In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.
Fixes: 450b05c15f ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: broadcom: Wirespeed/downshift support
This patch series adds support for the Broadcom Wirespeed, aka
downsfhit feature utilizing the recently added ethtool PHY tunables.
Tested with two Gigabit link partners with a 4-wire cable having only
2 pairs connected.
Last patch in the series is a fix that was required for testing, which
should make it to -stable, which I can submit separate against net if
you prefer David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.
Fixes: 450b05c15f ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the downshift/Wirespeed enable/disable
toggles and specify a link retry value ranging from 1 to 9. Since the
integrated BCM7xxx have issues when wirespeed is enabled and EEE is also
enabled, we do disable EEE if wirespeed is enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to need these functions to implement support for Broadcom
Wirespeed, aka downshift.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When busy polling while a link is down (during a link-flap test), TX
timeouts were observed as well as the following messages in the ring
buffer:
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free tx failed. rc:-1
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free rx failed. rc:-1
These were resolved by checking for link status and returning if link
was not up.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Rob Miller <rob.miller@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commits 93821778de ("udp: Fix rcv socket locking") and
f7ad74fef3 ("net/ipv6/udp: UDP encapsulation: break backlog_rcv into
__udpv6_queue_rcv_skb") UDP backlog handlers were renamed, but UDPlite
was forgotten.
This leads to crashes if UDPlite header is pulled twice, which happens
starting from commit e6afc8ace6 ("udp: remove headers from UDP packets
before queueing")
Bug found by syzkaller team, thanks a lot guys !
Note that backlog use in UDP/UDPlite is scheduled to be removed starting
from linux-4.10, so this patch is only needed up to linux-4.9
Fixes: 93821778de ("udp: Fix rcv socket locking")
Fixes: f7ad74fef3 ("net/ipv6/udp: UDP encapsulation: break backlog_rcv into __udpv6_queue_rcv_skb")
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are a few small USB fixes and new device ids for 4.9-rc7.
The majority of these fixes are in the musb driver, fixing a number of
regressions that have been reported but took a while to resolve. The
other fixes are all small ones, to resolve other reported minor issues.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlg3ANIPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspE9wAmwaC
5MUY7ZvafHycRWZWr7GzMCsJAKC0HljXocIpk0hJxYLwAhcE+D+QCQ==
=dbqZ
-----END PGP SIGNATURE-----
Merge tag 'usb-4.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a few small USB fixes and new device ids for 4.9-rc7.
The majority of these fixes are in the musb driver, fixing a number of
regressions that have been reported but took a while to resolve. The
other fixes are all small ones, to resolve other reported minor
issues.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: f_fs: fix wrong parenthesis in ffs_func_req_match()
phy: twl4030-usb: Fix for musb session bit based PM
usb: musb: Drop pointless PM runtime code for dsps glue
usb: musb: Add missing pm_runtime_disable and drop 2430 PM timeout
usb: musb: Fix PM for hub disconnect
usb: musb: Fix sleeping function called from invalid context for hdrc glue
usb: musb: Fix broken use of static variable for multiple instances
USB: serial: cp210x: add ID for the Zone DPMX
usb: chipidea: move the lock initialization to core file
Fix USB CB/CBI storage devices with CONFIG_VMAP_STACK=y
USB: serial: ftdi_sio: add support for TI CC3200 LaunchPad
Pull HID fixes from Jiri Kosina:
- DMA-on-stack fixes for a couple drivers, from Benjamin Tissoires
- small memory sanitization fix for sensor-hub driver, from Song
Hongyan
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-sensor-hub: clear memory to avoid random data
HID: rmi: make transfer buffers DMA capable
HID: magicmouse: make transfer buffers DMA capable
HID: lg: make transfer buffers DMA capable
HID: cp2112: make transfer buffers DMA capable
KVM was using arrays of size KVM_MAX_VCPUS with vcpu_id, but ID can be
bigger that the maximal number of VCPUs, resulting in out-of-bounds
access.
Found by syzkaller:
BUG: KASAN: slab-out-of-bounds in __apic_accept_irq+0xb33/0xb50 at addr [...]
Write of size 1 by task a.out/27101
CPU: 1 PID: 27101 Comm: a.out Not tainted 4.9.0-rc5+ #49
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
[...]
Call Trace:
[...] __apic_accept_irq+0xb33/0xb50 arch/x86/kvm/lapic.c:905
[...] kvm_apic_set_irq+0x10e/0x180 arch/x86/kvm/lapic.c:495
[...] kvm_irq_delivery_to_apic+0x732/0xc10 arch/x86/kvm/irq_comm.c:86
[...] ioapic_service+0x41d/0x760 arch/x86/kvm/ioapic.c:360
[...] ioapic_set_irq+0x275/0x6c0 arch/x86/kvm/ioapic.c:222
[...] kvm_ioapic_inject_all arch/x86/kvm/ioapic.c:235
[...] kvm_set_ioapic+0x223/0x310 arch/x86/kvm/ioapic.c:670
[...] kvm_vm_ioctl_set_irqchip arch/x86/kvm/x86.c:3668
[...] kvm_arch_vm_ioctl+0x1a08/0x23c0 arch/x86/kvm/x86.c:3999
[...] kvm_vm_ioctl+0x1fa/0x1a70 arch/x86/kvm/../../../virt/kvm/kvm_main.c:3099
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Fixes: af1bae5497 ("KVM: x86: bump KVM_MAX_VCPU_ID to 1023")
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
em_jmp_far and em_ret_far assumed that setting IP can only fail in 64
bit mode, but syzkaller proved otherwise (and SDM agrees).
Code segment was restored upon failure, but it was left uninitialized
outside of long mode, which could lead to a leak of host kernel stack.
We could have fixed that by always saving and restoring the CS, but we
take a simpler approach and just break any guest that manages to fail
as the error recovery is error-prone and modern CPUs don't need emulator
for this.
Found by syzkaller:
WARNING: CPU: 2 PID: 3668 at arch/x86/kvm/emulate.c:2217 em_ret_far+0x428/0x480
Kernel panic - not syncing: panic_on_warn set ...
CPU: 2 PID: 3668 Comm: syz-executor Not tainted 4.9.0-rc4+ #49
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
[...]
Call Trace:
[...] __dump_stack lib/dump_stack.c:15
[...] dump_stack+0xb3/0x118 lib/dump_stack.c:51
[...] panic+0x1b7/0x3a3 kernel/panic.c:179
[...] __warn+0x1c4/0x1e0 kernel/panic.c:542
[...] warn_slowpath_null+0x2c/0x40 kernel/panic.c:585
[...] em_ret_far+0x428/0x480 arch/x86/kvm/emulate.c:2217
[...] em_ret_far_imm+0x17/0x70 arch/x86/kvm/emulate.c:2227
[...] x86_emulate_insn+0x87a/0x3730 arch/x86/kvm/emulate.c:5294
[...] x86_emulate_instruction+0x520/0x1ba0 arch/x86/kvm/x86.c:5545
[...] emulate_instruction arch/x86/include/asm/kvm_host.h:1116
[...] complete_emulated_io arch/x86/kvm/x86.c:6870
[...] complete_emulated_mmio+0x4e9/0x710 arch/x86/kvm/x86.c:6934
[...] kvm_arch_vcpu_ioctl_run+0x3b7a/0x5a90 arch/x86/kvm/x86.c:6978
[...] kvm_vcpu_ioctl+0x61e/0xdd0 arch/x86/kvm/../../../virt/kvm/kvm_main.c:2557
[...] vfs_ioctl fs/ioctl.c:43
[...] do_vfs_ioctl+0x18c/0x1040 fs/ioctl.c:679
[...] SYSC_ioctl fs/ioctl.c:694
[...] SyS_ioctl+0x8f/0xc0 fs/ioctl.c:685
[...] entry_SYSCALL_64_fastpath+0x1f/0xc2
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Fixes: d1442d85cc ("KVM: x86: Handle errors when RIP is set during far jumps")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Otherwise each individual rotator char would be printed in a new line:
(...)
[ 0.642350] -
[ 0.644374] |
[ 0.646367] -
(...)
Signed-off-by: Nicolas Schichan <nicolas.schichan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an ipv6 address has the tentative flag set, it can't be
used as source for egress traffic, while the associated route,
if any, can be looked up and even stored into some dst_cache.
In the latter scenario, the source ipv6 address selected and
stored in the cache is most probably wrong (e.g. with
link-local scope) and the entity using the dst_cache will
experience lack of ipv6 connectivity until said cache is
cleared or invalidated.
Overall this may cause lack of connectivity over most IPv6 tunnels
(comprising geneve and vxlan), if the first egress packet reaches
the tunnel before the DaD is completed for the used ipv6
address.
This patch bumps a new genid after that the IFA_F_TENTATIVE flag
is cleared, so that dst_cache will be invalidated on
next lookup and ipv6 connectivity restored.
Fixes: 0c1d70af92 ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd7 ("geneve: add dst caching support")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to generate trace events for mdio read and write accesses.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VMware VMCI transport supports loopback inside virtual machines.
This patch implements loopback for virtio-vsock.
Flow control is handled by the virtio-vsock protocol as usual. The
sending process stops transmitting on a connection when the peer's
receive buffer space is exhausted.
Cathy Avery <cavery@redhat.com> noticed this difference between VMCI and
virtio-vsock when a test case using loopback failed. Although loopback
isn't the main point of AF_VSOCK, it is useful for testing and
virtio-vsock must match VMCI semantics so that userspace programs run
regardless of the underlying transport.
My understanding is that loopback is not supported on the host side with
VMCI. Follow that by implementing it only in the guest driver, not the
vhost host driver.
Cc: Jorgen Hansen <jhansen@vmware.com>
Reported-by: Cathy Avery <cavery@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading the TX fifo to receive bytes on the I2C bus, we incorrectly
count the number of bytes:
rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR);
while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) {
if (rx_limit - dev->rx_outstanding <= 0)
break;
rx_limit--;
dev->rx_outstanding++;
}
DW_IC_RXFLR indicates how many bytes are available to be read in the
FIFO, dev->rx_fifo_depth is the FIFO size, and dev->rx_outstanding is
the number of bytes that we've requested to be read so far, but which
have not been read.
Firstly, increasing dev->rx_outstanding and decreasing rx_limit and then
comparing them results in each byte consuming "two" bytes in this
tracking, so this is obviously wrong.
Secondly, the number of bytes that _could_ be received into the FIFO at
any time is the number of bytes we have so far requested but not yet
read from the FIFO - in other words dev->rx_outstanding.
So, in order to request enough bytes to fill the RX FIFO, we need to
request dev->rx_fifo_depth - dev->rx_outstanding bytes.
Modifying the code thusly results in us reaching the maximum number of
bytes outstanding each time we queue more "receive" operations, provided
the transfer allows that to happen.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rather than reporting success for a short transfer due to interrupt
latency, report an error both to the caller, as well as to the kernel
log.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe function requests the interrupt before initializing
the ddp component. Which leads to a null pointer dereference at boot.
Fix this by requesting the interrput after all components got
initialized properly.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC
MT8173.")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Change-Id: I57193a7ab554dfb37c35a455900689333adf511c
Tune dsi frame rate by pixel clock, dsi add some extra signal (i.e.
Tlpx, Ths-prepare, Ths-zero, Ths-trail,Ths-exit) when enter and exit LP
mode, those signals will cause h-time larger than normal and reduce FPS.
So need to multiply a coefficient to offset the extra signal's effect.
coefficient = ((htotal*bpp/lane_number)+Tlpx+Ths_prep+Ths_zero+
Ths_trail+Ths_exit)/(htotal*bpp/lane_number)
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
If we want to set the hardware OD to relay mode,
we have to set DISP_OD_CFG register rather than
OD_RELAYMODE; otherwise, the system will access
the wrong address.
Change-Id: Ifb9bb4caa63df906437d48b5d5326b6d04ea332a
Fixes: 7216436420 ("drm/mediatek: set mt8173 dithering function")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
When configured with CONFIG_PPC_EARLY_DEBUG_OPAL=y the kernel expects
the OPAL entry and base addresses to be passed in r8 and r9
respectively. Currently the wrapper does not attempt to restore these
values before entering the decompressed kernel which causes the kernel
to branch into whatever happens to be in r9 when doing a write to the
OPAL console in early boot.
This patch adds a platform_ops hook that can be used to branch into the
new kernel. The OPAL console driver patches this at runtime so that if
the console is used it will be restored just prior to entering the
kernel.
Fixes: 656ad58ef1 ("powerpc/boot: Add OPAL console to epapr wrappers")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure mlx4_en_free_resources is called under the netdev state lock.
This is needed since RCU dereference of XDP prog should be protected.
Fixes: 326fe02d1e ("net/mlx4_en: protect ring->xdp_prog with rcu_read_lock")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Sagi Grimberg <sagi@grimberg.me>
CC: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7c6ae610a1, because l2tp_xmit_skb() never
returns NET_XMIT_CN, it ignores the return value of l2tp_xmit_core().
Cc: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RT netlink, calcit() function should return the minimal size for
netlink dump message. This will make sure that dump message for every
network device can be stored.
Currently, rtnl_calcit() function doesn't account the size of header of
netlink message, this patch will fix it.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing that:
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_VXLAN (0x1UL << 0)
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_GENEVE (0x5UL << 0)
and that 'bnxt_hwrm_tunnel_dst_port_alloc()' is only called with one of
these 2 constants, the TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_GENEVE can not
trigger.
Replace the bit test that overlap by an equality test, just as in
'bnxt_hwrm_tunnel_dst_port_free()' above.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning in <linux/netdevice.h> (missing ':'):
..//include/linux/netdevice.h:1904: warning: No description found for parameter 'prio_tc_map[TC_BITMASK + 1]'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_set_promiscuity failed in macvlan_open, it always invokes
dev_set_allmulti without checking if necessary.
Now check the IFF_ALLMULTI flag firstly before rollback the multicast
setting in the error handler.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix setting of SUPPORTED_FIBRE bit as it was not present in features
of KSZ8041.
Signed-off-by: Kirill Esipov <yesipov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A late issue discovered by Russell King while testing his setup on Juno.
* 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld:
drm/arm: hdlcd: fix plane base address update
one small powerplay fix and one regression fix for older PX systems and d3cold
* 'drm-fixes-4.9' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix power state when port pm is unavailable (v2)
drm/amdgpu: fix power state when port pm is unavailable
drm/amd/powerplay: avoid out of bounds access on array ps.
The commit 8dfbcc4351 ("[media] xc2028: avoid use after free") tried
to address the reported use-after-free by clearing the reference.
However, it's clearing the wrong pointer; it sets NULL to
priv->ctrl.fname, but it's anyway overwritten by the next line
memcpy(&priv->ctrl, p, sizeof(priv->ctrl)).
OTOH, the actual code accessing the freed string is the strcmp() call
with priv->fname:
if (!firmware_name[0] && p->fname &&
priv->fname && strcmp(p->fname, priv->fname))
free_firmware(priv);
where priv->fname points to the previous file name, and this was
already freed by kfree().
For fixing the bug properly, this patch does the following:
- Keep the copy of firmware file name in only priv->fname,
priv->ctrl.fname isn't changed;
- The allocation is done only when the firmware gets loaded;
- The kfree() is called in free_firmware() commonly
Fixes: commit 8dfbcc4351 ('[media] xc2028: avoid use after free')
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stable Bugfixes:
- Hide array-bounds warning
Bugfixes:
- Keep a reference on lock states while checking
- Handle NFS4ERR_OLD_STATEID in nfs4_reclaim_open_state
- Don't call close if the open stateid has already been cleared
- Fix CLOSE rases with OPEN
- Fix a regression in DELEGRETURN
-----BEGIN PGP SIGNATURE-----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=YhQv
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.9-4' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client bugfixes from Anna Schumaker:
"Most of these fix regressions or races, but there is one patch for
stable that Arnd sent me
Stable bugfix:
- Hide array-bounds warning
Bugfixes:
- Keep a reference on lock states while checking
- Handle NFS4ERR_OLD_STATEID in nfs4_reclaim_open_state
- Don't call close if the open stateid has already been cleared
- Fix CLOSE rases with OPEN
- Fix a regression in DELEGRETURN"
* tag 'nfs-for-4.9-4' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFSv4.x: hide array-bounds warning
NFSv4.1: Keep a reference on lock states while checking
NFSv4.1: Handle NFS4ERR_OLD_STATEID in nfs4_reclaim_open_state
NFSv4: Don't call close if the open stateid has already been cleared
NFSv4: Fix CLOSE races with OPEN
NFSv4.1: Fix a regression in DELEGRETURN
Pull arch/tile bugfix from Chris Metcalf:
"This fixes a bug that causes reboots after 208 days of uptime :-)"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: avoid using clocksource_cyc2ns with absolute cycle count
For large values of "mult" and long uptimes, the intermediate
result of "cycles * mult" can overflow 64 bits. For example,
the tile platform calls clocksource_cyc2ns with a 1.2 GHz clock;
we have mult = 853, and after 208.5 days, we overflow 64 bits.
Since clocksource_cyc2ns() is intended to be used for relative
cycle counts, not absolute cycle counts, performance is more
importance than accepting a wider range of cycle values. So,
just use mult_frac() directly in tile's sched_clock().
Commit 4cecf6d401 ("sched, x86: Avoid unnecessary overflow
in sched_clock") by Salman Qazi results in essentially the same
generated code for x86 as this change does for tile. In fact,
a follow-on change by Salman introduced mult_frac() and switched
to using it, so the C code was largely identical at that point too.
Peter Zijlstra then added mul_u64_u32_shr() and switched x86
to use it. This is, in principle, better; by optimizing the
64x64->64 multiplies to be 32x32->64 multiplies we can potentially
save some time. However, the compiler piplines the 64x64->64
multiplies pretty well, and the conditional branch in the generic
mul_u64_u32_shr() causes some bubbles in execution, with the
result that it's pretty much a wash. If tilegx provided its own
implementation of mul_u64_u32_shr() without the conditional branch,
we could potentially save 3 cycles, but that seems like small gain
for a fair amount of additional build scaffolding; no other platform
currently provides a mul_u64_u32_shr() override, and tile doesn't
currently have an <asm/div64.h> header to put the override in.
Additionally, gcc currently has an optimization bug that prevents
it from recognizing the opportunity to use a 32x32->64 multiply,
and so the result would be no better than the existing mult_frac()
until such time as the compiler is fixed.
For now, just using mult_frac() seems like the right answer.
Cc: stable@kernel.org [v3.4+]
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
When PCIe port PM is not enabled (system BIOS is pre-2015 or the
pcie_port_pm=off parameter is set), legacy ATPX PM should still be
marked as supported. Otherwise the GPU can fail to power on after
runtime suspend. This affected a Dell Inspiron 5548.
Ideally the BIOS date in the PCI core is lowered to 2013 (the first year
where hybrid graphics platforms using power resources was introduced),
but that seems more risky at this point and would not solve the
pcie_port_pm=off issue.
v2: agd: fix typo
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98505
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org> # 4.8+
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
When PCIe port PM is not enabled (system BIOS is pre-2015 or the
pcie_port_pm=off parameter is set), legacy ATPX PM should still be
marked as supported. Otherwise the GPU can fail to power on after
runtime suspend. This affected a Dell Inspiron 5548.
Ideally the BIOS date in the PCI core is lowered to 2013 (the first year
where hybrid graphics platforms using power resources was introduced),
but that seems more risky at this point and would not solve the
pcie_port_pm=off issue.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98505
Reported-and-tested-by: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org> # 4.8+
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
When user tried to read some fields like hysteresis from IIO sysfs on some
systems, it fails. The reason is that this field is a byte field and caller
of sensor_hub_get_feature() passes a buffer of 4 bytes. Here the function
sensor_hub_get_feature() copies the single byte from the report to the
caller buffer and returns "1" as the number of bytes copied. So caller
can use the return value.
But this is done by multiple callers, so if we just change the
sensor_hub_get_feature so that caller buffer is initialized with 0s
then we don't to change all functions.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove
buffers allocated on the stack.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove
buffers allocated on the stack.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove
buffers allocated on the stack.
[jkosina@suse.cz: fix up second usage of hid_hw_raw_request(), spotted by
0day build bot]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel v4.9 strictly enforces DMA capable buffers, so we need to remove
buffers allocated on the stack.
Use a spinlock to prevent concurrent accesses to the buffer.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull perf fixes from Ingo Molnar:
"Six fixes for bugs that were found via fuzzing, and a trivial
hw-enablement patch for AMD Family-17h CPU PMUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Allow only a single PMU/box within an events group
perf/x86/intel: Cure bogus unwind from PEBS entries
perf/x86: Restore TASK_SIZE check on frame pointer
perf/core: Fix address filter parser
perf/x86: Add perf support for AMD family-17h processors
perf/x86/uncore: Fix crash by removing bogus event_list[] handling for SNB client uncore IMC
perf/core: Do not set cpuctx->cgrp for unscheduled cgroups
Sending frames in CCK rates on HT can cause performance problems.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
