dma_request_channel provides an exclusive channel, so we no longer need to
pass slave data through dmaengine.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the defconfigs for ATNGW100 and ATSTK100[236] the DMA Test driver is
compiled as a module. This means systems built with *_defconfig +
CONFIG_MODULES=n are unusable as the 3 dma test channels monopolise the
CPU.
I 'spose Haavard uses this module a lot but IMO it isn't really
something needed on all eval boards by default.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
As noted by Akinobu Mita in patch b1fceac2b9,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory. Thus a NULL test or memset after calls to these
functions is unnecessary.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
at32_add_device_mci() will refuse to add the mci device if the data
parameter is NULL. Fix up the favr-32 and hammerhead boards so that this
doesn't happen.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Alex Raimondi <mailinglist@miromico.ch>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Needed to use the atmel-mci driver in an architecture
independant maner.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel. It offers versatile peripherals, such as ethernet, usb
device, usb host etc.
The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).
Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.
This patch does include the basic support for the fpga device driver,
but not the device driver itself.
Signed-off-by: Alex Raimondi <mailinglist@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
at32_reserve_pin now takes an u32 bitmask rather than a single pin.
This allows to reserve multiple pins at once.
Remove (undocumented) SDCS (pin PE26) from reservation in board
setup code.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch removes a call to the deprecated function
at32_add_system_devices().
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
(I did not compile or test it, please let me know, or help fixing
it, if something is wrong with the conversion)
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Thanks,
Kay
From: Kay Sievers <kay.sievers@vrfy.org>
Subject: avr: struct device - replace bus_id with dev_name(), dev_set_name()
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Like fls, but can't be handed 0 and returns the bit number.
(I broke this arch in linux-next by using __fls in generic code).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The favr-32 board code still refers to the old asm/arch header files
which were moved to mach/ some time ago.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Enable JFFS2 write buffer support so that the kernel can access a root
filesystem in NAND flash.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch will remove the section .note.gnu.build-id added in binutils
2.18 from the vmlinux.bin binary. Not removing this section results in a
huge multiple gigabyte binary and likewize large uImage.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Make USART initialization conform to Section 24.6.1 in the AT32AP7000 manual,
i.e. "To prevent the TXD line from falling when the USART is disabled, the use
of an internal pull up is mandatory."
Signed-off-by: Anders Blomdell <anders.blomdell@control.lth.se>
[haavard.skinnemoen@atmel.com: enable pullup on RX as well]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add essential system devices, including GPIO controllers, automatically
at core_initcall time. This ensures that the devices are there when the
PIO driver gets initialized at postcore_initcall, fixing a bug exposed
by commit d6634db8fe "avr32: Use
platform_driver_probe for pio platform driver".
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The loops_per_jiffy variable isn't updated when cpufreq changes the CPU
frequency. This could cause udelay() and friends to produce wrong
delays.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Bug was introduced with the new at32_select_periph function.
Signed-off-by: Alex Raimondi <mailinglist@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series introduces a cgroup subsystem that utilizes the swsusp
freezer to freeze a group of tasks. It's immediately useful for batch job
management scripts. It should also be useful in the future for
implementing container checkpoint/restart.
The freezer subsystem in the container filesystem defines a cgroup file
named freezer.state. Reading freezer.state will return the current state
of the cgroup. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This patch:
The first step in making the refrigerator() available to all
architectures, even for those without power management.
The purpose of such a change is to be able to use the refrigerator() in a
new control group subsystem which will implement a control group freezer.
[akpm@linux-foundation.org: fix sparc]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SET_PERSONALITY macro is always called with a second argument of 0.
Remove the ibcs argument and the various tests to set the PER_SVR4
personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As policy->governor is already set to CPUFREQ_DEFAULT_GOVERNOR in the
(always built-in) cpufreq core, we do not need to set it in the drivers.
This fixes the sparc64 allmodconfig build failure.
Also, remove a totally useles setting of ->policy in cpufreq-pxa3xx.c.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Please consider the following patch which adds support for a new AVR32
based board.
The board is closely based on Atmel's NGW100 reference board, but has an
extra 8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The MIMC200 board uses the SPD output pin from the Ethernet MACs for
other purposes.
One of these is as a board-reset, so I've had to #define off the SPD
output pin declaration.
This is probably not the best way of achieving this, but works in the
current framework.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds support for the Favr-32 board made by EarthLCD.
This kit, which is also called ezLCD-101, has a 10.4" touch screen LCD panel,
16 MB 32-bit SDRAM, 8 MB parallel flash, Ethernet, audio out, USB device,
SD-card slot, USART and various other connectors for cennecting stuff to SPI,
I2C, GPIO, etc.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch lets the user enable support for EVKLCD100 and EVKLCD101
(refered to by EVKLCD10X). By enabling EVKLCD10X support the LCD
controller and AC97 controller platform devices are added.
The user can also choose between the EVKLCD100 (QVGA display) and the
EVKLCD101 (VGA display), this is added to automagically select the
correct panel timing and resolution parameters.
Enabling support for EVKLCD10X addon board will cripple the MCI platform
device a bit since they share two GPIO lines (detect and write-protect).
These two lines are disabled when EVKLCD10X is enabled.
The default configurations are based upon ATNGW100, but with added AC97C
and LCDC driver. Virtual terminal is also enabled by default for
EVKLCD10X boards.
Verified on hardware with a NGW100 + EVKLCD100/101.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The contents of the ATSTK1000 Kconfig file itself is completely
conditional, so including it conditionally makes no sense and only adds
clutter.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Fix a few instances of board code breakage introduced by the atmel-mci
platform interface changes.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
at32_select_periph() now takes an u32 bitmask rather than a single pin.
This allows to set multiple pins at once.
Signed-off-by: Alex Raimondi <mailinglist@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Include <linux/pm.h> to see the declaration of pm_power_off, and remove
unneeded NULL initializer.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This adds support for DMA transfers through the generic DMA engine
framework with the DMA slave extensions.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 7.5 MiB/s on fast cards with debugging disabled.
Unfortunately, the driver has been known to lock up from time to time
with DMA enabled, so DMA support is currently optional and marked
EXPERIMENTAL. However, I didn't see any problems while testing 13
different cards (MMC, SD and SDHC of different brands and sizes), so I
suspect the "Initialize BLKR before sending data transfer command" fix
that was posted earlier fixed this as well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Atmel MCI controller can drive multiple cards through separate sets
of pins, but only one at a time. This patch adds support for
multiplexing access to the controller so that multiple card slots can be
used as if they were hooked up to separate mmc controllers.
The atmel-mci driver registers each slot as a separate mmc_host. Both
access the same common controller state, but they also have some state
on their own for card detection/write protect handling, and separate
shadows of the MR and SDCR registers.
When one of the slots receives a request from the mmc core, the common
controller state is checked. If it's idle, the request is submitted
immediately. If not, the request is added to a queue. When a request is
done, the queue is checked and if there is a queued request, it is
submitted before the completion callback is called.
This patch also includes a few cleanups and fixes, including a locking
overhaul. I had to change the locking extensively in any case, so I
might as well try to get it right. The driver no longer takes any
irq-safe locks, which may or may not improve the overall system
performance.
This patch also adds a bit of documentation of the internal data
structures.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add the necessary platform infrastructure to support multiple mmc/sdcard
slots all at once through a single controller. Currently, the driver
will use the first valid slot it finds and stick with that, but later
patches will add support for switching between several slots on the fly.
Extend the platform data structure with per-slot information: MMC/SDcard
bus width and card detect/write protect pins. This will affect the pin
muxing as well as the capabilities announced to the mmc core.
Note that board code is now required to supply a mci_platform_data
struct to at32_add_device_mci().
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This replaces the at32_clock_list array with a linked list.
Clocks can now be registered (added) to the list.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The probe function of the pdc platform driver lives in the init section
and so a pdc device that is created after the init section is discarded
probably results in an oops. Even if this cannot happen, using
platform_driver_probe is cleaner. (If this can happen and should be
supported the probe function must live in the devinit section instead.)
Signed-off-by: Uwe Kleine-König <ukleinek@strlen.de>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The probe function of the pio platform driver lives in the init section
and so a pio device that is created after the init section is discarded
probably results in an oops. Even if this cannot happen, using
platform_driver_probe is cleaner. (If this can happen and should be
supported the probe function must live in the devinit section instead.)
Signed-off-by: Uwe Kleine-König <ukleinek@strlen.de>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Currently, setting up the portmux is completely one-shot: Once a pin is
muxed, the portmux driver will complain loudly and refuse to do anything
if you try to set up the same pin again.
Sometimes, it may be necessary to change the configuration of a pin
after it has been set up initially. This patch adds a way to undo the
previous configuration, allowing the pin to be reconfigured.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The NGW100 board has jumper J15 (near the reset button) which
is unused. This patch exports it through the GPIO sysfs support
(as /sys/class/gpio/gpio62/value) so that it's easily queried
by boot scripts or whatever might want to know if the jumper
has been installed (value = 0) or not (value = 1, "default").
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
[haavard.skinnemoen@atmel.com: add missing include]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This replaces the pin_config param with an u64 pin_mask in
at32_add_device_lcdc, allowing a board-maintainer to indivually select
specific lcdc pins.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Julien May <jmay@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds backtracing capability to oprofile profiling in kernel
and user mode on AVR32. This is done by going through the frames on the
stack and adding oprofile traces for all return addresses. The code
being profiled has to be compiled with frame pointers to make this work.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
While updating the rcu code, I noticed that do_nmi() for AVR32 is odd:
There is an nmi_enter() call without an nmi_exit().
This can't be correct, it breaks rcu (at least the preempt version) and
lockdep.
[haavard.skinnemoen@atmel.com: fixed another case that returned directly]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On AVR32, all parameters beyond the 5th are passed on the stack. System
calls don't use the stack -- they borrow a callee-saved register
instead. This means that syscalls that take 6 parameters must be called
through a stub that pushes the last parameter on the stack.
This patch adds a stub for sync_file_range syscall on AVR32
architecture. Tested with uClibc snapshot.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch implements the generic_find_next_le_bit bit function for AVR32
architecture. This is used by EXT4 file system.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The #ifdef surrounding the code adding the mmc controller had a typo,
causing it to be compiled even when mmc was supposed to be disabled.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch also includes the required removal of (unused) inclusion of
<asm/a.out.h> <linux/a.out.h>'s in the arch/ code for these
architectures.
[dwmw2: updated for 2.6.27-rc]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The value stored into the SDRAMC LPR register should be the current
value of the register with the Self-refresh value set in the lower bit
field.
The bug involved only the Self-refresh value being written to the
register, thus over writing any low-power ram settings.
Signed-off-by: Humphrey Bucknell <hbucknell@saitek.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
When using the Java Extension Module hardware, a Java stack underflow or
overflow trap may cause the system to enter an infinite exception loop.
Although there's no kernel support for the Java hardware yet, we need to
be able to recover from this situation and keep the system running.
This patch adds code to detect and fixup this situation in the critical
exception handler and terminate the faulting process. We may have to
rethink how to handle this more gracefully when the necessary kernel
support for hardware-accelerated Java is added.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Doing this in combination with "atmel_spi: fix hang due to missed
interrupt" appears to eliminate the overruns I'm seeing when using
JFFS2-on-DataFlash as /usr filesystem on the ATNGW100.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Enable power management, DMA and MMC on all boards except ATSTK1004, and
add defconfig for the new ATSTK1006 board with NAND flash, UBI and UBIFS
enabled as well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Introduce a few helper functions for HMATRIX configuration and clean up
the register definitions. Also add definitions for the HMATRIX master
and slave IDs on the AT32AP700x chips.
Also make the definitions in hmatrix.h available to board code by moving
it to <mach/hmatrix.h>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Hardcoded MMIO base addresses are used a few places throughout the
platform code. Move these into the chip-specific header file so that
adding support for new chips becomes a bit easier.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This file includes the appropriate chip-specific header with MMIO, IRQ
and GPIO definitions used by the platform code. It may also be used to
provide inline GPIO accessors for drivers that are willing to sacrifice
portability for faster bitbanging.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Since all users have been converted over to use <mach/foo.h>, there's no
need for the arch-at32ap directory and associated symlink anymore.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Update all avr32-specific files to use the new platform-specific header
locations. Drivers shared with ARM are left alone for now.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add arch/avr32/mach-*/include to include search path and copy all the
files from include/asm/arch there. The old files will be removed once
ARM does the same change and all common drivers are converted.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Minor cleanups for the MMC/SD support on avr32:
- Make at32_add_device_mci() properly initialize "missing"
platform data ... so boards like STK1002 won't try GPIO 0.
- Switch over to gpio_is_valid() instead of testing for only
one designated value.
- Provide STK1002 platform data for the unlikely case that
switches are set so first Ethernet controller isn't in use.
(That's the only way to get card detect and writeprotect
switch sensing on the STK1000.)
And get rid of one "unused variable" warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* git://git.infradead.org/mtd-2.6: (57 commits)
[MTD] [NAND] subpage read feature as a way to increase performance.
CPUFREQ: S3C24XX NAND driver frequency scaling support.
[MTD][NAND] au1550nd: remove unused variable
[MTD] jedec_probe: Fix SST 16-bit chip detection
[MTD][MTDPART] Fix a division by zero bug
[MTD][MTDPART] Cleanup and document the erase region handling
[MTD][MTDPART] Handle most checkpatch findings
[MTD][MTDPART] Seperate main loop from per-partition code in add_mtd_partition
[MTD] physmap: resume already suspended chips on failure to suspend
[MTD] physmap: Fix suspend/resume/shutdown bugs.
[MTD] [NOR] Fix -ETIMEO errors in CFI driver
[MTD] [NAND] fsl_elbc_nand: fix section mismatch with CONFIG_MTD_OF_PARTS=y
[JFFS2] Use .unlocked_ioctl
[MTD] Fix const assignment in the MTD command line partitioning driver
[MTD] [NOR] gen_probe: No debug message when debugging is disabled
[MTD] [NAND] remove __PPC__ hardcoded address from DiskOnChip drivers
[MTD] [MAPS] Remove the bast-flash driver.
[MTD] [NAND] fsl_elbc_nand: ecclayout cleanups
[MTD] [NAND] fsl_elbc_nand: implement support for flash-based BBT
[MTD] [NAND] fsl_elbc_nand: fix OOB workability for large page NAND chips
...
Remove arch-specific show_mem() in favor of the generic version.
This also removes the following redundant information display:
- free pages, printed by show_free_areas()
- pages in slabs, printed by show_free_areas()
- pages in swapcache, printed by show_swap_cache_info()
where show_mem() calls show_free_areas(), which calls
show_swap_cache_info().
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch allows the avr32_comparator interrupt to be shared.
This is necessary as the avr32 oprofile driver shares the irq group 0
with the timer.
To make OProfile actually work on AVR32, a small patch for oprofiled is
also needed (posted to the oprofile mailing list).
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
[haavard.skinnemoen@atmel.com: set IRQF_SHARED unconditionally]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
arch/mips/kernel/stacktrace.c: Heiko can't type
kthread: reduce stack pressure in create_kthread and kthreadd
fix core/stacktrace changes on avr32, mips, sh
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of this field need a PFN instead of a physical address,
so replace node_boot_start with node_min_pfn.
[Lee.Schermerhorn@hp.com: fix spurious BUG_ON() in mark_bootmem()]
Signed-off-by: Johannes Weiner <hannes@saeureba.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
free_area_init_node() gets passed in the node id as well as the node
descriptor. This is redundant as the function can trivially get the node
descriptor itself by means of NODE_DATA() and the node's id.
I checked all the users and NODE_DATA() seems to be usable everywhere
from where this function is called.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flag platforms as HAVE_CLK (or not) in Kconfig, based on whether they
support <linux/clk.h> calls, so that otherwise portable drivers which need
those calls can list that dependency.
Something like this is a prerequisite for merging the musb_hdrc driver,
currently used on platforms including Davinci, OMAP2430, OMAP3xx ... and
the discrete TUSB6010 chip, which doesn't have a natural platform
dependency. (Used with OMAP 2420 in current Nokia N8x0 tablets.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds platform data to the AC97C platform device. This will
let the board add a GPIO line which is connected to the external codecs
reset line.
The platform data, ac97c_platform_data, must also contain the DMA
controller ID, RX channel ID and TX channel ID.
Tested with Wolfson WM9712 and AP7000.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
I/OAT: I/OAT version 3.0 support
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT: Add watchdog/reset functionality to ioatdma
iop_adma: cleanup iop_chan_xor_slot_count
iop_adma: document how to calculate the minimum descriptor pool size
iop_adma: directly reclaim descriptors on allocation failure
async_tx: make async_tx_test_ack a boolean routine
async_tx: remove depend_tx from async_tx_sync_epilog
async_tx: export async_tx_quiesce
async_tx: fix handling of the "out of descriptor" condition in async_xor
async_tx: ensure the xor destination buffer remains dma-mapped
async_tx: list_for_each_entry_rcu() cleanup
dmaengine: Driver for the Synopsys DesignWare DMA controller
dmaengine: Add slave DMA interface
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
dmaengine: Add dma_client parameter to device_alloc_chan_resources
dmatest: Simple DMA memcpy test client
dmaengine: DMA engine driver for Marvell XOR engine
iop-adma: fix platform driver hotplug/coldplug
dmaengine: track the number of clients using a channel
...
Fixed up conflict in drivers/dca/dca-sysfs.c manually
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fixes this type of problem:
CC arch/s390/kernel/stacktrace.o
arch/s390/kernel/stacktrace.c:84: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:84: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:84: warning: parameter names (without types) in function declaration
arch/s390/kernel/stacktrace.c:97: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:97: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:97: warning: parameter names (without types) in function declaration
caused by "stacktrace: export save_stack_trace[_tsk]"
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch does a few small cleanups around the atmel mci platform code
and in the atmel-mci driver. The platform changes simply removes an
unused variable, uses the fact that by the end we always have some form
of platform data and notes that GPIO_PIN_NONE != 0. This last point
could cause the incorrect attempt to twice reserve pin PA0.
While we've got the hood up, add linux/err.h to the atmel-mci.c include
list. It needs it and generally pulls it by voodoo but I did once
stumble across a config which don't build.
This is against Linus' latest git.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This is a driver for the MMC controller on the AP7000 chips from
Atmel. It should in theory work on AT91 systems too with some
tweaking, but since the DMA interface is quite different, it's not
entirely clear if it's worth merging this with the at91_mci driver.
This driver has been around for a while in BSPs and kernel sources
provided by Atmel, but this particular version uses the generic DMA
Engine framework (with the slave extensions) instead of an
avr32-only DMA controller framework.
This driver can also use PIO transfers when no DMA channels are
available, and for transfers where using DMA may be difficult or
impractical for some reason (e.g. the DMA setup overhead is usually
not worth it for very short transfers, and badly aligned buffers or
lengths are difficult to handle.)
Currently, the driver only support PIO transfers. DMA support has been
split out to a separate patch to hopefully make it easier to review.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 3.5 MiB/s on fast cards with debugging disabled.
The driver has also been tested using the mmc_test module on the same
cards. All tests except 7, 9, 15 and 17 succeed. The first two are
unsupported by all the cards I have, so I don't know if the driver
handles this correctly. The last two fail because the hardware flags a
Data CRC Error instead of a Data Timeout error. I'm not sure how to deal
with that.
Documentation for this controller can be found in many data sheets from
Atmel, including the AT32AP7000 data sheet which can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.
This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.
The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.
Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:
http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf
The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since v4:
* Use client_count instead of dma_chan_is_in_use()
* Add missing include
* Unmap buffers unless client told us not to
Changes since v3:
* Update to latest DMA engine and DMA slave APIs
* Embed the hw descriptor into the sw descriptor
* Clean up and update MODULE_DESCRIPTION, copyright date, etc.
Changes since v2:
* Dequeue all pending transfers in terminate_all()
* Rename dw_dmac.h -> dw_dmac_regs.h
* Define and use controller-specific dma_slave data
* Fix up a few outdated comments
* Define hardware registers as structs (doesn't generate better
code, unfortunately, but it looks nicer.)
* Get number of channels from platform_data instead of hardcoding it
based on CONFIG_WHATEVER_CPU.
* Give slave clients exclusive access to the channel
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement Standby support. In this mode, we'll suspend all drivers,
put the SDRAM in self-refresh mode and switch off the HSB bus
("frozen" mode.)
Implement Suspend-to-mem support. In this mode, we suspend all
drivers, put the SDRAM into self-refresh mode and switch off all
internal clocks except the 32 kHz oscillator ("stop" mode.)
The lowest-level suspend code runs from a small portion of SRAM
allocated at startup time. This gets rid of a small potential race
with the SDRAM where we might try to enter self-refresh mode in the
middle of an icache burst. We also relocate all interrupt and
exception handlers to SRAM during the small window when we enter and
exit the low-power modes.
We don't need to do any special tricks to start and stop the PLL. The
main clock is automatically gated by hardware until the PLL is stable.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This makes the intc show up in sysfs (probably not very useful), and
allows us to easily add suspend/resume support later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The SDRAM controller needs a clock in order to respond to our
commands, and suspend doesn't work very well without the SDRAM in
self-refresh mode.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Use a quicklist to allocate process PGDs. This is expected to be
slightly faster since we need to copy entries from swapper_pg_dir,
which can stay around for pages on the PGD quick list.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Expand the per-process PGDs so that they cover the kernel virtual
memory area as well. This simplifies the TLB miss handler fastpath
since it doesn't have to check for kernel addresses anymore.
If a TLB miss happens on a kernel address and a second-level page
table can't be found, we check swapper_pg_dir and copy the PGD entry
into the user PGD if it can be found there.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Instead of storing physical addresses along with page flags in the
PGD, store virtual addresses and use NULL to indicate a not present
second-level page table. A non-page-aligned page table indicates a bad
PMD.
This simplifies the TLB miss handler since it no longer has to check
the Present bit and no longer has to convert the PGD entry from
physical to virtual address. Instead, it has to check for a NULL
entry, which is slightly cheaper than either.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This and the following patches aim to optimize the code dealing with
page tables and TLB operations. Each patch reduces the time it takes
to gzip a 16 MB file slightly, but I expect things like fork() and
mmap() will improve somewhat more.
This patch deals with the low-level TLB operations:
* Remove unused _TLBEHI_I define
* Use gcc builtins instead of inline assembly
* Remove a few unnecessary pipeline flushes and nops
* Introduce NR_TLB_ENTRIES define and use it instead of hardcoding it
to 32 a few places throughout the code.
* Use sysreg bitops instead of hardcoded shifts and masks
* Make a few needlessly global functions static
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The only thing left in at32ap.c is some PDC stuff. Rename the file to
reflect what it actually does.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Combine at32_clock_init() and at32_portmux_init() into
setup_platform() and remove setup_platform() from at32ap.c. No
functional change since all setup_platform() ever did was call those
two functions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Kill the special exception handler sections .tlbx.ex.text,
.tlbr.ex.text, tlbw.ex.text and .scall.text. Use .org instead to place
the handlers at the required offsets from EVBA.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The name "mck" causes a conflict on AT91. Call it "pwm_clk" instead.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This is a minor tweak to the at32ap700x pin configuration for the SPI
input pin (MISO), enabling the on-chip weak pullup (typical 190K) to
(a) ensure a fixed data value for missing or input-only slaves;
(b) prevent power waste associated with inputs floating near VDDIO/2.
Atmel's boards have no external pullup or pulldown on these pins, so
it's unlikely other boards would address these issues with external
pulldowns. Were there trouble, board-specific code could turn off
the relevant pullup(s).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Basic I2C initialization for the NGW100 board:
- Provide empty i2c device table. Daughtercards may add devices,
and the ATtiny24 could do stuff too.
- Set up EXTINT(3) so the ATtiny24 can interrupt the AP7000.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds the PS/2 interface (PSIF) to the device code, split into
two platform devices, one for each port.
The function for adding the PSIF platform device is also added to the
board header file.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch lets the board code choose which pin out to use for the LCD
interface.
On AT32AP7000 the LCDC is wired to two sets of pins, which lets the user
choose between dual ethernet and 32-bit EBI. For the ATNGW100 board it
is vital to have the choice to select the alternative pinout since this
pinout is routed to the external headers.
Update ATSTK1002 and ATSTK1004 to use the new interface.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On the odd chance some code uses a pin as a GPIO IRQ without calling
gpio_request() or gpio_direction_input(), the debug dump should still
show its pin status.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
__raw_readsb() should always use byte accesses, never halfword accesses,
to I/O memory.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
A signal handler should be able to change the signal stack used for the
next signal by altering the ucontext_t passed as a parameter to the
handler. This does not currently work on avr32 since it doesn't update
the in-kernel signal context from the ucontext_t upon signal handler
return.
Fix it by adding a call to do_sigaltstack() from sys_rt_sigreturn(),
bringing it in line with most other architectures.
Signed-off-by: Martin Koegler <mkoegler@auto.tuwien.ac.at>
[haavard.skinnemoen@atmel.com: changed patch description]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On our custom board we have other oscillator rates than on atngw100 and
atstk100x.
Currently these rates are hardcoded in arch/avr32/mach-at32ap/at32ap700x.c.
This patch moves them into board specific code.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Fixes one of two ext4 build problems:
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The ATSTK1006 is basically an upgraded version of ATSTK1002 with
128 MiB SDRAM and 256 MiB NAND flash on board.
Otherwise, the board is very similar to the ATSTK1002, so it uses the
same board support file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This function initializes and adds a platform_device for a NAND flash
interface on SMC chip select 3.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The board init code, typically running from postcore_initcall, may
need to set up SMC timings. We have to make sure the SMC driver is
ready before this happens.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Move the AP7 cpufreq init to late_initcall() so that we don't try to
bring up cpufreq until the governor is ready. x86 also uses
late_initcall() for this.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Just provide reasonable defaults for the new stuff. Tickless and
hrtimers are turned on for all boards except ATSTK1004.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This replaces the duplicated arch-specific versions of "sys_pipe()" with
one unified implementation. This removes almost 250 lines of duplicated
code.
It's marked __weak, so that *if* an architecture wants to override the
default implementation it can do so by simply having its own replacement
version, since many architectures use alternate calling conventions for
the 'pipe()' system call for legacy reasons (ie traditional UNIX
implementations often return the two file descriptors in registers)
I still haven't changed the cris version even though Linus says the BKL
isn't needed. The arch maintainer can easily do it if there are really
no obstacles.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create() to make sure that ->proc_fops be setup before gluing PDE to
main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the user specified a fixed framebuffer address on the command line, it may
have been initialized already with a splash image or something, so we
shouldn't clear it.
Therefore, we should only initialize the framebuffer if we allocated it
ourselves. This patch also updates the AVR32 setup code to clear the
framebuffer if it allocated it itself, i.e. the user didn't provide a fixed
address or the reservation failed.
I've updated the at91 platform code as well so that it initializes the
framebuffer if it is located in SRAM, but I haven't tested that it actually
works.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds in the indirect call to pm_power_off(), as is done in
other architectures (e.g. ARM).
Tested on NGW100, with custom board with GPIO control over main DC
power.
Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch is a take two of adding full functionality to PLL1 on
AT32AP7000. This allows board-specific code and drivers to configure
and enable PLL1. This is useful when precise control over the
frequency of e.g. a genclock is needed and requested by users for the
ABDAC device.
The patch is based upon previous patches from both Haavard Skinnemoen
and David Brownell.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This combines three patches from David Brownell:
* avr32: tclib support
* avr32: simplify clocksources
* avr32: Turn count/compare into a oneshot clockevent device
Register both TC blocks (instead of just the first one) so that
the AT32/AT91 tclib code will pick them up (instead of just the
avr32-only PIT-style clocksource).
Rename the first one and its resources appropriately.
More cleanups to the cycle counter clocksource code
- Disable all the weak symbol magic; remove the AVR32-only TCB-based
clocksource code (source and header).
- Mark the __init code properly.
- Don't forget to report IRQF_TIMER.
- Make the system work properly with this clocksource, by preventing
use of the CPU "idle" sleep state in the idle loop when it's used.
Package the avr32 count/compare timekeeping support as a oneshot
clockevent device, so it supports NO_HZ and high res timers.
This means it also supports plugging in other clockevent devices
and clocksources.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Create a new file, pm-at32ap700x.S, in mach-at32ap and move the CPU
idle sleep code there. Make it possible to disable the sleep code.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Move the only thing that was actually implemented and used in
asm/intc.h, intc_get_pending(), into asm/irq.h and delete asm/intc.h
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Start cleaning up the AVR32 clocksource mess, starting with the cycle
counter clocksource: remove unneeded pseudo-RTC (just inline that
call to mktime) and associated build warning, and unused sysdev.
Add comment about the problem using the cycle counter register,
and adjust the clocksource rating accordingly. Later patches can
make this usable again (by disabling use of the idle state and
providing a proper clocksource without the weak binding hacks)
and move towards TCB-based clockevent support (including high
resolution timers) that's shared between AT91 and AVR32.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
New-style I2C drivers require that motherboard-mounted I2C devices are
registered with the I2C core, typically at arch_initcall time. This
can be done nice and neat by passing the struct i2c_board_info[]
through at32_add_device_twi just like we do for the SPI board info.
While we've got the hood up, remove a duplicate declaration of
at32_add_device_twi() in board.h.
[hskinnemoen@atmel.com: add missing i2c_board_info forward-declaration]
Signed-Off-By: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
There's a libata based PATA driver for avr32, but no support for
drivers/ide/ on avr32.
This patch fixes the following compile error:
<-- snip -->
...
CC [M] drivers/ide/ide-cd.o
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/ide-cd.c:37:
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/ide.h:209:21: error: asm/ide.h: No such file or directory
make[3]: *** [drivers/ide/ide-cd.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The atmel_usba_udc driver is being used by several platforms and arches
(avr32 and at91 ATM), and each platform may have different endpoint
settings.
The patch below moves the endpoint declarations into the platform
data and make the necessary adjustments for AVR32 (improved by
Haavard Skinnemoen <hskinnemoen@atmel.com>).
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
add_reserved_region() tries to keep the resource list sorted, so when
looking for a place to insert the new resource, it may break out
before the last entry.
When this happens, the list is broken in two because the sibling field
of the new entry doesn't point to the next resource. Fix it by
updating the new resource's sibling field appropriately.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Don't include the BUG trap handling code when CONFIG_BUG is not set.
This fixes allnoconfig.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Iff the parent has TIF_DEBUG set, _and_ clone_flags includes
CLONE_PTRACE we should set the TIF_DEBUG flag for the child and
increment the ocd refcount. Otherwise, the TIF_DEBUG flag must be
unset.
Currently, the child inherits TIF_DEBUG from the parent before
copy_thread is called, so TIF_DEBUG may be already be set before we
determine whether the child is supposed to inherit debugging
capabilities from the parent or not. This means that ocd_enable()
won't increment the refcount, because TIF_DEBUG is already set, and
that TIF_DEBUG will be set for processes that aren't being debugged.
This leads to a refcounting asymmetry, which may show up as
------------[ cut here ]------------
Badness at arch/avr32/kernel/ocd.c:73
PC is at ocd_disable+0x34/0x60
LR is at put_lock_stats+0xa/0x20
as reported by David Brownell. Happens when strace'ing a process that
forks a new child process, e.g. "strace mount -tjffs2 mtd1 /mnt", and
subsequently killing the child process (e.g. "umount /mnt".)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This fixes a hang on boot with nohz enabled. nohz is not actually
supported in mainline yet, but patches that add support for it are
currently under review.
When nohz is compiled out, the functions are no-ops, so this patch
results in no functional change, but it arguably makes the code more
correct.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
CONFIG_BOARD_ATSTK1002_SW2_CUSTOM should be
CONFIG_BOARD_ATSTK100X_SW2_CUSTOM.
Spotted by Robert P. J. Day.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The per-task page tables only cover the first 2GiB of the address
space. For kernel addresses, we need to do the lookup in init's page
tables.
This is a temporary workaround until we modify the per-task page
tables to cover the whole 4GiB address space.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
PWM device setup, and a simple PWM driver exposing a programming interface
giving access to each channel's full capabilities. Note that this doesn't
support starting several channels in synch.
[hskinnemoen@atmel.com: allocate platform device dynamically]
[hskinnemoen@atmel.com: Kconfig fix]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes simple attributes might need to return an error, e.g. for
acquiring a mutex interruptibly. In fact we have that situation in
spufs already which is the original user of the simple attributes. This
patch merged the temporarily forked attributes in spufs back into the
main ones and allows to return errors.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stefano.brivio@polimi.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.
This patch:
Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past. This is to avoid conflicts.
Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- All implementations can be __devinit
- The function prototypes were in asm/timex.h but they all must be the same,
so create a single declaration in linux/timex.h.
- uninline the sparc64 version to match the other architectures
- Don't bother #defining ARCH_HAS_READ_CURRENT_TIMER to a particular value.
[ezk@cs.sunysb.edu: fix build]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach AVR32 to use the "GPIO Library" when exposing its GPIOs, so that signals
on external chips (like GPIO expanders) can easily be used.
This mostly reorganizes some existing logic, with two minor changes in
behavior:
- The PSR registers are used instead of the previous "gpio_mask" values,
matching AT91 behavior and removing some duplication between that role
and that of "pinmux_mask".
- NR_IRQs grew to acommodate a bank of external GPIOs. Eventually this
number should probably become a board-specific config option.
There's a debugfs dump of status for the built-in GPIOs, showing which pins
have deglitching, pullups, or open drain drive enabled, as well as the ID
string used when requesting each IRQ.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AVR32 still includes Kconfig.instrumentation, so it won't build after
this...
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config KPROBES_SUPPORT
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
- Use HAVE_KPROBES
- Use a select
- Yet another update :
Moving to HAVE_* now.
- Update ARM for kprobes support.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config ARCH_SUPPORTS_KPROBES
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
Changelog :
- Moving to HAVE_*.
- Add AVR32 oprofile.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] extint: Set initial irq type to low level
[AVR32] extint: change set_irq_type() handling
[AVR32] NMI debugging
[AVR32] constify function pointer tables
[AVR32] ATNGW100: Update defconfig
[AVR32] ATSTK1002: Update defconfig
[AVR32] Kconfig: Choose daughterboard instead of CPU
[AVR32] Add support for ATSTK1003 and ATSTK1004
[AVR32] Clean up external DAC setup code
[AVR32] ATSTK1000: Move gpio-leds setup to setup.c
[AVR32] Add support for AT32AP7001 and AT32AP7002
[AVR32] Provide more CPU information in /proc/cpuinfo and dmesg
[AVR32] Oprofile support
[AVR32] Include instrumentation menu
Disable VGA text console for AVR32 architecture
[AVR32] Enable debugging only when needed
ptrace: Call arch_ptrace_attach() when request=PTRACE_TRACEME
[AVR32] Remove redundant try_to_freeze() call from do_signal()
[AVR32] Drop GFP_COMP for DMA memory allocations
David Brownell pointed out a mismatch in the avr32 extint code:
> I noticed a small glitch that's not fixed by this patch: the
> initial type is falling edge, but IRQ_TYPE_NONE is mapped to
> IRQ_TYPE_LEVEL_LOW. Potentially surprising.
Fix it by setting the initial type (and handler) to low level,
matching the meaning of IRQ_TYPE_NONE.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Update the AVR32 EIC code to use the new __set_irq_handler_unlocked()
call, getting rid of one more instance of this widespread problem.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Change the NMI handler to use the die notifier chain to signal anyone
who cares. Add a simple "nmi debugger" which hooks into this chain and
that may dump registers, task state, etc. when it happens.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Remove the CPU selection menu and instead let it be selected by the
board or daughterboard option. Add daughterboard selection for
ATSTK1000 (this was previously determined based on CPU type.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
ATSTK1003 and ATSTK1004 are CPU daughterboards for ATSTK1000 featuring
the AT32AP7001 and AT32AP7002 CPUs, respectively.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Reduce the ridiculous amount of #ifdef clutter in atstk1002.c a bit by
moving all the extdac stuff into its own function and providing an
empty stub for the case when it isn't wanted.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
There may be other boards than STK1002 that want to use the leds on
STK1000. Move it to stk1000 common code to make it easier to reuse.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
These are derivatives of the AT32AP7000 chip, which means that most of
the code stays the same. Rename a few files, functions, definitions
and config symbols to reflect that they apply to all AP700x chips, and
exclude some platform devices from chips where they aren't present.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add the following fields to /proc/cpuinfo:
* chip type and revision (from the JTAG chip id)
* cpu MHz (from clk_get_rate())
* features (from the CONFIG0 register)
Also rename "cpu family" to "cpu arch" and "cpu type" to "cpu core" to
remove some ambiguity.
Show chip type and revision at bootup, and clarify that the other
kinds of IDs that we're already printing are for the cpu core and
architecture. Rename "AP7000" to "AP7" since that's the name of the
core.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds the necessary architecture code to run oprofile on AVR32
using the performance counters documented by the AVR32 Architecture
Manual.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Philippe Elie <phil.el@wanadoo.fr>
Keep track of processes being debugged (including the kernel itself)
and turn the OCD system on and off as appropriate. Since enabling
debugging turns off some optimizations in the CPU core, this fixes the
issue that enabling KProbes support or simply running a program under
gdbserver will reduce system performance significantly until the next
reboot.
The CPU performance will still be reduced for all processes while a
process is being debugged, but this is a lot better than reducing the
performance forever.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
get_signal_to_deliver() will call try_to_freeze(), so there's no point
in do_signal() doing it as well.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
dma_alloc_coherent wants to split pages after allocation in order to
reduce the memory footprint. This does not work well with GFP_COMP
pages, so drop this flag before allocation.
This patch was forward-ported from BSP 2.0
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not like it really matters at this point since the system is
dying anyway, but handle_critical pushes too few registers on the
stack so the register dump, which makes the register dump look a bit
strange. This patch fixes it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current implementation of copy_to_user_page() gives "vaddr" to the
cache instruction when trying to sync the icache with the dcache. If
vaddr does not exist in the TLB, the CPU will silently abort the
operation, which may result in the caches staying out of sync.
To fix this, pass the "dst" parameter to flush_icache_range() instead
-- we know this is valid because we just wrote to it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current debug trap handling code does a number of things that are
illegal according to the AVR32 Architecture manual. Most importantly,
it may try to schedule from Debug Mode, thus clearing the D bit, which
can lead to "undefined behaviour".
It seems like this works in most cases, but several people have
observed somewhat unstable behaviour when debugging programs,
including soft lockups. So there's definitely something which is not
right with the existing code.
The new code will never schedule from Debug mode, it will always exit
Debug mode with a "retd" instruction, and if something not running in
Debug mode needs to do something debug-related (like doing a single
step), it will enter debug mode through a "breakpoint" instruction.
The monitor code will then return directly to user space, bypassing
its own saved registers if necessary (since we don't actually care
about the trapped context, only the one that came before.)
This adds three instructions to the common exception handling code,
including one branch. It does not touch super-hot paths like the TLB
miss handler.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Generate a new set of OCD register definitions in asm/ocd.h and rename
__mfdr() and __mtdr() to ocd_read() and ocd_write() respectively.
The bitfield definitions are a lot more complete now, and they are
entirely based on bit numbers, not masks. This is because OCD
registers are frequently accessed from assembly code, where bit
numbers are a lot more useful (can be fed directly to sbr, bfins,
etc.)
Bitfields that consist of more than one bit have two definitions:
_START, which indicates the number of the first bit, and _SIZE, which
indicates the number of bits. These directly correspond to the
parameters taken by the bfextu, bfexts and bfins instructions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The 'H' bit is bit 29, while the 'R' bit doesn't exist. Luckily, we
don't actually use any of the bits in question.
Also update show_regs() to show the Debug Mask and Debug state bits.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
