* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
ocores_i2c_of_probe needs to use a const __be32 type for handing
device tree property values. This patch fixed the following build
warning:
CC drivers/i2c/busses/i2c-ocores.o
drivers/i2c/busses/i2c-ocores.c: In function 'ocores_i2c_of_probe':
drivers/i2c/busses/i2c-ocores.c:254: warning: assignment discards qualifiers from pointer target type
drivers/i2c/busses/i2c-ocores.c:261: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For the I2C module to be wakeup capable, programming I2C_WE register (which
was skipped for OMAP4430) is needed even on OMAP4.
This fixes i2c controller timeouts which were seen recently with the static
dependency being cleared between MPU and L4PER clockdomains.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[ben-linux@fluff.org: re-flowed description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This errata occurs when the ARDY interrupt generation is enabled.
At the begining of every new transaction the ARDY interrupt is cleared.
On continuous i2c transactions where after clearing the ARDY bit from
I2C_STAT register (clearing the interrupt), the IRQ line is reasserted and the
I2C_STAT[ARDY] bit set again on 1. In fact, the ARDY status bit is not cleared
at the write access to I2C_STAT[ARDY] and only the IRQ line is deasserted and
then reasserted. This is not captured in the usual errata documents.
The workaround is to have a double clear of ARDY status in irq handler.
Signed-off-by: Richard woodruff <r-woodruff2@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When runtime PM is enabled, each OMAP i2c device is suspended after
each i2c xfer. However, there are two cases when the static suspend
methods must be used to ensure the devices are suspended:
1) runtime PM is disabled, either at compile time or dynamically
via /sys/devices/.../power/control.
2) an i2c client driver uses i2c during it's suspend callback, thus
leaving the i2c driver active (NOTE: runtime suspend transitions are
disabled during system suspend, so i2c activity during system
suspend will runtime resume the device, but not runtime (re)suspend it.)
Since the actual work to suspend the device is handled by the
subsytem, call the bus methods to take care of it.
NOTE: This takes care of a known suspend problem on OMAP3 where the
TWL RTC driver does i2c xfers during its suspend path leaving the i2c
driver in an active state (since runtime suspend transistions are
disabled.)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use strlcpy instead of strncpy.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks. Drop the
conditionals and remove the #ifdef blocks from the affected drivers.
Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the PM core wishes to transition away from the legacy suspend
and resume methods and since removing them makes using PM core features
like runtime PM much easier start warning when a driver is registered
using the legacy methods.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When devices use dev_pm_ops the I2C API is implementing standard functionality
for integration with runtime PM and for checking for the presence of a per
device op. The PM core provides pm_generic_ functions implementing this
behaviour - use them to reduce coupling with future PM updates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove real devices first and dummy devices last. This gives device
driver which instantiated dummy devices themselves a chance to clean
them up before we do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: stable@kernel.org
The SCx200 ACB driver supports ISA hardware as well as PCI. The PCI
hardware is CS5535/CS5536 based, and the device that it grabs is handled by
the cs5535-mfd driver. This converts the SCx200 driver to use a
platform_driver rather than the previous PCI hackery.
The driver used to manually track the iface list (via linked list); now it
only does this for ISA devices. PCI ifaces are handled through standard
driver model lists.
It's unclear what happens in case of errors in the old ISA code; rather than
pretending the code actually cares, I've dropped the (implicit) ignorance
of return values and marked it with a comment.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus/i2c-2638' of git://git.fluff.org/bjdooks/linux:
i2c-bfin-twi: move setup to the earlier subsys initcall
i2c-bfin-twi: handle faulty slave devices better
i2c-mv64xxx: send repeated START between messages in xfer
i2c-nomadik: fix regression on adapter name
i2c-omap: Set latency requirements only once for several messages
i2c-eg20t: add driver for Intel EG20T
i2c-ocores: add some device tree documentation
i2c-ocores: Use devres for resource allocation
i2c-ocores: Adapt for device tree
i2c-iop3xx: add iomem annotation
Some systems using this bus sometimes have very basic devices such as
regulators on the bus, so the I2C bus master needs to be loaded early.
This also matches the behavior of many other I2C bus master drivers.
Therefore initialize via subsys_initcall().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Faulty slave devices might drive SDA low after a transfer finishes. So,
when this scenario is detected, have the master generate up to 9 extra
clocks until the SDA is properly released.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The I2C specification explicitly describes both SDA and SCL as
bidirectional lines. An I2C master with a read-only SCL is thus not
compliant. If a slow slave stretches the clock, errors will happen,
so the bus can't be considered as reliable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a function pointer to decide whether to call i2c_add_adapter or
i2c_add_numbered_adapter. This makes the code more compact than the
current strategy of having the common code in a separate function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.
E.G. something like:
---------- ---------- Bus segment 1 - - - - -
| | SCL/SDA | |-------------- | |
| |------------| |
| | | | Bus segment 2 | |
| Linux | GPIO 1..N | MUX |--------------- Devices
| |------------| | | |
| | | | Bus segment M
| | | |---------------| |
---------- ---------- - - - - -
SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 5a0e3ad6af added direct inclusion
of <linux/slab.h> to those source files that appeared to need it, but
somehow missed this. On most architectures <linux/slab.h> is still
indirectly included, but there are exceptions such as alpha.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As stated into file include/linux/i2c.h we must send a repeated START
between messages in the same xfer groupset:
* Except when I2C "protocol mangling" is used, all I2C adapters implement
* the standard rules for I2C transactions. Each transaction begins with a
* START. That is followed by the slave address, and a bit encoding read
* versus write. Then follow all the data bytes, possibly including a byte
* with SMBus PEC. The transfer terminates with a NAK, or when all those
* bytes have been transferred and ACKed. If this is the last message in a
* group, it is followed by a STOP. Otherwise it is followed by the next
* @i2c_msg transaction segment, beginning with a (repeated) START.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Mauro Barella <mbarella@vds-it.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The Nomadik I2C adapter does not provide a name for the struct
passed into i2c_add_numbered_adapter() causing a regression on
2.6.37-rc3 due to commit 2236baa75f
adding sanity checks for adapters. Fix this by providing a name
proper.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ordinary I2C read consist of two messages. First a write operation
to tell register address and then read operation to get data.
CPU wake up latency is set and removed twice in read case.
Set latency requirement before the message processing loop
and remove the requirement after the loop to remove latency
adjustment operations between the messages.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This puts some documentation for the device tree configuration at the head
of the driver file. Hopefully this can get moved to a common area for this
type of documentation at a later date; unfortunately, there isn't really
such a place in the kernel tree at this time.
Furthermore, the regstep and clock-frequency parameters are really bus
parameters and should probably be passed to the driver in a better way.
Consider that a TODO.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch converts the i2c-cores driver to use devres routines for
resource allocation.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adapts the i2c-ocores driver for being defined and configured via
a device tree description.
The device tree bits need to be protected by CONFIG_OF guards as this is
still an optional feature.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Eliminate unnecessary casts and the following sparse warnings:
drivers/i2c/busses/i2c-iop3xx.c:65:9: warning: incorrect type in argument 1 (different base types)
drivers/i2c/busses/i2c-iop3xx.c:65:9: expected void const volatile [noderef] <asn:2>*<noident>
drivers/i2c/busses/i2c-iop3xx.c:65:9: got unsigned int
[ the previous warning is repeated 18 times ]
drivers/i2c/busses/i2c-iop3xx.c:456:33: warning: cast removes address space of expression
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This gets caught by the new sanity check code. Instead of the slash use a
different symbol. This was originally found by Major Lee who proposed a
rather more complex patch which changed the name according to the chip
type.
On the basis that we are in a late -rc and making Linus grumpy isn't always
a good idea (however fun) this is a simple alternative.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure I2C adapters being registered have the required struct
fields set. If they don't, problems will happen later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>