CHARGE_FULL should represent the full capacity of the battery in uAh.
The 0x10 (FullCAP) register shows the compensated full capacity in
mAh * 2; e.g., reg(0x10) = 0xBB8 means that it is 1500mAh.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Remove the duplicate.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Factor out some boilerplate code for i2c driver registration
into module_i2c_driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Woogyom Kim <milo.kim@ti.com>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Peter Edwards <sweetlilmre@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add MODULE_DEVICE_TABLE to setup modalias for lp8727. Allows auto
modprobing.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch fixes the following warning and makes the code a little
bit more simpler:
CC drivers/power/charger-manager.o
charger-manager.c: In function 'charger_get_property':
charger-manager.c:429:15: warning: 'i' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch includes below changes:
* Some code change for better readability.
* Current code in probe already ensures desc->charger_regulators
is not NULL. No need to check if it is NULL or not before calling
regulator_bulk_free().
* Use dev_get_drvdata() in cm_suspend_prepare() and cm_suspend_complete()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Use the module_platform_driver() macro which makes the code smaller
and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add missing platform_set_drvdata in da9052_bat_probe.
Otherwise, calling platform_get_drvdata in da9052_bat_remove returns NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The patch fixes the following sparse warning:
drivers/power/ab8500_charger.c:1619:6: warning: symbol 'ab8500_charger_detect_usb_type_work' was not declared. Should it be static?
drivers/power/abx500_chargalg.c:1709:24: warning: symbol 'abx500_chargalg_sysfs_ops' was not declared. Should it be static?
drivers/power/ab8500_fg.c:2328:24: warning: symbol 'ab8500_fg_sysfs_ops' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
ab8500_fg_discharge_state_to() function should accept
'enum ab8500_fg_discharge_state' argument, not
'enum ab8500_fg_charge_state'.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The struct is duplicated, plus causes the following flood:
CC drivers/power/ab8500_fg.o
ab8500_fg.c: In function ‘ab8500_fg_get_ext_psy_data’:
b8500_fg.c:2081:8: warning: assignment from incompatible pointer type [enabled by default]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The struct is duplicated, plus when used it causes the following
warnings:
CHECK drivers/power/ab8500_fg.c
ab8500_fg.c:818:13: warning: incorrect type in assignment (different base types)
ab8500_fg.c:818:13: expected struct v_to_cap *tbl
ab8500_fg.c:818:13: got struct abx500_v_to_cap *const v_to_cap_tbl
CC drivers/power/ab8500_fg.o
ab8500_fg.c: In function 'ab8500_fg_volt_to_capacity':
ab8500_fg.c:818:6: warning: assignment from incompatible pointer type [enabled by default]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This is the same as abx500_adc_therm, but when the former is used,
the following warning flood pops up:
drivers/power/ab8500_btemp.c: In function 'ab8500_btemp_batctrl_volt_to_res':
ab8500_btemp.c:150:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c: In function 'ab8500_btemp_curr_source_enable':
ab8500_btemp.c:212:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c:244:32: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c: In function 'ab8500_btemp_measure_temp':
ab8500_btemp.c:462:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c: In function 'ab8500_btemp_id':
ab8500_btemp.c:528:121: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c:551:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
This patch fixes the issue by switching the driver to use more
namespace-friendly enum.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch fixes the following build errors:
ab8500_charger.c: In function 'ab8500_charger_remove':
ab8500_charger.c:2519:2: error: implicit declaration of function 'otg_unregister_notifier' [-Werror=implicit-function-declaration]
ab8500_charger.c:2520:2: error: implicit declaration of function 'otg_put_transceiver' [-Werror=implicit-function-declaration]
ab8500_charger.c: In function 'ab8500_charger_probe':
ab8500_charger.c:2688:2: error: implicit declaration of function 'otg_get_transceiver' [-Werror=implicit-function-declaration]
ab8500_charger.c:2688:10: warning: assignment makes pointer from integer without a cast [enabled by default]
ab8500_charger.c:2695:2: error: implicit declaration of function 'otg_register_notifier' [-Werror=implicit-function-declaration]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This driver is responsible for battery detection, obtaining battery
temperature and monitor the battery temperature by taking precautionary
measurements when battery temperature goes beyond or below the thresholds.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This driver is responsible for provide battery parameters to user space via
sysfs by registers to power supply class. It uses fuel gauge and gpadc driver
in obtaining the battery parameters. These battery properties are used by
abx500 charging algorithm driver to monitor the battery.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This driver is responsible for detecting the ac/usb plugin and also includes
function to enable ac/usb charging and re-kick the watchdog.
It registers with the power supply class and provides information to the user
space. The information include status of ac/usb charger device.
This information in turn will be used by the abx500 charging algorithm driver
to enable/disable and monitor charging.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This is a charging algorithm driver for abx500 variants. It is the central
entity for battery driver and is responsible for charging and monitoring
the battery driver. It is a hardware independant driver and also monitors
other abx500 power supply devices.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Driver support for the Summit I²C battery charger. This is used in some
Intel devices.
Signed-off-by: Bruce E. Robertson <bruce.e.robertson@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
We enable power, but don't disable it in case of an error.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Definition of STATUS2
: remove space before tabs.
Return code of lp8727_is_dedicated_charger(), lp8727_is_usb_charger()
: remove parentheses when return is not a function.
MODULE_AUTHOR section
: remove space at the start of a line.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
On writing single byte via i2c, use i2c_smbus_write_byte_data()
rather than i2c_smbus_write_i2c_block_data().
Name changes :
lp8727_i2c_read() -> lp8727_read_bytes()
lp8727_i2c_write() -> removed
lp8727_i2c_read_byte() -> lp8727_read_byte()
lp8727_i2c_write_byte() -> lp8727_write_byte()
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add error checking on initializing registers and interrupt handler.
Initializing registers - lp8727_init_device()
: check i2c error during probing the driver.
Initializing interrupt handler - lp8727_intr_config()
: check an error on creating the irq thread.
If an error occurs on probing lp8727 driver, allocated lp8727 driver memory is freed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add 'Texas Instruments' because TI acquired National semiconductor at 2011.
And the driver information is added in the header file.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Allow both device tree (preferred) and platform data-based driver
instantiation.
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This allows us to simplify probe and exit function.
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The SOC register (0dh) reports the state of charge before empty
compensation adjustments are applied. The max value reported by this
register will decrease as the battery ages.
Use the RepSOC register (06h) to report the capacity of the
battery. RepSOC contains a filtered version of the battery capacity
after empty compensation adjustments have been applied.
Reported-by: Gary Keyes <gary.e.keyes@intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
If platform has the alert pin attached to an interrupt source have the
driver signal a change in the SOC every 1 percent.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add power on reset (POR) init procedure defined by the maxim
appnote. Using this procedure ensures that the part is
configured/initialized correctly at POR and improves early accuracy of
the fuel gauge and informs the fuel gauge with the battery
characterization parameters. The battery characterization parameters
come from the maxim characterization procedure.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The i2c_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Since 43cc71eed1, the platform
modalias is prefixed with "platform:".
Current code has the id_table, thus add MODULE_DEVICE_TABLE will
automatically setup the modalias.
Also make charger_manager_id static as it is only used in this driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
When reading flags, bq27x00_read() argument is inverted and causes
reads 2 of bytes for bq27200 and 1 byte for bq27500, while their register
sizes are 1 and 2 bytes respectively. This causes bq27500 upper flag
bits always to be returned as 0, causing full charge state to never be
reported correctly, so fix it.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This reverts commit 270968c098.
Grazvydas Ignotas wrote:
After 270968c098 "bq27x00_battery: Fix reporting status value for
bq27500 battery" status doesn't seem to be reported correctly when the
battery is close to fully charged state. It reports "Not charging"
while in fact there is >130mA current flowing to the battery according
to current_now.
This status report seems to be based on CHG bit in status register,
but looking at the datasheet the description says "(Fast) charging
allowed", which I guess means that the chip recommends charging and
not that charging is actually going on? If you check the bit while
battery is discharging and it's not full, the bit is also set.
Suggested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.infradead.org/battery-2.6: (68 commits)
power_supply: Mark da9052 driver as broken
power_supply: Drop usage of nowarn variant of sysfs_create_link()
s3c_adc_battery: Average over more than one adc sample
power_supply: Add DA9052 battery driver
isp1704_charger: Fix missing check
jz4740-battery: Fix signedness bug
power_supply: Assume mains power by default
sbs-battery: Fix devicetree match table
ARM: rx51: Add bq27200 i2c board info
sbs-battery: Change power supply name
devicetree-bindings: Propagate bq20z75->sbs rename to dt bindings
devicetree-bindings: Add vendor entry for Smart Battery Systems
sbs-battery: Rename internals to new name
bq20z75: Rename to sbs-battery
wm97xx_battery: Use DEFINE_MUTEX() for work_lock
max8997_charger: Remove duplicate module.h
lp8727_charger: Some minor fixes for the header
lp8727_charger: Add header file
power_supply: Convert drivers/power/* to use module_platform_driver()
power_supply: Add "unknown" in power supply type
...
There are some problems with MFD part of this driver, so the
driver fails to build:
drivers/power/da9052-battery.c: In function 'da9052_bat_read_volt':
drivers/power/da9052-battery.c:293:2: error: implicit declaration of function 'da9052_adc_manual_read' [-Werror=implicit-function-declaration]
drivers/power/da9052-battery.c: In function 'da9052_bat_check_presence':
drivers/power/da9052-battery.c:306:2: error: implicit declaration of function 'da9052_adc_read_temp' [-Werror=implicit-function-declaration]
drivers/power/da9052-battery.c: In function 'da9052_determine_vc_tbl_index':
drivers/power/da9052-battery.c:348:1: warning: control reaches end of non-void function [-Wreturn-type]
cc1: some warnings being treated as errors
The fix for MFD part will probably go post -rc1 (or in the next merge
window), so let's disable the driver for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The function is not exported to modules, plus we do want to catch anyone
who tries to create complex hierarchy (in that case we'd need to change
'powers' symlink to a directory, probably under a different name to not
break ABI).
This patch fixes the following build error:
ERROR: "sysfs_create_link_nowarn" [drivers/power/power_supply.ko] undefined!
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Some sources for adc battery information provide only inaccurate results
where the read value differs from the real value with positive and negative
offsets. For such sources it can be more accurate to collect two or more
value sample and use the average of all collected values.
This patch adds pdata options volt_samples, current_samples and
backup_volt_samples to specifiy the number of samples to collect,
reads the specified number of samples and calculates the average of those.
For unset sample-number-values a default of 1 is assumed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Driver for DA9052 battery charger. This driver depends on DA9052 MFD core
dirver for definitions and methods.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
A segfault happens if there's no board information.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Heikki Krogerus <krohei@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
wait_for_completion_interruptible_timeout() may return negative value.
In this case, checking if (t > 0) will return true if t is unsigned.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
If no power class device is found in power_supply_is_system_supplied(),
the function currently returns 0, which basically means that the system
is supposed to be running on battery. In practice, mobile devices tend
to always implement at least one power class device and more often two
(battery and AC adapter). Systems with no registered power class
devices are more likely to be desktop systems, where the system is
always powered by mains.
So, change the default return value of
power_supply_is_system_supplied() from 0 (running on battery) to 1
(running on mains.)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
It should be an of module table, not i2c.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The power supply name used to be fixed as "battery". This change allows
for multiple batteries by generating the name rather than using a fixed
value.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Now that this driver is named more generally, this change updates
the internal variables, defines and functions to use this new name.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This driver for the bq20z75 implemented the register spec defined
by the SBS standard. As this is not unique to this the TI part this
was originally written for, we can generalize this driver to
show its support for any SBS compliant battery.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
work_lock can be initialized automatically with
DEFINE_MUTEX() rather than explicitly calling mutex_init().
This patch also removes an unused bat_lock mutex.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
