Allow users to set boxed devices offline. After setting them
offline, the device state will still be boxed.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a ccw device appears not operational, inform the associated
device driver and act according to the response: if the driver
wants to keep the device, put it into the disconnected state.
If not, or if there is no driver or if the device is not online,
unregister it. This approach is consistent with no-path event
handling.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When there is no path left to a ccw device, inform the associated
device driver and act according to the response: if the driver
wants to keep the device, put it into the disconnected state.
If not, or if there is no driver or if the device is not online,
unregister it.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is a memory leak in /proc/cio_ignore. The iterator is allocated
in cio_ignore_proc_seq_start, but never freed in
cio_ignore_proc_seq_stop, because we cannot use the iterator
that was passed by seqfile. The seqfile interface passes the last
seen iterator to the stop function and not the first one. Since our
next function will return NULL at the end, the iter passed to
cio_ignore_proc_seq_stop is NULL. The original iter has leaked.
The solution is to use seq_open_private.
Found with kmemleak:
unreferenced object 0x1c720580 (size 32):
comm "head", pid 973, jiffies 4294958302
hex dump (first 32 bytes):
00 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<0000000000203154>] kmem_cache_alloc+0x190/0x19c
[<00000000003fb462>] cio_ignore_proc_seq_start+0x5e/0x128
[<0000000000231018>] seq_read+0xc8/0x4bc
[<0000000000273954>] proc_reg_read+0xa8/0xf4
[<000000000020e3d8>] vfs_read+0xac/0x1a4
[<000000000020e5c6>] SyS_read+0x52/0xa8
[<000000000011836e>] sysc_noemu+0x10/0x16
[<0000004690b7936c>] 0x4690b7936c
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move dev_set_name to when we know that the device will actually be
registered in order to avoid a memory leak if the allocated memory
for the channel path has to be freed.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this build failure:
drivers/s390/built-in.o: In function `raw3270_pm_unfreeze':
(.text+0x3ac04): undefined reference to `ccw_device_force_console'
with:
CONFIG_TN3270=y
CONFIG_TN3270_CONSOLE=n
CONFIG_TN3215_CONSOLE=n
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* remove asm/atomic.h inclusion from linux/utsname.h --
not needed after kref conversion
* remove linux/utsname.h inclusion from files which do not need it
NOTE: it looks like fs/binfmt_elf.c do not need utsname.h, however
due to some personality stuff it _is_ needed -- cowardly leave ELF-related
headers and files alone.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (22 commits)
[S390] Update default configuration.
[S390] hibernate: Do real CPU swap at resume time
[S390] dasd: tolerate devices that have no feature codes
[S390] zcrypt: Do not add/remove devices in s/r callbacks
[S390] hibernate: make sure pfn_is_nosave handles lowcore pages
[S390] smp: introduce LC_ORDER and simplify lowcore handling
[S390] ptrace: use common code for simple peek/poke operations
[S390] fix disabled_wait inline assembly clobber list
[S390] Change kernel_page_present coding style.
[S390] hibernation: reset system after resume
[S390] hibernation: fix guest page hinting related crash
[S390] Get rid of init_module/delete_module compat functions.
[S390] Convert sys_execve to function with parameters.
[S390] Convert sys_clone to function with parameters.
[S390] qdio: change state of all primed input buffers
[S390] qdio: reduce per device debug messages
[S390] cio: introduce consistent subchannel scanning
[S390] cio: idset use actual number of ssids
[S390] cio: dont kfree vmalloced memory
[S390] cio: introduce css_settle
...
The DASD device driver reads the feature codes of a device during
device initialization. These codes are later used to determine the
availability of advanced features like PAV or High Performance FICON.
Some very old devices do not support the command to read feature
codes and the initialization routine fails.
As the feature codes are not necessary for basic DASD operations, we
can support such devices by just ignoring missing feature codes.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Devices are no longer removed or added in the suspend and resume
callbacks. Instead they are marked unregistered in suspend. In the
resume callback the ap_scan_bus method is scheduled. The bus scan
function will remove the old device and add new ones. This way all
the device handling will be done in only one function. Additionaly
the case where the domain might change during suspend/resume is
caught. In that case the devices qid needs to re-calculated in
order of having it found by the scan method.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If input buffers stay in primed state qdio may not receive further interrupts
for the input queue depending on the firmware. That can cause a connection
hang on OSA cards.
Change the state of all primed input buffers that are not acknowledged to
not initialized.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Even if turned off the debug message overhead is measurable in the hot path.
Reduce the number of debug message calls in do_QDIO and qdio_kick_handler.
Also use hex numbers to save space in the debug entries.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Previously, there were multiple subchannel scanning mechanisms
which could potentially conflict with each other. Fix this problem
by moving blacklist and ccw driver triggered scanning to the
existing evaluation method.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The functions idset_sch_new and for_each_subchannel_staged
use different values for the number of subchannel sets. Make
it consistent by changing idset_sch_new to also use the actual
number of subchannel sets.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't use kfree to free memory allocated by vmalloc.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the css_driver callback settle which can be implemented
by a subchannel driver to wait for the subchannel type specific
asynchronous work to finish.
In channel_subsystem_init_sync we call that for each subchannel
driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use css_eval_scheduled to determine if all scheduled subchannel
evaluation is finished. Wait for this value to be 0 in the
channel subsystem init function.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define initialization sequence of css and ccw bus init calls by merging
them into a single init call. Also introduce channel_subsystem_init_sync
to wait for the initialization of devices to finish.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (209 commits)
[SCSI] fix oops during scsi scanning
[SCSI] libsrp: fix memory leak in srp_ring_free()
[SCSI] libiscsi, bnx2i: make bound ep check common
[SCSI] libiscsi: add completion function for drivers that do not need pdu processing
[SCSI] scsi_dh_rdac: changes for rdac debug logging
[SCSI] scsi_dh_rdac: changes to collect the rdac debug information during the initialization
[SCSI] scsi_dh_rdac: move the init code from rdac_activate to rdac_bus_attach
[SCSI] sg: fix oops in the error path in sg_build_indirect()
[SCSI] mptsas : Bump version to 3.04.12
[SCSI] mptsas : FW event thread and scsi mid layer deadlock in SYNCHRONIZE CACHE command
[SCSI] mptsas : Send DID_NO_CONNECT for pending IOs of removed device
[SCSI] mptsas : PAE Kernel more than 4 GB kernel panic
[SCSI] mptsas : NULL pointer on big endian systems causing Expander not to tear off
[SCSI] mptsas : Sanity check for phyinfo is added
[SCSI] scsi_dh_rdac: Add support for Sun StorageTek ST2500, ST2510 and ST2530
[SCSI] pmcraid: PMC-Sierra MaxRAID driver to support 6Gb/s SAS RAID controller
[SCSI] qla2xxx: Update version number to 8.03.01-k6.
[SCSI] qla2xxx: Properly delete rports attached to a vport.
[SCSI] qla2xxx: Correct various NPIV issues.
[SCSI] qla2xxx: Correct qla2x00_eh_wait_on_command() to wait correctly.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
For messages from the tape core that is shared between the 3590 and 34xx
tape disciplines, we want to have the "tape" prefix instead of "tape_3590"
or "tape_34xx". In order to fix this, we now use the pr_xxx printk macros.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge cpuid.h header file into cpu.h.
While at it convert from typedef to struct declaration and also
convert cio code to use proper lowcore structure instead of casts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently, when a tape device is set online and no cartridge is loaded, we
get the messages "The tape cartridge has been successfully unloaded" and
"Determining the size of the recorded area". These messages are not correct.
To fix this, we now print the "cartridge loaded/unloaded" messages only,
when the load/unload event really occurs. In addition to that, the message
"Determining the size of the recorded area" is only printed, if a cartridge
is loaded.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use a console_initcall() to initialize the s390 virtio console and
clean up s390 console initialization in setup.c.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If dev_set_name fails during scanning the AP bus, the reserved memory
has to be freed.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently in the suspend process checksums for the XPRAM partitions are
created and stored. During the resume process it is checked,
if the checksums are still the same. If this is not the case, a kernel panic
is triggered. Unfortunately this prevents XPRAM from beeing used as suspend
device, because in this case after the checksum has been created, the
memory image is written to XPRAM and therefore the contents of the suspend
partition is changed. In order to allow XPRAM to be used as suspend device,
this patch removes the checksum validation.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vmur class is allocated after the CCW driver is registered
and it is destroyed before the CCW driver is unregistered.
This is not the correct sequence, because the vmur class can be used
via driver core callbacks that are triggered during the CCW driver
deregistration. For Example:
1. vmur device is online
2. vmur module is unloaded
This leads to the following function call stack:
<4> [<0000000000387286>] device_destroy+0x36/0x5c
<4> [<000003e000209714>] ur_set_offline_force+0x9c/0x10c [vmur]
<4> [<000003e00020a928>] ur_remove+0x64/0xbc [vmur]
<4> [<00000000003e4d2e>] ccw_device_remove+0x42/0x1ac
<4> [<000000000038a1aa>] __device_release_driver+0x9a/0xe4
<4> [<000000000038a2da>] driver_detach+0xe6/0xec
<4> [<0000000000388ee4>] bus_remove_driver+0xc0/0x108
<4> [<000003e00020ad5a>] ur_exit+0x52/0x84 [vmur]
In device_destroy() the vmur class is used. Since it is already freed,
this can lead to a kernel panic.
To fix the problem, the vmur class has to be allocated before the CCW
driver is registered and destroyed after the CCW driver has ben unregistered.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With CONFIG_DEBUG_OBJECTS_TIMERS=y "chccwdev --online" for a tape device
will fail with message "ODEBUG: object is on stack, but not annotated".
We now use init_timer_on_stack.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't use kfree directly after device registration started.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch fixes message naming so that generic dasd messages do not
contain the device discipline. For this purpose the dev_ makros are
replaced by pr_ makros for generic dasd messages.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A DASD device that is not ready or online has no defined disk layout,
so all requests that arrive in such a state need to be returned as
failed.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We used the init_name to set the console ccw_device's name early
at the boot stage. This patch moves the name setting (for all ccw
devices) to the point where we actually register the device. At this
time we can do dynamic allocations and therefore use dev_set_name.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We use a test_and_clear_bit to prevent a device from being
unregistered twice. Unfortunately in this cases the "final"
put_device (from device_initialize) was issued more than once,
resulting in an use after free error. Fix this by moving this
put_device to ccw_device_unregister.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We used the init_name to set the console subchannels name early
at the boot stage. With the patch cio: fix memleak in subchannel validation
we moved the name setting to the point where we actually register the
console subchannel. At this time we can do dynamic allocations and therefore
use dev_set_name.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When scanning for new subchannels we have a code path where we allocate
memory for a struct subchannel, set the device name (which is dynamically
allocated now) and do a check if the underlying device is blacklisted - if
so we free the subchannel structure.
Since we have not set up refcounting at this stage, the device name's memory
is lost. Fix this by moving the dev_set_name after the blacklist test.
Note: With this patch the init_name for the console subchannel becomes
virtually obsolete.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When using s390dbf with "%s" in sprintf format strings the string itself
is not copied to the dbf buffer.
Since in this case only pointers are stored in the s390dbf, we should
not use dev_name - which is bound to the lifetime of the device.
Reading this entry from s390dbf after the device was released will cause
an use after free error.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The number of qdio debugfs entries was limited. Remove this limit
and group the queue files in a per device directory.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When unit checks trigger sensing the device state is set to W4SENSE
until sense completion; then the device state is set back to
ONLINE. If a unit check occurs while set online or set offline
requests are processed then it might happen that the device's
temporary W4SENSE state causes these functions to terminate,
leaving the device in an inconsistent state when the state is set
back to ONLINE later on so that the device cannot be set online or
offline any longer.
To solve this, set online/offline and related rollback or error
routines are processed only if the device is in a final or
DISCONNECTED state.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure to always hold an extra device reference for scheduling a
subchannel deregistration, by moving the get_device to
ccw_device_schedule_sch_unregister. This fixes an use after free
error in ccw_device_call_sch_unregister where put_device was called
on an already freed device structure.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With commit c38f960809 polling was
stopped for the queue even if new data is available.
Return immediately after scheduling the queue tasklet if the queue
is not done.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
