If the user moves directly from one button to another then we won't get a
no buttons pressed event and will therefore end up reporting that two
buttons are simultaneously pressed which isn't supported by the hardware.
Make sure we clear any existing button reports before reporting any new
ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In pathological cases the microphone detection may fail to report, for
example due to a failure to get a stable measurement. Provide a timeout
to cover such cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than measuring both HP channels we can simply directly measure the
microphone impedance and then rely on MICDET for final confirmation of the
presence of a suitable microphone. This improves the overall performance
of the identification process.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This extra check makes the procedure take longer and is of marginal use
in identification so do not execute it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes we can trigger measurements early if contacts are shorted during
a slow insertion. As well as debouncing add further robustness by retrying
if we get a high impedance measurement for headphones as this can indicate
that the headphones were not yet connected.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Occasionally we can trigger an interrupt before we have completed
impedance measurement, although the valid bit will still be set. This
patch spins reading the impedance value until a valid value is seen.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In cases where we see a brief (dis)connection of the jack detection signals
we may see a noop jack insertion or removal where the jack has returned to
the original state by the time the interrupt is serviced. Suppress these
events in order to save work and avoid confusing the rest of the code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure greater reliability by increasing the minimum threashold for
identifying a microphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to do this as HPDET identification will cause MICBIAS to
be powered down again.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Arizona button detection circuit is configurable, allowing the system
integrator to program a range of thresholds for the buttons supported on
the accessory but currently the driver uses the default button ranges and
does not provide any flexibility in how this is exposed to the application
layer.
Provide platform data allowing the user to control this and to map
the buttons to keys in the input subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some pathological use cases users may insert an accessory very slowly
causing multiple indeterminate measurements. Handle this by retrying many
measurements before we give up and declare a headphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.
For extcon instead of checking if the headphone output is enabled when
doing magic application unconditionally disable the output and restore
the state which ASoC wants set when undoing the magic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have a very similar sequence doing magic writes in several places
(one of which missed an update to interlock with the CODEC driver) so
factor it out into a function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
This patch use delayed workqueue to check cable state after a certain
time. If extcon-max8997 driver check cable state during booting of
platform, this couldn't send the correct notification of cable state
to extcon consumer. Alwasys, this driver should check cable state
after the completion of platform initialization
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch set default H/W line path according to platfomr data.
The MAX8997 MUIC device can possibly set UART/USB or UART_AUX
/USB_AUX to internal H/W line path of MUIC device. Namely, only
one H/W line is used for two operation.
For example,
if H/W line path of MAX8997 device set UART/USB, micro usb cable
is connected to AP(Application Processor) and if H/W line path
set UART_AUX/USB_AUX, micro usb cable is connected to CP(Coprocessor).
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch make max8997_muic_get_cable_type() function to remove
duplicate code for checking ADC/Charger cable type because almost
internal function need to read adc/chg_type value of MUIC register.
Also, remove *_detach() function, extcon-max8997 driver treat
attach/detach operation of cable in max8997_*_handler() function.
Lastly, this patch move defined constant in header file(include/
linux/mfd/max8997.h, max8997-private.h) because defined constant
is only used in the 'extcon-max8997.c'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch set default of ADC Debounce Time(25ms) during probe step.
Also, can possible change ADC Debounce Time according to H/W situation
by using max8997_set_adc_debounce_time()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch move defined constants to header file(max77693-private.h)
because of mask/unmask selectively interrupt of MUIC device according
to attribute of H/W board.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
'max77693_extcon_cable' is used only in this file. Hence
make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
'break' after 'return' is never executed and hence can be deleted.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
'max8997_extcon_cable' is used only in this file. Hence make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
More updates for v3.9, a mix of fixes for the code that's already there
and a few new features.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7J4T
-----END PGP SIGNATURE-----
Merge tag 'extcon-arizona-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
extcon: arizona: Updates for v3.9
More updates for v3.9, a mix of fixes for the code that's already there
and a few new features.
When using HPDET to identify the accessory still run MICDET before we
report a microphone in order to ensure that the accessory identified is
compatible with the MICDET detection ranges after having confirmed that
the device is not using a headphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This should always be the most accurate reading for supported accessory
configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is important to clear the wake trigger status bits otherwise DCVDD
will be held high independent of the state of the LDOENA line.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The magic is already done as part of enabling the headphone output so
does not need to be done when the headphone outputs are enabled. We hold
the DAPM lock so the headphone status can't be changed underneath us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The HPDET identification method does not have the same natural debounce
built into it that the standard MICDET method does so add some extra on
top of what the jack detection does in hardware to make sure we get a
robust result.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When starting microphone detection some headsets should be exposed to
the fully regulated microphone bias in order to ensure that they behave
in an optimal fashion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to tune detection rate and debounce suitably for their
mechanical parameters.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For iio_channel_get to work with OF based configurations, it needs the
consumer device pointer instead of the consumer device name as argument.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fix build error of following log:
drivers/built-in.o: In function `max77693_muic_remove':
extcon-max77693.c:(.text+0x664853): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `max77693_muic_probe':
extcon-max77693.c:(.text+0x664971): undefined reference to `input_allocate_device'
extcon-max77693.c:(.text+0x6649c1): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x6649d6): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x6649eb): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x664a00): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x664a15): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x664a20): undefined reference to `input_register_device'
drivers/built-in.o: In function `max77693_muic_adc_handler':
extcon-max77693.c:(.text+0x665318): undefined reference to `input_event'
extcon-max77693.c:(.text+0x66532a): undefined reference to `input_event'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now have mechanisms in place to allow retries so let's use them rather
than guessing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we clamp as quickly as possible after removal by disabling the
debounce while there is an accessory present.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With some GPIO control it is possible to detect microphones in a wider
range of configurations by directly measuring the microphone impedance
when the HPDET method cannot distinguish between the behaviour of the
two grounds. Allow a GPIO to be provided in platform data and use it to
implement this behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The accessory detection functionality in Arizona devices is flexible and
supports several system designs in addition to the default one implemented
by the existing driver. One such design uses the HPDET feature to determine
what kind of accessory is present by comparing measurements taken with the
two headphone grounds available on the device, implement that if selected
by platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Use the headphone detection to identify if the accessory is a headphone or
line load. There are two different revisions of the IP with different
register layouts, support both.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Some system designs provide an input on GPIO5 which in conjunction with
the jack detection feature indicates the presence of an accessory.
Support such systems, using the microphone clamp feature to minimise
wakeups of the processor.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Newer Arizona devices include a microphone clamp function which is tied to
jack detect. Activate this feature when present in order to ensure best
performance of the subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Allow configuration of the rise time for MICBIAS via platform data, the
delay required depends on things like the external component selection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The micd_pol GPIO is only requested if we've specified one greater than 0
so apply the same test before we set it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
