This patch makes acpi_init() exit early when ACPI is disabled.
This skips a DMI check that affects ACPI power management. The
DMI check prints a notice that is misleading when ACPI is disabled.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A number of things that shouldn't be exposed outside the ACPI core
were declared in include/acpi/acpi_drivers.h, where anybody can
see them. This patch moves those declarations to a new "internal.h"
inside drivers/acpi.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_early_init() was changed to over-write the cmdline param,
making it really inconvenient to set debug flags at boot-time.
Also,
This sets the default level to "info", which is what all the ACPI
drivers use. So to enable messages from drivers, you only have to
supply the "layer" (a.k.a. "component"). For non-"info" ACPI core
and ACPI interpreter messages, you have to supply both level and
layer masks, as before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When CONFIG_ACPI_DEBUG=y, the default acpi_dbg_layer and acpi_dbg_level
values built into the ACPI CA have some debug output enabled. We'd
rather be quiet unless the user actually specified the acpi.debug_level
argument.
This enables distros to ship with CONFIG_ACPI_DEBUG=y without
inundating users with debug output.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove CONFIG_ACPI_EC. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Per section 6.5.4 of the ACPI 3.0b specification,
OSPM must make Embedded Controller operation regions, accessed
via the Embedded Controllers described in ECDT, available before
executing any control method.
The ECDT table is optional, but if it is present, the above text
means that the EC it describes is a required part of the ACPI
subsystem, so CONFIG_ACPI_EC=n wouldn't make sense.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
According to ACPI spec when the status of some device is not present
but functional, the device is valid and the children of this device
should be enumerated. It means that the device should be added to
linux acpi device tree. But the device driver for this device should not
be loaded.
The detailed info can be found in the section 6.3.7 of ACPI 3.0b spec.
_STA may return bit 0 clear (not present) with bit 3 set (device is
functional). This case is used to indicate a valid device for which no
device driver should be loaded (for example, a bridge device.).
Children of this device may be present and valid. OS should continue
enumeration below a device whose _STA returns this bit combination
http://bugzilla.kernel.org/show_bug.cgi?id=3358
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add the DMI check to disable power check in the course of device power
transistion.
http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Maybe the incorrect power state is returned on the bogus bios, which
is different with the real power state. For example: the bios returns D0
state and the real power state is D3. OS expects to set the device to D0
state. In such case if OS uses the power state returned by the BIOS and
checks the device power state very strictly in power transition, the device
can't be transited to the correct power state.
So the boot option of "acpi.power_nocheck=1" is added to avoid checking
the device power in the course of device power transition.
http://bugzilla.kernel.org/show_bug.cgi?id=8049http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As of version 2.0, ACPI can return 64-bit integers. The current
acpi_evaluate_integer only supports 64-bit integers on 64-bit platforms.
Change the argument to take a pointer to an acpi_integer so we support
64-bit integers on all platforms.
lenb: replaced use of "acpi_integer" with "unsigned long long"
lenb: fixed bug in acpi_thermal_trips_update()
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
when there is no ECDT table and no _INI object for EC device, it will be
enabled before scanning ACPI device. But it is too late after the following
the commit is merged.
>commit 7752d5cfe3
> Author: Robert Hancock <hancockr@shaw.ca>
> Date: Fri Feb 15 01:27:20 2008 -0800
>x86: validate against acpi motherboard resources
After the above commit is merged, OS will check whether MCFG area is
reserved in ACPI motherboard resources by calling the function of
acpi_get_devices when there exists MCFG table. In the acpi_get_devices the _STA
object will be evaluated to check the status of the ACPI device. On some broken
BIOS the MYEC object of EC device is initialized as one, which indicates that
EC operation region is already accessible before enabling EC device.So on these
broken BIOS the EC operation region will be accessed in course of evaluating
the _STA object before enabling EC device, which causes that OS will print the
following warning messages:
>ACPI Error (evregion-0315): No handler for Region [EC__] (ffff88007f8145e8)
[EmbeddedControl] [20080609]
>ACPI Error (exfldio-0290): Region EmbeddedControl(3) has no handler [20080321]
>ACPI Error (psparse-0530): Method parse/execution failed [\_SB_.PCI0.SBRG.
EC__.BAT1._STA] (Node ffff81013fc17a00), AE_NOT_EXIST
>ACPI Error (uteval-0233): Method execution failed [\_SB_.PCI0.SBRG.EC__.BAT1.
_STA] (Node ffff81013fc17a00), AE_NOT_EXIST
Although the above warning message is harmless, it looks confusing.
So it is necessary to enable EC device as early as possible.Maybe it is
appropriate to enable it immediately after ACPI full initialization.
http://bugzilla.kernel.org/show_bug.cgi?id=11255http://bugzilla.kernel.org/show_bug.cgi?id=11374http://bugzilla.kernel.org/show_bug.cgi?id=11660
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
The battery driver already registers notification handler.
To avoid registering notification handler again,
introduce a notifier chain in global system notifier handler
and use it in dock driver.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
No longer needed; replaced mostly with u32, but also acpi_size
where a type that changes 32/64 bit on 32/64-bit platforms is
required.
v2: Fix a cast of a 32-bit int to a pointer in ACPI to avoid a compiler warning.
from David Howells
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
* Introduce function acpi_pm_device_sleep_wake() for enabling and
disabling the system wake-up capability of devices that are power
manageable by ACPI.
* Introduce function acpi_bus_can_wakeup() allowing other (dependent)
subsystems to check if ACPI is able to enable the system wake-up
capability of given device.
* Introduce callback .sleep_wake() in struct pci_platform_pm_ops and
for the ACPI PCI 'driver' make it use acpi_pm_device_sleep_wake().
* Introduce callback .can_wakeup() in struct pci_platform_pm_ops and
for the ACPI 'driver' make it use acpi_bus_can_wakeup().
* Move the PME# handlig code out of pci_enable_wake() and split it
into two functions, pci_pme_capable() and pci_pme_active(),
allowing the caller to check if given device is capable of
generating PME# from given power state and to enable/disable the
device's PME# functionality, respectively.
* Modify pci_enable_wake() to use the new ACPI callbacks and the new
PME#-related functions.
* Drop the generic .platform_enable_wakeup() callback that is not
used any more.
* Introduce device_set_wakeup_capable() that will set the
power.can_wakeup flag of given device.
* Rework PCI device PM initialization so that, if given device is
capable of generating wake-up events, either natively through the
PME# mechanism, or with the help of the platform, its
power.can_wakeup flag is set and its power.should_wakeup flag is
unset as appropriate.
* Make ACPI set the power.can_wakeup flag for devices found to be
wake-up capable by it.
* Make the ACPI wake-up code enable/disable GPEs for devices that
have the wakeup.flags.prepared flag set (which means that their
wake-up power has been enabled).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce function acpi_bus_power_manageable() allowing other
(dependent) subsystems to check if ACPI is able to power manage given
device. This may be useful, for example, for PCI device power
management.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This path adds validation of the MMCONFIG table against the ACPI reserved
motherboard resources. If the MMCONFIG table is found to be reserved in
ACPI, we don't bother checking the E820 table. The PCI Express firmware
spec apparently tells BIOS developers that reservation in ACPI is required
and E820 reservation is optional, so checking against ACPI first makes
sense. Many BIOSes don't reserve the MMCONFIG region in E820 even though
it is perfectly functional, the existing check needlessly disables MMCONFIG
in these cases.
In order to do this, MMCONFIG setup has been split into two phases. If PCI
configuration type 1 is not available then MMCONFIG is enabled early as
before. Otherwise, it is enabled later after the ACPI interpreter is
enabled, since we need to be able to execute control methods in order to
check the ACPI reserved resources. Presently this is just triggered off
the end of ACPI interpreter initialization.
There are a few other behavioral changes here:
- Validate all MMCONFIG configurations provided, not just the first one.
- Validate the entire required length of each configuration according to
the provided ending bus number is reserved, not just the minimum required
allocation.
- Validate that the area is reserved even if we read it from the chipset
directly and not from the MCFG table. This catches the case where the
BIOS didn't set the location properly in the chipset and has mapped it
over other things it shouldn't have.
This also cleans up the MMCONFIG initialization functions so that they
simply do nothing if MMCONFIG is not compiled in.
Based on an original patch by Rajesh Shah from Intel.
[akpm@linux-foundation.org: many fixes and cleanups]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@suse.de>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
List could have become empty after the unlocked check that was made earlier,
so check again inside the lock.
Should fix https://bugzilla.redhat.com/show_bug.cgi?id=427765
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Cc: <stable@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add function definition and extern variables to asm-x86/acpi.h.
All of these are used in bus.c in ifdef(CONFIG_X86) sections, so are
only added to the x86 include headers. boot.c already includes acpi.h
so no changes are needed there.
Fixes the following:
arch/x86/kernel/acpi/boot.c:83:4: warning: symbol 'acpi_sci_flags' was not declared. Should it be static?
arch/x86/kernel/acpi/boot.c:84:5: warning: symbol 'acpi_sci_override_gsi' was not declared. Should it be static?
arch/x86/kernel/acpi/boot.c:421:13: warning: symbol 'acpi_pic_sci_set_trigger' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Intel menlow driver needs to get the pointer of themal_zone_device
structure of an ACPI thermal zone.
Attach this to each ACPI thermal zone device object.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There is no firmware "subsystem" it's just a directory in /sys that
other portions of the kernel want to hook into. So make it a kobject
not a kset to help alivate anyone who tries to do some odd kset-like
things with this.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a kset here, a simple kobject will do just fine, so
dynamically create the kobject and use it.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a "default" ktype for a kset. We should set this
explicitly every time for each kset. This change is needed so that we
can make ksets dynamic, and cleans up one of the odd, undocumented
assumption that the kset/kobject/ktype model has.
This patch is based on a lot of help from Kay Sievers.
Nasty bug in the block code was found by Dave Young
<hidave.darkstar@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ACPI and APM used "pm_active" to guarantee that
they would not be simultaneously active.
But pm_active was recently moved under CONFIG_PM_LEGACY,
so that without CONFIG_PM_LEGACY, pm_active became a NOP --
allowing ACPI and APM to both be simultaneously enabled.
This caused unpredictable results, including boot hangs.
Further, the code under CONFIG_PM_LEGACY is scheduled
for removal.
So replace pm_active with pm_flags.
pm_flags depends only on CONFIG_PM,
which is present for both CONFIG_APM and CONFIG_ACPI.
http://bugzilla.kernel.org/show_bug.cgi?id=9194
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
force_power_state was used as a workaround for invalid cached
power state of the device. We do not cache power state, so no need for
workaround.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI may change power resource state behind our back, so don't
keep our local copy, which may not be valid.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (41 commits)
ACPICA: hw: Don't carry spinlock over suspend
ACPICA: hw: remove use_lock flag from acpi_hw_register_{read, write}
ACPI: cpuidle: port idle timer suspend/resume workaround to cpuidle
ACPI: clean up acpi_enter_sleep_state_prep
Hibernation: Make sure that ACPI is enabled in acpi_hibernation_finish
ACPI: suppress uninitialized var warning
cpuidle: consolidate 2.6.22 cpuidle branch into one patch
ACPI: thinkpad-acpi: skip blanks before the data when parsing sysfs
ACPI: AC: Add sysfs interface
ACPI: SBS: Add sysfs alarm
ACPI: SBS: Add ACPI_PROCFS around procfs handling code.
ACPI: SBS: Add support for power_supply class (and sysfs)
ACPI: SBS: Make SBS reads table-driven.
ACPI: SBS: Simplify data structures in SBS
ACPI: SBS: Split host controller (ACPI0001) from SBS driver (ACPI0002)
ACPI: EC: Add new query handler to list head.
ACPI: Add acpi_bus_generate_event4() function
ACPI: Battery: add sysfs alarm
ACPI: Battery: Add sysfs support
ACPI: Battery: Misc clean-ups, no functional changes
...
Fix up conflicts in drivers/misc/thinkpad_acpi.[ch] manually
A number of different drivers incorrect access the kobject name field
directly. This is not correct as the name might not be in the array.
Use the proper accessor function instead.
ACPI spec defines the sequence of IDE power on/off:
Powering down:
Call _GTM.
Power down drive (calls _PS3 method and turns off power planes).
Powering up:
Power up drive (calls _PS0 method if present and turns on power planes).
Call _STM passing info from _GTM (possibly modified), with ID data from
each drive.
Initialize the channel.
May modify the results of _GTF.
For each drive:
Call _GTF.
Execute task file (possibly modified).
This patch adds the missed _PS0/_PS3 methods call.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
acpi_bus_generate_event() takes two strings out of passed device object.
SBS needs to supply these strings directly.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Schedule /proc/acpi/event for removal in 6 months.
Re-name acpi_bus_generate_event() to acpi_bus_generate_proc_event()
to make sure there is no confusion that it is for /proc/acpi/event only.
Add CONFIG_ACPI_PROC_EVENT to allow removal of /proc/acpi/event.
There is no functional change if CONFIG_ACPI_PROC_EVENT=y
Signed-off-by: Len Brown <len.brown@intel.com>
The previous events patch added a netlink event for every
user of the legacy /proc/acpi/event interface.
However, some users of /proc/acpi/event are really input events,
and they already report their events via the input layer.
Introduce a new interface, acpi_bus_generate_netlink_event(),
which is explicitly called by devices that want to repoprt
events via netlink. This allows the input-like events
to opt-out of generating netlink events. In summary:
events that are sent via netlink:
ac/battery/sbs
thermal
processor
thinkpad_acpi dock/bay
events that are sent via input layer:
button
video hotkey
thinkpad_acpi hotkey
asus_acpi/asus-laptop hotkey
sonypi/sonylaptop
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Upon ACPI events, send an "acpi_event" via Generic Netlink.
This is in addition to /proc/acpi/event, which remains intact for now.
Thanks to Jamal for his great help.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Be explicit about what "device->status = 0x0F" really means.
syntax only.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
cosmetic only
Make "module name" actually match the file name.
Invoke with ';' as leaving it off confuses Lindent and gcc doesn't care.
Fix indentation where Lindent did get confused.
Signed-off-by: Len Brown <len.brown@intel.com>
late_initcall() is too late for acpi_sleep_init().
Call it directly from acpi_init code.
http://bugzilla.kernel.org/show_bug.cgi?id=7887
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Vladimir Lebedev <vladimir.p.lebedev@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Provide ACPI _PRT support for SN Altix systems.
The SN Altix platform does not conform to the
IOSAPIC IRQ routing model, so a new acpi_irq_model
(ACPI_IRQ_MODEL_PLATFORM) has been defined. The SN
platform specific code sets acpi_irq_model to
this new value, and keys off of it in acpi_register_gsi()
to avoid the iosapic code path.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
