* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (64 commits)
debugfs: use specified mode to possibly mark files read/write only
debugfs: Fix terminology inconsistency of dir name to mount debugfs filesystem.
xen: remove driver_data direct access of struct device from more drivers
usb: gadget: at91_udc: remove driver_data direct access of struct device
uml: remove driver_data direct access of struct device
block/ps3: remove driver_data direct access of struct device
s390: remove driver_data direct access of struct device
parport: remove driver_data direct access of struct device
parisc: remove driver_data direct access of struct device
of_serial: remove driver_data direct access of struct device
mips: remove driver_data direct access of struct device
ipmi: remove driver_data direct access of struct device
infiniband: ehca: remove driver_data direct access of struct device
ibmvscsi: gadget: at91_udc: remove driver_data direct access of struct device
hvcs: remove driver_data direct access of struct device
xen block: remove driver_data direct access of struct device
thermal: remove driver_data direct access of struct device
scsi: remove driver_data direct access of struct device
pcmcia: remove driver_data direct access of struct device
PCIE: remove driver_data direct access of struct device
...
Manually fix up trivial conflicts due to different direct driver_data
direct access fixups in drivers/block/{ps3disk.c,ps3vram.c}
After enabling hardware flow control, any subsequent termios call may hang
waiting for the transmitter to drain. This appears to be caused by a
busy-loop in set_termios() waiting for the transmitter to become empty,
which may take a very long time (or hang indefinitely) if the device at
the other end is blocking us.
A quick look through the tty and serial_core code indicates that any
necessary flushing (which is optional) has already been done at this
point, so there's no need for the driver to flush the transmitter on its
own.
Fix it by removing the busy-loop altogether.
Tested-by: Eirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
real baud rate may be different from the one requested.
for upper layers, set the nearest value to the real rate
in favour of the rate previously requested.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using the iMX serial driver with an IrDA device
needs extra peripheral settings and specific
timing depending on the transmitter circuitry used.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for calculation of numerator and denominator
used in baud rate setting, use generic library function
for optimum settings.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
correctly de-initialise device when setting up failed,
call to pdata->exit() was missing.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
needed to avoid continued transmission by hardware
while software already shuts down, which might
cause dangling characters to show up in hardware
queues when restarting the device.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
upper layers, namely line discipline, need to be notified
when transmission of more data is possible. For spurious
cases, where IRQ handling does not supply notification
for sure, it is given additionally here, when data has just
been transmitted and space in the buffer will most probably
be available.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"have_rtscts" is assigned 1, while it is declared
int:1, two's complement, which can hold 0 and -1
only. The code works, as the upper bits are cut
off, and tests are done against 0 only.
Nonetheless, correctly declaring the bit field
as unsigned int:1 renders the code more robust.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver only handles speeds but it fails to return the current values
for the hardware features it does not support.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver for the UART found in the Timberdale FPGA
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UART RX handling code isn't exactly speeding, so don't go disabling
all interrupts when processing the buffer. Just disable the relevant DMA
interrupt. This greatly improves latency of the system when utilizing the
UART.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
05000231 - UART STB Bit Incorrectly Affects Receiver Setting
For processors affected by this, we cannot safely allow CSTOPB to be set
as the UART will then be unable to properly clock in bytes.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some comments for how these anomalies are addressed:
05000215 - UART TX Interrupt Masked Erroneously
We always clear ETBEI within last UART TX interrupt to end
a string. It is always set when starting a new tx transfer.
05000099 - UART Line Status Register (UART_LSR) Bits Are Not Updated at
the Same Time
This anomaly affects driver only in POLL code where multi bits of
UART_LSR are checked. It doesn't affect current bfin_5xx.c driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug is caused by irregular behavior of DMA register CURR_X_COUNT
and CURR_Y_COUNT when an auto restart uart rx DMA run to last byte in
DMA buffer, trigger the interrupt and stay at this possiton. The status
of current x and y is 0:7 instead of 512:8 or 0:8. The driver doesn't
take care of this case when calculating the position.
URL: http://blackfin.uclinux.org/gf/tracker/5063
Reported-by: Tomasz Motylewski <t.motylewski@bfad.de>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a SSYNC() into bfin_serial_dma_tx_chars() to ensure DMA registers are
written with new data otherwise we might miss a byte or two when the
system is under load. PIO mode is OK though.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we already setup the early console UART in
arch/blackfin/kernel/early_printk.c, and common functions which are
enabled from the .setup will override the proper settings later, don't
fill in these structures. Otherwise we get mangled baudrate settings when
using early_printk.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ignore receiving data if new position is in the same line of current
buffer tail and is small. This should decrease overruns.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hopefuly the new version is easier to read, but in the process it declares
proper clobber lists and better constraints so that GCC can do a better
job at allocating free registers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPORT transmit frame sync (TFS) isn't used as an electrical signal during
normal SPORT UART emulation. However, it is useful in EIA RS-485
emulation as RS-485 Transceiver Driver Enable DE strobe.
This patch configures:
TFS to be active high in order to drive an DE strobe of
an eventually connected RS-485 Transceiver.
Late frame sync mode (LATFS) gating the entire TX shift cycle.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the TI AR7 internal UART.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As it is, defining ICOM_TRACE produces some compile errors, as
"parameter name omitted" and "redefinition of ‘trace’"
This patch removes the wrong trace definition.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
adapter->version can only be ADAPTER_V2 or ADAPTER_V1. So,
that OR operand in the "if" clause is non-sense and can be removed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there are more then one 4/8-port board jsm_uart_port_init
allocate a line numbers of the second and further boards
from range of previous one.
This patch fixed the problem.
Signed-off-by: Alexander Y. Fomichev <git.user@gmail.com>
[printks fixed to add jsm: ]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the following serial controller chip:
Oxford Semiconductor OXCB950 for PCI Cardbus interface
http://www.transdimension.com/products/serial/OXCB950.html
on this card:
ExSys EX-1370 1 port high-speed serial card for ExpressCard/34 slot
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Nomadik 8815 SoC has a slightly modified version of the PL011 block.
The patch uses the different ID value as a key to select a vendor
structure that is used to keep track of the differences, as suggested
by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix SCI transmission sequence in console output function.
This reorders the write sequence to match the SH-3 manual, and corrects
a console corruption bug observed on SH-3 SCI.
Signed-off-by: Toshinobu Sugioka <sugioka@itonet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If you setserial a port which has never been initialised we change the type
but don't update the I/O method pointers. The same problem is true if you
change the io type of a port - but nobody ever does that so nobody noticed!
Remember the old type and when attaching if the type has changed reload the
port accessor pointers. We can't do it blindly as some 8250 drivers load custom
accessors and we must not stomp those.
Tested-by: Victor Seryodkin <vvscore@gmail.com>
Closes-bug: #13367
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/serial/8250_gsc.c:44: warning: format '%lx' expects type
'long unsigned int', but argument 2 has type 'resource_size_t'
[akpm@linux-foundation.org: fix it to handle u64's]
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The check for an overindexing of mpc52xx_uart_{ports,nodes} has an
off-by-one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
