Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----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=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
Added one additional parameter to thermal_zone_device_update() to provide
caller with an optional capability to specify reason.
Currently this event is used by user space governor to trigger different
processing based on event code. Also it saves an additional call to read
temperature when the event is received.
The following events are cuurently defined:
- Unspecified event
- New temperature sample
- Trip point violated
- Trip point changed
- thermal device up and down
- thermal device power capability changed
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We get 2 warnings when building kernel with W=1:
drivers/regulator/dbx500-prcmu.c:78:6: warning: no previous prototype for 'ux500_regulator_suspend_debug' [-Wmissing-prototypes]
drivers/regulator/dbx500-prcmu.c:87:6: warning: no previous prototype for 'ux500_regulator_resume_debug' [-Wmissing-prototypes]
In fact, these functions are unused in
dbx500-prcmu.c, but should be removed.
So this patch removes the unused functions.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Three files are modified, the driver, header file and the binding document.
Updates for the regulator source file include and .of_match_table entry
and node match checking in the probe() function for a compatible pv88080
silicon type. A new "HVBUCK" is added in source file and added
regsiter definition in header file for pv88080 bb silicion.
The binding documentation changes have been made to reflect these updates.
Signed-off-by: Eric Jeong <eric.jeong.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drms_uA_update() always returns failure when it cannot find regulator's
input voltage. But if hardware supports load configuration with
ops->set_load() and the input regulator isn't specified with valid reason
such as the input regulator is battery, not finding input voltage is
normal so such case should not return with an error.
Avoid such inadequate error return by checking input/output voltages
only when drms_uA_update() is about to configure load with enum based
ops->set_mode().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
http://www.ti.com/lit/pdf/SWCZ010:
DCDC o/p voltage can go higher than programmed value
Impact:
VDDI, VDD2, and VIO output programmed voltage level can go higher than
expected or crash, when coming out of PFM to PWM mode or using DVFS.
Description:
When DCDC CLK SYNC bits are 11/01:
* VIO 3-MHz oscillator is the source clock of the digital core and input
clock of VDD1 and VDD2
* Turn-on of VDD1 and VDD2 HSD PFETis synchronized or at a constant
phase shift
* Current pulled though VCC1+VCC2 is Iload(VDD1) + Iload(VDD2)
* The 3 HSD PFET will be turned-on at the same time, causing the highest
possible switching noise on the application. This noise level depends
on the layout, the VBAT level, and the load current. The noise level
increases with improper layout.
When DCDC CLK SYNC bits are 00:
* VIO 3-MHz oscillator is the source clock of digital core
* VDD1 and VDD2 are running on their own 3-MHz oscillator
* Current pulled though VCC1+VCC2 average of Iload(VDD1) + Iload(VDD2)
* The switching noise of the 3 SMPS will be randomly spread over time,
causing lower overall switching noise.
Workaround:
Set DCDCCTRL_REG[1:0]= 00.
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The new op is analogous to set_voltage_time_sel. It can be used by
regulators which don't have a table of discrete voltages. The function
returns the time for the regulator output voltage to stabilize after
being set to a new value, in microseconds. If the op is not set a
default implementation is used to calculate the delay.
This change also removes the ramp_delay calculation in the PWM
regulator, since the driver now uses the core code for the calculation
of the delay.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code assumes that only the ramp_delay is used to determine
the time needed for the voltage to stabilize. This may be true for the
calculation done by regulator_set_voltage_time_sel(), however regulators
can implement their own set_voltage_time_sel() op which would be skipped
if no ramp delay is specified. Remove the check in
_regulator_do_set_voltage(), the functions calculating the ramp delay
return 0 anyway when the ramp delay is not configured.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the voltage can not be set jump to the end of the function. This
avoids having to check for an error multiple times and eliminates one
level of nesting in a follow-up change.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
also a switch. The buck regulators support teaming into multi-phase
groups, with A+B, A+B+C, D+E groupings.
Some registers controlling DCDC converter work settings are at different
offsets. Deal with them as well.
Add support for this new variant.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We get 1 warning when building kernel with W=1:
drivers/regulator/hi6421-regulator.c:480:14: warning: no previous prototype for
'hi6421_regulator_ldo_get_optimum_mode' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the rk818 regulator. The regulator module consists
of 4 DCDCs, 9 LDOs, 1 switch and 1 BOOST converter which is used to
power OTG and HDMI5V.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change the MFD config option as per latest naming
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to support the Qualcomm MDM9615 SoC, add support for the
PM8018 RPM regulator in the qcom_rpm-regulator driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix typo in regulator Kconfig for the TPS80031 tristate string (trivial)
Signed-off-by: Sebastiaan Schalbroeck <schalbroeck@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch was based on my missinterpretation of the API and only
accidentally worked for me. Let's clean it out to not confuse others.
This reverts commit 3ff3f518a1.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Linear Technology LTC3676
8-output I2C voltage regulator IC.
Cc: Jaffer Kapasi <jkapasi@linear.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some versions of tps65218 do not seem to support poweroff modes properly
if DCDC3 regulator is shut-down. Thus, keep it enabled even during
poweroff if the version info matches the broken silicon revision.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom iProc,
STMPE and ChromeOS EC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TdEI
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom
iProc, STMPE and ChromeOS EC controllers"
* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
regulator: pwm: Support extra continuous mode cases
pwm: Add ChromeOS EC PWM driver
dt-bindings: pwm: Add binding for ChromeOS EC PWM
mfd: cros_ec: Add EC_PWM function definitions
mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
pwm: atmel: Use of_device_get_match_data()
pwm: atmel: Fix checkpatch warnings
pwm: atmel: Fix disabling of PWM channels
dt-bindings: pwm: Add R-Car H3 device tree bindings
pwm: rcar: Use ARCH_RENESAS
pwm: tegra: Add support for Tegra186
dt-bindings: pwm: tegra: Add compatible string for Tegra186
pwm: tegra: Avoid overflow when calculating duty cycle
pwm: tegra: Allow 100 % duty cycle
pwm: tegra: Add support for reset control
pwm: tegra: Rename mmio_base to regs
pwm: tegra: Remove useless padding
pwm: tegra: Drop NUM_PWM macro
pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
...
The voltage ranges listed here are wrong. The pma8084 pldo
supports three different overlapping voltage ranges with
differing step sizes and the pma8084 ftsmps supports two. These
ranges can be seen in the "native" spmi regulator driver
(qcom_spmi-regulator.c) at pldo_ranges[] and ftsmps_ranges[]
respectively. Port these ranges over to the RPM SMD regulator
driver so that we list the appropriate set of supported voltages
on these types of regulators.
Fixes: ee01d0c91e ("regulator: qcom-smd: Add support for PMA8084")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The voltage ranges listed here are wrong. The correct ranges can
be seen in the "native" spmi regulator driver
qcom_spmi-regulator.c at pldo_ranges[], ftsmps_ranges[] and
boost_ranges[] for the pldo, ftsmps, and boost type regulators.
Port these ranges over to the RPM SMD regulator driver so that we
list the appropriate set of supported voltages on pldos.
Doing this allows us to specify a voltage like 3075000 for l24,
whereas before that wasn't a supported voltage.
Fixes: da65e367b6 ("regulator: Regulator driver for the Qualcomm RPM")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
The continuous mode allows one to declare a PWM regulator without having
to declare the voltage <-> dutycycle association table. It works fine as
long as your voltage(dutycycle) function is linear, but also has the
following constraints:
- dutycycle for min_uV = 0%
- dutycycle for max_uV = 100%
- dutycycle for min_uV < dutycycle for max_uV
While the linearity constraint is acceptable for now, we sometimes need to
restrict of the PWM range (to limit the maximum/minimum voltage for
example) or have a min_uV_dutycycle > max_uV_dutycycle (this could be
tweaked with PWM polarity, but not all PWMs support inverted polarity).
Add the pwm-dutycycle-range and pwm-dutycycle-unit DT properties to define
such constraints. If those properties are not defined, the PWM regulator
use the default pwm-dutycycle-range = <0 100> and
pwm-dutycycle-unit = <100> values (existing behavior).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This fix alters the minimum and maximum BUCK voltage limits for DA9052 and
DA9053. It does so for the following cases:
DA9052
- BUCK3 (MEM)
min: 0.925V -> 0.950V
max: 2.500V -> 2.525V
DA9053
- BUCK3 (MEM)
min: 0.925V -> 0.950V
max: 2.500V -> 2.525V
- BUCK4 (PERI)
min: 0.925V -> 0.950V
max: 2.500V -> 2.525V
The voltage range remains the same, but the limits are shifted by +0.025V.
This change is provided on DA9052:MEM, DA9053:MEM and DA9053:PERI
and is a voltage difference of 0.025V, compared to those measured before
this fix is applied. The patch has the effect of decreasing *all* measured
voltages on those BUCKs when compared against the previously measured
values for the same software voltage request.
For example, with this fix applied for DA9052:MEM, DA9053:MEM and
DA9053:PERI, the following is true.
Because the previous software defined slot 0 as being 0.925V, if a request
for 0.950V was previously sent, the slot 1 voltage would have been used.
This would have corresponded to an actual measured voltage of 0.975V. But,
with this patch fix, and with slot 0 properly aligned to 0.950V, if a
voltage of 0.950V is requested by software, a measured value of 0.950V will
be provided.
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MT6323 is a regulator found on boards based on MediaTek MT7623 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Addition of device tree support for DA9210.
Two files are modified, the driver source file and the binding document.
Updates for the regulator source file include an .of_match_table entry and
node match checking in the probe() function for a compatible da9210 string.
Minor binding documentation changes have been made to the title and the
example.
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This node pointer is returned by of_get_child_by_name() with
refcount incremented in this function. of_node_put() is missing
when exitting this function while invalid device type. Fix it
by move of_get_child_by_name() code after device type check.
Found by Coccinelle.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is only one instance of ab8500_regulator_platform_data, and it's
safe to assume we won't ever merge another one, so it's rather pointless
to pass it through multiple levels of platform data pointers.
This moves the structure and everything referenced by it into the
driver that uses it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pm8x41_hfsmps ranges overlap. The first range is from 375000
to 1562500:
375000 + (95 * 12500) == 1562500
and the second range starts at 1550000. Interestingly, the second
range ends at the correct value when it's set to be the
appropriate start value, 1575000:
1575000 + ((158 - 96) * 25000) == 3125000
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes some of the LDOs and BUCKs voltage range as per
user manual of s2mps15 (REV0.4).
Fixes: 51af206758 ("regulator: s2mps11: Add support for S2MPS15 regulators")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The continuous PWM voltage regulator is caching the voltage value in
the ->volt_uV field. While most of the time this value should reflect the
real voltage, sometime it can be sightly different if the PWM device
rounded the set_duty_cycle request.
Moreover, this value is not valid until someone has modified the regulator
output.
Remove the ->volt_uV field and always rely on the PWM state to calculate
the regulator output.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The ->state field is currently initialized to 0, thus referencing the
voltage selector at index 0, which might not reflect the current
voltage value.
If possible, retrieve the current voltage selector from the PWM state,
else return -EINVAL.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use the atomic API wherever appropriate and get rid of pwm_apply_args()
call (the reference period and polarity are now explicitly set when
calling pwm_apply_state()).
We also make use of the pwm_set_relative_duty_cycle() helper to ease
relative to absolute duty_cycle conversion.
Note that changes introduced by commit fd786fb027 ("regulator: pwm:
Try to avoid voltage error in duty cycle calculation") are no longer
needed because pwm_set_relative_duty_cycle() takes care of all rounding
approximation for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM attached to a PWM regulator device might have been previously
configured by the bootloader.
Make sure the bootloader and linux config are in sync, and adjust the PWM
config if that's not the case.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The original commit adding support for continuous voltage mode didn't
handle the regulator ramp delay properly. It treated the delay as a
fixed delay in uS despite the property being defined as uV / uS. Let's
adjust it. Luckily there appear to be no users of this ramp delay for
PWM regulators (as per grepping through device trees in linuxnext).
Note also that the upper bound of usleep_range probably shouldn't be a
full 1 ms longer than the lower bound since I've seen plenty of hardware
with a ramp rate of ~5000 uS / uV and for small jumps the total delays
are in the tens of uS. 1000 is way too much. We'll try to be dynamic
and use 10%.
NOTE: This commit doesn't add support for regulator-enable-ramp-delay.
That could be done in a future patch when someone has a user of that
featre.
Though this patch is shows as "fixing" a bug, there are no actual known
users of continuous mode PWM regulator w/ ramp delay in mainline and so
this likely won't have any effect on anyone unless they are working
out-of-tree with private patches. For anyone in this state, it is
highly encouraged to also pick Boris Brezillon's WIP patches to get
yourself a reliable and glitch-free regulator.
Fixes: 4773be185a ("regulator: pwm-regulator: Add support for continuous-voltage")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SD4 regulator is not registered with regulator core
framework in probe as there is no support in MAX77620 PMIC,
removing SD4 entry from MAX77620 regulator information list
and checking for valid regulator information data before
configuring FPS source and FPS power up/down period to avoid
NULL pointer exception if regulator not registered with core.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch for adding description for da9212/da9214.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the driver to support Ricoh RN5T567. Support the additional
DCDC and slightly different voltage range of LDORTC1.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The reset value for this register seems broken on certain versions of
tps65218 chip, so make sure the dcdc3 settings is proper. Needed for
proper functionality of rtc+ddr / rtc-only modes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TPS65218 has a pre-defined power-up / power-down sequence which in
a typical application does not need to be changed. However, it is possible
to define custom sequences under I2C control. The power-up sequence is
defined by strobes and delay times. Each output rail is assigned to a
strobe to determine the order in which the rails are enabled.
Every regulator has sequence registers and every regulator has a default
strobe value and gets disabled when a particular power down sequence
occurs.
To keep a regulator on during suspend we write value 0 to strobe so
that the regulator is out of all sequencers and is not impacted by any
power down sequence. Hence saving the default strobe value during probe
so that when we want to regulator to be enabled during suspend we write 0
to strobe and when we want it to get disabled during suspend we write
the default saved strobe value.
This allows platform data to specify which power rails should be on or off
during RTC only suspend. This is necessary to keep DDR state while in RTC
only suspend.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TPS65217 has a pre-defined power-up / power-down sequence which in
a typical application does not need to be changed. However, it is possible
to define custom sequences under I2C control. The power-up sequence is
defined by strobes and delay times. Each output rail is assigned to a
strobe to determine the order in which the rails are enabled.
Every regulator of tps65217 PMIC has sequence registers and every
regulator has a default strobe value and gets disabled when a particular
power down sequence occurs.
To keep a regulator on during suspend we write value 0 to strobe so
that the regulator is out of all sequencers and is not impacted by any
power down sequence. Hence saving the default strobe value during probe
so that when we want to regulator to be enabled during suspend we write 0
to strobe and when we want it to get disabled during suspend we write
the default saved strobe value.
This allows platform data to specify which power rails should be on or off
during RTC only suspend. This is necessary to keep DDR state while in RTC
only suspend.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[Enhanced commit log and added dynamic allocation for strobes]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The voltage switches support mode switching, so add support for
these ops to those types of regulators.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a404741 ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on
some datasheets. Let's rename them to match the datasheets and
also match the RPM based regulator driver which calls these by
their 5vs names (see qcom_smd-regulator.c). There aren't any
users of these regulators so far, so there aren't any concerns of
DT ABI breakage here. While we're here making updates to the
switches, also mandate usage of the OCP irq for these switches
too.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a404741 ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The S4 supply is sometimes called the boost regulator because it
outputs 5V. Typically it's connected to the 5vs1 and 5vs2
switches for use in USB OTG and HDMI applications. Add support
for this regulator which was mistakenly left out from the initial
submission of this driver.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a404741 ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an optional enable GPIO to the pwm-regulator driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setup initial suspend state to mem, if suspend state is defined for
mem state. This makes sure that the regulators are in proper mode
already from boot.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No need to pass _nlr to LP873X_REGULATOR(), use ARRAY_SIZE to calculate it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bypass support was added in commit d38018f201 ("regulator: anatop: Add
bypass support to digital LDOs"). A check for valid voltage selectors was
added in commit da0607c8df ("regulator: anatop: Fail on invalid voltage
selector") but it also discards all regulators that are in bypass mode. Add
check for the bypass setting. Errors below were seen on a Variscite mx6
board.
anatop_regulator 20c8000.anatop:regulator-vddcore@140: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddcore@140 failed with error -22
anatop_regulator 20c8000.anatop:regulator-vddsoc@140: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddsoc@140 failed with error -22
Fixes: da0607c8df ("regulator: anatop: Fail on invalid voltage selector")
Signed-off-by: Mika Båtsman <mbatsman@mvista.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_list_voltage_linear_range in rpm_smps_ldo_ops_fixed is
wrong because it is used for fixed regulator without any linear range.
The rpm_smps_ldo_ops_fixed is used for pm8941_lnldo which has fixed_uV
set and n_voltages = 1. In this case, regulator_list_voltage() can return
rdev->desc->fixed_uV without .list_voltage implementation.
Fixes: 3bfbb4d1a4 ("regulator: qcom_smd: add list_voltage callback")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to list_voltage callback, so that consumers
like mmc core, can get information of supported voltage range.
Without this patch there is no way for mmc core to know this voltage range.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is little obvious use case for a regualtor driver to know if it is
possible to vary voltages at all by itself. If a consumer needs to
limit what voltages it tries to set based on the system configuration
then it will need to enumerate the possible voltages, and without that
even if it is possible to change voltages that doesn't mean that
constraints or other consumers will allow whatever change the driver is
trying to do at a given time. It doesn't even indicate if _set_voltage()
calls will work as noop _set_voltage() calls return success.
There were no users of this API that weren't abusing it and now they're
all gone so remove the API.
Signed-off-by: Mark Brown <broonie@kernel.org>
The TWL6030_FIXED_LDO() macro passes the TWL_FIXED_LDO()
macro an 0x0 instead of a NULL. Changing this to a NULL
fixes the following warnings:
drivers/regulator/twl-regulator.c:1068:1: warning: Using plain integer as NULL pointer
drivers/regulator/twl-regulator.c:1069:1: warning: Using plain integer as NULL pointer
drivers/regulator/twl-regulator.c:1070:1: warning: Using plain integer as NULL pointer
drivers/regulator/twl-regulator.c:1071:1: warning: Using plain integer as NULL pointer
drivers/regulator/twl-regulator.c:1072:1: warning: Using plain integer as NULL pointer
drivers/regulator/twl-regulator.c:1073:1: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
After "regulator: qcom_smd: add list_voltage callback" patch adding
pm8941 lnldo regulators would bug on list_voltages as it is a fixed
regulator without any linear range.
This patch fixes that issue by adding dedicated ops for pm8941 lnldo
without list_voltages callback.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org # v4.6
This patch adds support to list_voltage callback, so that consumers
like mmc core, can get information of supported voltage range.
Without this patch there is no way for mmc core to know this voltage range.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org # v4.6
Adjust the MODULE_DESCRIPTION() text to also include the PFUZE3000
as a supported device.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CONFIG_REGULATOR_PFUZE100 option also supports PFUZE3000, so
mention that in the Kconfig text.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should better not use a global 'struct pfuze_regulator' variable,
as this could cause problems if multiple regulator chips are used.
Place it inside the private struct instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The axp20x pmics have 2 power inputs, one called ACIN which is intended
for to be supplied via a powerbarrel on the board and one called VBUS
which is intended to be supplied via an otg connector.
In the VBUS case the pmic needs to know if the board is supplying power
to the otg connector, because then it should not take any power from
its VBUS pin. The axp209 pmic has a N_VBUSEN input pin via which the
board can signal to the pmic whether the board is supplying power to the
otg connector or not.
On the axp221/axp223 this pin can alternatively be used as an output
which controls an external regulator which (optionally) supplies
power to the otg connector from the board. When the pin is used as
output it is called DRIVEVBUS in the datasheet.
This commit adds support for the DRIVEVBUS pin as an extra pmic
controlled regulator. Since this is optional a new x-powers,drivebus dt
property is added. When this is present the misc-control register is
written to change the N_VBUSEN input pin to DRIVEVBUS output pin mode and
the extra drivebus regulator is registered with the regulator subsystem.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the PWM regulator driver implements the ->enable/disable() hooks
we can remove the pwm_enable() call from pwm_regulator_set_voltage().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to retrieve fixed voltage configure information through
ACPI interface. This is needed for Intel Bay Trail devices, where a
GPIO is used to control the USB vbus.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The X-Powers AXP809 PMIC has a similar set of regulators as the AXP221,
though a few LDOs were removed, and a new switch output added. Like the
AXP221, AXP809 also has DC1SW and DC5LDO, which are internally chained
to DCDC1 and DCDC5, respectively.
Add support for this new variant. Also remove the "axp22x_" prefix from
DC1SW/DC5LDO supply handling code, as the AXP809 uses it as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet:
SLEW Register(Address = 07h)
b7 b6 b5 b4 b3 b2 b1 b0
48mV/us 42mV/us 36mV/us 30mV/us 24mV/us 18mV/us 12mV/us 6mV/us
Current code does not set correct slew rate in some cases:
e.g. Assume ramp_delay is 10000, current code sets slew register to 6mV/us.
Fix the logic to set slew register.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code can set ramp delay to a wrong setting that the return value
from .set_voltage_time_sel is not enough for proper delay.
Fix the logic in .set_ramp_delay and also remove unused ret_val variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BUCKs of mt6397 have auto mode and pwm mode.
User can use regulator interfaces to control modes
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO interface of_get_named_gpio() has implemented the proper
error returns even EPROBE_DEFER and hence caller need not to
implement any workaround for translating the returned error.
Remove the workaround implemented to handle the return of
of_get_named_gpio().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A common simplified DT parsing code for regulators was introduced in
commit a0c7b164ad ("regulator: of: Provide simplified DT parsing
method")
While at it also added RK8XX_DESC and RK8XX_DESC_SWITCH macros for the
regulator_desc struct initialization. This just makes the driver more compact.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators set consists of 2 BUCKs and 2 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components. The ramp delay is configurable
for both BUCKs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just dereference match->of_node once instead of using match->of_node.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stop the palmas regulator driver from imagining that the allocations
will always succeed. Since regulator dt nodes are optional in nature and
can be described in downstream drivers via platform data, continue to
maintain code flow as prior when of node is not found.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Converting dt to platform data logic involves picking up information
that is unique per regulator, however we can improve readability of
the code by allocating and referencing pdata->reg_init[idx] once in
the loop.
While at it, use sizeof(*pointer) when allocating pointer. This allows
for structure name changes with minimal code change.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Converting dt to platform data logic involves picking up information
that is unique per regulator, however we can improve readability of
the code by dereferencing ddata->palmas_matches[idx] once in the loop.
While at it fix reuse of generic palmas_matches common variable
while reporting error for a specific regulator (which may be from
65917/palmas list).
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The enable time for buck regulators was not configured but actually is
essential: consumers, like usb3503, doing hard reset (regulator off/on)
should wait for the regulator to settle.
Configure the enable time according to datasheet.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum supported voltage for ldo_io# is 3.3V, but on cold
boot the selector comes up at 0x1f, which maps to 3.8V.
This causes _regulator_get_voltage() to fail with -EINVAL which
causes regulator registration to fail when constrains are used:
[ 1.467788] vcc-touchscreen: failed to get the current voltage(-22)
[ 1.474209] axp20x-regulator axp20x-regulator: Failed to register ldo_io1
[ 1.483363] axp20x-regulator: probe of axp20x-regulator failed with error -22
This commits makes the axp20x regulator driver accept the 0x1f register
value, fixing this.
The datasheet does not guarantee reliable operation above 3.3V, so on
boards where this regulator is used the regulator-max-microvolt setting
must be 3.3V or less.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO_REG3 descriptor is using linear_ranges.
Add and use proper ops for LDO_REG3.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to set_machine_constraints() in regulator_register(), will
attempt to get the voltage for the regulator. If a regulator is in
bypass will fail to get the voltage (ie. it's bypass voltage) and
hence register the regulator, because the supply for the regulator has
not been resolved yet.
To fix this, add a call to regulator_resolve_supply() before we call
set_machine_constraints(). If the call to regulator_resolve_supply()
fails, rather than returning an error at this point, allow the
registration of the regulator to continue because for some regulators
resolving the supply at this point may not be necessary and it will be
resolved later as more regulators are added. Furthermore, if the supply
is still not resolved for a bypassed regulator, this will be detected
when we attempt to get the voltage for the regulator and an error will
be propagated at this point.
If a bypassed regulator does not have a supply when we attempt to get
the voltage, rather than returing -EINVAL, return -EPROBE_DEFER instead
to allow the registration of the regulator to be deferred and tried
again later.
Please note that regulator_resolve_supply() will call
regulator_dev_lookup() which may acquire the regulator_list_mutex. To
avoid any deadlocks we cannot hold the regulator_list_mutex when calling
regulator_resolve_supply(). Therefore, rather than holding the lock
around a large portion of the registration code, just hold the lock when
aquiring any GPIOs and setting up supplies because these sections may
add entries to the regulator_map_list and regulator_ena_gpio_list,
respectively.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The minium voltage of 1800mV is a copy and paste error from the axp20x
regulator info. The correct minimum voltage for the ldo_io regulators
on the axp22x is 700mV.
Fixes: 1b82b4e4f9 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When commit b554e14506 ("regulator: tps65917/palmas: Add bypass
ops for LDOs with bypass capability") introduced bypass capability
to palmas regulator, it went with the assumption that regulator
regmap helpers just check val against the bypass_mask.
Unfortunately, this ignored the explicit "on" and "off" values when
the register value is masked with bypass_mask in commit ca5d1b3524
("regulator: helpers: Modify helpers enabling multi-bit control").
With the recent commit dd1a571dae ("regulator: helpers: Ensure
bypass register field matches ON value"), this issue gets highlighted
and fails tps65917/palmas based platforms which need regulators/ldos
that have bypass capability.
Introduce the bypass_on value appropriately for tps65917/palmas
regulator.
Fixes: b554e14506 ("regulator: tps65917/palmas: Add bypass ops for LDOs with bypass capability")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current linear voltage range for the LDO4 regulator found in the APX20X
PMICs assumes that the voltage is linear between 2.5 and 3.1V.
However, the PMIC can output up to 3.3V on that regulator by skipping the
2.6V and 2.9V steps.
Fix the ranges to read and set the proper voltages.
Fixes: 13d57e6435 ("regulator: axp20x: Use linear voltage ranges for AXP20X LDO4")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
After removing all uses of the range operations in a recent patch,
we get a warning about the symbol not being referenced anywhere:
drivers/regulator/rk808-regulator.c:306:29: 'rk808_reg_ops_ranges' defined but not used
This removes the now-unused structure along with the
rk808_set_suspend_voltage_range function that is only referenced from
rk808_reg_ops_ranges.
Fixes: afcd666d9d ("regulator: rk808: remove linear range definitions with a single range")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To make the code more compat and centralized, this patch add a
unified function - regulator_ops_is_valid. So we can add
some extra checking code easily later.
Signed-off-by: WEN Pingbo <pingbo.wen@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was using only linear ranges. Now we remove linear range
definitions with a single range. So we have to add an ops struct for
ranges and adjust all other ops functions accordingly.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maxim advertised the ramp rate of the rail with some recommended
design specification like output capacitance of rail should be
2.2uF. This make sure that current change in the rail is within
maximum current limit and hence meet the advertised ramp rate.
If there is variation in design which causes the rail current to
change more that maximum current limit then device applies the
current limit. In this case, ramp rate is different than advertised
ramp rate.
Add device specific settings for ramp rate which need to be configure
on device register when measure ramp rate on platform is deviated from
advertised ramp rate. In this case, all delay time calculation for
voltage change is done with measured ramp rate and device ramp rate
is used for configuring the device register.
If measured ramp rate in the platform is same as advertised ramp rate
then regulator-ramp-delay is used for the device register configuration
and ramp time calculation for voltage change.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When checking bypass state for a regulator, we check to see if any bits
in the bypass mask are set. For most cases this is fine because there is
typically, only a single bit used to determine if the regulator is in
bypass. However, for some regulators, such as LDO6 on AS3722, the bypass
state is indicate by a value rather than a single bit. Therefore, when
checking the bypass state, check that the bypass field matches the ON
value.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The public functions to acquire a regulator, such as regulator_get(),
internally look-up the regulator from the list of regulators that have
been registered with the regulator device class. The registration of
a new regulator with the regulator device class happens before the
regulator has been completely setup. Therefore, it is possible that
the regulator could be acquired before it has been setup successfully.
To avoid this move the device registration of the regulator to the end
of the regulator setup and update the error exit path accordingly.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During the resolution of a regulator's supply, we may attempt to enable
the supply if the regulator itself is already enabled. If enabling the
supply fails, then we will call _regulator_put() for the supply.
However, the pointer to the supply has not been cleared for the
regulator and this will cause a crash if we then unregister the
regulator and attempt to call regulator_put() a second time for the
supply. Fix this by clearing the supply pointer if enabling the supply
after fails when resolving the supply for a regulator.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function regulator_register_resolve_supply() is called from the
context of class_for_each_dev() (during the regulator registration) to
resolve any supplies added. regulator_register_resolve_supply() will
return an error if a regulator's supply cannot be resolved and this will
terminate the loop in class_for_each_dev(). This means that we will not
attempt to resolve any other supplies after one has failed. Hence, this
may delay the resolution of other regulator supplies until the failing
one itself can be resolved.
Rather than terminating the loop early, don't return an error code and
keep attempting to resolve any other supplies for regulators that have
been registered.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are debugfs entries for voltage and current, but not for
the constraint flags. It's useful for debugging to be able to
see what these flags are so this patch adds a new debugfs file.
We can't use debugfs_create_bool for this because the flags are
bitfields, so as this needs a special read callback they have been
collected into a single file that lists all the flags.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tps6524x driver uses spi_dev_get() to take a copy of the SPI device
it uses but has no obvious reason to do so and never calls spi_dev_put()
to release the reference. Fix this to just a straight copy.
Signed-off-by: Mark Brown <broonie@kernel.org>
IC type options 00, 13 and 23 are sharing the same DIE_ID 0.
Let's differentiate between these revisions.
FAN53555UC13X has the ID 0 and REV 0xf, starts at 800mV and
increments in 10mV steps.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
FAN53555BUC18X has the DIE_ID 8, starts at 600mV and
increments in 10mV steps.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
suspend_prepare can be called during regulator init time also, where
the mutex is not locked yet. This causes a false lockdep warning.
To avoid the problem, remove the lockdep assertion from the function
causing the issue. An alternative would be to lock the mutex during
init, but this would cause other problems (some APIs used during init
will attempt to lock the mutex also, causing deadlock.)
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for the Powerventure PV88080 BUCKs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban..opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver did not provide default value for ramp delay for LDOs which lead
to warning in dmesg, e.g. on Odroid XU4:
[ 1.486076] vdd_ldo9: ramp_delay not set
[ 1.506875] vddq_mmc2: ramp_delay not set
[ 1.523766] vdd_ldo15: ramp_delay not set
[ 1.544702] vdd_sd: ramp_delay not set
The datasheet for all the S2MPS1x family is inconsistent here and does
not specify unambiguously the value of ramp delay for LDO. It mentions
30 mV/us in one timing diagram but then omits it completely in LDO
regulator characteristics table (it is specified for bucks).
However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12
mV/us or 24 mV/us.
Without the ramp delay value the consumers do not wait for voltage
settle after changing it. Although the proper value of ramp delay for
LDOs is unknown, it seems safer to use at least some value from
reference kernel than to leave it unset.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I had a thinko in spmi_regulator_select_voltage_same_range() when
converting it to return selectors via the function's return value
instead of by modifying a pointer argument. I only tested
multi-range regulators so this passed through testing. Fix it by
returning the selector here.
Fixes: 1b5b196892 ("regulator: qcom_spmi: Only use selector based regulator ops")
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is harmless but my static checker complains that "tmp" is
uninitialized if lp3972_i2c_read() fails. I have moved the line of code
below the error handling to silence the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is harmless but if lp3971_i2c_read() fails then "tmp" can be
uninitialized. Silence the warning by moving the error handling up a
line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver MAX8973 supports the driver for Maxim PMIC MAX77621.
MAX77621 supports the junction temp warning at 120 degC and
140 degC which is configurable. It generates alert signal when
junction temperature crosses these threshold.
MAX77621 does not support the continuous temp monitoring of
junction temperature. It just report whether junction temperature
crossed the threshold or not.
Add support to
- Configure junction temp warning threshold via DT property
to generate alert when it crosses the threshold.
- Add support to interrupt the host from this device when alert
occurred.
- read the junction temp via thermal framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we acquire a shareable enable GPIO on probe we do so with the
regulator_list_mutex held. However when we release the GPIOs we do this
immediately after dropping the mutex meaning that the list could become
corrupted. Move the release into the locked region to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
device_register() is calling ->get_voltage() as part of it's sysfs attribute
initialization process, and this functions might need to know the regulator
constraints to return a valid value.
This is at least true for the pwm regulator driver (when operating in
continuous mode) which needs to know the minimum and maximum voltage values
to calculate the current voltage:
min_uV + (((max_uV - min_uV) * dutycycle) / 100);
Move device_register() after set_machine_constraints() to make sure those
constraints are correctly initialized when ->get_voltage() is called.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Stephen Barber <smbarber@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a regulator is in bypass mode it is functioning as a switch
returning the voltage set in the regulator will not give the voltage
being output by the regulator as it's just passing through its supply.
This means that when we are getting the voltage from a regulator we
should check to see if it is in bypass mode and if it is we should
report the voltage from the supply rather than that which is set on the
regulator.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
[treding@nvidia.com: return early for bypass mode]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A const pointer to regulator ops is stored in regulator descriptors. The
operations never need to be modified, so define them as const as a hint
to the compiler that they can go into .rodata.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LD06 on the AS3722 power management IC supports a bypass mode. Bypass
is enabled for the LDO by writing the value 0x3F to the voltage select
field in the control register for the LDO. Note that this is the same
register and field that is used to select the voltage as well for the
LDO.
Add support for bypass on LDO6 by specifying the various bypass
parameters for regulator and adding new function pointer tables for the
LDO. Note that the bypass OFF value is the same as the ON value simply
because there is no actual OFF value and bypass will be disabled when
a new voltage is written to the VSEL field.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver's init and exit function don't do anything besides registering
and unregistering the platform driver, so the module_platform_driver()
macro could just be used instead of having separate functions.
Currently the macro is not being used because the driver is initialized at
subsys init call level but this isn't necessary since consumer devices are
defined in the DT as dependencies so there's no need for init calls order.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver's init and exit function don't do anything besides registering
and unregistering the platform driver, so the module_platform_driver()
macro could just be used instead of having separate functions.
Currently the macro is not being used because the driver is initialized at
subsys init call level but this isn't necessary since consumer devices are
defined in the DT as dependencies so there's no need for init calls order.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit <2330b05c095bdeaaf1261c54cd2d4b9127496996> ("regulator: twl: Make
sure we have access to powerbus before trying to write to it")
has implemented the needed logic to correctly access powerbus through i2c,
however it brought a typo when powerbus configuration is restored, which
results in writing to a wrong register. Fix that by providing the correct
register value.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In continuous mode of the PWM regulators, the requested voltage
PWM duty cycle is calculated in terms of 100% scale where entire
range denotes 100%. The calculation for PWM pulse ON time(duty_pulse)
is done as:
duty_cycle = ((requested - minimum) * 100) / voltage_range.
then duty pulse is calculated as
duty_pulse = (pwm_period/100) * duty_cycle
This leads to the calculation error if we have the requested voltage
where accurate pulse time is possible.
For example: Consider following case
voltage range is 800000uV to 1350000uV.
pwm-period = 1550ns (1ns time is 1mV).
Requested 900000uV.
duty_cycle = ((900000uV - 800000uV) * 100)/ 1550000
= 6.45 but we will get 6.
duty_pulse = (1550/100) * 6 = 90 pulse time.
90 pulse time is equivalent to 90mV and this gives us pulse time equivalent
to 890000uV instead of 900000uV.
Proposing the solution in which if requested voltage makes the accurate
duty pulse then there will not be any error. On this case, if
(req_uV - min_uV) * pwm_period is perfect dividable by voltage_range
then get the duty pulse time directly.
duty_pulse = ((900000uV - 800000uV) * 1550)/1550000)
= 100
and this is equivalent to 100mV and so final voltage is
(800000 + 100000) = 900000uV which is same as requested,
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct smasung.com into samsung.com.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
