRomZyQ5iUaIuIuAosoQ6iuF33EQ6I0FvHcIe74iOi
zcu62ZPiuSwg1di9PrTERLcbrS81lvXpOWt5+EorzqoGXWzVIGoTh1F2kWEEMhaD
Q6V5iE03VC0k3tj/MmtTiVkyhNkRElQDtekE9sfm15pdVnpu/+b+iicWJa7QFbZQ
MybS0BBFQKhJXUDttKtS
=UR7s
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The major thing here is the addition of some helpers to factor code
out of drivers, making a fair proportion of regulators much more just
data rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI
TPS65913, TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring
caused so many conflicts that eventually topic branches were abandoned
for this release."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (227 commits)
regulator: tps65910: use of_node of matched regulator being register
regulator: tps65910: dt: support when "regulators" node found
regulator: tps65910: add error message in case of failure
regulator: tps62360: dt: initialize of_node param for regulator register.
regulator: tps65910: use devm_* for memory allocation
regulator: tps65910: use small letter for regulator names
mfd: tpx6586x: Depend on regulator
regulator: regulator for Palmas Kconfig
regulator: regulator driver for Palmas series chips
regulator: Enable Device Tree for the db8500-prcmu regulator driver
regulator: db8500-prcmu: Separate regulator registration from probe
regulator: ab3100: Use regulator_map_voltage_iterate()
regulator: tps65217: Convert to set_voltage_sel and map_voltage
regulator: Enable the ab8500 for Device Tree
regulator: ab8500: Split up probe() into manageable pieces
regulator: max8925: Remove check_range function and max_uV from struct rc5t583_regulator_info
regulator: max8649: Remove unused check_range() function
regulator: rc5t583: Remove max_uV from struct rc5t583_regulator_info
regulator: da9052: Convert to set_voltage_sel and map_voltage
regulator: max8952: Use devm_kzalloc
...
After getting matched regulators by using of_regulator_match(),
initialize the config.of_node of regulator being register with
of_regulator_match.of_node of that regulator.
This is require for supporting regulator consumers in dt.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The device tree binding for the tps65910 is described as:
tps65911 {
reg = <0x2d>
:::::::::
regulators {
compatible = "ti,tps65911";
ldo1_reg: ldo1 {
/** regulator entry */
};
ldo2_reg: ldo2 {
/** regulator entry */
};
::::::::::
};
};
Support the regulators functionality only when there is "regulators"
child node available for tps65910.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prints error message whenever there is failure on resource
allocation.
Also used dev_* to print messages instead of pr_*
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize config.of_node for regulator before registering.
This is needed for DT based regulator support.
Regulator stores this of_node value in rdev->dev.of_node
and used for lookup when client ask for regulator_get().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- rename to anatop_read_reg and anatop_write_reg
- anatop_read_reg directly return reg value
- anatop_write_reg write reg with mask
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The modern idiom is to use irq_domain to allocate interrupts. This is
useful partly to allow further infrastructure to be based on the domains
and partly because it makes it much easier to allocate virtual interrupts
to devices as we don't need to allocate a contiguous range of interrupt
numbers.
Convert the wm831x driver over to this infrastructure, using a legacy
IRQ mapping if an irq_base is specified in platform data and otherwise
using a linear mapping, always registering the interrupts even if they
won't ever be used. Only boards which need to use the GPIOs as
interrupts should need to use an irq_base.
This means that we can't use the MFD irq_base management since the
unless we're using an explicit irq_base from platform data we can't rely
on a linear mapping of interrupts. Instead we need to map things via
the irq_domain - provide a conveniencem function wm831x_irq() to save a
small amount of typing when doing so. Looking at this I couldn't clearly
see anything the MFD core could do to make this nicer.
Since we're not supporting device tree yet there's no meaningful
advantage if we don't do this conversion in one, the fact that the
interrupt resources are used for repeated IP blocks makes accessor
functions for the irq_domain more trouble to do than they're worth.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This change removes the read/write callback functions in favor of common
regmap accessors inside the header file. This change also makes use of
regmap_read/write for single register access which maps better onto what this
driver actually needs.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
use the devm_* apis for memory allocation.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the small-letter for names of different regulator to
match the names with dt binding documents.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the Kconfig/Makefile stuff for the palmas regulator driver
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Palmas has both Switched Mode (SMPS) and Linear (LDO) regulators in it.
This regulator driver allows software control of these regulators.
The regulators available on Palmas series chips vary depending on the muxing.
This is handled automatically in the driver by reading the mux info from OTP.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here we use the previous regulator register code separated from probe to
register each of the regulators mentioned in Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will provide us with a convenient way to register regulators when
booting with Device Tree both enabled & disabled and will save us a
great deal of code duplication in time.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_map_voltage_iterate() is for drivers implementing set_voltage_sel()
and list_voltage() to use it as their map_voltage() operation.
In this case, regulator_map_voltage_iterate() happen to be doing the same thing
as ab3100_get_best_voltage_index() function. So we can use it to replace
ab3100_get_best_voltage_index() function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert tps65217_pmic_ops to use set_voltage_sel and map_voltage.
After this convertion, we can also use tps65217_pmic_set_voltage_sel()
for set_voltage_sel callback of tps65217_pmic_ldo1_ops.
Thus this patch also removes tps65217_pmic_ldo1_set_voltage_sel() function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here we setup the ab8500 regulator driver for DT. We first do
this in the normal way, by providing a match structure during
initialisation, but then we provide information so that
whilst probing we can use existing data structures to do DT
look-ups.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ab8500's probe() function is becoming quite large, so in the lead
up to Device Tree enablement which will fork the thread of execution
this patch splits it into 3 main areas; basic error checking will
remain in probe(), but regulator register initialisation and regulator
registration have been moved to their own functions which will
be called in sequence by probe() and the DT equivalent.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver has been converted to use regulator_map_voltage_linear and
set_voltage_sel now. regulator_map_voltage_linear will check the the voltage
falls within specified range. The check_range() function and max_uV field are
not used now, remove them.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver has been converted to use regulator_map_voltage_linear and
set_voltage_sel now. regulator_map_voltage_linear will check the the voltage
falls within specified range. The check_range() function is not used, remove it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver has been converted to set_voltage_sel and regulator_map_voltage_linear.
regulator_map_voltage_linear will check the voltage falls within specified range.
The max_uV field is not used now, remove it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now the implementation of da903x_set_voltage_sel, da9030_set_ldo14_voltage_sel,
and da9034_set_ldo12_voltage_sel are exactly the same.
da903x_get_voltage_sel, da9030_get_ldo14_voltage_sel and
da9034_get_ldo12_voltage_sel are exactly the same.
So we can use da903x_[get|set]_voltage_sel and kill other functions.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use regulator_list_voltage_linear() to replace da903x_list_voltage().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the mechanism of enabling the force PWM mode through
regulator set mode. This can be dynamically configured now.
In the REGULATOR_MODE_FAST the force PWM is enabled and in
REGULATOR_MODE_NORMAL the force PWM is disabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we fail while registering a regulator make sure we release the supply
for the regulator if there is one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Integer division may truncate the result.
Use DIV_ROUND_UP to ensure simple linear voltage mappings falls within the
specified range.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add dt support for the pmu device tps62360 and
Add binding documentation with example.
With this patch driver will support both device-tree and
non-device tree registration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert platform data member regulator_init_data to pointer type.
This will avoid the copy of entire regualator init data into
platform data member when adding dt support and it can be achieve
by simple assignment:
pdata->init_data = of_get_regulator_init_data(dev, dev->of_node);
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add devicetree based initialization support for TI tps65910 regulators.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
da903x_list_voltage does not return correct voltage for da9030 ldo14.
Implement da9030_list_ldo14_voltage to return correct voltage for da9030 ldo14.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the driver to use all the regmap based helpers, saving a nice chunk
of code (especially for the DCDCs).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only the alive LDOs can actually use this as all the other regulators have
two linear ranges.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A lot of regulator hardware maps selectors on to voltages with a simple
linear mapping function
selector = base + (selector * step size)
Provide off the shelf list_voltage() and map_voltage() operations which
use new min_uV and uV_step members in the regulator_desc to implement
this function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow more drivers to factor things out into data allow
drivers to provide a mapping function to convert voltages into selectors.
This allows any driver to use set_voltage_sel(). The existing mapping
based on iterating over list_voltage() is provided as an operation which
can be assigned to the new map_voltage() function though for ease of
transition it is treated as the default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The core really wants a struct device to be supplied for regulators and
there's no reason this should be impossible so provide one so complain
if we didn't get one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Register all normal regulators rather than skipping unconfigured ones now
that the core can handle regulators without init data. Skip the boost and
isink regulators since they are normally controlled by other drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulators in the twl4030 can provide some voltage settings
that are not offically supported.
These settings are disabled by default, but can be enabled with
CONFIG_TWL4030_ALLOW_UNSUPPORTED=y
However
- that config variable is not mentioned in any Kconfig so cannot
be used, and
- a global setting is clumsy - a per regulator setting would be
better.
So define a new 'feature' flag that a board file can set to enable
these unsupported volatages for boards which need them.
This flag cannot (yet) be set using device-tree.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This makes logging a bit clearer as it gives the actual bus location and
makes things like board hookup a bit smoother.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix multiple stylistic issue like:
- The print message should be not break into multiple line.
- line gap after variable declaration and statement.
- checkpatch error.
- some typo.
Some enhancement on error message printing to print error value
also along with proper text.
Avoid voltage_base conversion to microvolts every time.
Put init functions in init section.
Using efficient function inplace of calling multiple function
to reduce the code size.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Settling time is require when there is voltage output change.
Implement set_voltage_time_sel() callback which returns delay time
for voltage change to settle down to new value.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable cache of device register using regmap cache RBTREE.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It turns out that (quite surprisingly) devres_destroy() only undoes the
devres mapping, it doesn't destroy the underlying resource, meaning that
anything using devm_regulator_put() would leak. While we wait for the new
devres_release() which does what we want to get merged open code it in
devm_regulator_put().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The driver of da9052 is buggy due to the iteration loop of device tree.
This patch fix the loop condition to make the driver work with device tree.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add property for the gpio flag open drain when registering
fixed regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit adds device tree support for the TPS6586x regulator.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Looking up init data for regulators found on chips is a common operation
that can be handled in a generic way. The new helper function introduced
by this patch looks up the children of a given node by names specified
in a match table and fills that match table with information parsed from
the DT.
This is based on work by Rhyland Klein <rklein@nvidia.com>.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also simplify the error handling to start unwind from the place
regulator_register fails.
No need to check rdev[i] is NULL or not before calling regulator_unregister.
regulator_unregister is safe if rdev is NULL,
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also simplify the error handling to start unwind from the place
regulator_register fails.
No need to check rdev[i] is NULL or not before calling regulator_unregister.
regulator_unregister is safe if rdev is NULL,
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All the drivers that need delay for the regulator voltage output voltage to
stabilize after being enabled or after being set to a new value has been
converted to implement enable_time and set_voltage_time_sel callbacks.
Then regulator core will take care of the necessary delay.
For the drivers that don't need the delay, don't need to include linux/delay.h.
This patch removes the unneeded include of linux/delay.h in regulator drivers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 8ac0e95 "regulator: core: Support setting suspend_[mode|voltage]
if set_suspend_[en|dis]able is NULL", now the regulator core can properly
handle the case set_suspend_enable callback is NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If is_enabled callback is not implemented, the core assumes that the regulator
is on.
This is simpler than having a hack to retrun 1 in max8997_reg_is_enabled() if
max8997_get_enable_register() returns -EINVAL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Integer division may truncate the result.
Use DIV_ROUND_UP to ensure new voltage setting falls within specified range.
Also properly handle the case min_vol < desc->min to ensure we don't return
negative value for selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regulator is always on for any reason then cache that when the
consumer is created and use it to optimise away the need to take locks
or recurse up the supply tree when consumers do enable or disable calls.
The scheduling of asynchronous work for bulk enables is also skipped.
We don't actually check if the device physically supports control on the
basis that constraints allowing status changes on physically always on
regulators are nonsensical anyway.
This is a very common pattern in hardware - it's normal to have some
power supplies that have either no software control or are critical to
system function - so many systems should be able to benefit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
strict_strtol is deprecated and results in a checkpatch warning.
Replace it with kstrtol.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit 4ca1e1d "regulator: Convert 88pm8607 to set_voltage_sel" accidentally
changed the value writing to vol_reg.
What we want is to write val instead of selector to vol_reg.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch converts tps65090 regulator driver to use generic regmap
enable/disable operations.
Also move struct tps65090 to include/linux/mfd/tps65090.h because
the regulator driver needs to access the rmap field of struct tps65090.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also rename get_current_limit and set_current_limit callbacks
to max8997_get_current_limit and max8997_set_current_limit for
better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I think this is a typo.
To ensure new voltage setting won't greater than desc->max,
the equation should be desc->min + desc->step * new_val <= desc->max.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
commit 4d26f7 "regulator: max8660: Use devm_kzalloc()" missed to
replace kzalloc by devm_kzalloc. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_set_optimum_mode needs set_mode to properly work.
Add checking for set_mode callback in case it may be not implemented.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the enable(), disable() and is_enabled() operations for most regmap
based regulators come down to reading and updating a single register bit
we can factor out the code and allow these drivers to just define which
bit to update using the enable_reg and enable_mask fields in their desc
and then use operations provided by the core.
As well as the code saving this opens the door to future optimisation of
the bulk operations - if the core can realise that we are updating a
single register for multiple regulators then it should be able to combine
these updates into a single physical operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since the voltage selector operations are intended to directly map a
bitfield in the device register map into regulator API operations the
code for implementing them is usually very standard we can save some
code by providing standard implementations for devices using the regmap
API.
Drivers using regmap can pass their regmap in in the regmap_config
struct, set vsel_reg and vsel_mask in their regulator_desc and then
use regulator_{get,set}_voltage_sel_regmap in their ops. This saves
a small amount of code from each driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since many regulators use regmap for register I/O and since there's quite
a few very common patterns in the code allow drivers to pass in a regmap
to the core for use in generic code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In current implementation, to support set_suspend_voltage and set_suspend_mode
the regulator code needs the regulator driver to implement both
set_suspend_enable and set_suspend_disable callbacks.
This patch removes this limitation. In the case set_suspend_enable and/or
set_suspend_disable are NULL, the regulator code assumes we don't need to
do any thing to enable/disable regulator when system is suspended and
then will continue to handle set_suspend_mode and set_suspend_voltage.
Currently the regulator core creates suspend state related sysfs entries only
if both set_suspend_enable and set_suspend_disable callbacks are not NULL.
A side-effect of this change is that the regulator core will create suspend
state related sysfs entries unconditionally now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When supplied by another regulator, returns the supply regulator's output
voltage for inpu_uV.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's no need to implement set_voltage() as there is only a very small
range of selectors for the regulators in the WM8994 and the voltages are
not expected to vary frequently at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds device tree support for dialog regulators
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the twlreg_grp helper function is there, use it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Let regulator core do the necessary delay for us.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't support missing configs at all so segfaulting isn't that bad
but since we've got checks in the code move the dereference after them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a trivial rename to stop the build system complaining that we're
referencing things we shouldn't be.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=45TQ
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull a regulator build fix from Mark Brown:
"Fix a build warning in the anatop driver for 3.4
This is a trivial rename to stop the build system complaining that
we're referencing things we shouldn't be."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: anatop: fix 'anatop_regulator' name collision
commit 268a1 "regulator: twl-regulator: Use DIV_ROUND_UP at appropriate places"
introduced an off-by-one bug for setting vsel.
The linear calculation code in twl6030smps_list_voltage() does subtract index
by 1 so we need the vsel++ after DIV_ROUND_UP.
The original code use this trick to differentiate if we are going to set the
voltage to 0 or the voltage falls within the linear calculation range.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
