When VGA decodes change we need to do a bit more evaluation of exactly what
has changed. We don't necessarily give up all the old owns resources and
we need to account for resources with locks. The new algorithm is: If
something is added, update decodes. If legacy resources were added and
none were there before, we have a new participant. If something is
removed, update decodes. If we previously owned it, we no longer own it.
If it was previously locked, invalidate all locks and release it. If
legacy resources were removed and none are left, remove the participant
from VGA arbitration.
Previously we updated decodes, released ownership of everything that was
previously decoded, ignored all locks, and went off looking for another
device to transfer VGA to. In a test case where Intel IGD removes only
legacy VGA memory decoding, this left the arbiter switching to discrete
graphics without actually disabling legacy VGA IO from the IGD. As a
bonus, we bumped up the count of VGA arbitration participants for no
good reason.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Kill now unused variables, reported by the 0-day kernel
builtbot.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a device does not own a resource then we don't need to disable it.
This resolves the case where an Intel IGD device can be configured to
disable decode of VGA memory but we still need the arbiter to handle
VGA I/O port routing. When the IGD device is in conflict, only
PCI_COMMAND_IO should be disabled since VGA memory does not require
arbitration on this device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we attempt to kmalloc after calling get_pages, there is a possibility
that the shrinker may reap the pages we just acquired. To prevent this
we need to increment the pages_pin_count early, so rearrange the code
and error paths to make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We shouldn't disable the trickle feed bits on Haswell. Our
documentation explicitly says the trickle feed bits of PRI_CTL and
CUR_CTL should not be programmed to 1, and the hardware engineer also
asked us to not program the SPR_CTL field to 1. Leaving the bits as 1
could cause underflows.
Reported-by: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Systems with Intel graphics controllers set aside memory exclusively for
gfx driver use. This memory is not always marked in the E820 as
reserved or as RAM, and so is subject to overlap from E820 manipulation
later in the boot process. On some systems, MMIO space is allocated on
top, despite the efforts of the "RAM buffer" approach, which simply
rounds memory boundaries up to 64M to try to catch space that may decode
as RAM and so is not suitable for MMIO.
v2: use read_pci_config for 32 bit reads instead of adding a new one
(Chris)
add gen6 stolen size function (Chris)
v3: use a function pointer (Chris)
drop gen2 bits (Daniel)
v4: call e820_sanitize_map after adding the region
v5: fixup comments (Peter)
simplify loop (Chris)
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66726
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66844
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For use by userspace (at some point in the future) and other kernel code.
v2: move PCI IDs to uabi (Chris)
move PCI IDs to drm/ (Dave)
v3: fixup Quanta detection - needs to come first (Daniel)
v4: fix up PCI match structure init for easier use by userspace (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The helper exists, might as well use it instead of __GFP_ZERO.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RCS flips do work on Iybridge+ so long as we can unmask the messages
through DERRMR. However, there are quite a few workarounds mentioned
regarding unmasking more than one event or triggering more than one
message through DERRMR. Those workarounds in principle prevent us from
performing pipelined flips (and asynchronous flips across multiple
planes) and equally apply to the "known good" BCS ring. Given that it
already appears to work, and also appears to work with unmasking all 3
planes at once (and queuing flips across multiple planes), be brave.
Bugzlla: https://bugs.freedesktop.org/show_bug.cgi?id=67600
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Lightly-tested-by: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Cc: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now have more devices using ring->private than not, and they all want
the same structure. Worse, I would like to use a scratch page from
outside of intel_ringbuffer.c and so for convenience would like to reuse
ring->private. Embed the object into the struct intel_ringbuffer so that
we can keep the code clean.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If need to enable the panel fitter, the crtc timings have to be
programmed according to the panel's native (fixed) mode. This isn't the
case atm, since after the encoder changes adjusted_mode to fixed
mode the crtc_* timing fields of adjusted_mode will stay at their original
non-native values that the user passed in. This results in a corrupted
output.
One exception is when we have a second pass of computing encoder configs
due to bandwidth limitation, since then we'll set adjusted_mode.crtc_*
fields to the fixed mode values set in the first pass; so in this case
things will work out.
Fix this by updating the adjusted_mode.crtc_* fields when we set the
fixed panel mode.
This regression has been introduced in
commit 135c81b8c3
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 21 21:37:09 2013 +0200
drm/i915: clean up crtc timings computation
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already have a big splashing *ERROR* for all the relevant cases of
hangs, so this one here is redudant. And it results in an unclean
dmesg when running with simulated hangs. Regression has been
introduced in
commit 05407ff889
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu May 30 09:04:29 2013 +0300
drm/i915: detect hang using per ring hangcheck_score
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68641
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It can be useful to compare at times the current vs requested frequency
of the GPU, so provide the contents of RPNSWREQ alonside CAGF.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It appears that Valleyview shares its VGA encoder with more recent
siblings and requires the same forced detection cycle after a hardware
reset before we can rely on hotplugging.
Reported-and-tested-by: kobeqin <kobe.qin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67733
Tested-by: kobeqin <kobe.qin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Check for gen >= 5 insted, acked by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Valleyview has its own render power state implementation with different
capability knobs - it has no RP0,RP1,RPn but rather RPe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67734
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: kobe.qin@intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In reset we try to restore the forcewake state to
pre reset state, using forcewake_count. The reset
doesn't seem to clear the forcewake bits so we
get warn on forcewake ack register not clearing.
Use same mechanism as intel_uncore_sanitize() does
when loading driver to reset the forcewake bits, right
after the chip has been reset.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Submitting a batchbuffer which simulates a gpu
hang by doing MI_BATCH_BUFFER_START into itself,
to test hangcheck, started to hard hang the whole box
(IVB). Bisecting lead to this commit:
commit 664b422c2966cd39b8f67e8d53a566ea8c877cd6
Author: Vinit Azad <vinit.azad@intel.com>
Date: Wed Aug 14 13:34:33 2013 -0700
drm/i915: Only unmask required PM interrupts
Experimenting with the mask register showed that
unmasking EI UP will prevent the hard hang in IVB and SNB.
HSW doesn't hang with EI UP masked.
Considering we are just disabling interrupts that aren't even
delivered to driver, this change is more likely to paper over some
weirdness in gpu's internal state machine. But until better
explanation can be found, let's trade little bit of power
for stability on these architectures.
v2: - Unmask EI_EXPIRED directly in I915_WRITE (Vinit)
v3: - Only unmask on SNB and IVB
Cc: Vinit Azad <vinit.azad@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Vinit Azad <vinit.azad@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable support for drm render nodes for radeon by flagging the ioctls that
are safe and just needed for rendering.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Enable support for drm render nodes for nouveau by flagging the ioctls that
are safe and just needed for rendering.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Enable support for drm render nodes for i915 by flagging the ioctls that
are safe and just needed for rendering.
v2: mark reg_read, set_caching and get_caching (ickle, danvet)
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DRM_IOCTL_MODE_GETFB is used to retrieve information about a given
framebuffer ID. It is a read-only helper and was thus declassified for
unprivileged access in:
commit a14b1b4247
Author: Mandeep Singh Baines <mandeep.baines@gmail.com>
Date: Fri Jan 20 12:11:16 2012 -0800
drm: remove master fd restriction on mode setting getters
However, alongside width, height and stride information,
DRM_IOCTL_MODE_GETFB also passes back a handle to the underlying buffer of
the framebuffer. This handle allows users to mmap() it and read or write
into it. Obviously, this should be restricted to DRM-Master.
With the current setup, *any* process with access to /dev/dri/card0 (which
means any process with access to hardware-accelerated rendering) can
access the current screen framebuffer and modify it ad libitum.
For backwards-compatibility reasons we want to keep the
DRM_IOCTL_MODE_GETFB call unprivileged. Besides, it provides quite useful
information regarding screen setup. So we simply test whether the caller
is the current DRM-Master and if not, we return 0 as handle, which is
always invalid. A following DRM_IOCTL_GEM_CLOSE on this handle will fail
with EINVAL, but we accept this. Users shouldn't test for errors during
GEM_CLOSE, anyway. And it is still better as a failing MODE_GETFB call.
v2: add capable(CAP_SYS_ADMIN) check for compatibility with i-g-t
Cc: <stable@vger.kernel.org>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Drop the msm_connector base class, and special calls to base class
methods from the encoder, and use instead drm_bridge. This allows for a
cleaner division between the hdmi (and in future dsi) blocks, from the
mdp block.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds the notion of a drm_bridge. A bridge is a chained
device which hangs off an encoder. The drm driver using the bridge
should provide the association between encoder and bridge. Once a
bridge is associated with an encoder, it will participate in mode
set, and dpms (via the enable/disable hooks).
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Check to make sure the dc limits are valid before using them.
Some systems may not have a dc limits table. In that case just
use the ac limits. This fixes hangs on systems when the power
state is changed when on battery (dc) due to invalid performance
state parameters.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=68708
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check to make sure the dc limits are valid before using them.
Some systems may not have a dc limits table. In that case just
use the ac limits. This fixes hangs on systems when the power
state is changed when on battery (dc) due to invalid performance
state parameters.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=68708
v2: fix up limits in dpm_init()
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The same as on evergreen.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reported-by: FrankR Huang <FrankR.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The vram scratch buffer needs to be initialized
before the mc is programmed otherwise we program
0 as the GPU address of the default GPU fault
page. In most cases we put vram at zero anyway and
reserve a page for the legacy vga buffer so in practice
this shouldn't cause any problems, but better to make
it correct.
Was changed in:
6fab3febf6
Reported-by: FrankR Huang <FrankR.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Avoid needless uvd reprogramming if uvd powergating is disabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
No need to try the ring tests if starting the UVD block failed.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
For powergating, we just need to re-init the registers, there
is no need to restore the uvd BOs. This just adds needless
work when powergating uvd for playback while the system is
on. We only need to restore the uvd BOs on an actual resume
from suspend or when the driver loads.
This fixes multi-stream UVD playback on KB systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
The table has the following format:
typedef struct _ATOM_SRC_DST_TABLE_FOR_ONE_OBJECT //usSrcDstTableOffset pointing to this structure
{
UCHAR ucNumberOfSrc;
USHORT usSrcObjectID[1];
UCHAR ucNumberOfDst;
USHORT usDstObjectID[1];
}ATOM_SRC_DST_TABLE_FOR_ONE_OBJECT;
usSrcObjectID[] and usDstObjectID[] are variably sized, so we
can't access them directly. Use pointers and update the offset
appropriately when accessing the Dst members.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Setting MC_MISC_CNTL.GART_INDEX_REG_EN causes hangs on
some boards on resume. The systems seem to work fine
without touching this bit so leave it as is.
v2: read-modify-write the GART_INDEX_REG_EN bit.
I suspect the problem is that we are losing the other
settings in the register.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=52952
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Daniel Tobias <dan.g.tob@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This fills in the GPU specific details for berlin
GPU cores so that the driver will work with them.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
These blocks need to be ungated for the other parts of
the driver properly initialize them (e.g., after a gpu
reset, etc.).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
