The aesni_gcm_enc/dec functions can access memory after the end of
the AAD buffer if the AAD length is not a multiple of 4 bytes.
It didn't matter with rfc4106-gcm-aesni as in that case the AAD was
always followed by the 8 byte IV, but that is no longer the case with
generic-gcm-aesni. This can potentially result in accessing a page that
is not mapped and thus causing the machine to crash. This patch fixes
that by reading the last <16 byte block of the AAD byte-by-byte and
optionally via an 8-byte load if the block was at least 8 bytes.
Fixes: 0487ccac ("crypto: aesni - make non-AVX AES-GCM work with any aadlen")
Cc: <stable@vger.kernel.org>
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The aesni_gcm_enc/dec functions can access memory before the start of
the data buffer if the length of the data buffer is less than 16 bytes.
This is because they perform the read via a single 16-byte load. This
can potentially result in accessing a page that is not mapped and thus
causing the machine to crash. This patch fixes that by reading the
partial block byte-by-byte and optionally an via 8-byte load if the block
was at least 8 bytes.
Fixes: 0487ccac ("crypto: aesni - make non-AVX AES-GCM work with any aadlen")
Cc: <stable@vger.kernel.org>
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using %rbp as a temporary register breaks frame pointer convention and
breaks stack traces when unwinding from an interrupt in the crypto code.
In twofish-3way, we can't simply replace %rbp with another register
because there are none available. Instead, we use the stack to hold the
values that %rbp, %r11, and %r12 were holding previously. Each of these
values represents the half of the output from the previous Feistel round
that is being passed on unchanged to the following round. They are only
used once per round, when they are exchanged with %rax, %rbx, and %rcx.
As a result, we free up 3 registers (one per block) and can reassign
them so that %rbp is not used, and additionally %r14 and %r15 are not
used so they do not need to be saved/restored.
There may be a small overhead caused by replacing 'xchg REG, REG' with
the needed sequence 'mov MEM, REG; mov REG, MEM; mov REG, REG' once per
round. But, counterintuitively, when I tested "ctr-twofish-3way" on a
Haswell processor, the new version was actually about 2% faster.
(Perhaps 'xchg' is not as well optimized as plain moves.)
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When I added generic-gcm-aes I didn't add a wrapper like the one
provided for rfc4106(gcm(aes)). We need to add a cryptd wrapper to fall
back on in case the FPU is not available, otherwise we might corrupt the
FPU state.
Fixes: cce2ea8d90 ("crypto: aesni - add generic gcm(aes)")
Cc: <stable@vger.kernel.org>
Reported-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
generic_gcmaes_decrypt needs to use generic_gcmaes_ctx, not
aesni_rfc4106_gcm_ctx. This is actually harmless because the fields in
struct generic_gcmaes_ctx share the layout of the same fields in
aesni_rfc4106_gcm_ctx.
Fixes: cce2ea8d90 ("crypto: aesni - add generic gcm(aes)")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ARM:
* A number of issues in the vgic discovered using SMATCH
* A bit one-off calculation in out stage base address mask (32-bit and
64-bit)
* Fixes to single-step debugging instructions that trap for other
reasons such as MMMIO aborts
* Printing unavailable hyp mode as error
* Potential spinlock deadlock in the vgic
* Avoid calling vgic vcpu free more than once
* Broken bit calculation for big endian systems
s390:
* SPDX tags
* Fence storage key accesses from problem state
* Make sure that irq_state.flags is not used in the future
x86:
* Intercept port 0x80 accesses to prevent host instability (CVE)
* Use userspace FPU context for guest FPU (mainly an optimization that
fixes a double use of kernel FPU)
* Do not leak one page per module load
* Flush APIC page address cache from MMU invalidation notifiers
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJaLA93AAoJEED/6hsPKofo9msH/2DrqT2FOKfLuxNR2FeUGWr3
lqFoBRUXrVDMINGStnWrV36h/xYzlgJl9jtSDS8dr3VxLqtrNLlDg9NmGeogoZ+k
/xewr/jFYoSRfffsvrbkzORUfvu6zqvJwufiwBEJwAfcswiLqPizdFXcxtUL4eZE
9s9sIweo5zp2Xjg5yLOEkyanePKMEht/81zPkHyM+g0ZMoaPam3qZHA0lLzdyRgd
G9LpSyiMFHguYYgbwipaVue3zgMY1EdmKQ8C2hEPmZd8nVau26YDwRnAwwLrmVkW
sFhGO1Xi18TzQPokzALC25c9v0fqgxL5+fNyFNgWwTc2n9PSwO+IHcy699UH+3A=
=Qcqd
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- A number of issues in the vgic discovered using SMATCH
- A bit one-off calculation in out stage base address mask (32-bit
and 64-bit)
- Fixes to single-step debugging instructions that trap for other
reasons such as MMMIO aborts
- Printing unavailable hyp mode as error
- Potential spinlock deadlock in the vgic
- Avoid calling vgic vcpu free more than once
- Broken bit calculation for big endian systems
s390:
- SPDX tags
- Fence storage key accesses from problem state
- Make sure that irq_state.flags is not used in the future
x86:
- Intercept port 0x80 accesses to prevent host instability (CVE)
- Use userspace FPU context for guest FPU (mainly an optimization
that fixes a double use of kernel FPU)
- Do not leak one page per module load
- Flush APIC page address cache from MMU invalidation notifiers"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
KVM: x86: fix APIC page invalidation
KVM: s390: Fix skey emulation permission check
KVM: s390: mark irq_state.flags as non-usable
KVM: s390: Remove redundant license text
KVM: s390: add SPDX identifiers to the remaining files
KVM: VMX: fix page leak in hardware_setup()
KVM: VMX: remove I/O port 0x80 bypass on Intel hosts
x86,kvm: remove KVM emulator get_fpu / put_fpu
x86,kvm: move qemu/guest FPU switching out to vcpu_run
KVM: arm/arm64: Fix broken GICH_ELRSR big endian conversion
KVM: arm/arm64: kvm_arch_destroy_vm cleanups
KVM: arm/arm64: Fix spinlock acquisition in vgic_set_owner
kvm: arm: don't treat unavailable HYP mode as an error
KVM: arm/arm64: Avoid attempting to load timer vgic state without a vgic
kvm: arm64: handle single-step of hyp emulated mmio instructions
kvm: arm64: handle single-step during SError exceptions
kvm: arm64: handle single-step of userspace mmio instructions
kvm: arm64: handle single-stepping trapped instructions
KVM: arm/arm64: debug: Introduce helper for single-step
arm: KVM: Fix VTTBR_BADDR_MASK BUG_ON off-by-one
...
Commit 4675ff05de ("kmemcheck: rip it out") has removed the code but
for some reason SPDX header stayed in place. This looks like a rebase
mistake in the mmotm tree or the merge mistake. Let's drop those
leftovers as well.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
drivers).
2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
to userspace and broke some apps. From Johannes Berg.
3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
Wang.
4) Gianfar MAC can't do EEE so don't advertise it by default, from
Claudiu Manoil.
5) Relax strict netlink attribute validation, but emit a warning. From
David Ahern.
6) Fix regression in checksum offload of thunderx driver, from Florian
Westphal.
7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.
8) New card support in iwlwifi, from Ihab Zhaika.
9) BBR congestion control bug fixes from Neal Cardwell.
10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.
11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.
12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.
13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
net: mvpp2: fix the RSS table entry offset
tcp: evaluate packet losses upon RTT change
tcp: fix off-by-one bug in RACK
tcp: always evaluate losses in RACK upon undo
tcp: correctly test congestion state in RACK
bnxt_en: Fix sources of spurious netpoll warnings
tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
tcp_bbr: reset full pipe detection on loss recovery undo
tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
sfc: pass valid pointers from efx_enqueue_unwind
gianfar: Disable EEE autoneg by default
tcp: invalidate rate samples during SACK reneging
can: peak/pcie_fd: fix potential bug in restarting tx queue
can: usb_8dev: cancel urb on -EPIPE and -EPROTO
can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
can: esd_usb2: cancel urb on -EPIPE and -EPROTO
can: ems_usb: cancel urb on -EPIPE and -EPROTO
can: mcba_usb: cancel urb on -EPROTO
usbnet: fix alignment for frames with no ethernet header
tcp: use current time in tcp_rcv_space_adjust()
...
Pull misc x86 fixes from Ingo Molnar:
- make CR4 handling irq-safe, which bug vmware guests ran into
- don't crash on early IRQs in Xen guests
- don't crash secondary CPU bringup if #UD assisted WARN()ings are
triggered
- make X86_BUG_FXSAVE_LEAK optional on newer AMD CPUs that have the fix
- fix AMD Fam17h microcode loading
- fix broadcom_postcore_init() if ACPI is disabled
- fix resume regression in __restore_processor_context()
- fix Sparse warnings
- fix a GCC-8 warning
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Change time() prototype to match __vdso_time()
x86: Fix Sparse warnings about non-static functions
x86/power: Fix some ordering bugs in __restore_processor_context()
x86/PCI: Make broadcom_postcore_init() check acpi_disabled
x86/microcode/AMD: Add support for fam17h microcode loading
x86/cpufeatures: Make X86_BUG_FXSAVE_LEAK detectable in CPUID on AMD
x86/idt: Load idt early in start_secondary
x86/xen: Support early interrupts in xen pv guests
x86/tlb: Disable interrupts when changing CR4
x86/tlb: Refactor CR4 setting and shadow write
gcc-8 warns that time() is an alias for __vdso_time() but the two
have different prototypes:
arch/x86/entry/vdso/vclock_gettime.c:327:5: error: 'time' alias between functions of incompatible types 'int(time_t *)' {aka 'int(long int *)'} and 'time_t(time_t *)' {aka 'long int(long int *)'} [-Werror=attribute-alias]
int time(time_t *t)
^~~~
arch/x86/entry/vdso/vclock_gettime.c:318:16: note: aliased declaration here
I could not figure out whether this is intentional, but I see that
changing it to return time_t avoids the warning.
Returning 'int' from time() is also a bit questionable, as it causes an
overflow in y2038 even on 64-bit architectures that use a 64-bit time_t
type. On 32-bit architecture with 64-bit time_t, time() should always
be implement by the C library by calling a (to be added) clock_gettime()
variant that takes a sufficiently wide argument.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: http://lkml.kernel.org/r/20171204150203.852959-1-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Functions x86_vector_debug_show(), uv_handle_nmi() and uv_nmi_setup_common()
are local to the source and do not need to be in global scope, so make them
static.
Fixes up various sparse warnings.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mike Travis <mike.travis@hpe.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <russ.anderson@hpe.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Cc: travis@sgi.com
Link: http://lkml.kernel.org/r/20171206173358.24388-1-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implementation of the unpinned APIC page didn't update the VMCS address
cache when invalidation was done through range mmu notifiers.
This became a problem when the page notifier was removed.
Re-introduce the arch-specific helper and call it from ...range_start.
Reported-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Fixes: 38b9917350 ("kvm: vmx: Implement set_apic_access_page_addr")
Fixes: 369ea8242c ("mm/rmap: update to new mmu_notifier semantic v2")
Cc: <stable@vger.kernel.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Wanpeng Li <wanpeng.li@hotmail.com>
Tested-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
__restore_processor_context() had a couple of ordering bugs. It
restored GSBASE after calling load_gs_index(), and the latter can
call into tracing code. It also tried to restore segment registers
before restoring the LDT, which is straight-up wrong.
Reorder the code so that we restore GSBASE, then the descriptor
tables, then the segments.
This fixes two bugs. First, it fixes a regression that broke resume
under certain configurations due to irqflag tracing in
native_load_gs_index(). Second, it fixes resume when the userspace
process that initiated suspect had funny segments. The latter can be
reproduced by compiling this:
// SPDX-License-Identifier: GPL-2.0
/*
* ldt_echo.c - Echo argv[1] while using an LDT segment
*/
int main(int argc, char **argv)
{
int ret;
size_t len;
char *buf;
const struct user_desc desc = {
.entry_number = 0,
.base_addr = 0,
.limit = 0xfffff,
.seg_32bit = 1,
.contents = 0, /* Data, grow-up */
.read_exec_only = 0,
.limit_in_pages = 1,
.seg_not_present = 0,
.useable = 0
};
if (argc != 2)
errx(1, "Usage: %s STRING", argv[0]);
len = asprintf(&buf, "%s\n", argv[1]);
if (len < 0)
errx(1, "Out of memory");
ret = syscall(SYS_modify_ldt, 1, &desc, sizeof(desc));
if (ret < -1)
errno = -ret;
if (ret)
err(1, "modify_ldt");
asm volatile ("movw %0, %%es" :: "rm" ((unsigned short)7));
write(1, buf, len);
return 0;
}
and running ldt_echo >/sys/power/mem
Without the fix, the latter causes a triple fault on resume.
Fixes: ca37e57bbe ("x86/entry/64: Add missing irqflags tracing to native_load_gs_index()")
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/6b31721ea92f51ea839e79bd97ade4a75b1eeea2.1512057304.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
acpi_os_get_root_pointer() may return a valid address even if acpi_disabled
is set, but the host bridge information from the ACPI tables is not going
to be used in that case and the Broadcom host bridge initialization should
not be skipped then, So make broadcom_postcore_init() check acpi_disabled
too to avoid this issue.
Fixes: 6361d72b04 (x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan)
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/3186627.pxZj1QbYNg@aspire.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The size for the Microcode Patch Block (MPB) for an AMD family 17h
processor is 3200 bytes. Add a #define for fam17h so that it does
not default to 2048 bytes and fail a microcode load/update.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20171130224640.15391.40247.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The latest AMD AMD64 Architecture Programmer's Manual
adds a CPUID feature XSaveErPtr (CPUID_Fn80000008_EBX[2]).
If this feature is set, the FXSAVE, XSAVE, FXSAVEOPT, XSAVEC, XSAVES
/ FXRSTOR, XRSTOR, XRSTORS always save/restore error pointers,
thus making the X86_BUG_FXSAVE_LEAK workaround obsolete on such CPUs.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Link: https://lkml.kernel.org/r/bdcebe90-62c5-1f05-083c-eba7f08b2540@assembler.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Things like this will probably keep showing up for other architectures
and other special cases.
I actually thought we already used %lx for this, and that is indeed
_historically_ the case, but we moved to %p when merging the 32-bit and
64-bit cases as a convenient way to get the formatting right (ie
automatically picking "%08lx" vs "%016lx" based on register size).
So just turn this %p into %px.
Reported-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The refcount_t protection on x86 was not intended to use the stricter
GPL export. This adjusts the linkage again to avoid a regression in
the availability of the refcount API.
Reported-by: Dave Airlie <airlied@gmail.com>
Fixes: 7a46ec0e2f ("locking/refcounts, x86/asm: Implement fast refcount overflow protection")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vmx_io_bitmap_b should not be allocated twice.
Fixes: 2361133293 ("KVM: VMX: refactor setup of global page-sized bitmaps")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This fixes CVE-2017-1000407.
KVM allows guests to directly access I/O port 0x80 on Intel hosts. If
the guest floods this port with writes it generates exceptions and
instability in the host kernel, leading to a crash. With this change
guest writes to port 0x80 on Intel will behave the same as they
currently behave on AMD systems.
Prevent the flooding by removing the code that sets port 0x80 as a
passthrough port. This is essentially the same as upstream patch
99f85a28a7, except that patch was
for AMD chipsets and this patch is for Intel.
Signed-off-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Fixes: fdef3ad1b3 ("KVM: VMX: Enable io bitmaps to avoid IO port 0x80 VMEXITs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Now that get_fpu and put_fpu do nothing, because the scheduler will
automatically load and restore the guest FPU context for us while we
are in this code (deep inside the vcpu_run main loop), we can get rid
of the get_fpu and put_fpu hooks.
Signed-off-by: Rik van Riel <riel@redhat.com>
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, every time a VCPU is scheduled out, the host kernel will
first save the guest FPU/xstate context, then load the qemu userspace
FPU context, only to then immediately save the qemu userspace FPU
context back to memory. When scheduling in a VCPU, the same extraneous
FPU loads and saves are done.
This could be avoided by moving from a model where the guest FPU is
loaded and stored with preemption disabled, to a model where the
qemu userspace FPU is swapped out for the guest FPU context for
the duration of the KVM_RUN ioctl.
This is done under the VCPU mutex, which is also taken when other
tasks inspect the VCPU FPU context, so the code should already be
safe for this change. That should come as no surprise, given that
s390 already has this optimization.
This can fix a bug where KVM calls get_user_pages while owning the
FPU, and the file system ends up requesting the FPU again:
[258270.527947] __warn+0xcb/0xf0
[258270.527948] warn_slowpath_null+0x1d/0x20
[258270.527951] kernel_fpu_disable+0x3f/0x50
[258270.527953] __kernel_fpu_begin+0x49/0x100
[258270.527955] kernel_fpu_begin+0xe/0x10
[258270.527958] crc32c_pcl_intel_update+0x84/0xb0
[258270.527961] crypto_shash_update+0x3f/0x110
[258270.527968] crc32c+0x63/0x8a [libcrc32c]
[258270.527975] dm_bm_checksum+0x1b/0x20 [dm_persistent_data]
[258270.527978] node_prepare_for_write+0x44/0x70 [dm_persistent_data]
[258270.527985] dm_block_manager_write_callback+0x41/0x50 [dm_persistent_data]
[258270.527988] submit_io+0x170/0x1b0 [dm_bufio]
[258270.527992] __write_dirty_buffer+0x89/0x90 [dm_bufio]
[258270.527994] __make_buffer_clean+0x4f/0x80 [dm_bufio]
[258270.527996] __try_evict_buffer+0x42/0x60 [dm_bufio]
[258270.527998] dm_bufio_shrink_scan+0xc0/0x130 [dm_bufio]
[258270.528002] shrink_slab.part.40+0x1f5/0x420
[258270.528004] shrink_node+0x22c/0x320
[258270.528006] do_try_to_free_pages+0xf5/0x330
[258270.528008] try_to_free_pages+0xe9/0x190
[258270.528009] __alloc_pages_slowpath+0x40f/0xba0
[258270.528011] __alloc_pages_nodemask+0x209/0x260
[258270.528014] alloc_pages_vma+0x1f1/0x250
[258270.528017] do_huge_pmd_anonymous_page+0x123/0x660
[258270.528021] handle_mm_fault+0xfd3/0x1330
[258270.528025] __get_user_pages+0x113/0x640
[258270.528027] get_user_pages+0x4f/0x60
[258270.528063] __gfn_to_pfn_memslot+0x120/0x3f0 [kvm]
[258270.528108] try_async_pf+0x66/0x230 [kvm]
[258270.528135] tdp_page_fault+0x130/0x280 [kvm]
[258270.528149] kvm_mmu_page_fault+0x60/0x120 [kvm]
[258270.528158] handle_ept_violation+0x91/0x170 [kvm_intel]
[258270.528162] vmx_handle_exit+0x1ca/0x1400 [kvm_intel]
No performance changes were detected in quick ping-pong tests on
my 4 socket system, which is expected since an FPU+xstate load is
on the order of 0.1us, while ping-ponging between CPUs is on the
order of 20us, and somewhat noisy.
Cc: stable@vger.kernel.org
Signed-off-by: Rik van Riel <riel@redhat.com>
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[Fixed a bug where reset_vcpu called put_fpu without preceding load_fpu,
which happened inside from KVM_CREATE_VCPU ioctl. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Commit 0515e5999a ("bpf: introduce BPF_PROG_TYPE_PERF_EVENT
program type") introduced the bpf_perf_event_data structure which
exports the pt_regs structure. This is OK for multiple architectures
but fail for s390 and arm64 which do not export pt_regs. Programs
using them, for example, the bpf selftest fail to compile on these
architectures.
For s390, exporting the pt_regs is not an option because s390 wants
to allow changes to it. For arm64, there is a user_pt_regs structure
that covers parts of the pt_regs structure for use by user space.
To solve the broken uapi for s390 and arm64, introduce an abstract
type for pt_regs and add an asm/bpf_perf_event.h file that concretes
the type. An asm-generic header file covers the architectures that
export pt_regs today.
The arch-specific enablement for s390 and arm64 follows in separate
commits.
Reported-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Fixes: 0515e5999a ("bpf: introduce BPF_PROG_TYPE_PERF_EVENT program type")
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-and-tested-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
* PPC bugfix: HPT guests on a POWER9 radix host
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJaICi1AAoJEL/70l94x66DjvEIAIML/e9YX1YrJZi0rsB9cbm0
Le3o5b3wKxPrlZdnpOZQ2mVWubUQdiHMPGX6BkpgyiJWUchnbj5ql1gUf5S0i3jk
TOk6nae6DU94xBuboeqZJlmx2VfPY/fqzLWsX3HFHpnzRl4XvXL5o7cWguIxVcVO
yU6bPgbAXyXSBennLWZxC3aQ2Ojikr3uxZQpUZTAPOW5hFINpCKCpqJBMxsb67wq
rwI0cJhRl92mHpbe8qeNJhavqY5eviy9iPUaZrOW9P4yw1uqjTAjgsUc1ydiaZSV
rOHeKBOgVfY/KBaNJKyKySfuL1MJ+DLcQqm9RlGpKNpFIeB0vvSf0gtmmqIAXIk=
=kh2y
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
- x86 bugfixes: APIC, nested virtualization, IOAPIC
- PPC bugfix: HPT guests on a POWER9 radix host
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (26 commits)
KVM: Let KVM_SET_SIGNAL_MASK work as advertised
KVM: VMX: Fix vmx->nested freeing when no SMI handler
KVM: VMX: Fix rflags cache during vCPU reset
KVM: X86: Fix softlockup when get the current kvmclock
KVM: lapic: Fixup LDR on load in x2apic
KVM: lapic: Split out x2apic ldr calculation
KVM: PPC: Book3S HV: Fix migration and HPT resizing of HPT guests on radix hosts
KVM: vmx: use X86_CR4_UMIP and X86_FEATURE_UMIP
KVM: x86: Fix CPUID function for word 6 (80000001_ECX)
KVM: nVMX: Fix vmx_check_nested_events() return value in case an event was reinjected to L2
KVM: x86: ioapic: Preserve read-only values in the redirection table
KVM: x86: ioapic: Clear Remote IRR when entry is switched to edge-triggered
KVM: x86: ioapic: Remove redundant check for Remote IRR in ioapic_set_irq
KVM: x86: ioapic: Don't fire level irq when Remote IRR set
KVM: x86: ioapic: Fix level-triggered EOI and IOAPIC reconfigure race
KVM: x86: inject exceptions produced by x86_decode_insn
KVM: x86: Allow suppressing prints on RDMSR/WRMSR of unhandled MSRs
KVM: x86: fix em_fxstor() sleeping while in atomic
KVM: nVMX: Fix mmu context after VMLAUNCH/VMRESUME failure
KVM: nVMX: Validate the IA32_BNDCFGS on nested VM-entry
...
In response to compile breakage introduced by a series that added the
pud_write helper to x86, Stephen notes:
did you consider using the other paradigm:
In arch include files:
#define pud_write pud_write
static inline int pud_write(pud_t pud)
.....
Then in include/asm-generic/pgtable.h:
#ifndef pud_write
tatic inline int pud_write(pud_t pud)
{
....
}
#endif
If you had, then the powerpc code would have worked ... ;-) and many
of the other interfaces in include/asm-generic/pgtable.h are
protected that way ...
Given that some architecture already define pmd_write() as a macro, it's
a net reduction to drop the definition of __HAVE_ARCH_PMD_WRITE.
Link: http://lkml.kernel.org/r/151129126721.37405.13339850900081557813.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently only get_user_pages_fast() can safely handle the writable gup
case due to its use of pud_access_permitted() to check whether the pud
entry is writable. In the gup slow path pud_write() is used instead of
pud_access_permitted() and to date it has been unimplemented, just calls
BUG_ON().
kernel BUG at ./include/linux/hugetlb.h:244!
[..]
RIP: 0010:follow_devmap_pud+0x482/0x490
[..]
Call Trace:
follow_page_mask+0x28c/0x6e0
__get_user_pages+0xe4/0x6c0
get_user_pages_unlocked+0x130/0x1b0
get_user_pages_fast+0x89/0xb0
iov_iter_get_pages_alloc+0x114/0x4a0
nfs_direct_read_schedule_iovec+0xd2/0x350
? nfs_start_io_direct+0x63/0x70
nfs_file_direct_read+0x1e0/0x250
nfs_file_read+0x90/0xc0
For now this just implements a simple check for the _PAGE_RW bit similar
to pmd_write. However, this implies that the gup-slow-path check is
missing the extra checks that the gup-fast-path performs with
pud_access_permitted. Later patches will align all checks to use the
'access_permitted' helper if the architecture provides it.
Note that the generic 'access_permitted' helper fallback is the simple
_PAGE_RW check on architectures that do not define the
'access_permitted' helper(s).
[dan.j.williams@intel.com: fix powerpc compile error]
Link: http://lkml.kernel.org/r/151129126165.37405.16031785266675461397.stgit@dwillia2-desk3.amr.corp.intel.com
Link: http://lkml.kernel.org/r/151043109938.2842.14834662818213616199.stgit@dwillia2-desk3.amr.corp.intel.com
Fixes: a00cc7d9dd ("mm, x86: add support for PUD-sized transparent hugepages")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de> [x86]
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the generic ChaCha20 implementation no longer needs a
cra_alignmask, the x86 one doesn't either -- given that the x86
implementation doesn't need the alignment itself.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When asked to encrypt or decrypt 0 bytes, both the generic and x86
implementations of Salsa20 crash in blkcipher_walk_done(), either when
doing 'kfree(walk->buffer)' or 'free_page((unsigned long)walk->page)',
because walk->buffer and walk->page have not been initialized.
The bug is that Salsa20 is calling blkcipher_walk_done() even when
nothing is in 'walk.nbytes'. But blkcipher_walk_done() is only meant to
be called when a nonzero number of bytes have been provided.
The broken code is part of an optimization that tries to make only one
call to salsa20_encrypt_bytes() to process inputs that are not evenly
divisible by 64 bytes. To fix the bug, just remove this "optimization"
and use the blkcipher_walk API the same way all the other users do.
Reproducer:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
int algfd, reqfd;
struct sockaddr_alg addr = {
.salg_type = "skcipher",
.salg_name = "salsa20",
};
char key[16] = { 0 };
algfd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(algfd, (void *)&addr, sizeof(addr));
reqfd = accept(algfd, 0, 0);
setsockopt(algfd, SOL_ALG, ALG_SET_KEY, key, sizeof(key));
read(reqfd, key, sizeof(key));
}
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: eb6f13eb9f ("[CRYPTO] salsa20_generic: Fix multi-page processing")
Cc: <stable@vger.kernel.org> # v2.6.25+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On a secondary, idt is first loaded in cpu_init() with load_current_idt(),
i.e. no exceptions can be handled before that point.
The conversion of WARN() to use UD requires the IDT being loaded earlier as
any warning between start_secondary() and load_curren_idt() in cpu_init()
will result in an unhandled @UD exception and therefore fail the bringup of
the CPU.
Install the IDT handlers right in start_secondary() before calling cpu_init().
[ tglx: Massaged changelog ]
Fixes: 9a93848fe7 ("x86/debug: Implement __WARN() using UD0")
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: peterz@infradead.org
Cc: bp@alien8.de
Cc: rostedt@goodmis.org
Cc: luto@kernel.org
Link: https://lkml.kernel.org/r/1511792499-4073-1-git-send-email-chuhu@redhat.com
KVM API says for the signal mask you set via KVM_SET_SIGNAL_MASK, that
"any unblocked signal received [...] will cause KVM_RUN to return with
-EINTR" and that "the signal will only be delivered if not blocked by
the original signal mask".
This, however, is only true, when the calling task has a signal handler
registered for a signal. If not, signal evaluation is short-circuited for
SIG_IGN and SIG_DFL, and the signal is either ignored without KVM_RUN
returning or the whole process is terminated.
Make KVM_SET_SIGNAL_MASK behave as advertised by utilizing logic similar
to that in do_sigtimedwait() to avoid short-circuiting of signals.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by syzkaller:
------------[ cut here ]------------
WARNING: CPU: 5 PID: 2939 at arch/x86/kvm/vmx.c:3844 free_loaded_vmcs+0x77/0x80 [kvm_intel]
CPU: 5 PID: 2939 Comm: repro Not tainted 4.14.0+ #26
RIP: 0010:free_loaded_vmcs+0x77/0x80 [kvm_intel]
Call Trace:
vmx_free_vcpu+0xda/0x130 [kvm_intel]
kvm_arch_destroy_vm+0x192/0x290 [kvm]
kvm_put_kvm+0x262/0x560 [kvm]
kvm_vm_release+0x2c/0x30 [kvm]
__fput+0x190/0x370
task_work_run+0xa1/0xd0
do_exit+0x4d2/0x13e0
do_group_exit+0x89/0x140
get_signal+0x318/0xb80
do_signal+0x8c/0xb40
exit_to_usermode_loop+0xe4/0x140
syscall_return_slowpath+0x206/0x230
entry_SYSCALL_64_fastpath+0x98/0x9a
The syzkaller testcase will execute VMXON/VMLAUCH instructions, so the
vmx->nested stuff is populated, it will also issue KVM_SMI ioctl. However,
the testcase is just a simple c program and not be lauched by something
like seabios which implements smi_handler. Commit 05cade71cf (KVM: nSVM:
fix SMI injection in guest mode) gets out of guest mode and set nested.vmxon
to false for the duration of SMM according to SDM 34.14.1 "leave VMX
operation" upon entering SMM. We can't alloc/free the vmx->nested stuff
each time when entering/exiting SMM since it will induce more overhead. So
the function vmx_pre_enter_smm() marks nested.vmxon false even if vmx->nested
stuff is still populated. What it expected is em_rsm() can mark nested.vmxon
to be true again. However, the smi_handler/rsm will not execute since there
is no something like seabios in this scenario. The function free_nested()
fails to free the vmx->nested stuff since the vmx->nested.vmxon is false
which results in the above warning.
This patch fixes it by also considering the no SMI handler case, luckily
vmx->nested.smm.vmxon is marked according to the value of vmx->nested.vmxon
in vmx_pre_enter_smm(), we can take advantage of it and free vmx->nested
stuff when L1 goes down.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Fixes: 05cade71cf (KVM: nSVM: fix SMI injection in guest mode)
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by syzkaller:
*** Guest State ***
CR0: actual=0x0000000080010031, shadow=0x0000000060000010, gh_mask=fffffffffffffff7
CR4: actual=0x0000000000002061, shadow=0x0000000000000000, gh_mask=ffffffffffffe8f1
CR3 = 0x000000002081e000
RSP = 0x000000000000fffa RIP = 0x0000000000000000
RFLAGS=0x00023000 DR7 = 0x00000000000000
^^^^^^^^^^
------------[ cut here ]------------
WARNING: CPU: 6 PID: 24431 at /home/kernel/linux/arch/x86/kvm//x86.c:7302 kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm]
CPU: 6 PID: 24431 Comm: reprotest Tainted: G W OE 4.14.0+ #26
RIP: 0010:kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm]
RSP: 0018:ffff880291d179e0 EFLAGS: 00010202
Call Trace:
kvm_vcpu_ioctl+0x479/0x880 [kvm]
do_vfs_ioctl+0x142/0x9a0
SyS_ioctl+0x74/0x80
entry_SYSCALL_64_fastpath+0x23/0x9a
The failed vmentry is triggered by the following beautified testcase:
#include <unistd.h>
#include <sys/syscall.h>
#include <string.h>
#include <stdint.h>
#include <linux/kvm.h>
#include <fcntl.h>
#include <sys/ioctl.h>
long r[5];
int main()
{
struct kvm_debugregs dr = { 0 };
r[2] = open("/dev/kvm", O_RDONLY);
r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7);
struct kvm_guest_debug debug = {
.control = 0xf0403,
.arch = {
.debugreg[6] = 0x2,
.debugreg[7] = 0x2
}
};
ioctl(r[4], KVM_SET_GUEST_DEBUG, &debug);
ioctl(r[4], KVM_RUN, 0);
}
which testcase tries to setup the processor specific debug
registers and configure vCPU for handling guest debug events through
KVM_SET_GUEST_DEBUG. The KVM_SET_GUEST_DEBUG ioctl will get and set
rflags in order to set TF bit if single step is needed. All regs' caches
are reset to avail and GUEST_RFLAGS vmcs field is reset to 0x2 during vCPU
reset. However, the cache of rflags is not reset during vCPU reset. The
function vmx_get_rflags() returns an unreset rflags cache value since
the cache is marked avail, it is 0 after boot. Vmentry fails if the
rflags reserved bit 1 is 0.
This patch fixes it by resetting both the GUEST_RFLAGS vmcs field and
its cache to 0x2 during vCPU reset.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
watchdog: BUG: soft lockup - CPU#6 stuck for 22s! [qemu-system-x86:10185]
CPU: 6 PID: 10185 Comm: qemu-system-x86 Tainted: G OE 4.14.0-rc4+ #4
RIP: 0010:kvm_get_time_scale+0x4e/0xa0 [kvm]
Call Trace:
get_time_ref_counter+0x5a/0x80 [kvm]
kvm_hv_process_stimers+0x120/0x5f0 [kvm]
kvm_arch_vcpu_ioctl_run+0x4b4/0x1690 [kvm]
kvm_vcpu_ioctl+0x33a/0x620 [kvm]
do_vfs_ioctl+0xa1/0x5d0
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x1e/0xa9
This can be reproduced when running kvm-unit-tests/hyperv_stimer.flat and
cpu-hotplug stress simultaneously. __this_cpu_read(cpu_tsc_khz) returns 0
(set in kvmclock_cpu_down_prep()) when the pCPU is unhotplug which results
in kvm_get_time_scale() gets into an infinite loop.
This patch fixes it by treating the unhotplug pCPU as not using master clock.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In x2apic mode the LDR is fixed based on the ID rather
than separately loadable like it was before x2.
When kvm_apic_set_state is called, the base is set, and if
it has the X2APIC_ENABLE flag set then the LDR is calculated;
however that value gets overwritten by the memcpy a few lines
below overwriting it with the value that came from userland.
The symptom is a lack of EOI after loading the state
(e.g. after a QEMU migration) and is due to the EOI bitmap
being wrong due to the incorrect LDR. This was seen with
a Win2016 guest under Qemu with irqchip=split whose USB mouse
didn't work after a VM migration.
This corresponds to RH bug:
https://bugzilla.redhat.com/show_bug.cgi?id=1502591
Reported-by: Yiqian Wei <yiwei@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: stable@vger.kernel.org
[Applied fixup from Liran Alon. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Split out the ldr calculation from kvm_apic_set_x2apic_id
since we're about to reuse it in the following patch.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull misc x86 fixes from Ingo Molnar:
- topology enumeration fixes
- KASAN fix
- two entry fixes (not yet the big series related to KASLR)
- remove obsolete code
- instruction decoder fix
- better /dev/mem sanity checks, hopefully working better this time
- pkeys fixes
- two ACPI fixes
- 5-level paging related fixes
- UMIP fixes that should make application visible faults more debuggable
- boot fix for weird virtualization environment
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/decoder: Add new TEST instruction pattern
x86/PCI: Remove unused HyperTransport interrupt support
x86/umip: Fix insn_get_code_seg_params()'s return value
x86/boot/KASLR: Remove unused variable
x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
x86/pkeys/selftests: Fix protection keys write() warning
x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
x86/mpx/selftests: Fix up weird arrays
x86/pkeys: Update documentation about availability
x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
x86/smpboot: Fix __max_logical_packages estimate
x86/topology: Avoid wasting 128k for package id array
perf/x86/intel/uncore: Cache logical pkg id in uncore driver
x86/acpi: Reduce code duplication in mp_override_legacy_irq()
x86/acpi: Handle SCI interrupts above legacy space gracefully
x86/boot: Fix boot failure when SMP MP-table is based at 0
x86/mm: Limit mmap() of /dev/mem to valid physical addresses
x86/selftests: Add test for mapping placement for 5-level paging
...
Pull perf fixes from Ingo Molnar:
"Misc fixes: two PMU driver fixes and a memory leak fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix memory leak triggered by perf --namespace
perf/x86/intel/uncore: Add event constraint for BDX PCU
perf/x86/intel: Hide TSX events when RTM is not supported
CR4 modifications are implemented as RMW operations which update a shadow
variable and write the result to CR4. The RMW operation is protected by
preemption disable, but there is no enforcement or debugging mechanism.
CR4 modifications happen also in interrupt context via
__native_flush_tlb_global(). This implementation does not affect a
interrupted thread context CR4 operation, because the CR4 toggle restores
the original content and does not modify the shadow variable.
So the current situation seems to be safe, but a recent patch tried to add
an actual RMW operation in interrupt context, which will cause subtle
corruptions.
To prevent that and make the CR4 handling future proof:
- Add a lockdep assertion to __cr4_set() which will catch interrupt
enabled invocations
- Disable interrupts in the cr4 manipulator inlines
- Rename cr4_toggle_bits() to cr4_toggle_bits_irqsoff(). This is called
from __switch_to_xtra() where interrupts are already disabled and
performance matters.
All other call sites are not performance critical, so the extra overhead of
an additional local_irq_save/restore() pair is not a problem. If new call
sites care about performance then the necessary _irqsoff() variants can be
added.
[ tglx: Condensed the patch by moving the irq protection inside the
manipulator functions. Updated changelog ]
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Luck <tony.luck@intel.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: nadav.amit@gmail.com
Cc: linux-edac@vger.kernel.org
Link: https://lkml.kernel.org/r/20171125032907.2241-3-namit@vmware.com
Refactor the write to CR4 and its shadow value. This is done in
preparation for the addition of an assertion to check that IRQs are
disabled during CR4 update.
No functional change.
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: nadav.amit@gmail.com
Cc: Andy Lutomirski <luto@kernel.org>
Cc: linux-edac@vger.kernel.org
Link: https://lkml.kernel.org/r/20171125032907.2241-2-namit@vmware.com
* GICv4 Support for KVM/ARM
All ARM patches were in next-20171113. I have postponed most x86 fixes
to 4.15-rc2 and UMIP to 4.16, but there are fixes that would be good to
have already in 4.15-rc1:
* re-introduce support for CPUs without virtual NMI (cc stable)
and allow testing of KVM without virtual NMI on available CPUs
* fix long-standing performance issues with assigned devices on AMD
(cc stable)
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJaGECGAAoJEED/6hsPKofoT08H/AuaMi8qprw2BNpVBbQxWRWM
O4WPk7yz1zB4SkdRNrPzCMBy+qoK7FcV/3BpsFPuQS4NHQ+GvQ87N/7tUbouVyl6
CuPGJMCnNzMQ8GvLOJgB1/sz+uW5W/ph3y8kv1UP3/hNCZU4fqukoUeLroOH/wr6
N3bSY8bok7ycdpgybHmbUHY0Yk4IUk3m0RXWY9U5Jl3sjoNEwCw3pWdrq9Swfs/6
W8QJRdE4Z6KHPqW5sRnPj24IpoUpCxu+IT+gPuGlDUCN/h3sfhYvMS6GgDrCjiiZ
2z1TwaIAo+wGjlBQzGmyTUjUPjbGew+f3ixBlf2BtmNutX+tX2qsVfl1NKXYTto=
=GGge
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"Trimmed second batch of KVM changes for Linux 4.15:
- GICv4 Support for KVM/ARM
- re-introduce support for CPUs without virtual NMI (cc stable) and
allow testing of KVM without virtual NMI on available CPUs
- fix long-standing performance issues with assigned devices on AMD
(cc stable)"
* tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
kvm: vmx: Allow disabling virtual NMI support
kvm: vmx: Reinstate support for CPUs without virtual NMI
KVM: SVM: obey guest PAT
KVM: arm/arm64: Don't queue VLPIs on INV/INVALL
KVM: arm/arm64: Fix GICv4 ITS initialization issues
KVM: arm/arm64: GICv4: Theory of operations
KVM: arm/arm64: GICv4: Enable VLPI support
KVM: arm/arm64: GICv4: Prevent userspace from changing doorbell affinity
KVM: arm/arm64: GICv4: Prevent a VM using GICv4 from being saved
KVM: arm/arm64: GICv4: Enable virtual cpuif if VLPIs can be delivered
KVM: arm/arm64: GICv4: Hook vPE scheduling into vgic flush/sync
KVM: arm/arm64: GICv4: Use the doorbell interrupt as an unblocking source
KVM: arm/arm64: GICv4: Add doorbell interrupt handling
KVM: arm/arm64: GICv4: Use pending_last as a scheduling hint
KVM: arm/arm64: GICv4: Handle INVALL applied to a vPE
KVM: arm/arm64: GICv4: Propagate property updates to VLPIs
KVM: arm/arm64: GICv4: Handle MOVALL applied to a vPE
KVM: arm/arm64: GICv4: Handle CLEAR applied to a VLPI
KVM: arm/arm64: GICv4: Propagate affinity changes to the physical ITS
KVM: arm/arm64: GICv4: Unmap VLPI when freeing an LPI
...
The kbuild test robot reported this build warning:
Warning: arch/x86/tools/test_get_len found difference at <jump_table>:ffffffff8103dd2c
Warning: ffffffff8103dd82: f6 09 d8 testb $0xd8,(%rcx)
Warning: objdump says 3 bytes, but insn_get_length() says 2
Warning: decoded and checked 1569014 instructions with 1 warnings
This sequence seems to be a new instruction not in the opcode map in the Intel SDM.
The instruction sequence is "F6 09 d8", means Group3(F6), MOD(00)REG(001)RM(001), and 0xd8.
Intel SDM vol2 A.4 Table A-6 said the table index in the group is "Encoding of Bits 5,4,3 of
the ModR/M Byte (bits 2,1,0 in parenthesis)"
In that table, opcodes listed by the index REG bits as:
000 001 010 011 100 101 110 111
TEST Ib/Iz,(undefined),NOT,NEG,MUL AL/rAX,IMUL AL/rAX,DIV AL/rAX,IDIV AL/rAX
So, it seems TEST Ib is assigned to 001.
Add the new pattern.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are no in-tree callers of ht_create_irq(), the driver interface for
HyperTransport interrupts, left. Remove the unused entry point and all the
supporting code.
See 8b955b0ddd ("[PATCH] Initial generic hypertransport interrupt
support").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pci@vger.kernel.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: https://lkml.kernel.org/r/20171122221337.3877.23362.stgit@bhelgaas-glaptop.roam.corp.google.com
In order to save on redundant structs definitions
insn_get_code_seg_params() was made to return two 4-bit values in a char
but clang complains:
arch/x86/lib/insn-eval.c:780:10: warning: implicit conversion from 'int' to 'char'
changes value from 132 to -124 [-Wconstant-conversion]
return INSN_CODE_SEG_PARAMS(4, 8);
~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~
./arch/x86/include/asm/insn-eval.h:16:57: note: expanded from macro 'INSN_CODE_SEG_PARAMS'
#define INSN_CODE_SEG_PARAMS(oper_sz, addr_sz) (oper_sz | (addr_sz << 4))
Those two values do get picked apart afterwards the opposite way of how
they were ORed so wrt to the LSByte, the return value is the same.
But this function returns -EINVAL in the error case, which is an int. So
make it return an int which is the native word size anyway and thus fix
the clang warning.
Reported-by: Kees Cook <keescook@google.com>
Reported-by: Nick Desaulniers <nick.desaulniers@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: ricardo.neri-calderon@linux.intel.com
Link: https://lkml.kernel.org/r/20171123091951.1462-1-bp@alien8.de
Running this code with IRQs enabled (where dummy_lock is a spinlock):
static void check_load_gs_index(void)
{
/* This will fail. */
load_gs_index(0xffff);
spin_lock(&dummy_lock);
spin_unlock(&dummy_lock);
}
Will generate a lockdep warning. The issue is that the actual write
to %gs would cause an exception with IRQs disabled, and the exception
handler would, as an inadvertent side effect, update irqflag tracing
to reflect the IRQs-off status. native_load_gs_index() would then
turn IRQs back on and return with irqflag tracing still thinking that
IRQs were off. The dummy lock-and-unlock causes lockdep to notice the
error and warn.
Fix it by adding the missing tracing.
Apparently nothing did this in a context where it mattered. I haven't
tried to find a code path that would actually exhibit the warning if
appropriately nasty user code were running.
I suspect that the security impact of this bug is very, very low --
production systems don't run with lockdep enabled, and the warning is
mostly harmless anyway.
Found during a quick audit of the entry code to try to track down an
unrelated bug that Ingo found in some still-in-development code.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/e1aeb0e6ba8dd430ec36c8a35e63b429698b4132.1511411918.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ Note, this commit is a cherry-picked version of:
d17a1d97dc20: ("x86/mm/kasan: don't use vmemmap_populate() to initialize shadow")
... for easier x86 entry code testing and back-porting. ]
The KASAN shadow is currently mapped using vmemmap_populate() since that
provides a semi-convenient way to map pages into init_top_pgt. However,
since that no longer zeroes the mapped pages, it is not suitable for
KASAN, which requires zeroed shadow memory.
Add kasan_populate_shadow() interface and use it instead of
vmemmap_populate(). Besides, this allows us to take advantage of
gigantic pages and use them to populate the shadow, which should save us
some memory wasted on page tables and reduce TLB pressure.
Link: http://lkml.kernel.org/r/20171103185147.2688-2-pasha.tatashin@oracle.com
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Bob Picco <bob.picco@oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When I added entry_SYSCALL_64_after_hwframe(), I left TRACE_IRQS_OFF
before it. This means that users of entry_SYSCALL_64_after_hwframe()
were responsible for invoking TRACE_IRQS_OFF, and the one and only
user (Xen, added in the same commit) got it wrong.
I think this would manifest as a warning if a Xen PV guest with
CONFIG_DEBUG_LOCKDEP=y were used with context tracking. (The
context tracking bit is to cause lockdep to get invoked before we
turn IRQs back on.) I haven't tested that for real yet because I
can't get a kernel configured like that to boot at all on Xen PV.
Move TRACE_IRQS_OFF below the label.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: 8a9949bc71 ("x86/xen/64: Rearrange the SYSCALL entries")
Link: http://lkml.kernel.org/r/9150aac013b7b95d62c2336751d5b6e91d2722aa.1511325444.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Print a rate-limited warning when a user-space program attempts to execute
any of the instructions that UMIP protects (i.e., SGDT, SIDT, SLDT, STR
and SMSW).
This is useful, because when CONFIG_X86_INTEL_UMIP=y is selected and
supported by the hardware, user space programs that try to execute such
instructions will receive a SIGSEGV signal that they might not expect.
In the specific cases for which emulation is provided (instructions SGDT,
SIDT and SMSW in protected and virtual-8086 modes), no signal is
generated. However, a warning is helpful to encourage updates in such
programs to avoid the use of such instructions.
Warnings are printed via a customized printk() function that also provides
information about the program that attempted to use the affected
instructions.
Utility macros are defined to wrap umip_printk() for the error and warning
kernel log levels.
While here, replace an existing call to the generic rate-limited pr_err()
with the new umip_pr_err().
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi V. Shankar <ravi.v.shankar@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: ricardo.neri@intel.com
Link: http://lkml.kernel.org/r/1511233476-17088-1-git-send-email-ricardo.neri-calderon@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
