"K4S281632b-1H" should read "K4S281632B-1H" (As it does everywhere
else). No more coffe!
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The second ethernet port on the Thecus n2100 was incorrectly assigned
to XINT1 instead of the correct XINT3 (PCI INTB instead of INTD), which
caused that port to be non-functional.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for KBUILD_IMAGE on ARM. This takes the usual target
specifiers (zImage/Image/etc) in the same way that powerpc does
(iow, without the arch/arm/boot prefix).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] cio: Make ccw_device_register() static.
[S390] Improve AP bus device removal.
[S390] uaccess error handling.
[S390] cio: css_probe_device() must be called enabled.
[S390] Initialize interval value to 0.
[S390] sys_getcpu compat wrapper.
efi_memory_present_wrapper() parameter start/end is physical address, but
function memory_present parameter is PFN, this patch converts physical
address to PFN.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SIGFPE signal should be generated if Division by Zero exception is detected.
Signed-off-by: Takashi Ohmasa <ohmasa.takashi@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The significand should be shifted until the value of bit [62] is 1
to normalize the denormal double number.
Signed-off-by: Takashi Ohmasa <ohmasa.takashi@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IRQ changes a while back broke the build for SMP machines.
Fix up the SMP code to use set_irq_regs/get_irq_regs as
appropriate. Also, fix a warning in arch/arm/kernel/time.c
where 'regs' becomes unused for SMP builds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Remove quirk_via_abnormal_poweroff
PCI: reset pci device state to unknown state for resume
PCI: x86-64: mmconfig missing printk levels
PCI: fix pci_fixup_video as it blows up on sparc64
acpiphp: fix latch status
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table,
teach all the architectures to use it.
This is a prerequisite for a patch which performs initcall synchronisation for
multithreaded-probing.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Added AVR32 as well ]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts much of the original pci_fixup_video change and makes it
work for all arches that need it.
fixed, and tested on x86, x86_64 and IA64 dig.
Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Consider return values for all user space access function and
return -EFAULT on error.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sscanf() could leave the interval value unchanged in which case it
would be used uninitialized.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Looking at the new syscall additions, I noticed that
sys_getcpu_wrapper wraps in to sys_tee, in what appears to be
a copy and paste error. Switch it to point to sys_getcpu..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
dp->path_component_name can be larger than ->bus_id[]
so use a different naming scheme for this stuff.
Noticed by Jurij Smakov.
Signed-off-by: David S. Miller <davem@davemloft.net>
The second argument to free_npages() was being incorrectly
calculated, which would thus access far past the end of the
arena->map[] bitmap.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) probe_other_fhcs() wants to see only non-central FHC
busses, so skip FHCs that don't sit off the root
2) Like SBUS, FHC can lack the appropriate address and
size cell count properties, so add an of_busses[]
entry and handlers for that.
3) Central FHC irq translator probing was buggy. We
were trying to use dp->child in irq_trans_init but
that linkage is not setup at this point.
So instead, pass in the parent of "dp" and look for
the child "fhc" with parent "central".
Thanks to the tireless assistence of Ben Collins in tracking
down these problems and testing out these fixes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync atstk1002_defconfig with latest git, turn off non-existent
drivers and enable a few more userspace-visible options like
SysV IPC and inotify support.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The read[bwl] and write[bwl] functions are meant for accessing PCI
devices. How this is achieved on AVR32 is unknown, as there are no
systems with a PCI bridge available yet.
On-chip peripheral access, however, should not depend on how we end
up implementing PCI access, so using __raw_read[bwl]/__raw_write[bwl]
is the right thing to do for on-chip peripherals. This patch converts
the drivers for the static memory controller, interrupt controller,
PIO controller and system manager to use __raw MMIO access.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement __raw_readsb and __raw_writesb. Export __raw_reads[bwl]
and __raw_writes[bwl] for use by modules.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While ioremap() will happily map a physical address through the
P2 (uncached) segment when appropriate, iounmap() doesn't know how
to handle those mappings.
This patch makes iounmap() do the right thing, i.e. nothing, for
such mappings.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Silence a few compile warnings which are basically harmless, but
easy to fix.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't generate listing by default, remove unused LIBGCC variable and
rename generated disassembly and listing files to vmlinux.{s,lst}.
Also make sure that files generated during the build are actually
removed with make clean.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Only look at per_cpu data for online cpus.
[PATCH] x86-64: Simplify the vector allocator.
* 'merge' of master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Make sure __cpu_preinit_ppc970 gets called on 970GX processors
[POWERPC] Fix CHRP platforms with only 8259
[POWERPC] IPIC: Fix spinlock recursion in set_irq_handler
[POWERPC] Fix the UCC rx/tx clock of QE
[POWERPC] cell: update defconfig
[POWERPC] spufs: fix another off-by-one bug in spufs_mbox_read
[POWERPC] spufs: fix signal2 file to report signal2
[POWERPC] Fix device_is_compatible() const warning
[POWERPC] Cell timebase bug workaround
[POWERPC] Support feature fixups in modules
[POWERPC] Support feature fixups in vdso's
[POWERPC] Support nested cpu feature sections
[POWERPC] Consolidate feature fixup code
[POWERPC] Fix hang in start_ldr if _end or _edata is unaligned
[POWERPC] Fix spelling errors in ucc_fast.c and ucc_slow.c
[POWERPC] Don't require execute perms on wrapper when building zImage.initrd
[POWERPC] Add 970GX cputable entry
[POWERPC] Fix build breakage with CONFIG_PPC32
[POWERPC] Fix compiler warning message on get_property call
[POWERPC] Simplify stolen time calculation
* when we have stop/sysrq/go, we get pt_regs of whatever executes
mc_work_proc(). Would be better to see what we had at the time of
interrupt that got us stop.
* stop/stop/stop..... will give stack overflow. Shouldn't allow stop
from mconsole_stop().
* stop/stop/go leaves us inside mconsole_stop() with
os_set_fd_block(req->originating_fd, 0);
reactivate_fd(req->originating_fd, MCONSOLE_IRQ);
just done by nested mconsole_stop(). Ditto.
* once we'd seen stop, there's a period when INTR commands are executed
out of order (as they should; we might have the things stuck badly
enough to never reach mconsole_stop(), but still not badly enough to
block mconsole_interrupt(); in that situation we _want_ things like
"cad" to be executed immediately). Once we enter monsole_stop(), all
INTR commands will be executed in order, mixed with PROC ones. We'd
better let user see that such change of behaviour has happened.
(Suggested by lennert).
* stack footprint of monsole_interrupt() is an atrocity; AFAICS we can
safely make struct mc_request req; static in function there.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On CHRP platforms with only a 8259 controller, we should set the
default IRQ host to the 8259 driver's one for the IRQ probing
fallbacks to work in case the IRQ tree is incorrect (like on
Pegasos for example). Without this fix, we get a bunch of WARN_ON's
during boot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This causes ipic_set_irq_type to set the handler directly rather
than call set_irq_handler, which causes spinlock recursion because
the lock is already held when ipic_set_irq_type is called.
I'm also not convinced that ipic_set_irq_type should be changing the
handler at all. There seem to be several controllers that don't and
several that do. Those that do would break what appears to be a common
usage of calling set_irq_chip_and_handler followed by set_irq_type, if a
non-standard handler were to be used. OTOH, irq_create_of_mapping()
doesn't set the handler, but only calls set_irq_type().
This patch gets things working in the spinlock-debugging-enabled case,
but I'm curious as to where the handler setting is ideally supposed to be
done. I don't see any documentation on set_irq_type() that clarifies
what the semantics are supposed to be.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MPC8323EMDS board ethernet interface with RMII uses the CLK16 divisor
for the rx and tx clock, but the ucc_set_qe_mux_rxtx() function doesn't
handle the CLK16 setting of the CMXUCR3 and CMXUCR4 registers. This
fixes it.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, spufs_mbox_read transfers more bytes than requested on a
read. If you ask for four bytes, you get eight. This fixes it to
transfer the largest multiple of four bytes that is less than or equal
to the number you asked for.
Note: one nasty property of this file in spufs is that you can only
read multiples of four bytes in the first place, since there is no way
to atomically put back a few bytes into the hardware register. Thus,
reading less than four bytes returns -EINVAL. Asking for more than
four returns the largest possible multiple of four.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the /signal2 file to actually give signal2 data.
Signed-off-by: Dwayne Grant Mcconnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a const'ification related warning with device_is_compatible()
and friends related to get_property() not properly having const
on it's input device node argument.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell CPU timebase has an erratum. When reading the entire 64 bits
of the timebase with one mftb instruction, there is a handful of cycles
window during which one might read a value with the low order 32 bits
already reset to 0x00000000 but the high order bits not yet incremeted
by one. This fixes it by reading the timebase again until the low order
32 bits is no longer 0. That might introduce occasional latencies if
hitting mftb just at the wrong time, but no more than 70ns on a cell
blade, and that was considered acceptable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for feature fixups in modules. This involves
adding support for R_PPC64_REL64 relocs to the 64 bits module loader.
It also modifies modpost.c to ignore the powerpc fixup sections (or it
would warn when used in .init.text).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the feature fixup mecanism so vdso's can be fixed up.
The main issue was that the construct:
.long label (or .llong on 64 bits)
will not work in the case of a shared library like the vdso. It will
generate an empty placeholder in the fixup table along with a reloc,
which is not something we can deal with in the vdso.
The idea here (thanks Alan Modra !) is to instead use something like:
1:
.long label - 1b
That is, the feature fixup tables no longer contain addresses of bits of
code to patch, but offsets of such code from the fixup table entry
itself. That is properly resolved by ld when building the .so's. I've
modified the fixup mecanism generically to use that method for the rest
of the kernel as well.
Another trick is that the 32 bits vDSO included in the 64 bits kernel
need to have a table in the 64 bits format. However, gas does not
support 32 bits code with a statement of the form:
.llong label - 1b (Or even just .llong label)
That is, it cannot emit the right fixup/relocation for the linker to use
to assign a 32 bits address to an .llong field. Thus, in the specific
case of the 32 bits vdso built as part of the 64 bits kernel, we are
using a modified macro that generates:
.long 0xffffffff
.llong label - 1b
Note that is assumes that the value is negative which is enforced by
the .lds (those offsets are always negative as the .text is always
before the fixup table and gas doesn't support emiting the reloc the
other way around).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are currently two versions of the functions for applying the
feature fixups, one for CPU features and one for firmware features. In
addition, they are both in assembly and with separate implementations
for 32 and 64 bits. identify_cpu() is also implemented in assembly and
separately for 32 and 64 bits.
This patch replaces them with a pair of C functions. The call sites are
slightly moved on ppc64 as well to be called from C instead of from
assembly, though it's a very small change, and thus shouldn't cause any
problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Quick fix for lack of memset(__bss_start, 0, _end-__bss_start) in
load_kernel(). If edata is unaligned, the loop will overwrite all
memory because r3 and r4 will never be equal.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When I generalized __assign_irq_vector I failed to pay attention
to what happens when you access a per cpu data structure for
a cpu that is not online. It is an undefined case making any
code that does it have undefined behavior as well.
The code still needs to be able to allocate a vector across cpus
that are not online to properly handle combinations like lowest
priority interrupt delivery and cpu_hotplug. Not that we can do
that today but the infrastructure shouldn't prevent it.
So this patch updates the places where we touch per cpu data
to only touch online cpus, it makes cpu vector allocation
an atomic operation with respect to cpu hotplug, and it updates
the cpu start code to properly initialize vector_irq so we
don't have inconsistencies.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
There is no reason to remember a per cpu position of which vector
to try. Keeping a global position is simpler and more likely to
result in a global vector allocation even if I don't need or require
it. For level triggered interrupts this means we are less likely to
acknowledge another cpus irq, and cause the level triggered irq to
harmlessly refire.
This simplification makes it easier to only access data structures
of online cpus, by having fewer special cases to deal with.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
HAS_TOUCHSCREEN_ADS7843_LH7 and HAS_TOUCHSCREEN_ADC_LH7 are referenced
but not defined in the LH7A40x configuration. Comment them out to
prevent them causing warnings.
Marc Singer said:
Feel free to remove the Kconfig lines. I'll add it back with
the rest of the config entries.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In ucc_fast.c and ucc_slow.c, "illegal" is twice spelled "illagal".
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Don't require that the wrapper script be executable when building
zImage.initrds. This has already been fixed for zImages.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
low_cpu_die is called from the CPU hotplug code on 32-bit powermacs,
but it is only defined if CONFIG_PM || CONFIG_CPU_FREQ_PMAC. This
changes the ifdef so it is defined for CONFIG_HOTPLUG_CPU on 32-bit
machines.
Signed-off-by: Srinivasa DS <srinivasa@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the warning message from the return value of function
get_property(), by making sure that the variable that receives the
value is marked as const.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
In calculating stolen time, we were trying to actually account for time
spent in the hypervisor. We don't really have enough information to do
that accurately, so don't try. Instead, we now calculate stolen time as
time that the current cpu thread is not actually dispatching instructions.
On chips without a PURR, we cannot do this, so stolen time will always
be zero. On chips with a PURR, this is merely the difference between
the elapsed PURR values and the elapsed TB values.
This gives us much more sane vaules from tools such as mpstat, even if
they are still a bit strange e.g. 2 busy threads on one cpu will both
appear to have 50% user time and 50% stolen time while 1 busy thread on
a cpu will look like 100% user on one of them and 100% idle on the other.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch increases the timeout for PCI split transactions on PHB1 on
the first Calgary to work around an issue with the aic94xx
adapter. Fixes kernel.org bugzilla #7180
(http://bugzilla.kernel.org/show_bug.cgi?id=7180)
Based on excellent debugging and a patch by Darrick J. Wong
<djwong@us.ibm.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
There was a typo in the C3 latency test to decide of the TSC
should be used or not. It used the C2 latency threshold, not the
C3 one. Fix that.
This should fix the time on various dual core laptops.
Signed-off-by: Andi Kleen <ak@suse.de>
The current implementation uses a sequence of a cacheflush and a copy.
This is racy in case of a multithreaded debuggee and renders GDB
virtually unusable.
Aside this fixes a performance hog rendering access to /proc/cmdline very
slow and resulting in a enough cache stalls for the 34K AP/SP programming
model to make the bare metal code on the non-Linux VPE miss RT deadlines.
The main part of this patch was originally written by Ralf Baechle;
Atushi Nemoto did the the debugging.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Revert timer routing behaviour back to 2.6.16 state
[PATCH] x86-64: Overlapping program headers in physical addr space fix
[PATCH] x86-64: Put more than one cpu in TARGET_CPUS
[PATCH] x86: Revert new unwind kernel stack termination
[PATCH] x86-64: Use irq_domain in ioapic_retrigger_irq
[PATCH] i386: Disable nmi watchdog on all ThinkPads
[PATCH] x86-64: Revert interrupt backlink changes
[PATCH] x86-64: Fix ENOSYS in system call tracing
[PATCH] i386: Fix fake return address
[PATCH] x86-64: x86_64 add NX mask for PTE entry
[PATCH] x86-64: Speed up dwarf2 unwinder
[PATCH] x86: Use -maccumulate-outgoing-args
[PATCH] x86-64: fix page align in e820 allocator
[PATCH] x86-64: Fix for arch/x86_64/pci/Makefile CFLAGS
[PATCH] i386: fix .cfi_signal_frame copy-n-paste error
[PATCH] x86-64: typo in __assign_irq_vector when updating pos for vector and offset
[PATCH] x86-64: x86_64 hot-add memory srat.c fix
[PATCH] i386: Update defconfig
[PATCH] x86-64: Update defconfig
Reintroduce NODES_SPAN_OTHER_NODES for powerpc
Revert "[PATCH] Remove SPAN_OTHER_NODES config definition"
This reverts commit f62859bb68.
Revert "[PATCH] mm: remove arch independent NODES_SPAN_OTHER_NODES"
This reverts commit a94b3ab7ea.
Also update the comments to indicate that this is still required
and where its used.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Kravetz <kravetz@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
By default route the 8254 over the 8259 and only disable
it on ATI boards where this causes double timer interrupts.
This should unbreak some Nvidia boards where the timer doesn't
seem to tick of it isn't enabled in the 8259. At least one
VIA board also seemed to have a little trouble with the disabled
8259.
For 2.6.20 we'll try both dynamically without black listing, but I think
for .19 this is the safer approach because it has been already well tested
in earlier kernels. This also makes the x86-64 behaviour the same
as i386.
Command line options can change all this of course.
Signed-off-by: Andi Kleen <ak@suse.de>
o A recent change to vmlinux.ld.S file broke kexec as now resulting vmlinux
program headers are overlapping in physical address space.
o Now all the vsyscall related sections are placed after data and after
that mostly init data sections are placed. To avoid physical overlap
among phdrs, there are three possible solutions.
- Place vsyscall sections also in data phdrs instead of user
- move vsyscal sections after init data in bss.
- create another phdrs say data.init and move all the sections
after vsyscall into this new phdr.
o This patch implements the third solution.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Magnus Damm <magnus@valinux.co.jp>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
TARGET_CPUS is the default irq routing poicy. It specifies which cpus the
kernel should aim an irq at. In physflat delivery mode we can route an irq to
a single cpu. But that doesn't mean our default policy should only be a
single cpu is allowed.
By allowing the irq routing code to select from multiple cpus this enables
systems with more irqs then we can service on a single processor to actually
work.
I just audited and tested the code and irqbalance doesn't care, and the
io_apic.c doesn't care if we have extra cpus in the mask. Everything will use
or assume we are using the lowest numbered cpu in the mask if we can't use
them all.
So this should result in no behavior changes except on systems that need it.
Thanks for YH Lu for spotting this problem in his testing.
Cc: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Jan convinced me that it was unnecessary because the assembly stubs do
this already on the stack.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Thanks to YH Lu for spotting this. It appears I missed this function when I
refactored allocate_irq_vector and introduced irq_domain, with the result that
all retriggered irqs would go to cpu 0 even if we were not prepared to receive
them there.
While reviewing YH's patch I also noticed that this function was missing
locking, and since I am now reading two values from two diffrent arrays that
looks like a race we might be able to hit in the real world.
Cc: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch:
- out of range system calls failing to return -ENOSYS under
system call tracing
[AK: split out from another patch by Jan as separate bugfix]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The fake return address was being set to __KERNEL_PDA, rather than 0.
Push it earlier while %eax still equals 0.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Andrew Morton <akpm@osdl.org>
This avoids some problems with gcc 4.x and earlier generating
invalid unwind information. In 4.1 the option is default
when unwind information is enabled.
And it seems to generate smaller code too, so it's probably
a good thing on its own. With gcc 4.0:
i386:
4683198 902112 480868 6066178 5c9002 vmlinux (before)
4449895 902112 480868 5832875 5900ab vmlinux (after)
x86-64:
4939761 1449584 648216 7037561 6b6279 vmlinux (before)
4854193 1449584 648216 6951993 6a1439 vmlinux (after)
On 4.1 it shouldn't make much difference because it is
default when unwind is enabled anyways.
Suggested by Michael Matz and Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Currently some code pieces assume that address returned by find_e820_area()
are page aligned. But looks like find_e820_area() had no such intention
and hence one might end up stomping over some of the data. One such case
is bootmem allocator initialization code stomped over bss.
This patch modified find_e820_area() to return page aligned address. This
might be little wasteful of memory but at the same time probably it is
easier to handle page aligned memory.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The arch/x86_64/pci directory was giving problems in a wierd cross-compile
environment. The exact cause is unknown, but the Makefile used CFLAGS
instead of EXTRA_CFLAGS. From what I can tell from
Documentation/kbuild/makefiles.txt, CFLAGS should not be used for this, it
should be EXTRA_CFLAGS. And it solves the cross-compile problem.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This was copied, pasted but not edited.
Cc: Andi Kleen <ak@muc.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch corrects the logic used in srat.c to figure out what
parsing what action to take when registering hot-add areas. Hot-add
areas should only be added to the node information for the
MEMORY_HOTPLUG_RESERVE case. When booting MEMORY_HOTPLUG_SPARSE hot-add
areas on everything but the last node are getting include in the node
data and during kernel boot the pages are setup then the kernel dies
when the pages are used. This patch fixes this issue.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix one more compile breakage caused by the post -rc1 IRQ changes.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Interrupts must be disabled during alternative instruction patching. On
systems with high timer IRQ rates, or when running in an emulator, timing
differences can result in random kernel panics because of running partially
patched instructions. This doesn't yet fix NMIs, which requires extricating
the patch code from the late bug checking and is logically separate (and also
less likely to cause problems).
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When enabling the mmapper driver I got warnings because this "const"
miscdevice structure is passed to function as non-const pointer; unlike struct
tty_operations, however, I verified that misc_{de,}register _do_ modify their
parameter, so this const attribute must be removed.
Since the purpose of the change was to guarantee that no lock was needed, add
a comment to prove this differently.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Silence useless warning about undefined symbol in Kconfig.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Freeing the stack is left uselessly to the caller of run_helper in some cases
- this is taken from run_helper_thread, but here it is useless, so no caller
needs it and the only place where this happens has a potential leak - in case
of error neither run_helper() nor xterm_open() call free_stack(). At this
point passing a pointer is not needed - the stack pointer should be passed
directly, but this change is not done here.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This should make sure that, for UML, host's configuration files are not
considered, which avoids various pains to the user. Our dependency are such
that the obtained Kconfig will be valid and will lead to successful
compilation - however they cannot prevent an user from disabling any boot
device, and if an option is not set in the read .config (say
/boot/config-XXX), with make menuconfig ARCH=um, it is not set. This always
disables UBD and all console I/O channels, which leads to non-working UML
kernels, so this bothers users - especially now, since it will happen on
almost every machine (/boot/config-`uname -r` exists almost on every machine).
It can be workarounded with make defconfig ARCH=um, but it is non-obvious and
can be avoided, so please _do_ merge this patch.
Given the existence of options, it could be interesting to implement
(additionally) "option required" - with it, Kconfig will refuse reading a
.config file (from wherever it comes) if the given option is not set. With
this, one could mark with it the option characteristic of the given
architecture (it was an old proposal of Roman Zippel, when I pointed out our
problem):
config UML
option required
default y
However this should be further discussed:
*) for x86, it must support constructs like:
==arch/i386/Kconfig==
config 64BIT
option required
default n
where Kconfig must require that CONFIG_64BIT is disabled or not present in the
read .config.
*) do we want to do such checks only for the starting defconfig or also for
.config? Which leads to:
*) I may want to port a x86_64 .config to x86 and viceversa, or even among more
different archs. Should that be allowed, and in which measure (the user may
force skipping the check for a .config or it is only given a warning by
default)?
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: <kbuild-devel@lists.sourceforge.net>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_MODE_TT does not work there, the UML_ prefixed version must be used -
this causes a link-time failure when CONFIG_MODE_TT is enabled (i.e. always
here, never by Jeff).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix coding conventions violations is arch/um/os-Linux/helper.c.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
user.h is too generic a header name. I've split out allocation routines from
it.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/um/sys-x86_64/ptrace.c:20:1: warning: "SC_SS" redefined
In file included from arch/um/include/sysdep/ptrace.h:18,
from include/asm/ptrace-generic.h:12,
from include/asm/ptrace.h:15,
from arch/um/sys-x86_64/ptrace.c:8:
arch/um/include/sysdep/sc.h:38:1: warning: this is the location of the previous definition
arch/um/sys-x86_64/ptrace.c: In function 'putreg':
arch/um/sys-x86_64/ptrace.c:63: warning: implicit declaration of function 'SC_FS_BASE'
arch/um/sys-x86_64/ptrace.c:63: error: invalid lvalue in unary '&'
arch/um/sys-x86_64/ptrace.c:63: warning: implicit declaration of function 'SC_GS_BASE'
arch/um/sys-x86_64/ptrace.c:63: error: invalid lvalue in unary '&'
arch/um/sys-x86_64/ptrace.c: In function 'getreg':
arch/um/sys-x86_64/ptrace.c:101: error: invalid lvalue in unary '&'
arch/um/sys-x86_64/ptrace.c:101: error: invalid lvalue in unary '&'
I'd have to say that the fix for this, for now, is this:
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the concept of "queue congestion" from "backing-dev congestion".
Congestion is a backing-dev concept, not a queue concept.
The blk_* congestion functions are retained, as wrappers around the core
backing-dev congestion functions.
This proper layering is needed so that NFS can cleanly use the congestion
functions, and so that CONFIG_BLOCK=n actually links.
Cc: "Thomas Maier" <balagi@justmail.de>
Cc: "Jens Axboe" <jens.axboe@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: David Howells <dhowells@redhat.com>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the INTC2 code contains a fixed IRQ table that it
iterates through to set the handler type, we move this in to
the CPU subtype setup code instead and allow for submitting
the table that way.
This drops the ST40 tables, as nothing has been happening
with those processors, while converting the only existing
users to use the new table directly (SH7760 and SH7780).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the existing prototype the following code:
const void __iomem *io = ioremap();
x = readb(io);
iounmap(io);
did result in a warning.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the current pnx8550-v2pci_defconfig CONFIG_SGI_IP22 has been selected.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the current pnx8550-jbs_defconfig CONFIG_SGI_IP22 has been selected.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_KALLSYMS=n case is obviously wrong, though it is harmless since
CONFIG_KALLSYMS is always enabled with CONFIG_STACKTRACE for now.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A sign extension bug did result in sys_personality being invoked with a
0xffffffffffffffffUL argument, so querying the current personality didn't
work.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This new routine doesn't lookup for symbol names. So we needn't
to pass any char buffers or pointer since we don't care about
names.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
handle_irq_name() and set_irq_chip_and_handler() disappeared,
update for desc->name and set_irq_chip_and_handler_name() use.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the recent change ripping out interrupt_table, explicit
padding of the table was missing, causing bad things to happen
when manually inserting handlers in to the table. This problem
particularly showed up in relation to do_fpu_state_restore()
which was inserted quite deeply in to the table and ended up
scribbling over a slab object.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now with the ide.h mess sorted out, most of these boards
don't need their own directory. Move the headers out, and
update the driver paths.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out some of the previous show_stack() implementation which
was mostly doing the show_trace() work without actually dumping any of
the stack contents. This now gets split in to two sections, where we
do the fetching of the stack pointer and subsequent stack dumping in
show_stack(), while moving the call trace in to show_trace().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation. Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively. Many people have come to expect this naming. Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations). I also have reports that various Sun and HP servers
have similar behavior.
Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also). 2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.
On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1. If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.
A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.
-[0000:00]-+-00.0 Intel Corporation 5000P Chipset Memory Controller Hub
+-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
+-1c.0-[0000:01-02]----00.0-[0000:02]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)
Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.
Solution:
The solution can come in multiple steps.
Suggested fix#1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels. It adds two new
command line options:
pci=bfsort
pci=nobfsort
to force the sort order, or not, as you wish. It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".
Suggested fix#2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in. I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first. It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.
Suggested fix#3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order. This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers). I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.
Feedback appreciated. Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.
You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm. I think
that's both safe and appropriate in this instance.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_fixup_video turns into generic code because there are many platforms need this fixup
for embedded VGA as well as x86. The Video BIOS integrates into System BIOS on a machine
has embedded VGA although embedded VGA generally don't have PCI ROM. As a result,
embedded VGA need the way that the sysfs rom points to the Video BIOS of System
RAM (0xC0000). PCI-to-PCI Bridge Architecture specification describes the condition whether
or not PCI ROM forwards VGA compatible memory address. fixup_video suits this specification.
Although the Video ROM generally implements in x86 code regardless of platform, some
application such as X Window System can run this code by dosemu86. Therefore,
pci_fixup_video should turn into generic code.
Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following compile error:
CC init/version.o
LD init/built-in.o
LD .tmp_vmlinux1
arch/s390/kernel/built-in.o(.text+0xdba4): In function `sys32_ipc':
: undefined reference to `compat_sys_semtimedop'
arch/s390/kernel/built-in.o(.text+0xdbee): In function `sys32_ipc':
: undefined reference to `compat_sys_semctl'
arch/s390/kernel/built-in.o(.text+0xdc08): In function `sys32_ipc':
: undefined reference to `compat_sys_msgsnd'
arch/s390/kernel/built-in.o(.text+0xdc30): In function `sys32_ipc':
: undefined reference to `compat_sys_msgrcv'
arch/s390/kernel/built-in.o(.text+0xdc58): In function `sys32_ipc':
: undefined reference to `compat_sys_msgctl'
arch/s390/kernel/built-in.o(.text+0xdc76): In function `sys32_ipc':
: undefined reference to `compat_sys_shmat'
arch/s390/kernel/built-in.o(.text+0xdcb0): In function `sys32_ipc':
: undefined reference to `compat_sys_shmctl'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch fixes a typo to make kernel compilable when floppy driver
for Sparc is build.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds profiling support to the sparc architecture. It is a
copy of the sparc64 implementation.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Hummingbird PCI controllers, we should create the root
PCI memory space resource as the full 4GB area, and then
allocate the IOMMU DMA translation window out of there.
The old code just assumed that the IOMMU DMA translation base
to the top of the 4GB area was unusable. This is not true on
many systems such as SB100 and SB150, where the IOMMU DMA
translation window sits at 0xc0000000->0xdfffffff.
So what would happen is that any device mapped by the firmware
at the top section 0xe0000000->0xffffffff would get remapped
by Linux somewhere else leading to all kinds of problems and
boot failures.
While we're here, report more cases of OBP resource assignment
conflicts. The only truly valid ones are ROM resource conflicts.
Signed-off-by: David S. Miller <davem@davemloft.net>
Unused, but still allow the '-s' boot option to be passed
down to init.
Based upon patches by Martin Habets.
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the number of "resched" interrupts that each cpu receives.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The current sn2_defconfig is obsolete, in particular the recent ATA
changes are a pain, so here's a patch to get things in sync ... at
least for a day or two :)
Update sn_defconfig to match current community kernel tree.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reformat to fit in 80 columns. Fix a couple typos. Remove
a couple unused labels.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Linux maps PAL instructions with an ITR, but uses a DTC for PAL data.
Section 11.10.2.1.3, "Making PAL Procedures Calls in Physical or Virtual
Mode," of the SDM (rev 2.2), says we must therefore make all PAL calls
with PSR.ic = 1 so that Linux can handle any TLB faults.
PAL_CALL_IC_OFF is currently unused, and as long as we use the ITR + DTC
strategy, we can't use it. So remove it. I also removed the code in
ia64_pal_call_static() that conditionally cleared PSR.ic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Allow pending IPIs to interrupt a timer interrupt that is looping
in the do_timer() "while" loop in timer_interrupt(). (Interrupts are
allowed at only 1 spot in the code).
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Missed one piece of ia64 fallout from the global IRQ patch
7d12e780e0
Perfmon interrupt handler needs to use get_irq_regs() too.
Acked-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Check for offline nodes in pci NUMA code
[POWERPC] Better check in show_instructions
[POWERPC] POWER6 has 6 PMCs
[POWERPC] Never panic when taking altivec exceptions from userspace
[POWERPC] Fix IO Window Updates on P2P bridges.
[POWERPC] Add Makefile entry for MPC832x_mds support
[POWERPC] Fix MPC8360EMDS PB board support
[POWERPC] ppc: Add missing calls to set_irq_regs
[POWERPC] Off-by-one in /arch/ppc/platforms/mpc8*
[POWERPC] Add DOS partition table support to mpc834x_itx_defconfig
[POWERPC] spufs: fix support for read/write on cntl
[POWERPC] Don't crash on cell with 2 BEs when !CONFIG_NUMA
Introduce desc->name and eliminate the handle_irq_name() hack. Add
set_irq_chip_and_handler_name() to set the flow type and name at once.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid possible PIT livelock issues seen on SMP systems (and reported by
Andi), by not allowing it as a clocksource on SMP boxes.
However, since the PIT may no longer be present, we have to properly handle
the cases where SMP systems have TSC skew and fall back from the TSC.
Since the PIT isn't there, it would "fall back" to the TSC again. So this
changes the jiffies rating to 1, and the TSC-bad rating value to 0.
Thus you will get the following behavior priority on i386 systems:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if UP]
jiffies
Rather then the current more complicated:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if cpus < 4]
tsc [if present & unstable]
jiffies
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During boot we bring up all memory and cpu nodes. Normally a PCI device
will be in one of these online nodes, however in some weird setups it
may not.
We have only seen this in the lab but we may as well check for the case
and fallback to -1 (all nodes).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of just checking that an address is in the right range, use the
provided __kernel_text_address() helper which covers both the kernel and
module text sections.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change ->num_pmcs to match the number of PMCs in POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At the moment we rely on a cpu feature bit or a firmware property to
detect altivec. If we dont have either of these and the cpu does in fact
support altivec we can cause a panic from userspace.
It seems safer to always send a signal if we manage to get an 0xf20
exception from userspace.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When update_bridge_base() updates the IO window on a PCI-to-PCI
bridge, it fails to zero the upper 16 bits of the base and limit
registers if the window size is less than 64K. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add missing entry in Makefile for MPC832x MDS support. It
also change white space to tab in MPC8360 entry.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MPC8360EMDS PB support is broken as some code was missing
in last submission. This patch adds missing code and makes
MPC8360EMDS PB support working.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the timer_interrupt we were not calling set_irq_regs() and if we are
profiling we will end up calling get_irq_regs(). This causes bad things to
happen.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A find -iname \*.[ch] | xargs grep "> ARRAY_SIZE(" revealed several
incorrect usages of ARRAY_SIZE in the mpc drivers. The last element in the
array is always ARRAY_SIZE()-1, this patch modifies the bounds checks
accordingly.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The default configuration file for the MPC8349E-mITX reference board,
mpc834x_itx_defconfig, did not include support for DOS partition table types.
This support is necessary because the hard drive that comes with the ITX
is formatted with this partition table type. Without this config option,
no partitions on the drive can be mounted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a memory leak introduced by "spufs: add support
for read/write oncntl", which was missing a call to simple_attr_close.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPU code will crash if CONFIG_NUMA is not set and SPUs are found on
a non-0 node. This workaround will ignore those SPEs and just print an
message in the kernel log.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I need this patch to get a UML kernel to compile. This is with the
kernel headers in FC6 which are automatically generated from the kernel
tree. Some headers are missing but those files don't need them. At
least it appears so since the resuling kernel works fine.
Tested on x86-64.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some ARM platforms were still broken as a result of the IRQ register
passing changes, mostly due to a missing linux/irq.h include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds correct sdram params for K4S281632B-1H and sets the jornada to use them by default.
Signed-off-by: Kristoffer Ericson
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Linux group at Stratus Technologies has come across an issue with SCI
routing under ACPI. We were bitten by this when we made an x86_64 platform
whose BIOS provides an Interrupt Source Override for the SCI itself.
Apparently the override has no effect for the System Control Interrupt, and
this appears to be because of the way the SCI is setup in the ACPI code.
It does not handle the case where busirq != gsi.
The code that sets up the SCI routing assumes that bus irq == global irq.
So there is simply no provision for telling it otherwise. The attached
patch provides this mechanism.
This patch provided by David Bulkow, was tested on an i386 platform, which
does not use the SCI override, and also on an x86_64 platform which does
use an override.
Signed-off-by: David Bulkow <david.bulkow@stratus.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel processors starting with the Core Duo support
support processor native C-state using the MWAIT instruction.
Refer: Intel Architecture Software Developer's Manual
http://www.intel.com/design/Pentium4/manuals/253668.htm
Platform firmware exports the support for Native C-state to OS using
ACPI _PDC and _CST methods.
Refer: Intel Processor Vendor-Specific ACPI: Interface Specification
http://www.intel.com/technology/iapc/acpi/downloads/302223.htm
With Processor Native C-state, we use 'MWAIT' instruction on the processor
to enter different C-states (C1, C2, C3). We won't use the special IO
ports to enter C-state and no SMM mode etc required to enter C-state.
Overall this will mean better C-state support.
One major advantage of using MWAIT for all C-states is, with this and
"treat interrupt as break event" feature of MWAIT, we can now get accurate
timing for the time spent in C1, C2, .. states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The new Atmel AT91SAM9261 and AT91SAM9260 processors use a different
internal watchdog peripheral. This watchdog driver is therefore
AT91RM9200-specific.
This patch renames at91_wdt.c to at91rm9200_wdt.c, and changes the name
of the configuration option.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of warning in the thermal throttling code about not checking
sysfs return values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apparently whoever converted voyager never actually checked that the
patch would compile ...
Remove as much of the pt_regs references as possible and move the
remaining ones into line with what's in x86 generic.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The implementation of genirq in x86 completely broke voyager (and
presumably visws). Since it's plugged into so much of the x86
infrastructure, you can't expect it to work unconverted.
This patch introduces a voyager IRQ handler type and switches voyager
to the genirq infrastructure.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Kernel build breaks with CONFIG_X86_VSMP. Probably due to some header
file cleanups in 2.6.19-rc1.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes my one line thinko where I was clearing
the vector_irq entries on the wrong cpus.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix these 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'core_kernel_text' (at offset 0x3e060) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'core_kernel_text' (at offset 0x3e064) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'core_kernel_text' (at offset 0x3e07c) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'core_kernel_text' (at offset 0x3e080) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'is_ksym_addr' (at offset 0x4b3a4) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'is_ksym_addr' (at offset 0x4b3a8) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'is_ksym_addr' (at offset 0x4b3b4) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'is_ksym_addr' (at offset 0x4b3e4) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0x4b640) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0x4b644) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'get_symbol_pos' (at offset 0x4b654) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'get_symbol_pos' (at offset 0x4b658) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0x4b68c) and 'kallsyms_lookup_size_offset'
The crux of the matter is that modpost only checks the relocatable
sections. i386 vmlinux has none, so modpost does no checking on it (it
does on the modules). However, sparc vmlinux has plenty of
relocatable sections because it is being built with 'ld -r' (to allow
for btfixup processing). So for sparc, modpost does do a lot of
checking. Sure enough, running modpost on arch/sparc/boot/image yields
no output (i.e. all is well).
modpost.c check_sec_ref() has:
/* We want to process only relocation sections and not .init */
if (sechdrs[i].sh_type == SHT_RELA) {
// check here
} else if (sechdrs[i].sh_type == SHT_REL) {
// check here
}
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:sunzilog_console_setup from .data between 'sunzilog_console' (at offset 0x8394) and 'devices_subsys'
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix these 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:__alloc_bootmem from .text between 'srmmu_nocache_init' (at offset 0x1a0f8) and 'srmmu_mmu_info'
WARNING: vmlinux - Section mismatch: reference to .init.text:__alloc_bootmem from .text between 'srmmu_nocache_init' (at offset 0x1a118) and 'srmmu_mmu_info'
WARNING: vmlinux - Section mismatch: reference to .init.text:srmmu_early_allocate_ptable_skeleton from .text between 'srmmu_nocache_init' (at offset 0x1a188) and 'srmmu_mmu_info'
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill off interrupt_table for all of the CPU subtypes, we now
default in to stepping in to do_IRQ() for _all_ IRQ exceptions
and counting the spurious ones, rather than simply flipping on
the ones we cared about. This and enabling the IRQ by default
automatically has already uncovered a couple of bugs and IRQs
that weren't being caught, as well as some that are being
generated far too often (SCI Tx Data Empty, for example).
The general rationale is to use a marker for interrupt exceptions,
test for it in the handle_exception() path, and skip out to
do_IRQ() if it's found. Everything else follows the same behaviour
of finding the cached EXPEVT value in r2/r2_bank, we just rip out
the INTEVT read from entry.S entirely (except for in the kGDB NMI
case, which is another matter).
Note that while this changes the do_IRQ() semantics regarding r4
handling, they were fundamentally broken anyways (relying entirely
on r2_bank for the cached code). With this, we do the INTEVT read
from do_IRQ() itself (in the CONFIG_CPU_HAS_INTEVT case), or fall
back on r4 for the muxed IRQ number, which should also be closer
to what SH-2 and SH-2A want anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that we've started accounting for spurious IRQs, change the
logic somewhat so that we have a better chance of catching them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Pass NULL not 0 for pointer value.
[MIPS] IP27: Make declaration of setup_replication_mask a proper prototype.
[MIPS] BigSur: More useful defconfig.
[MIPS] Cleanup definitions of speed_t and tcflag_t.
[MIPS] Fix compilation warnings in arch/mips/sibyte/bcm1480/smp.c
[MIPS] Optimize and cleanup get_saved_sp, set_saved_sp
[MIPS] <asm/irq.h> does not need pt_regs anymore.
[MIPS] Workaround for bug in gcc -EB / -EL options.
[MIPS] Fix timer setup for Jazz
Certain gcc versions upto gcc 4.1.1 (probably 4.2-subversion as of
2006-10-10 don't properly change the the predefined symbols if -EB / -EL
are used, so we kludge that here. A bug has been filed at
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=29413.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
taken exports to actual definitions of symbols being exported.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sun3_ksyms gone, m68k_ksyms trimmed down to exports of the assembler ones,
for sun3 added the missing exports of __ioremap() and iounmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix kernel-doc function name in usercopy.c.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the epoll_pwait system call, that extend the event wait mechanism
with the same logic ppoll and pselect do. The definition of epoll_pwait
is:
int epoll_pwait(int epfd, struct epoll_event *events, int maxevents,
int timeout, const sigset_t *sigmask, size_t sigsetsize);
The difference between the vanilla epoll_wait and epoll_pwait is that the
latter allows the caller to specify a signal mask to be set while waiting
for events. Hence epoll_pwait will wait until either one monitored event,
or an unmasked signal happen. If sigmask is NULL, the epoll_pwait system
call will act exactly like epoll_wait. For the POSIX definition of
pselect, information is available here:
http://www.opengroup.org/onlinepubs/009695399/functions/select.html
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that various memory splits are enabled, add a config option allowing the
user to compile UML for its need - HOST_2G_2G allowed to choose either 3G/1G
or 2G/2G, and enabling it reduced the usable virtual memory.
Detecting this at run time should be implemented in the future, but we must
make the stop-gap measure work well enough (this is valid in _many_ cases).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Deprecate TT mode in Kconfig so that users won't select it, update the
MODE_SKAS description (it was largely obsolete and misleadin) and btw describe
advantages for high memory usage with CONFIG_STATIC_LINK.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The export is together with the definition, in arch/x86_64/lib/csum-partial.c,
which is compiled in by arch/um/sys-x86_64/Makefile.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unify macros common to x86 and x86_64 kernel-offsets.h files.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable compilation of x86_64 crypto code;, and add the needed constant to make
the code compile again (that macro was added to i386 asm-offsets between
2.6.17 and 2.6.18, in 6c2bb98bc3).
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Declare UML partial support for LOCKDEP - however IRQFLAGS tracing requires
some coding which nobody did yet, so we cannot run full lockdep on UML. Grep
for CONFIG_TRACE_IRQFLAGS on i386 code to find their implementation.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On a 64bit Uml, if run under "setarch i386" (which a user did), uname()
currently returns the obtained i686 as machine - fix that. Btw, I'm quite
surprised that under setarch i386 a 64-bit binary can run.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes UML compile on any possible processor choice. The two problems were:
*) x86 code, when 386 is selected, checks at runtime boot_cpuflags, which we do
not have.
*) 3Dnow support for memcpy() et al. does not compile currently and fixing this
is not trivial, so simply disable it; with this change, if one selects MK7
UML compiles (while it did not).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If enable is moved by GCC in a register its value may not be preserved after
coming back there with longjmp(). So, mark it as volatile to prevent this;
this is suggested (it seems) in info gcc, when it talks about -Wuninitialized.
I re-read this and it seems to say something different, but I still believe
this may be needed.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make TT mode compile after the introduction of klibc's implementation of
setjmp.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was forgot in a previous patch so UML does not compile with TT mode
enabled.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct commit 5906e4171a - this makes more
sense: we turn pte_mkexec + pte_wrprotect to pte_mkread. However, due to a
bug in pte_mkread, it does the exact same thing as pte_mkwrite, so this patch
improves the code but does not change anything in practice. The pte_mkread
bug is fixed separately, as it may have big impact.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen pointed out that -mcmodel=kernel does not make sense for userspace
code and would stop everything from working, and pointed out the correct fix
for the original bug (not easy to do for me).
Reverts part of commit 06837504de.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
hw_interrupt_type is deprecated in favour of struct irq_chip.
[mingo@elte.hu: do x86_64 too]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arch-independent zone-sizing is using indices instead of symbolic names to
offset within an array related to zones (max_zone_pfns). The unintended
impact is that ZONE_DMA and ZONE_NORMAL is initialised on powerpc instead
of ZONE_DMA and ZONE_HIGHMEM when CONFIG_HIGHMEM is set. As a result, the
the machine fails to boot but will boot with CONFIG_HIGHMEM turned off.
The following patch properly initialises the max_zone_pfns[] array and uses
symbolic names instead of indices in each architecture using
arch-independent zone-sizing. Two users have successfully booted their
powerpcs with it (one an ibook G4). It has also been boot tested on x86,
x86_64, ppc64 and ia64. Please merge for 2.6.19-rc2.
Credit to Benjamin Herrenschmidt for identifying the bug and rolling the
first fix. Additional credit to Johannes Berg and Andreas Schwab for
reporting the problem and testing on powerpc.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the necessary changes to AVR32 required by the irq regs stuff.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The latest kernel 2.6.19-rc1 triggers a bug in the s390 specific stack
trace code when compiled with gcc 3.4.
This patch fixes the latest lock dependency validator code (2.6.19-rc1)
on s390 gcc 3.4. The variable sp was fixed to r15 (which is the stack
pointer in the s390 abi) and assigned new values to r15. Therefore,
gcc 3.4 assigns a new value to r15 and does not restore it on exit (r15
is supposed to be call save) - the kernel stack is broken. Avoid trouble
by not assigning any new value to sp (r15).
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the last few places where a pointer to pt_regs gets passed.
Also make sure we call set_irq_regs() before irq_enter() and after
irq_exit(). This doesn't fix anything but makes sure s390 looks the
same like all other architectures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On the old "powersurge" SMP powermacs, the second CPU is started up
by sending it an IPI, which has the side effect of stopping the
timebase clock (so the secondary CPU's timebase can be synchronized
with the primary's). The routine that did this used udelay, which
will hang forever when the timebase is stopped, since udelay now spins
until the timebase reaches a certain value.
The end result is that the kernel would hang when bringing up the
second CPU. This fixes it by using a simple loop which just does a
fixed number of iterations to generate the delay. These old systems
were all clocked at around 200 MHz or so, so a fixed number of
iterations is acceptable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the Maple defconfig to 4 CPUs (along with current defaults)
to support the "tigerwood" 970MP evaluation board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The IDE driver will pick up the PCI IRQ for both channels on Maple
despite the fact that it's in legacy mode. This works around it by
"hiding" the PCI IRQ of the AMD8111 IDE controller when it's configured
in legacy mode on the Maple platform, thus causing the driver to call
pci_get_legacy_ide_irq() which will return the correct interrupts for
both channels.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Maple support code was missing code for U4/CPC945 PCIe. This adds
it, enabling it to work on tigerwood boards, and possibly also js21
using SLOF. Also disable an obsolete firmware workaround.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change CONFIG_PPC_CELL to CONFIG_PPC_IBM_CELL_BLADE in the powerpc boot
makefile.
CONFIG_PPC_CELL is used to build the generic cell processor support, and
is not an indication of platform.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My CROSS_COMPILE is "ccache /opt/compilers/blah", which confuses
the boot wrapper script. Quote CROSS_COMPILE and CROSS32_COMPILE
so they can safely contain spaces.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix these 2.6.19-rc1 build warnings:
CC arch/sparc/kernel/prom.o
arch/sparc/kernel/prom.c: In function `of_set_property':
arch/sparc/kernel/prom.c:246: warning: passing arg 2 of `prom_setprop' discards qualifiers from pointer target type
arch/sparc/kernel/prom.c: In function `build_one_prop':
arch/sparc/kernel/prom.c:446: warning: unused variable `len'
arch/sparc/kernel/prom.c:480: warning: ignoring return value of `prom_getproperty', declared with attribute warn_unused_result
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
They have to be unique system-wide, so use
"NAME@NODE" as the string pattern of the non-root
nodes.
Thanks to Andrew Morton for fixing the error value
checking in bus_add_device() which made this problem
finally noticable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure cpu_has_fpu (which uses smp_processor_id()) is used only in
atomic context.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX49 CPUs have a SYNC instruction so that CONFIG_CPU_HAS_WB is no
longer needed.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make sure that RA on top of interrupt stack is an address of ret_from_irq,
so that dump_stack etc. can trace info interrupted context.
Also this patch fixes except_vec_vi_handler and __smtc_ipi_vector which
seems broken.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only revisions < 4.0 don't have a functional wait instruction.
From Thomas Koeller (Thomas.Koeller@baslerweb.com).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- SERIAL167 is no longer broken
- Removed some unused variables from the driver to fix compiler warnings
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove unused arch/m68k/apollo/dma.c, which was obsoleted by the move to the
generic DMA API.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Misc Atari fixes:
- initialize correct number of atari irqs
- silence vbl interrupt until it's used by atafb
- use mdelay() to read clock if necessary
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Due to code bugs or misbehaving hardware it is possible that we can
receive an interrupt that we have not mapped into a linux irq. Calling
BUG when that happens is very rude, and if the problem is mild enough
prevents anything else from getting done.
So instead of calling BUG just scream loudly about the problem and
continue running. We don't have enough knowledge to know which
interrupt triggered this behavior so we don't acknowledge it. This will
likely prevent a recurrence of the problem by jamming up the works with
an unacknowledged interrupt.
If the interrupt was something important it is quite possible that
nothing productive will happen past this point. But it is now at least
possible to keep working if the kernel can survive without the interrupt
we dropped on the floor.
Solutions like irqpoll should generally make dropped irqs non-fatal.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>