* remove redundant svwks_ide_dma_end() [ __ide_dma_end() is used by default ]
* remove init_dma_svwks() so the default ide_setup_dma() function is used
[ init_setup_csb6() takes care of not initializing disabled channels ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* BUG() on unknown DMA mode in cs5530_config_dma()
* there is no need to call hwif->ide_dma_host_{off,on}() in
cs5530_config_dma() because hwif->ide_dma_host_{off,on}()
is called by hwif->ide_dma_off_{quietly,on}()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In drivers/ide/Kconfig BLK_DEV_TRM290 depends on
BLK_DEV_IDEDMA_PCI (on which is BLK_DEV_IDEDMA dependant on).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is the patch (based on 2.6.19-rc4) for PATA controller of
Toshiba Cell reference set(Celleb). The reference set consists
of Cell, 512MB memory, Super Companion Chip(SCC) and some
peripherals such as HDD, GbE, etc. You can see brief explanation
and picture of Cell reference set at following URLs.
http://www.toshiba.co.jp/about/press/2005_09/pr2001.htmhttp://cell-industries.com/toshiba_announces.php
We use a drivers/ide driver because its design is more suitable for
SCC IDE controller than libata driver. Since SCC supports only 32bit
read/write, we must override many callbacks of ata_port_operations
by modifying generic helpers. Each time the libata common code is
updated, we must update those modified helpers. It is very hard for us.
But we will try to implement the libata driver as needed.
Signed-off-by: Kou Ishizaki <kou.ishizaki at toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi at toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix a number of issues with the DMA support code:
- driver claims support for all SW/MW DMA modes while supporting only MWDMA2;
- ide_dma_check() method tries to enable DMA on the "known good" drives which
don't support MWDMA2;
- ide_dma_on() method upon failure to set drive to MWDMA2 re-tunes already
tuned PIO mode and calls ide_dma_off() method instead of returning error;
- ide_dma_off() method sets drive->current_speed while it doesn't actually
change (only the PIO timings are re-loaded into the chip's registers);
- init_hwif() method forcibly sets/resets both "drive DMA capable" bits while
this is properly handled by ide_dma_{on,off}() methods being called later...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the driver's tuneproc() method to always set the PIO mode requested and not
pick the best possible one, rename it to pdc202xx_tune_drive(), and change the
calls to it accordingly; remove the preceding comment which has nothing to do
with the code.
Sergei Shtylyov wrote:
> The tuneproc() method should take arg 255 for auto-selecting the best PIO
> mode, not 5 as it did here + this driver's method always auto-selected instead
> of setting the mode it's been told to -- issue typical to drivers/ide/...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix two typos found by SiI680A documentation check. They caused the taskfile
transfer overclocking:
- in PIO mode 1 as 0x2283 must be used for both data and taskfile transfers;
- in PIO mode 2 as data and taskfile timings are swapped when writing to the
MMIO regs.
Fix coding style and trailing whitespace in enclosing statements while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drivers/ide/pci/siimage.c | 59 ++++++++++++++++++++++------------------------
1 file changed, 29 insertions(+), 30 deletions(-)
patch 2/2:
Remove clearing bmdma status from cdrom_decode_status() since ATA devices
might need it as well.
(http://lkml.org/lkml/2006/12/4/201 and http://lkml.org/lkml/2006/11/15/94)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
patch 1/2 (revised):
- Fix drive->waiting_for_dma to work with CDB-intr devices.
- Do the dma status clearing in ide_intr() and add a new
hwif->ide_dma_clear_irq for Intel ICHx controllers.
Revised per Alan, Sergei and Bart's advice.
Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters.
Please review/apply, thanks.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
A ZIP or similar with unformatted media will cause crashes when attempts
are made to read/write it in some cases. This is because bs_factor is
zero and we divide by it causing an oops.
As the size of a non-accessible/non-existant media is really a bit of a
zen question it doesn't matter if non-existant media is 512 bytes per
sector or zero. Setting it to 1 causes us to generate 512 bytes/sector
accesses and error properly.
Based on a fix found lurking in an ancient bugzilla entry since about 2004 (ugghhh)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* atiixp: if DMA can't be used atiixp_config_drive_for_dma() should return 0,
atiixp_dma_check() will tune the correct PIO mode anyway
* jmicron: if DMA can't be used config_chipset_for_dma() should return 0,
micron_config_drive_for_dma() will tune the correct PIO mode anyway
config_jmicron_chipset_for_pio(drive, !speed) doesn't program
device transfer mode for speed != 0 (only wastes some CPU cycles
on ide_get_best_pio_mode() call) so remove it
* triflex: if DMA can't be used triflex_config_drive_for_dma() should return 0,
triflex_config_drive_xfer_rate() will tune correct PIO mode anyway
Above changes also fix (theoretical) issue when ->speedproc fails to set
device transfer mode (i.e. when ide_config_drive_speed() fails to program it)
but one of DMA transfer modes is already enabled on the device by the BIOS.
In such scenario ide_dma_enable() will incorrectly return true statement
and ->ide_dma_check will try to enable DMA on the device.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remember to clear reg2 bits for the current device before setting mode
* remove no longer needed hpt34x_clear_chipset()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
register_platform_device_simple returns ERR_PTR(foo), so test it with
IS_ERR(foo).
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_unload_table_id() is always returning an error status.
Also, once the matching table is found, don't bother looking
for another match.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The AT91SAM9261 needs to activate an AHB clock (HCK0) to use the USB Host
controller. Previously clock.c would just enable it at startup, but now
all the unused clocks are automatically disabled.
Based on patch from Nicolas Ferre.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds another usb id to the cp2101. It seems to work well.
Please apply, thanks.
Signed-off-by: Pozsar Balazs <pozsy@uhulinux.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a runtime codespace shrink: in most cases, platform devices should
put probe() should in the init section, and remove() in the exit section.
And I have no idea why the module init/exit routines were mismarked.
It also moves one function table into read-only data.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hmm, I noticed that support for one of the USB host-to-host cables
never got fully merged ... Kconfig wouldn't show it! Fixed.
Also, changed the CDC Subset default to 'y' so that more of these
cables will work out-of-the-box.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This cleans up some error handling paths in usbnet device probing;
one of them could cause oopsing, e.g. with some RNDIS devices.
It also removes some extraneous whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Sitecom CN-124 device IDs to ALI M5632 usb host-to-host cable;
device IDs from Francois Barre <francois.barre@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
from: Kevin Lloyd <linux@sierrawireless.com>
This patch removes the Airprime 5220 device (branded as Audiovox) from
the option.c driver. This device is already supported by the sierra.c
driver.
This was based off of the option.c driver found in kernel 2.6.20-git11.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ps3_system_bus_driver_register is PS3 platform specific function.
On other platforms, it triggers WARN_ON in kref_get.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes our GTCO CalComp Interwrite IPanels from the hid-core.c blacklist
because the HID Driver properly handles them.
Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is Joris' fixes reshuffelled and features renamed as David requested.
- acm_set_control is not mandatory, honour that
- throtteling is reset upon open
- throtteling is read consistently when processing input data
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB devices do have a configuration 0, in contravention of the
USB spec. Normally 0 is supposed to indicate that a device is
unconfigured.
While we can't change what the device is doing, we can change usbcore.
This patch (as852) allows usb_set_configuration() to accept a config
value of -1 as indicating that the device should be unconfigured. The
request actually sent to the device will still contain 0 as the value.
But even if the device does have a configuration 0, dev->actconfig
will be set to NULL and dev->state will be set to USB_STATE_ADDRESS.
Without some sort of special-case handling like this, there is no way
to unconfigure these non-compliant devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The status in usb_iso_packet_descriptor should be signed, for the benefit
of someone who casts to a long or makes other benign misstep (the principle
of least surprise).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A SET_LINE_CODING control request should return a zero length packet
as an ACK to the host, during the status phase of a USB transaction.
The return value of gs_setup_class() is treated as the number of
bytes to write in the status phase of the control request, by
gs_setup(). For this case, the value returned by gs_setup_class should
be zero for SET_LINE_CODING but, right now, appears to be
sizeof(struct usb_cdc_line_coding).
However, if after doing the memcpy of the line coding descriptor we
set the variable "ret" to be zero, we should return the appropiate ZLP
to the host as an ACK in the status phase of the control request.
I've tested this out using Linux as both host and slave and confirmed
that the following small change fixes the spurious return of
sizeof(struct usb_cdc_line_coding)/wLength bytes in the status phase
of a USB_CDC_REQ_SET_LINE_CODING request. It's not a huge bug but, it
is worth fixing.
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use __u32 rather than u32 in userspace ioctl defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device will not work as a mass storage device without US_FL_IGNORE_RESIDUE.
I bought this mp3 player that takes SD cards here
http://www.aiptek.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=AX4&Category_Code=MP3&Store_Code=AS
I can provide the errors in dmesg, if necessary, but this flag was
determined as necessary by doing a quick google on the errors that were
shown in dmesg.
Signed-off-by: Dylan Taft <d13f00l@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the misspelling of "USBNET_MII" to "USB_USBNET_MII".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add CIDC USB device to HID blacklist since it is actually a USB token
and has its own driver.
Signed-off-by: Zheng XiaoJun <zhengxiaojun@hsic.com.cn>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB_RTL8150 must select MII to avoid link errors.
Stolen from a patch by Randy Dunlap.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there's a USB mass storage device which exists in two version. One
reports the correct size and the other does not. Apart from that they
are identical and cannot be told apart. Here's a heuristic based on the
empirical finding that drives have even sizes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
as the skeleton driver was made ready for autosuspend a race condition
was introduced. The reference to get device must be gotten before the
autosuspend counter is upped, as this operation may sleep, dropping BKL.
Dropping BKL means that the pointer to the device may become invalid.
Here's the fix.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch fixes endian issues in asix_tx_fixup() that prevented
AX88772 and AX88178 devices from working on big-endian systems. With
the attached patch, all three chips are reported to work on big endian.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as849) fixes a bug in the USB hub driver. A single
pre-allocated buffer is used for all port status reads, but nothing
guarantees exclusive use of the buffer. A mutex is added to provide
this guarantee.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up the error processing path: in usb_submit_urb failed, we forgot
to free buffers. Also, don't free buffers in read callback: less error
prone, 21 LOC less, no need to comment so much. N.B. write path is ok
to do kfree.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: descriptor structures have to be packed
Many of the Wireless USB decriptors added to usb_ch9.h don't have the
__attribute__((packed)) tag, and thus, they don't reflect the wire
size. This patch fixes that.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as848) adds a useful little debugging message to let us
know when ehci-hcd's bus_suspend method runs. The other HCDs have
similar messages; now ehci-hcd doesn't need to feel left out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
