This patch adds definitions of non-IBM specific v6 extended log
definitions to rtas.h.
Signed-off-by: Tseng-Hui (Frank) Lin <tsenglin@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Due to a collision between NO_CONTEXT->MMU_NO_CONTEXT change and
Anton's patch.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a multiple message send syscall and is the send
version of the existing recvmmsg syscall. This is heavily
based on the patch by Arnaldo that added recvmmsg.
I wrote a microbenchmark to test the performance gains of using
this new syscall:
http://ozlabs.org/~anton/junkcode/sendmmsg_test.c
The test was run on a ppc64 box with a 10 Gbit network card. The
benchmark can send both UDP and RAW ethernet packets.
64B UDP
batch pkts/sec
1 804570
2 872800 (+ 8 %)
4 916556 (+14 %)
8 939712 (+17 %)
16 952688 (+18 %)
32 956448 (+19 %)
64 964800 (+20 %)
64B raw socket
batch pkts/sec
1 1201449
2 1350028 (+12 %)
4 1461416 (+22 %)
8 1513080 (+26 %)
16 1541216 (+28 %)
32 1553440 (+29 %)
64 1557888 (+30 %)
We see a 20% improvement in throughput on UDP send and 30%
on raw socket send.
[ Add sparc syscall entries. -DaveM ]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fundamental reset is an optional reset type supported only by PCIe adapters.
Handle the unexpected case where a non-PCIe device has requested a
fundamental reset. Try hot-reset as a fallback to handle this case.
Signed-off-by: Richard A Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For multifunction adapters with a PCI bridge or switch as the device
at the Partitionable Endpoint(PE), if one or more devices below PE
sets dev->needs_freset, that value will be set for the PE device.
In other words, if any device below PE requires a fundamental reset
the PE will request a fundamental reset.
Signed-off-by: Richard A Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds support for page coalescing, which is a feature on IBM Power servers
which allows for coalescing identical pages between logical partitions.
Hint text pages as coalesce candidates, since they are the most likely
pages to be able to be coalesced between partitions. This patch also
exports some page coalescing statistics available from firmware via
lparcfg.
[BenH: Moved a couple of things around to fix compile problems]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit b987812b3f left
crash_kexec_wait_realmode() undefined for UP.
Commit 7c7a81b53e defined it for UP but
left it undefined for 32-bit SMP.
Seems like people are getting confused by nested #ifdef's, so move the
definitions of crash_kexec_wait_realmode() after the #ifdef CONFIG_SMP
section.
Compile-tested with 32-bit UP, 32-bit SMP and 64-bit SMP configurations.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adapt new API.
Almost change is trivial. Most important change is the below line
because we plan to change task->cpus_allowed implementation.
- ctx->cpus_allowed = current->cpus_allowed;
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent 64-bit server processors (POWER6 and POWER7) have a "Come-From
Address Register" (CFAR), that records the address of the most recent
branch or rfid (return from interrupt) instruction for debugging purposes.
This saves the value of the CFAR in the exception entry code and stores
it in the exception frame. We also make xmon print the CFAR value in
its register dump code.
Rather than extend the pt_regs struct at this time, we steal the orig_gpr3
field, which is only used for system calls, and use it for the CFAR value
for all exceptions/interrupts other than system calls. This means we
don't save the CFAR on system calls, which is not a great problem since
system calls tend not to happen unexpectedly, and also avoids adding the
overhead of reading the CFAR to the system call entry path.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we take an interrupt or exception from kernel mode and the stack
pointer is obviously not a kernel address (i.e. the top bit is 0), we
switch to an emergency stack, save register values and panic. However,
on 64-bit server machines, we don't actually save the values of r9 - r13
at the time of the interrupt, but rather values corrupted by the
exception entry code for r12-r13, and nothing at all for r9-r11.
This fixes it by passing a pointer to the register save area in the paca
through to the bad_stack code in r3. The register values are saved in
one of the paca register save areas (depending on which exception this
is). Using the pointer in r3, the bad_stack code now retrieves the
saved values of r9 - r13 and stores them in the exception frame on the
emergency stack. This also stores the normal exception frame marker
("regshere") in the exception frame.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Icswx is a PowerPC instruction to send data to a co-processor. On Book-S
processors the LPAR_ID and process ID (PID) of the owning process are
registered in the window context of the co-processor at initialization
time. When the icswx instruction is executed the L2 generates a cop-reg
transaction on PowerBus. The transaction has no address and the
processor does not perform an MMU access to authenticate the transaction.
The co-processor compares the LPAR_ID and the PID included in the
transaction and the LPAR_ID and PID held in the window context to
determine if the process is authorized to generate the transaction.
The OS needs to assign a 16-bit PID for the process. This cop-PID needs
to be updated during context switch. The cop-PID needs to be destroyed
when the context is destroyed.
Signed-off-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Tseng-Hui (Frank) Lin <thlin@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes MMU_FTR_TLBIE_206 as we can now use CPU_FTR_HVMODE_206. It
also changes the logic to select which tlbie to use to be based on this
new CPU feature bit.
This also duplicates the ASM_FTR_IF/SET/CLR defines for CPU features
(copied from MMU features).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
sysctl: net: call unregister_net_sysctl_table where needed
Revert: veth: remove unneeded ifname code from veth_newlink()
smsc95xx: fix reset check
tg3: Fix failure to enable WoL by default when possible
networking: inappropriate ioctl operation should return ENOTTY
amd8111e: trivial typo spelling: Negotitate -> Negotiate
ipv4: don't spam dmesg with "Using LC-trie" messages
af_unix: Only allow recv on connected seqpacket sockets.
mii: add support of pause frames in mii_get_an
net: ftmac100: fix scheduling while atomic during PHY link status change
usbnet: Transfer of maintainership
usbnet: add support for some Huawei modems with cdc-ether ports
bnx2: cancel timer on device removal
iwl4965: fix "Received BA when not expected"
iwlagn: fix "Received BA when not expected"
dsa/mv88e6131: fix unknown multicast/broadcast forwarding on mv88e6085
usbnet: Resubmit interrupt URB if device is open
iwl4965: fix "TX Power requested while scanning"
iwlegacy: led stay solid on when no traffic
b43: trivial: update module info about ucode16_mimo firmware
...
Added support for ibm,configure-pe RTAS call introduced with
PAPR 2.2.
Signed-off-by: Richard A. Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some of the 64bit PPC CPU features are MMU-related, so this patch moves
them to MMU_FTR_ bits. All cpu_has_feature()-style tests are moved to
mmu_has_feature(), and seven feature bits are freed as a result.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
RTAS returns extended error codes as a hint of how long the
OS might want to wait before retrying a call. If we have nothing
else useful to do we may as well call back straight away.
This was found when testing the new dynamic dma window feature.
Firmware split the zeroing of the TCE table into 32k chunks but
returned 9901 (which is a suggested wait of 10ms). All up this took
about 10 minutes to complete since msleep is jiffies based and will
round 10ms up to 20ms.
With the patch below we take 3 seconds to complete the same test.
The hint firmware is returning in the RTAS call should definitely
be decreased, but even if we slept 1ms each iteration this would
take 32s.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The calculation of the size for the exception save area of the TLB
miss handler is wrong, luckily it's too big not too small.
Rework it to make it a bit clearer, and also correct. We want 3 save
areas, each EX_TLB_SIZE _bytes_.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We check MSR_SF a lot in sstep.c, to decide if we need to emulate the
truncation of values when running in 32-bit mode. Factor out that code
into a helper, and convert it and the other uses to use MSR_64BIT.
This fixes a bug on BOOK3E where kprobes would end up returning to a
32-bit address, because regs->nip was truncated, because (msr & MSR_SF)
was false.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new MSR_64BIT in a few places. Some of these are already ifdef'ed
for BOOKE vs BOOKS, but it's still clearer, MSR_SF does not immediately
parse as "MSR bit for 64bit".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The MSR bit which indicates 64-bit-ness is different between server and
booke, so add a #define which gives you the right mask regardless.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
BT_L2CAP and BT_SCO have changed to bool .
Value 'm' has invalid .
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit ec775d0e70 ("powerpc: Convert to new irq_*
function names") changed a call from set_irq_chip_data() to
irq_set_chip_data(), but forgot to update the corresponding debug message
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This can be useful for differentiating interrupts on the same host
but with different chip data.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we don't find ibm,associativity-reference-points as a child of
/rtas, look for it at the root of the tree instead. We use this on
Book3E where we have no RTAS but still use the sPAPR conventions
for NUMA.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Even when no initfunc is provided.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The goal is to avoid adding overhead to MMIO when only PIO is needed
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The DSCR (aka Data Stream Control Register) is supported on some
server PowerPC chips and allow some control over the prefetch
of data streams.
This patch allows the value to be specified per thread by emulating
the corresponding mfspr and mtspr instructions. Children of such
threads inherit the value. Other threads use a default value that
can be specified in sysfs - /sys/devices/system/cpu/dscr_default.
If a thread starts with non default value in the sysfs entry,
all children threads inherit this non default value even if
the sysfs value is changed later.
Signed-off-by: Alexey Kardashevskiy <aik@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we set up the TLB for ourselves on Book3E, we need to flush out any
old mappings established by the firmware or bootloader. At present we
attempt this with a tlbilx to flush everything, but this will leave behind
any entries with the IPROT bit set.
There are several good reason firmware might establish mappings with IPROT,
and in fact ePAPR compliant firmwares are required to establish their
initial mapped area with IPROT.
This patch, therefore adds more complex code to scan through the TLB upon
entry and flush away any entries that are not our own.
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An erratum on A2 can lead to the bolted entry we insert for the linear
mapping being evicted, to avoid that write the bolted entry to way 3.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In exc_lvl_ctx_init() we index into the crit/dbg/mcheck stacks using
the hard cpu id, but that assumes the hard cpu id is zero based and
contiguous. That is not the case on A2.
The root of the problem is that the 32bit code has no equivalent of the
paca to allow it to do the hard->soft mapping in assembler. Until the
32bit code is updated to handle that, index the stacks using the soft
cpu ids on 64bit and hard on 32 bit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the cputable entry, regs and setup & restore entries for
the PowerPC A2 core.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While the tracer accesses ptrace breakpoints, the child task may
concurrently exit due to a SIGKILL and thus release its breakpoints
at the same time. We can then dereference some freed pointers.
To fix this, hold a reference on the child breakpoints before
manipulating them.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Prasad <prasad@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: v2.6.33.. <stable@kernel.org>
Link: http://lkml.kernel.org/r/1302284067-7860-4-git-send-email-fweisbec@gmail.com
mac-fec.c was setting individual UDP address registers instead of multicast
group address registers when joining a multicast group.
This prevented from correctly receiving UDP multicast packets.
According to datasheet, replaced hash_table_high and hash_table_low
with grp_hash_table_high and grp_hash_table_low respectively.
Also renamed hash_table_* with grp_hash_table_* in struct fec declaration
for 8xx: these registers are used only for multicast there.
Tested on a MPC5121 based board.
Build tested also against mpc866_ads_defconfig.
Signed-off-by: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As well as searching for nodes with type = "nvram", search for nodes
that have compatible = "nvram". This can't be converted into a single
call to of_find_compatible_node() with a non-NULL type, because that
searches for a node that has _both_ type & compatible = "nvram".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An upcoming new ics backend will need to implement different matching
semantics to the current ones, which are essentially the RTAS ics
backends. So move the current match into the RTAS backend, and allow
other ics backends to override.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SCOM is a side-band configuration bus implemented on some processors.
This code provides a way for code to map and operate on devices via
SCOM, while the details of how that is implemented is left up to a
SCOM "controller" in the platform code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are a few places we patch instructions without using
patch_instruction and patch_branch, probably because they
predated it. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we allocate the stale_map for a cpu when it comes online,
this leaves open a small window where a process can be scheduled
on the cpu before the stale_map is allocated. Instead allocate
the stale_map at CPU_UP_PREPARE time, that way it will be always
available before tasks start running.
It is possible the cpu fails to come up, in which case we should free
the stale_map, so add a CPU_UP_CANCELED case to do that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we start a cpu we use smp_ops->kick_cpu(), which currently
returns void, it should be able to fail. Convert it to return
int, and update all uses.
Convert all the current error cases to return -ENOENT, which is
what would eventually be returned by __cpu_up() currently when
it doesn't detect the cpu as coming up in time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a first cut at making bootwrapper code which will
produce a zImage compliant with the requirements set down
by ePAPR.
This is a very simple bootwrapper, taking the device tree
blob supplied by the ePAPR boot program and passing it on
to the kernel. It builds on the earlier patch to build a
relocatable ET_DYN zImage to meet the other ePAPR image
requirements.
For good measure we have some paranoid checks which will
generate warnings if some of the ePAPR entry condition
guarantees are not met.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds code, linker script and makefile support to allow
building the zImage wrapper around the kernel as a position independent
executable. This results in an ET_DYN instead of an ET_EXEC ELF output
file, which can be loaded at any location by the firmware and will
process its own relocations to work correctly at the loaded address.
This is of interest particularly since the standard ePAPR image format
must be an ET_DYN (although this patch alone is not sufficient to
produce a fully ePAPR compliant boot image).
Note for now we don't enable building with -pie for anything.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On Book3E, MMU_NO_CONTEXT != 0, but the slice_mm_new_context()
macro assumes that it is. This means that the map of the
page sizes for each slice is always initialized to zeroes
(which happens to be 4k pages), rather than to the correct
default base page size value - which might be 64k.
This patch corrects the problem.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use MMU_NO_CONTEXT as the initialiser for mm_context.id on
nohash and hash64.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to do that to guarantee they see any code change done by
dynamic patching during boot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wakeup comes from the system reset handler with a potential loss of
the non-hypervisor CPU state. We save the non-volatile state on the
stack and a pointer to it in the PACA, which the system reset handler
uses to restore things
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to wait a bit for them to have done their CPU setup
or we might end up with translation and EE on with different
LPCR values between threads
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We do it before we loop on the PACA start flag. This way, we get a
chance to set critical SPRs on all CPUs before Linux tries to start
them up, which avoids problems when changing some bits such as LPCR
bits that need to be identical on all threads of a core or similar
things like that. Ideally, some of that should also be done before
the MMU is enabled, but that's a separate issue which would require
moving some of the SMP startup code earlier, let's not get there
for now, it works with that change alone.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This sets the default data stream prefetch size for operating
systems that don't set their own value in DSCR. We use 4 which
is "medium".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This uses feature sections to arrange that we always use HSPRG1
as the scratch register in the interrupt entry code rather than
SPRG2 when we're running in hypervisor mode on POWER7. This will
ensure that we don't trash the guest's SPRG2 when we are running
KVM guests. To simplify the code, we define GET_SCRATCH0() and
SET_SCRATCH0() macros like the GET_PACA/SET_PACA macros.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rework exception macros a bit to split offset from vector and add
some basic support for HDEC, HDSI, HISI and a few more.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pass the register type to the prolog, also provides alternate "HV"
version of hardware interrupt (0x500) and adjust LPES accordingly
We tag those interrupts by setting bit 0x2 in the trap number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running in Hypervisor mode (arch 2.06 or later), we store the PACA
in HSPRG0 instead of SPRG1. The architecture specifies that SPRGs may be
lost during a "nap" power management operation (though they aren't
currently on POWER7) and this enables use of SPRG1 by KVM guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This bit indicates that we are operating in hypervisor mode on a CPU
compliant to architecture 2.06 or later (currently server only).
We set it on POWER7 and have a boot-time CPU setup function that
clears it if MSR:HV isn't set (booting under a hypervisor).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Even when nothing is specified in the device tree, and despite the
fact that we don't setup links properly yet, we still need a reasonable
value in there or some interrupts won't be setup properly to point to
an existing processor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds more SPR definitions used on newer processors when running
in hypervisor mode. Along with some other P7 specific bits and pieces
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a significant rework of the XICS driver, too significant to
conveniently break it up into a series of smaller patches to be honest.
The driver is moved to a more generic location to allow new platforms
to use it, and is broken up into separate ICP and ICS "backends". For
now we have the native and "hypervisor" ICP backends and one common
RTAS ICS backend.
The driver supports one ICP backend instanciation, and many ICS ones,
in order to accomodate future platforms with multiple possibly different
interrupt "sources" mechanisms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Because of speculative event roll back, it is possible for some event coutners
to decrease between reads on POWER7. This causes a problem with the way that
counters are updated. Delta calues are calculated in a 64 bit value and the
top 32 bits are masked. If the register value has decreased, this leaves us
with a very large positive value added to the kernel counters. This patch
protects against this by skipping the update if the delta would be negative.
This can lead to a lack of precision in the coutner values, but from my testing
the value is typcially fewer than 10 samples at a time.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This problem was noticed on an MPC855T platform. Ftrace did oops
when trying to write to the kernel text segment.
Many thanks to Joakim for finding the root cause of this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We currently enable interrupts before the dispatch log for the boot
cpu is setup. If a timer interrupt comes in early enough we oops in
scan_dispatch_log:
Unable to handle kernel paging request for data at address 0x00000010
...
.scan_dispatch_log+0xb0/0x170
.account_system_vtime+0xa0/0x220
.irq_enter+0x88/0xc0
.do_IRQ+0x48/0x230
The patch below adds a check to scan_dispatch_log to ensure the
dispatch log has been allocated.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PAPR specifies that DTL buffers can not cross AMS environments (aka CMO
in the PAPR) and can not cross a memory entitlement granule boundary
(4k). This is found in section 14.11.3.2 H_REGISTER_VPA of the PAPR.
kmalloc does not guarantee an alignment of the allocation, though,
beyond 8 bytes (at least in my understanding). Create a special kmem
cache for DTL buffers with the alignment requirement.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent commit b987812b3f caused
a compile failure on UP because a considerably large block
of the file was included within CONFIG_SMP, hence making a stub
function not exposed on UP builds when it needed to be.
Relocate the stub to the #else /* ! CONFIG_SMP */ section
and also annotate the relevant else/endif so that nobody
else falls into the same trap I did.
Reported-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix a possible problem with mport registration left non-cleared after
fsl_rio_setup() exits on link error. Abort mport initialization if
registration failed.
This patch is applicable to 2.6.39-rc1 only. The problem does not exist
for earlier versions.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
We currently dont have CPU Hotplug support working on 85xx so we need to
disable Suspsend support as it will force enabling of CPU Hotplug.
arch/powerpc/kernel/built-in.o: In function `cpu_die': arch/powerpc/kernel/smp.c:702: undefined reference to `start_secondary_resume'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
e500mc does not support the HID0/MSR mechanism that is used by e500_idle
(and there are also issues with waking on certain types of interrupts).
Further, even if napping is never actually enabled, just having
CPU_FTR_CAN_NAP will cause machine_init() to overwrite the board's supplied
ppc_md.power_save().
We drop CPU_FTR_MAYBE_CAN_DOZE becuase we should use 'wait' instead on
e500mc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CPU_FTRS_POSSIBLE and CPU_FTRS_ALWAYS defines did not encompass
e5500 CPU features when built for 64-bit. This causes issues with
cpu_has_feature() as it utilizes the POSSIBLE & ALWAYS defines as part
of its check.
Create a unique CPU_FTRS_E5500 (as its different from CPU_FTRS_E500MC),
created a new group for 64-bit Book3e based CPUs and add CPU_FTRS_E5500
to that group.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
serial port nodes with the property status="disabled" are not usable and so
avoid adding "disabled" port with the system.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCIe nodes with the property status="disabled" are not usable and so
avoid adding "disabled" PCIe bridge with the system.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Xen save/restore is going to use hibernate device callbacks for
quiescing devices and putting them back to normal operations and it
would need to select CONFIG_HIBERNATION for this purpose. However,
that also would cause the hibernate interfaces for user space to be
enabled, which might confuse user space, because the Xen kernels
don't support hibernation. Moreover, it would be wasteful, as it
would make the Xen kernels include a substantial amount of code that
they would never use.
To address this issue introduce new power management Kconfig option
CONFIG_HIBERNATE_CALLBACKS, such that it will only select the code
that is necessary for the hibernate device callbacks to work and make
CONFIG_HIBERNATION select it. Then, Xen save/restore will be able to
select CONFIG_HIBERNATE_CALLBACKS without dragging the entire
hibernate code along with it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
Commit b3df895aeb "powerpc/kexec: Add support for FSL-BookE"
introduced the original PPC_STD_MMU_64 checks around the function
crash_kexec_wait_realmode(). Then commit c2be05481f
"powerpc: Fix default_machine_crash_shutdown #ifdef botch" changed
the ifdef around the calling site to add a check on SMP, but the
ifdef around the function itself was left unchanged, leaving an
unused function for PPC_STD_MMU_64=y and SMP=n
Rather than have two ifdefs that can get out of sync like this,
simply put the corrected conditional around the function and use
a stub to get rid of one set of ifdefs completely.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some minor typos:
* informations => information
* there own => their own
* these => this
Signed-off-by: Sylvestre Ledru <sylvestre.ledru@scilab.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCIe memory address space is 1:1 mapped with u-boot.
Update dts of Px020RDB i.e. P1020RDB and P2020RDB to match the address map
changes in u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Instead of creating idle threads at boot for all possible CPUs, we
create them on demand, like x86 or ARM, and we properly call init_idle
to re-initialize an idle thread when a CPU was unplugged and is now
re-plugged.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead, keep it static, expose an accessor and use that from
the PowerMac code. Avoids easy namespace collisions and will
make it easier to consolidate with other implementations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On some machines that use i2c to synchronize the timebases (such
as PowerMac7,2/7,3 G5 machines), hotplug CPU would crash when
putting back a new CPU online due to the underlying i2c bus being
closed.
This uses the newly added bringup_done() callback to move the close
along with other housekeeping calls, and adds a CPU notifier to
re-open the i2c bus around subsequent hotplug operations
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows us to stop abusing smp_ops->setup_cpu() for cleanup
tasks that have to take place after the initial boot time CPU
bringup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code soft-disables, and then goes to NAP mode which
turns interrupts on. That means that if an interrupt occurs, we
will hit the masked interrupt code path which isn't what we want,
as it will return with EE off, which will either get us out of
NAP mode, or fail to enter it (according to spec).
Instead, let's just rely on the fact that it is safe to take
decrementer interrupts on an offline CPU and leave interrupts
enabled. We can also get rid of the special case in asm for
power4_cpu_offline_powersave() and just use power4_idle().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those instructions do nothing on non-threaded processors such
as 970's used on those machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the generic code, just add the MPIC priority setting,
I don't see any use in mucking around with the decrementer,
as 32-bit will have EE off all along, and 64-bit will be able
to deal with it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use generic cpu_state, call idle_task_exit() properly, and
remove smp_core99_cpu_die() which isn't useful, the generic
function does the job just fine.
Remove the last remnants of cpu_enable(), everybody uses the normal
__cpu_up() path now
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is used by some "soft" hotplug implementations. I needs to
call idle_task_exit() when the CPU is going away, and we remove
the now no-longer needed set_cpu_online() and local_irq_enable()
which are handled by the return to start_secondary
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Various thing are torn down when a CPU is hot-unplugged. That CPU
is expected to go back to start_secondary when re-plugged to re
initialize everything, such as clock sources, maps, ...
Some implementations just return from cpu_die() callback
in the idle loop when the CPU is "re-plugged". This is not enough.
We fix it using a little asm trampoline which resets the stack
and calls back into start_secondary as if we were all fresh from
boot. The trampoline already existed on ppc64, but we add it for
ppc32
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With some implementations, it is possible that a timer interrupt
occurs every few seconds on an offline CPU. In this case, just
re-arm the decrementer and return immediately
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
avr32: Fix missing irq namespace conversion
powerpc: qe_ic: Rename get_irq_desc_data and get_irq_desc_chip
genirq: Remove the now obsolete config options and select statements
arm: versatile : Fix typo introduced in irq namespace cleanup
sound: Fixup the last user of the old irq functions
genirq: Remove obsolete comment
genirq: Remove now obsolete set_irq_wake()
sh: Fix irq cleanup fallout
x86: apb_timer: Fixup genirq fallout
genirq: Fix misnamed label in handle_edge_eoi_irq
Fix up crazy conflict in arch/powerpc/include/asm/qe_ic.h:
- commit eead4d5c63 ("powerpc: qe_ic: Rename get_irq_desc_data and
get_irq_desc_chip") made the helper functions use
irq_desc_get_handler_data() instead of the legacy (and no longer
existing) get_irq_desc_data.
- commit d4db35e8dc ("powerpc/qe_ic: Fix another breakage from the
irq_data conversion") used irq_desc_get_chip_data() instead.
According to Thomas, the former is the correct direct conversion, but it
does look like both should work (arch/powerpc/sysdev/qe_lib/qe_ic.c
seems to initialize both to the same thing), and the chip data in some
ways is the more logical. Somebody should really decide on one of the
other.
This merge picks irq_desc_get_handler_data() as the straightforward pure
conversion to new names, as per Thomas.
These two functions disappeared in commit
0c6f8a8b91
"genirq: Remove compat code"
but they still exist in qe_ic.h.
This patch renames the function to their new names.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <20110330132504.GA31832@riccoc20.at.omicron.at>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Ensure the Chelsio T3/T4 network drivers and iWARP drivers are
enabled in the pseries config.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent upstream builds with allmodconfig fail due to lack of space
between 0x3000 and 0x6000. We have a hard block at 0x7000 but we can
spare a page by moving the STAB0 from 0x6000 to 0x8000.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit cf9efce0ce (powerpc: Account time using timebase rather
than PURR) used in_irq() to detect if the time was spent in
interrupt processing. This only catches hardirq context so if we
are in softirq context and in the idle loop we end up accounting it
as idle time. If we instead use in_interrupt() we catch both softirq
and hardirq time.
The issue was found when running a network intensive workload. top
showed the following:
0.0%us, 1.1%sy, 0.0%ni, 85.7%id, 0.0%wa, 9.9%hi, 3.3%si, 0.0%st
85.7% idle. But this was wildly different to the perf events data.
To confirm the suspicion I ran something to keep the core busy:
# yes > /dev/null &
8.2%us, 0.0%sy, 0.0%ni, 0.0%id, 0.0%wa, 10.3%hi, 81.4%si, 0.0%st
We only got 8.2% of the CPU for the userspace task and softirq has
shot up to 81.4%.
With the patch below top shows the correct stats:
0.0%us, 0.0%sy, 0.0%ni, 5.3%id, 0.0%wa, 13.3%hi, 81.3%si, 0.0%st
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a given firmware doesn't have a token to support query-cpu-stopped-state,
its not likely to change during the lifetime of the kernel.
Only print this information once, not once per secondary thread.
While here, make the line wrap grep friendly.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To try to avoid future confusion, rename irq to hwirq when it refers
to a xics domain number instead of a linux irq number.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 79f26c268e (powerpc:
platforms/pseries irq_data conversion) pushed irq_desc down into many
functions, dererencing the descriptor irq field as late as possible.
But it incorrectly passed a linix virtural irq number to RTAS,
resulting in the interrupt not being disabled and possibly
other bad things, such as another interrupt being disabled and/or
a checkstop.
In addition this missed the point of xics_mask_unknown_vec and
the seperation of xics_mask_real_irq from xics_mask_irq. When
xics_mask_unknown_vec is called it's because the hardware delivered an
irq source for which we have no linux irq allocated, and thefore we can
not have an irq_desc allocated.
Revert xics_mask_real_irq to its prior version, naming the argument
hwirq to highlight the difference.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These syscalls have been added recently:
name_to_handle_at
open_by_handle_at
clock_adjtime
syncfs
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
339 is the SPR number for MAS5 documented by Power ISA 2.06, and
implemented by e500mc. It is not yet used anywhere in the kernel,
so nothing should be relying on the wrong number.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pfns are unsigned long, but MEMORY_START is phys_addr_t. This leads
to page_to_pfn() returning phys_addr_t, and thus type mismatches in a few
print statements.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is used by Alsa to mmap buffers allocated with dma_alloc_coherent()
into userspace. We need a special variant to handle machines with
non-coherent DMAs as those buffers have "special" virt addresses and
require non-cachable mappings
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For normal halt, reboot, and poweroff events, refrain from overwriting
the lnx,oops-log partition. Also, don't save the dmesg buffer on an
emergency-restart event if we've already saved it earlier in panic().
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Uwe Kleine-König reported:
while working on an defconfig (arm/mx27) I noticed that just updating
it[1] results in removing CONFIG_EEPROM_AT24=y. The reason is that
since commit
v2.6.36-5965-g5f2365d (misc devices: do not enable by default)
MISC_DEVICES isn't enabled anymore by default. So all defconfigs that
have CONFIG_SOME_SYMBOL=y (or =m) (with SOME_SYMBOL depending on
MISC_DEVICES) but not CONFIG_MISC_DEVICES=y suffer from the same
problem.
This restores those misc devices to the powerpc defconfigs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Uwe Kleine-König
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates the LEVEL flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates IRQ_LEVEL.
Use irq_data to get the level type information in the chip functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Retrieve the IRQ_LEVEL information from irq_data which avoids a
redundant sparse irq lookup as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The level flag is
updated in the core as well.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core code provides the same functionality when the
IRQCHIP_EOI_IF_HANDLED flag is set for the irq chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core irq_set_type() function updates the flow type when the chip
callback returns 0. It also updates irq_data, so this can be used in
irq_ack() to check for the level bit. That avoids a redundant sparse
irq lookup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The irq chip has no irq_set_type() callback. So calling the call is
pointless. Set IRQ_LEVEL via the proper accessor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit ddd588b5dd ("oom: suppress nodes that are not allowed from
meminfo on oom kill") moved lib/show_mem.o out of lib/lib.a, which
resulted in build warnings on all architectures that implement their own
versions of show_mem():
lib/lib.a(show_mem.o): In function `show_mem':
show_mem.c:(.text+0x1f4): multiple definition of `show_mem'
arch/sparc/mm/built-in.o:(.text+0xd70): first defined here
The fix is to remove __show_mem() and add its argument to show_mem() in
all implementations to prevent this breakage.
Architectures that implement their own show_mem() actually don't do
anything with the argument yet, but they could be made to filter nodes
that aren't allowed in the current context in the future just like the
generic implementation.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: James Bottomley <James.Bottomley@hansenpartnership.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
deal with races in /proc/*/{syscall,stack,personality}
proc: enable writing to /proc/pid/mem
proc: make check_mem_permission() return an mm_struct on success
proc: hold cred_guard_mutex in check_mem_permission()
proc: disable mem_write after exec
mm: implement access_remote_vm
mm: factor out main logic of access_process_vm
mm: use mm_struct to resolve gate vma's in __get_user_pages
mm: arch: rename in_gate_area_no_task to in_gate_area_no_mm
mm: arch: make in_gate_area take an mm_struct instead of a task_struct
mm: arch: make get_gate_vma take an mm_struct instead of a task_struct
x86: mark associated mm when running a task in 32 bit compatibility mode
x86: add context tag to mark mm when running a task in 32-bit compatibility mode
auxv: require the target to be tracable (or yourself)
close race in /proc/*/environ
report errors in /proc/*/*map* sanely
pagemap: close races with suid execve
make sessionid permissions in /proc/*/task/* match those in /proc/*
fix leaks in path_lookupat()
Fix up trivial conflicts in fs/proc/base.c
The Xen PV drivers in a crashed HVM guest can not connect to the dom0
backend drivers because both frontend and backend drivers are still in
connected state. To run the connection reset function only in case of a
crashdump, the is_kdump_kernel() function needs to be available for the PV
driver modules.
Consolidate elfcorehdr_addr, setup_elfcorehdr and saved_max_pfn into
kernel/crash_dump.c Also export elfcorehdr_addr to make is_kdump_kernel()
usable for modules.
Leave 'elfcorehdr' as early_param(). This changes powerpc from __setup()
to early_param(). It adds an address range check from x86 also on ia64
and powerpc.
[akpm@linux-foundation.org: additional #includes]
[akpm@linux-foundation.org: remove elfcorehdr_addr export]
[akpm@linux-foundation.org: fix for Tejun's mm/nobootmem.c changes]
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no user now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removes resource reservation from the common sybsystem initialization code
and make it part of mport driver initialization. This resolves conflict
with resource reservation by device specific mport drivers.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes mport ID and host destination ID assignment to implement unified
method common to all mport drivers. Makes "riohdid=" kernel command line
parameter common for all architectures with support for more that one host
destination ID assignment.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Subsystem initialization sequence modified to support presence of multiple
RapidIO controllers in the system. The new sequence is compatible with
initialization of PCI devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Add an option to include RapidIO support if the PCI is available.
2. Add FSL_RIO configuration option to enable controller selection.
3. Add RapidIO support option into x86 and MIPS architectures.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>