The LED also indicates the status of the tablet. Don't turn it off.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The LED luminance level is normally lower when no button is pressed.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the TSC-40 serial touchscreen driver and should be
compatible with TSC-10 and TSC-25.
The driver was written by Linutronix on behalf of Bachmann electronic GmbH.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use the of_property_read_u32() helper function to retrieve u32 values
from the device tree. Also do not pass the len parameter to
of_get_property if it isn't checked afterwards.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since touchscreen driver does not handle any events to be sent to the
device we can close serio port first and then unregister the input device.
Tested-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of having one large switch based on product ID use pointer to
function actually doing protocol decoding.
Tested-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add multi touch support for PenMount 6250 touch controller.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MSB and LSB of the XY axis value are switched according to the PenMount 9000 protocol. The driver name is also changed from penmountlpc, since it is not for LPC interface at all.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This essentially reverts commit f81bc788ff.
With recent work on elantech driver, I believe we now have complete support
for all elantech touchpads. So remove this hack.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
V2 hardware has many variants. This patch adddresses two issues:
- some model also has debounce packets, but with a different signature
than v3. Now we just check debounce for all v2 hardware.
- due to different scanning methods the hardware uses, x and y ranges have
to be calculated differently. And for some specific versions, we can just
see them as custom-made, so set {x, y} the same values as Windows driver
does.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Tested-by: Richard Schütz <r.schtz@t-online.de>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
v4 hardware is a true multitouch capable touchpad (up to 5 fingers).
The packet format is quite complex, please see protocol document for
reference.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
v3 hardware's packet format is almost identical to v2 (one/three finger touch),
except when sensing two finger touch, the hardware sends 12 bytes of data.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For v2 hardware, there is no real parity check, but we can still check
some constant bits for data integrity.
Also rename elantech_check_parity_v1 to elantech_packet_check_v1 to make
these packet checking function names consistent.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Don't try to be too clever and remove ETP_EDGE_FUZZ_V2. X, Y ranges
should be just the raw resolution of the device. Otherwise, they can
cause underflow on the Y axis.
Suggested-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With newer hardware, the touchpad provides range info.
Let's use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For two finger touches the coordinate of each finger gets reported
separately but with reduced resolution.
With this change, we now have the same range for ST and MT data and
scale MT data because it has lower resolution to match ST.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix warning from Geert's build summary emails by changing "if" to
"ifdef". Thsi should fix the following:
drivers/input/misc/twl6040-vibra.c:231:5: warning: "CONFIG_PM_SLEEP" is not defined
Builds cleanly with CONFIG_PM_SLEEP enabled or disabled.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Take spinlock when entering ISR and timer routine to ensure that we do not
race while enabling/disabling FIFO interrupts.
Also we do not need to take teh spinlock in tegra_kbc_startremove() since
interrupt is completely disabled.
Tested-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For wakeup to be reliable, kbc needs to be in interrupt mode before suspend.
Created common routine to control the FIFO interrupt.
Added synchronization to ensure orderly suspend.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
WARNING: drivers/input/keyboard/built-in.o(.text+0xb55b): Section mismatch in reference from the function tc3589x_keypad_open() to the function .devinit.text:tc3589x_keypad_init_key_hardware()
The function tc3589x_keypad_open() references
the function __devinit tc3589x_keypad_init_key_hardware().
This is often because tc3589x_keypad_open lacks a __devinit
annotation or the annotation of tc3589x_keypad_init_key_hardware is wrong.
Signed-off-by: Harvey Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This commit enables control of the LEDs and OLED displays found on the
Wacom Intuos4 M, L, and XL. For this purpose, a new "wacom_led" attribute
group is added to the sysfs entry of the USB device.
This "wacom_led" group only shows up when the correct device (M, L, or XL)
is detected. The attributes are described in
Documentation/ABI/testing/sysfs-wacom
Signed-off-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will ensure that the device delivers input events only when there
are users.
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of using hard IRQ and workqueue solution switch to using threaded
interrupt handler to simplify the code and locking rules.
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad714x - read the interrupt status registers in a row
Input: ad714x - use DMA-safe buffers for spi_write()
Input: ad714x - fix endianness issues
Input: ad714xx-spi - force SPI bus into the default 8-bit mode
Input: ep93xx_keypad - add missing include of linux/module.h
Input: tnetv107x-ts - add missing include of linux/module.h
Input: max11801_ts - correct license statement
Input: atmel_mxt_ts - report pressure information from the driver
Input: bcm5974 - Add support for newer MacBookPro8,2
Input: wacom - report id 3 returns 4 bytes of data
Input: wacom - add WAC_MSG_RETRIES define
Input: wacom - add support for the Wacom Bamboo Pen (CTL-660/K)
Input: tegra-kbc - correct call to input_free_device
Input: mpu3050 - correct call to input_free_device
Input: bcm5974 - add support for touchpads found in MacBookAir4,2
Input: mma8450 - fix module device table type
Input: remove CLOCK_TICK_RATE from analog joystick driver
Change the placement of __init and __exit annotations to be consistent
with the rest of the drivers.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics image sensor touchpads track up to 5 fingers, but only report 2.
They use a special "TYPE=2" (AGM-CONTACT) packet type that reports
the number of tracked fingers and which finger is reported in the SGM
and AGM packets.
With this new packet type, it is possible to tell userspace when 4 or 5
fingers are touching.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
"4-finger scroll" is a gesture supported by some applications and
operating systems.
"Resting thumb" is when a clickpad user rests a finger (e.g., a
thumb), in a "click zone" (typically the bottom of the touchpad) in
anticipation of click+move=select gestures.
Thus, "4-finger scroll + resting thumb" is a 5-finger gesture.
To allow userspace to detect this gesture, we send BTN_TOOL_QUINTTAP.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics image sensor touchpads track 5 fingers, but only report 2.
This patch attempts to deal with some idiosyncrasies of these touchpads:
* When there are 3 or more fingers, only two are reported.
* The touchpad tracks the 5 fingers in slot[0] through slot[4].
* It always reports the lowest and highest valid slots in SGM and AGM
packets, respectively.
* The number of fingers is only reported in the SGM packet. However,
the number of fingers can change either before or after an AGM
packet.
* Thus, if an SGM reports a different number of fingers than the last
SGM, it is impossible to tell whether the intervening AGM corresponds
to the old number of fingers or the new number of fingers.
* For example, when going from 2->3 fingers, it is not possible to tell
whether tell AGM contains slot[1] (old 2nd finger) or slot[2] (new
3rd finger).
* When fingers are added one at at time, from 1->2->3, it is possible to
track which slots are contained in the SGM and AGM packets:
1 finger: SGM = slot[0], no AGM
2 fingers: SGM = slot[0], AGM = slot[1]
3 fingers: SGM = slot[0], AGM = slot[2]
* It is also possible to track which slot is contained in the SGM when 1
of 2 fingers is removed. This is because the touchpad sends a special
(0,0,0) AGM packet whenever all fingers are removed except slot[0]:
Last AGM == (0,0,0): SGM contains slot[1]
Else: SGM contains slot[0]
* However, once there are 3 fingers, if exactly 1 finger is removed, it
is impossible to tell which 2 slots are contained in SGM and AGM.
The (SGM,AGM) could be (0,1), (0,2), or (1,2). There is no way to know.
* Similarly, if two fingers are simultaneously removed (3->1), then it
is only possible to know if SGM still contains slot[0].
* Since it is not possible to reliably track which slot is being
reported, we invalidate the tracking_id every time the number of
fingers changes until this ambiguity is resolved when:
a) All fingers are removed.
b) 4 or 5 fingers are touched, generates an AGM-CONTACT packet.
c) All fingers are removed except slot[0]. In this special case, the
ambiguity is resolved since by the (0,0,0) AGM packet.
Behavior of the driver:
When 2 or more fingers are present on the touchpad, the kernel reports
up to two MT-B slots containing the position data for two of the fingers
reported by the touchpad. If the identity of a finger cannot be tracked
when the number-of-fingers changes, the corresponding MT-B slot will be
invalidated (track_id set to -1), and a new track_id will be assigned in
a subsequent input event report.
The driver always reports the total number of fingers using one of the
EV_KEY/BTN_TOOL_*TAP events. This could differ from the number of valid
MT-B slots for two reasons:
a) There are more than 2 fingers on the pad.
b) During ambiguous number-of-fingers transitions, the correct track_id
for one or both of the slots cannot be determined, so the slots are
invalidated.
Thus, this is a hybrid singletouch/MT-B scheme. Userspace can detect
this behavior by noting that the driver supports more EV_KEY/BTN_TOOL_*TAP
events than its maximum EV_ABS/ABS_MT_SLOT.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A Synaptics image sensor tracks 5 fingers, but can only report 2.
The algorithm for choosing which 2 fingers to report and in which packet:
Touchpad maintains 5 slots, numbered 0 to 4
Initially all slots are empty
As new fingers are detected, assign them to the lowest available slots
The touchpad always reports:
SGM: lowest numbered non-empty slot
AGM: highest numbered non-empty slot, if there is one
In addition, these touchpads have a special AGM packet type which reports
the number of fingers currently being tracked, and which finger is in
each of the two slots. Unfortunately, these "TYPE=2" packets are only used
when more than 3 fingers are being tracked. When less than 4 fingers
are present, the 'w' value must be used to track how many fingers are
present, and knowing which fingers are being reported is much more
difficult, if not impossible.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics makes (at least) two kinds of touchpad sensors:
* Older pads use a profile sensor that could only infer the location
of individual fingers based on the projection of their profiles
onto row and column sensors.
* Newer pads use an image sensor that can track true finger position
using a two-dimensional sensor grid.
Both sensor types support an "Advanced Gesture Mode":
When multiple fingers are detected, the touchpad sends alternating
"Advanced Gesture Mode" (AGM) and "Simple Gesture Mode" (SGM)
packets.
The AGM packets have w=2, and contain reduced resolution finger data
The SGM packets have w={0,1} and contain full resolution finger data
Profile sensors try to report the "upper" (larger y value) finger in
the SGM packet, and the lower (smaller y value) in the AGM packet.
However, due to the nature of the profile sensor, they easily get
confused when fingers cross, and can start reporting the x-coordinate
of one with the y-coordinate of the other. Thus, for profile
sensors, "semi-mt" was created, which reports a "bounding box"
created by pairing min and max coordinates of the two pairs of
reported fingers.
Image sensors can report the actual coordinates of two of the fingers
present. This patch detects if the touchpad is an image sensor and
reports finger data using the MT-B protocol.
NOTE: This patch only adds partial support for 2-finger gestures.
The proper interpretation of the slot contents when more than
two fingers are present is left to later patches. Also,
handling of 'number of fingers' transitions is incomplete.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When a Synaptics touchpad is in "AGM" mode, and multiple fingers are
detected, the touchpad sends alternating "Advanced Gesture Mode" (AGM) and
"Simple Gesture Mode" (SGM) packets.
The AGM packets have w=2, and contain reduced resolution finger data.
The SGM packets have w={0,1} and contain full resolution finger data.
Refactor the parsing of agm packets to its own function, and rename the
synaptics_data.mt field to .agm to indicate that it contains the contents of
the last agm packet.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics touchpads report increasing y from bottom to top.
This is inverted from normal userspace "top of screen is 0" coordinates.
Thus, the kernel driver reports inverted y coordinates to userspace.
This patch refactors this inversion.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since touchscreen driver does not handle any events to be sent to the
device we can close serio port first and then unregister the input device.
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Implement open() and close() methods for the input device so that we
do not start the device unless there are users listening to the events.
Acked-by: Chris Bagwell <chris@cnpbagwell.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The interrupt status registers should be read in row to avoid invalid data.
Alter "read" method for both bus options to allow reading several registers
in a row and make sure we read interrupt status registers properly.
Read sequence saves 50% of bus transactions compared to single register
reads. So use it also for the result registers, which are also located
in a row.
Also update copyright notice.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
spi_write() requires use of DMA-safe (cacheline aligned) buffers.
Also use the same buffers when reading data since to avoid extra
locking and potential memory allocation in spi_write_then_read().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow driver to be used on Big Endian boxes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ep93xx_keypad.c uses interfaces from linux/module.h,
so it should include that file. This patch fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
tnetv107x-ts.c uses interfaces from linux/module.h,
so it should include that file. This patch fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The original license statement was confusing since it was unclear if
the license was pure GPLv2 or GPLv2+ and did not match the license
of the driver max11801_ts was derived from. The license is GPLv2+.
Signed-off-by: Jiejing Zhang <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Atmel mxt1386 touch controller has the touch pressure information so
let's report it to the user space.
[dtor@mail.ru: added ABS_RESSURE reporting for ST emulation.]
Signed-off-by: Yufeng Shen <miletus@chromium.org>
Acked-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New MacBook Pro devices reporting product name MacBookPro8,2 come with
newer/higher resolution touchpads than others with the same product
name with USB ID 05ac:0252. This patch adds support for these devices.
Signed-off-by: Andrew Drake <adrake@adrake.org>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
