In patch_alc269(), we initialize the primary capsrc so that the device
works from the beginning. It issues CONNECT_SEL verb no matter which
widget is although some widget (e.g. 0x23) has no connection selection
but a mixer, which requires unmuting instead.
This patch fixes the initialization of capsrc by re-using the code as
a helper function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An Intel board needs a white-list entry to enable PC-beep.
Otherwise the driver misdetects (due to bogus BIOS info) and ignores
the PC-beep on 2.6.35.
Reported-and-tested-by: Leandro Lucarella <luca@llucax.com.ar>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the pending periods are often bogus and take long time until
actually processed, it often results in a high CPU usage of the hd-audio
workq. Overall it's better to have low CPU consumption by avoiding a
too tight loop rather than the wake-up timing accuracy.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix HDA beep frequency on IDT 92HD73xx and 92HD71Bxx codecs.
These codecs use the standard beep frequency calculation although the
datasheet says it's linear frequency.
Other IDT/STAC codecs might have the same problem. They should be
fixed individually later.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Passing IEC 61937 encapsulated compressed audio at bitrates over 6.144
Mbps (i.e. more than a single 2-channel 16-bit 192kHz IEC 60958 link)
over HDMI requires the use of HBR Audio Stream Packets instead of Audio
Sample Packets.
Enable HBR mode when the stream has 8 channels and the Non-PCM bit is
set.
If the audio converter is not connected to any HBR-capable pins, return
-EINVAL in prepare().
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set bit 15 (Stream Type) of HDA Stream Format to 1 (Non-PCM) when IEC958
channel status bit 1 (AES0 & 0x02) is set to 1 (non-audio).
This is a prequisite for HDMI HBR passthrough.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just as with the X301. The X300 does not have a way to do SPDIF either.
It does not have a dock connector, nor does it have the SPDIF through
the headphone jack.
This patch fixes it so X300 does not show SPDIF, since it cannot do it.
To add all Lenovo Thinkpads had different codec subsytem IDs:
X300:
http://launchpadlibrarian.net/34862838/Card0.Codecs.codec.0.txt
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo X301 does not have the ability to connect to a docking
station to use the SPDIF port. It also does not have the ability to do
SPDIF though the headphone jack or Display Port jacks.
This patch fixes it so this is not exposed for the X301 and users do
think it has the ability to do SPDIF.
I tested both headphone & display port jacks and it is not there. I have
tested this patch and it works great.
Also to add the other Thinkpads have different subsystem codec IDs.
Here are examples:
X301:
http://launchpadlibrarian.net/31561902/Card0.Codecs.codec.0.txt
X200:
http://launchpadlibrarian.net/49055036/Card0.Codecs.codec.0.txt
W500:
http://launchpadlibrarian.net/36276057/Card0.Codecs.codec.0.txt
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current ALC259/268/269 parser ignores some pins as unhandled,
but user won't notice what goes wrong. So, added a warning message
for the ignored pins as a hint.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call snd_hda_shutup_pins() for power-saving and reboot-notifier in
patch_conexant.c as well as other codecs. This will reduce the pop
noise in power-save mode.
Reference: bnc#624896
https://bugzilla.novell.com/show_bug.cgi?id=624896
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If BIOS sets up the input pin as VREF 50, use the value as is instead of
overriding forcibly to VREF 80. This fixes the quality of inputs on
some devices like Packard-Bell M5210.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since ALC259/269 use the same parser of ALC268, the pin 0x1b was ignored
as an invalid widget. Just add this NID to handle properly.
This will add the missing mixer controls for some devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make a helper function to parse the digital I/Os of all Realtek codecs
to simplify the code and to ensure the setups.
Also, initialize digital I/O pins properly in init callbacks. Some BIOS
seem to leave pins uninitialized.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some ALC662-compatible codecs like ALC892 may have more than 4
connections for the input source. Use HDA_MAX_CONNECTIONS instead of
the fixed magic number 4.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The non-standard name "iMic" makes PulseAudio ignore the microphone.
BugLink: https://launchpad.net/bugs/605101
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS P5-V provides a SSID that unexpectedly matches with the value
compilant with Realtek's specification. Thus the driver interprets
it badly, resulting in non-working PC beep.
This patch adds a white-list for such a case; a white-list of known
devices with working PC beep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable PC-beep as default for hardwares that aren't compliant with the
SSID value Realtek requires. In such a case, better to enable the beep
to avoid a regression.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We check now the availability of PC beep and skip the build of beep
mixers, but the driver still registers the input device. This should
be checked as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The behavior of Nvidia HDMI codec regarding the pin-detection unsol events
is based on the old HD-audio spec, i.e. PD bit indicates only the update
and doesn't show the current state. Since the current code assumes the
new behavior, the pin-detection doesn't work relialby with these h/w.
This patch adds a flag for indicating the old spec, and fixes the issue
by checking the pin-detection explicitly for such hardware.
Tested-by: Wei Ni <wni@nvidia.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit afbd9b8448
ALSA: hda - Limit the amp value to write
introduced a regression for codec setups with amp offsets like IDT/STAC
codecs. The limit value should be a raw value without offset calculation.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a follow on patch adds support for AMD based Lenovo G series
machines, such as the Lenovo G555.
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some VAIO models with ALC275 have dual ADCs for both internal and external
mics, and the driver needs to switch one of them appropriately.
This patch adds a basic support for this functionality, dynamic switching
between two ADCs per jack plug state.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correctly configure bidirectional pins when resuming; do not power down
widgets when they are needed for Smart5.1 output; and on 3-jack boards,
create the streams and controls needed for six channels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Viliam Kubis <viliam.kubis@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the amp max value at put callbacks and set the upper limit
so that the driver won't write any invalid value over the defined
range.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the beep mixer controls to Conexant codecs.
They simply control the digital beep generator widget.
For cx5047, I couldn't find any beep generator, so it's not implemented
there.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many codecs now clear the pin controls at suspend via snd_hda_shutup_pins()
for reducing the click noise at power-off. But this leaves some pins
uninitialized, and they'll be never recovered after resume.
This patch adds the proper recovery of cleared pin controls on resume.
Also it adds a check of bus->shutdown so that pins won't be cleared at
module unloading.
Reference: Kernel bug 16339
http://bugzilla.kernel.org/show_bug.cgi?id=16339
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the PCI SSID gives an overriding SKU assno, PC-beep bit isn't
detected (since it's located over 16bit), resulting in no PC beep.
Also, many devices seem ignoring the requirement by Realtek's spec
for SSID numbers, and it also confuses the PC beep detection.
This patch assumes the PC beep is available on every machine with
PCI SSID override. It's a regression fix from 2.6.34.
Reference: Kernel bug 16251
http://bugzilla.kernel.org/show_bug.cgi?id=16251
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugs.launchpad.net/bugs/463178
Set Macbook 5,2 (106b:4a00) hardware to use ALC885_MB5
Cc: <stable@kernel.org>
Signed-off-by: Luke Yelavich <luke.yelavich@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the following compile warning. kctl should be NULL-initialized.
sound/pci/hda/patch_realtek.c: In function ‘alc_build_controls’:
sound/pci/hda/patch_realtek.c:2550:23: warning: ‘kctl’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo IdeaPad Y430 has an additional subwoofer connected at pin 0x1b,
which isn't muted when headphone is plugged in. This adds additional
support to the extra subwoofer via new ideapad model.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The line-in input is 0x7 not 0x2 for MacBook (Pro) 5,1 / 5,2 models
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With multiple codec configurations, some codec might have no ADC, thus
it keeps spec->adc_nids = NULL. This causes an Oops in alc_build_controls().
Reference: kernel bug #16156https://bugzilla.kernel.org/show_bug.cgi?id=16156
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add's the iMac7,1 SSID entry to
patch_realtek.c which adds sound support.
bug entry:
https://bugs.launchpad.net/mactel-support/+bug/360866
Note:I do not have this machine on hand only
codec#0 file for the machine so please
test if you have the appropriate equipment.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add's the MacBookAir1,1 SSID entry to
patch_realtek.c which adds sound support.
bug entry:
https://bugs.launchpad.net/mactel-support/+bug/268301
Note:I do not have this machine on hand only
codec#0 file for the machine so please
test if you have the appropriate equipment.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds the SSID number to snd_pci_quirk for the
MacBookAir2,1 taken from codec#0 at:
http://launchpadlibrarian.net/49455483/Card0.Codecs.codec.0.txt
keep in mind I do not have one of these machines on hand
so please if you do have this machine please test for me..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes thinko introduced in "last minutes" before commiting
of the last wallclk patch.
It also fixes the condition checking if the first period after last
wallclk update is processed. There is a little rounding error in
period_wallclk.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Initialize prev_ctl properly before reference:
sound/pci/asihpi/asihpi.c: In function ‘snd_card_asihpi_mixer_new’:
sound/pci/asihpi/asihpi.c:2568:30: warning: ‘prev_ctl.dst_node_index’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
