ide_start_power_step() and set_using_dma() were missing ->dma_off_quietly
call (comment in probe_hwif() states that DMA should be always cleared before
tuning is attempted). Fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove code enabling IORDY and prefetch from config_chipset_for_dma(),
as the comment states it has no real effect because these settings are
overriden when the PIO mode is set (and for this driver ->autotune == 1
so PIO mode is always programmed)
* use ide_tune_dma() in pdcnew_config_drive_xfer_rate() and remove no longer
needed config_chipset_for_dma()
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_tune_dma() in ali15x3_config_drive_for_dma() and remove all the open
coded DMA tuning code and also config_chipset_for_dma(). Set ->atapi_dma flag
correctly in init_hwif_common_ali15x3() so ide_tune_dma() can take care of
checking if ATAPI DMA is allowed and remove open coded ATAPI DMA check from
ali15x3_config_drive_for_dma().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to program PIO5 by config_art_rwp_pio() could result in incorrect PIO
timings being programmed and possibly the data corruption (for < ATA100
family chipsets PIO0 timings were used, for ATA100 and ATA100a - the random
content of test1 variable was used, for ATA133 - MWDMA0 timings were used)
* BUG() in sis5513_tune_chipset() if somebody tries to force unsupported PIO5,
also cleanup this function a bit while at it
* add comment about PIO0 timings for < ATA100 family chipsets
* remove open-coded best PIO mode selection from config_art_rwp_pio(),
it contained numerous bugs:
- it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
before using them
- it tried to found out maximum PIO mode basing on minimum IORDY cycle time
(moreover wrong cycle times were used for PIO1/5)
- it was overriding PIO blacklist and conservative PIO "downgrade" done
by ide_get_best_pio_mode()
* use sis5513_tune_drive() instead of config_art_rwp_pio()
in sis5513_config_xfer_rate() so the correct PIO mode is also set
on drive even if the device is not IORDY/DMA capable
* config_art_rwp_pio() was always setting the best possible mode and not
the wanted one - fix it and move ide_get_best_pio_mode() call to
config_chipset_for_pio()
* don't use ide_find_best_mode() in config_chipset_for_pio(), it was being
overriden by config_art_rwp_pio() for the host timings anyway + we need to
set the same PIO mode on the device and the host
* pass correct "pio" argument (255 instead of 5) to sis5513_tune_drive() call
in sis5513_config_xfer_rate() so the best PIO mode is set on the drive
and not PIO4
* rename sis5513_tune_drive() to sis5513_tuneproc()
and config_chipset_for_pio() to sis5513_tune_driver()
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to program PIO5 by svwks_tune_chipset() could result in incorrect PIO
timings being programmed and possibly the data corruption (it seems that
the minimum possible values were used but I lack the datasheets to be sure)
* select best PIO mode in svwks_tune_drive() and not in svwks_tune_chipset()
when doing PIO autotuning (pio == 255)
* don't try to tune PIO in config_chipset_for_dma() as ide_dma_enable() could
return 1 if DMA was previously enabled (svwks_config_drive_xfer_rate()
takes care of PIO tuning if no suitable DMA mode is found)
* remove config_chipset_for_pio() and use svwks_tune_drive() instead,
config_chipset_for_pio() contained numerous bugs when selecting PIO mode
(luckily it was only used for devices limited to PIO by capabilities/BIOS):
- it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
before using them
- it tried to found out maximum PIO mode basing on minimum IORDY cycle time
(moreover wrong cycle times were used for PIO0/1/5)
- it was overriding PIO blacklist and conservative PIO "downgrade" done
by ide_get_best_pio_mode()
- if the max drive PIO was PIO5 then XFER_PIO_0/XFER_PIO_SLOW was selected
(XFER_PIO_SLOW is not supported by svwks_tune_chipset() so the result
was the same as if using XFER_PIO_5 => wrong PIO timings were set)
- it was overriding drive->current_speed
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch is based on the documentation (I would like to thank Promise
for it) and also partially on the older vendor driver.
Rewrite mode programming code:
* disable 66MHz clock in pdc202xx_tune_chipset() so it is correctly disabled
even if both devices on the channel are not DMA capable and after reset
* enable/disable IORDY and PREFETCH bits in pdc202xx_tune_chipset()
as they need to be setup correctly also for PIO only devices, plus IORDY
wasn't disabled for non-IORDY devices and PREFETCH wasn't disabled for
ATAPI devices
* remove dead code for setting SYNC_ERDDY_EN bits from config_chipset_for_dma()
(driver sets ->autotune to 1 so PIO modes are always programmed => lower
nibble of register A never equals 4 => "chipset_is_set" is always true)
* enable PIO mode programming for all ATAPI devices
(it was limited to ->media == ide_cdrom devices)
* remove extra reads of registers A/B/C, don't read register D et all
* do clearing / programming of registers A/B/C in one go
(gets rid of extra PCI config space read/write cycle)
* set initial values of drive_conf/AP/BP/CP variables to zero
(paranoia for the case when PCI reads fail)
* remove XFER_UDMA6 to XFER_UDMA5 remapping case - it can't happen
(ide_rate_filter() takes care of it)
* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)
* fix bitmasks for clearing bits of register B:
- when programming DMA mode bit 0x10 of register B was cleared which
resulted in overclocked PIO timing setting (iff PIO0 was used)
- when programming PIO mode bits 0x18 weren't cleared so suboptimal
timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)
* add FIXME comment about missing locking for 66MHz clock register
Also while at it:
* remove unused defines
* do a few cosmetic / CodingStyle fixes
* bump driver version
v2:
* in pdc202xx_tune_chipset() the old content of drive configuration
registers is used only by the debugging code so cover "drive_conf"
PCI registers read by #if PDC202XX_DEBUG_DRIVE_INFO
(Noticed by Sergei Shtylyov)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add devres ecardm_iomap() and ecardm_iounmap() for Acorn expansion
cards. Convert all expansion card drivers to use them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having every driver fiddle about setting its private
IRQ operations and data, provide a helper function to contain
this functionality in one place.
Arrange to remove the driver-private IRQ operations and data when
the device is removed from the driver, and remove the driver
private code to do this.
This fixes potential problems caused by drivers forgetting to
remove these hooks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: fix PIO setup on resume for ATAPI devices
ide: legacy PCI bus order probing fixes
ide: add ide_proc_register_port()
ide: add "initializing" argument to ide_register_hw()
ide: cable detection fixes (take 2)
ide: move IDE settings handling to ide-proc.c
ide: split off ioctl handling from IDE settings (v2)
ide: make /proc/ide/ optional
ide: add ide_tune_dma() helper
ide: rework the code for selecting the best DMA transfer mode (v3)
ide: fix UDMA/MWDMA/SWDMA masks (v3)
IDE PCI host drivers should register themselves with IDE core only when
IDE driver is built-in, otherwise (IDE driver is modular and thus IDE PCI
host drivers are also modular) the code has no effect and just complicates
the probing.
Fix it by adding new config option CONFIG_IDEPCI_PCIBUS (defined only when
needed and invisible to the user) and covering by #ifdef/#endif the code
in question. It turned out that "ide=reverse" was silently accepted but did
nothing in case when IDE driver was modular, this is fixed now.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* create_proc_ide_interfaces() tries to add /proc entries for every probed
and initialized IDE port, replace it by ide_proc_register_port() which does
it only for the given port (also rename destroy_proc_ide_interface() to
ide_proc_unregister_port() for consistency)
* convert {create,destroy}_proc_ide_interface[s]() users to use new functions
* pmac driver depended on proc_ide_create() to add /proc port entries, fix it
* au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic
driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them
* there is now no need to add /proc entries for IDE ports in proc_ide_create()
so don't do it
* proc_ide_create() needs now to be called before drivers are probed - fix it,
while at it make proc_ide_create() create /proc "ide" directory
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add "initializing" argument to ide_register_hw() and use it instead of ide.c
wide variable of the same name. Update all users of ide_register_hw()
accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...
* print user-friendly warning about limiting the maximum transfer speed
to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
also while at it cleanup eighty_ninty_three() a bit
* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
- bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
(please see FIXME comment in eighty_ninty_three() for more details)
- CONFIG_IDEDMA_IVB=y/n cases were interchanged
- check for SATA devices was missing
* remove private cable warnings from pdc_202xx{old,new} drivers now that core
code provides this functionality (plus, in pdc202xx_new case the test could
give false warnings for ATAPI devices because pdc202xx_new driver doesn't
even support ATAPI DMA)
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* move
__ide_add_setting()
ide_add_setting()
__ide_remove_setting()
auto_remove_settings()
ide_find_setting_by_name()
ide_read_setting()
ide_write_setting()
set_xfer_rate()
ide_add_generic_settings()
ide_register_subdriver()
ide_unregister_subdriver()
from ide.c to ide-proc.c
* set_{io_32bit,pio_mode,using_dma}() cannot be marked static now, fix it
* rename ide_[un]register_subdriver() to ide_proc_[un]register_driver(),
update device drivers to use new names
* add CONFIG_IDE_PROC_FS=n versions of ide_proc_[un]register_driver()
and ide_add_generic_settings()
* make ide_find_setting_by_name(), ide_{read,write}_setting()
and ide_{add,remove}_proc_entries() static
* cover IDE settings code in device drivers with CONFIG_IDE_PROC_FS #ifdef,
also while at it cover with CONFIG_IDE_PROC_FS #ifdef ide_driver_t.proc
* remove bogus comment from ide.h
* cover with CONFIG_IDE_PROC_FS #ifdef .proc and .settings in ide_drive_t
Besides saner code this patch results in the IDE core smaller by ~2 kB
(on x86-32) and IDE disk driver by ~1 kB (ditto) when CONFIG_IDE_PROC_FS=n.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* do write permission and min/max checks in ide_procset_t functions
* ide-disk.c: drive->id is always available so cleanup "multcount" setting
accordingly
* ide-disk.c: "address" setting was incorrectly defined as type TYPE_INTA,
fix it by using type TYPE_BYTE and updating ide_drive_t->adressing field,
the bug didn't trigger because this IDE setting uses custom ->set function
* ide.c: add set_ksettings() for handling HDIO_SET_KEEPSETTINGS ioctl
* ide.c: add set_unmaskirq() for handling HDIO_SET_UNMASKINTR ioctl
* handle ioctls directly in generic_ide_ioclt() and idedisk_ioctl()
instead of using IDE settings to deal with them
* remove no longer needed ide_find_setting_by_ioctl() and {read,write}_ioctl
fields from ide_settings_t, also remove now unused TYPE_INTA handling
v2:
* add missing EXPORT_SYMBOL_GPL(ide_setting_sem) needed now for ide-disk
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All important information/features should be already available through
sysfs and ioctl interfaces.
Add CONFIG_IDE_PROC_FS (CONFIG_SCSI_PROC_FS rip-off) config option,
disabling it makes IDE driver ~5 kB smaller (on x86-32).
While at it add CONFIG_PROC_FS=n versions of proc_ide_{create,destroy}()
and remove no longer needed #ifdefs.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After reworking the code responsible for selecting the best DMA
transfer mode it is now possible to add generic ide_tune_dma() helper.
Convert some IDE PCI host drivers to use it (the ones left need more work).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.
* add ide_hwif_t.udma_filter hook for filtering UDMA mask
(use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
(loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()
v2:
* rename ->filter_udma_mask to ->udma_filter
[ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
originated transfer mode change requests when 100MHz clock is used)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* use 0x00 instead of 0x80 to disable ->{ultra,mwdma,swdma}_mask
* add udma_mask field to ide_pci_device_t and use it to initialize
->ultra_mask in aec62xx, cmd64x, pdc202xx_{new,old} and piix drivers
* fix UDMA masks to match with chipset specific *_ratemask()
(alim15x3, hpt366, serverworks and siimage drivers need UDMA mask
filtering method - done in the next patch)
v2:
* piix: fix cable detection for 82801AA_1 and 82372FB_1
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* cmd64x: use hwif->cds->udma_mask
[ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* aec62xx: fix newly introduced bug - check DMA status not command register
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
v3:
* piix: use hwif->cds->udma_mask
[ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Without the following patch, the kernel does not automatically detect
2GB CompactFlash cards from Transcend.
Signed-off-by: Fabrice Aeschbacher <fabrice.aeschbacher@siemens.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
HPT36x chip don't seem to have the channel enable bits, so prevent the IDE core
from checking them...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Michal Kepien <michal.kepien@poczta.onet.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* fix ->speedproc to set the drive speed
* this driver doesn't support SWDMA so use the correct ->swdma_mask
* BUG() if an unsupported mode is passed to ->speedproc
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This driver doesn't support SWDMA so use the correct ->swdma_mask.
While at it:
* no need to call config_chipset_for_pio() in config_chipset_for_dma(),
if DMA is not available config_chipset_for_pio() will be called
by siimage_config_drive_for_dma() and if DMA is available
config_siimage_chipset_for_pio() will be called by siimage_tune_chipset()
* remove needless config_chipset_for_pio() wrapper
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to setup PIO5 by it821x_tuneproc() could result in incorrect PIO timings
+ incorrect base clock being set for controller in the passthrough mode
* move code limiting max PIO according to the pair device capabilities from
config_it821x_chipset_for_pio() to it821x_tuneproc() so the check is also
applied for mode change requests coming through ->tuneproc and ->speedproc
interfaces
* set device speed in it821x_tuneproc()
* in it821x_tune_chipset() call it821x_tuneproc() also if the controller is
in the smart mode (so the check for pair device max PIO is done)
* rename it821x_tuneproc() to it821x_tune_pio(), then add it821x_tuneproc()
wrapper which does the max PIO mode check; it worked by the pure luck
previously, pio[4] and pio_want[4] arrays were used with index == 255
so random PIO timings and base clock were set for the controller in the
passthrough mode, thankfully PIO timings and base clock were corrected
later by config_it821x_chipset_for_pio() call (but it was not called for
PIO-only devices during resume and for user requested PIO autotuning)
* remove config_it821x_chipset_for_pio() call from config_chipset_for_dma()
as the driver sets ->autotune to 1 and ->tuneproc does the proper job now
* convert the last user of config_it821x_chipset_for_pio() to use
it821x_tuneproc(drive, 255) and remove no longer needed function
While at it:
* fix few comments
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Teach the driver's tuneproc() method to do PIO auto-runing properly since it
treated 5 instead of 255 as auto-tune request, and also passed the mode limit
of PIO5 to ide_get_best_pio_mode() despite supporting up to PIO4 only.
While at it, also:
- remove the driver's wrong claim about supporting SWDMA modes;
- stop hooking ide_dma_timeout() method as the handler clearly doesn't fit for
the task...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fold the parts of the ide_dma_end() methods identical to __ide_dma_end() into a
mere call to it.
Start using faster versions of the ide_dma_end() and ide_dma_test_irq() methods
for the PCI0646U and newer chips that have the duplicate interrupt status bits
in the I/O mapped MRDMODE register, determing what methods to use at the driver
load time. Do some cleanup/renaming in the "old" ide_dma_test_irq() method too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix several issues with the driver's procfs output:
- when testing if channel is enabled, the code looks at the "simplex" bits, not
at the real enable bits -- add #define for the primary channel enable bit;
- UltraDMA modes 0, 1, 3 for slave drive reported incorrectly due to using the
master drive's clock cycle resolution bit.
While at it, also perform the following cleanups:
- don't print extra newline before the first controller's dump;
- correct the chipset names (from CMDxxx to PCI-xxx)
- don't read from the registers which aren't used for dump;
- better align the table column sizes;
- rework UltraDMA mode dump code;
- remove PIO mode dump code that has never been finished;
- remove the duplicate interrupt status (the MRDMODE register bits mirror those
those in the CFR and ARTTIM23 registers) and fold the dump into single line;
- correct the style of the ?: operators...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE core looks at the wrong bit when checking if the secondary channel is
enabled on PCI0646 -- CNTRL register bit 7 is read-ahead disable, bit 3 is the
correct one.
Starting with PCI0646U chip, the primary channel can also be enabled/disabled --
so, add 'enablebits' initializers to each 'ide_pci_device_t' structure, handling
the original PCI0646 via adding the init_setup() method and clearing the 'reg'
field there if necessary...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think). In order to do it, a number of changes was necessary:
- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
total/active times instead of the clock counts, and convert them into the
active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
quantize_timing() to also move;
- contrarywise, move all the code handling the address setup timing into
cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;
- remove from the speedproc() method the bogus code pretending to set the DMA
timings by twiddling bits in the BMIDE status register, handle setting MWDMA
by just calling program_cycle_times(); while at it, improve the style of that
whole switch statement;
- stop fiddling with the DMA capable bits in the speedproc() method -- they do
not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;
- don't set hwif->swdma_mask in the init_hwif() method anymore.
In addition to those changes, do the following:
- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
status bit, eliminate local_irq_{save|restore}() around this code as there's
*no* actual race with the interrupt handler, and move cmdprintk() to a more
fitting place -- after ide_get_best_pio_mode() call;
- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;
- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];
- in the speedproc() method, get rid of the duplicate reads/writes from/to the
UDIDETCRx registers and of the extra variable used to store the transfer mode
value after filtering, use another method of determining master/slave drive,
and cleanup useless parens;
- beautify cmdprintk() output here and there.
While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma(). Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well. While at it, cleanup style in several places.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The subsystem rwsem is not used by the driver core at all, so the use of
it in the ide-proc code of it doesn't make any sense. Perhaps a local
lock might be needed, but I do not really think so.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: linux ide <linux-ide@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ide_hwif_to_major[] has only 10 entries as there are 10 major numbers
reserved for IDE (if somebody needs more it shouldn't be hard to fix).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver crashes the kernel on HPT302N chips due to the missing initializer
for 'hpt302n.settings' having been unfortunately overlooked so far. :-<
Much thanks to Mike Mattie for pin-pointing the reason of crash.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add PCI ID for a newer variant of cardbus CF/IDE adapter card.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add "optical" to sysfs "media" attribute as already in /proc
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I get the following error messages when trying to open a CD device
(specifically, the Teac CD-ROM CD-224E) that has no media present:
hda: packet command error: status=3D0x51 { DriveReady SeekComplete Error }
hda: packet command error: error=3D0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
This happens when a "start stop unit" command (0x1b 0 0 0 3 0 0 0 0 0)
is sent to the drive to try to close the CD-ROM tray, but this drive
doesn't have that capability (it's a slim portable-type CD-ROM), so it
reports sense key 5 (illegal request) with asc/ascq 24/0. This is
exactly how SFF8090i says it should respond.
But ide-cd.c (in cdrom_decode_status() ) just sees sense key 5 and spews
out an error. It then goes on to request sense data, and
cdrom_log_sense() understands this error and doesn't log it.
The patch, for kernel 2.6.20.4, suppresses this error message.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is possible for the timer expiry function to run even though the
request has already been handled: ide_timer_expiry() only checks that
the handler is not NULL, but it is possible that we have handled a
request (thus clearing the handler) and then started a new request
(thus starting the timer again, and setting a handler).
A simple way to exhibit this is to set the DMA timeout to 1 jiffy and
run dd: The kernel will panic after a few minutes because
ide_timer_expiry() tries to add a timer when it's already active.
To fix this, we simply add a request generation count that gets
incremented at every interrupt, and check in ide_timer_expiry() that
we have not already handled a new interrupt before running the expiry
function.
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLEÂ IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling). The correct thing to do is issue a SRST
followed by a SET FEATURES command. This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.
Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
other commands (except IDENTIFY) so send SET FEATURES only if there are
no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[ bart: the ressurection of 2 years old patch which slipped thru the cracks
(thanks to Sergei Shtylyov for finding it) ]
These is the patch to turn on pdc202xx_new for ATAPI DMA. When testing, it
works fine without the (request_bufflen % 256) workaround as needed in libata.
ide-scsi filters out (pc->request_transfer % 1024) and use PIO, so the pdc202xx
ATAPI DMA problem is avoid. Both ide-cd and ide-scsi won't hit the ATAPI DMA
problem on pdc202xx_new.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since especially Serial ATA has it's own menu point now, I guess we can
change the description of the deprecated SATA driver as well, since the
new libATA subsystem is not configured through a SCSI low-level driver
anymore, but has it's own menu point.
From: Patrick Ringl <patrick_@freenet.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>