It turns out that commit f9bd170a87
broke the cascade from XICS to i8259 on pSeries machines; specifically
we ended up not ever doing the EOI on the XICS for the cascade. The
result was that interrupts from the serial ports (and presumably any
other devices using ISA interrupts) didn't get through. This fixes
it and also simplifies the code, by doing the EOI on the XICS in the
xics_get_irq routine after reading and acking the interrupt on the
i8259.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some debug code wasn't properly removed from the initial 64k pages
patch, and while it's harmless, it's also slowing down significantly a
very hot code path, thus it should really be removed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous commit will use the page-at-a-time hypervisor call for
setting up IOMMU entries when we are using 64k pages and setting up
one 64k page, even though that means 16 calls to the hypervisor, since
the hypervisor still works on 4k pages. This optimizes this case by
using the multi-page IOMMU setup hypervisor call instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Must adjust tcenum and npages by TCE_PAGE_FACTOR to convert between
64KB pages and TCE (4K) pages. (This is done in other places, except
for this one location.)
Signed-off-by: Michal Ostrowski <mostrows at watson ibm com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Email address update, changing old work address to personal (permanent)
one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pseries_dedicated_idle() was using __get_tb which used to be defined
in asm/delay.h. Change it to use get_tb from asm/time.h, which is
in fact exactly the same thing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the kernel supports both G5 and pSeries, and CONFIG_EEH is enabled,
eeh_init() is (quite reasonably) never called when we boot on a G5. Yet
eeh_check_failure() still gets called. We should avoid doing that if
!eeh_subsystem_enabled.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also deletes files in arch/ppc64 that are no longer used now that
we don't compile with ARCH=ppc64 any more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a ppc_md member called cpu_irq_down, which disables IRQs
for the cpu in question. The only caller of cpu_irq_down is the kexec code.
On pSeries we need to do more than just teardown IRQs at kexec time, so rename
the ppc_md member to kexec_cpu_down and expand it. The pSeries code needs to
know, and other platforms might too, whether we're doing a crash shutdown (ie.
panicking) or a regular kexec, so add a flag for that.
The pSeries implementation of kexec_cpu_down does an unregister VPA call, which
tells the Hypervisor to stop writing stuff into our pacas. Without this we can
get weird memory corruption bugs when we kexec, caused by the Hypervisor
writing into the first kernel's pacas which happens to be somewhere interesting
in the second kernel's memory.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We needed the VDSO symbols in the arch/ppc asm-offsets.c, and there
were a few usages of _systemcfg still left lying around.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have been printing the raw ppc64_firmware_features during boot. Since
we can work it out from the device tree, lets remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
17-eeh-slot-marking-bug.patch
A device that experiences a PCI outage may be just one deivce out
of many that was affected. In order to avoid repeated reports of
a failure, the entire tree of affected devices should be marked
as failed. This patch marks up the entire tree.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
phbs_remap_io(), which maps the PCI IO space into the kernel virtual space,
is called too early on powermac, and thus doesn't work.
This fixes it by removing the call from all platforms and putting it back
into the ppc64 common code where it belongs, after the actual probing of
the bus.
That means that before that call, only the ISA IO space (if any) is mapped,
any PIO access (from quirks for example) will fail. This happens not to be
a problem for now, but we'll have to rework that code if it becomes one in
the future.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges platform codes. systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32. Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
scanlog.c is only compiled on pSeries. Thus, this patch moves it to
platforms/pseries.
Built and booted on pSeries LPAR (ARCH=powerpc and ARCH=ppc64). Built
for iSeries (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
14-eeh-device-bar-save.patch
After a PCI device has been resest, the device BAR's and other config
space info must be restored to the same state as they were in when
the firmware first handed us this device. This will allow the
PCI device driver, when restarted, to correctly recognize and set up
the device.
Tis patch saves the device config space as early as reasonable after
the firmware has handed over the device. Te state resore funcion
is inteded for use by the EEH recovery routines.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
13-eeh-recovery-support-routines.patch
EEH Recovery support routines
This patch adds routines required to help drive the recovery of
EEH-frozen slots. The main function is to drive the PCI #RST
signal line high for a qurter of a second, and then allow for
a second & a half of settle time.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
12-eeh-event-dispatcher.patch
ppc64: EEH Recovery dispatcher thread
This patch adds a mechanism to create recovery threads when an
EEH event is received. Since an EEH freeze state may be detected
within an interrupt context, we need to get out of the interrupt
context before starting recovery. This dispatcher does this in
two steps: first, it uses a workqueue to get out, and then
lanuches a kernel thread, so that the recovery routine can
sleep for exteded periods without upseting the keventd.
A kernel thread is created with each EEH event, rather than
having one long-running daemon started at boot time. This is
because it is anticipated that EEH events will be very rare
(very very rare, ideally) and so its pointless to cluter the
process tables with a daemon that will almost never run.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
11-eeh-move-to-powerpc.patch
Move arch/ppc64/kernel/eeh.c to arch//powerpc/platforms/pseries/eeh.c
No other changes (except for Makefile to build it)
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use __do_IRQ instead. The only difference is that every controller
is now assumed to have an end() routine (only xics_8259 did not).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This is the arch/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in arch/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define ppc_md.set_dabr for both 32 + 64 bit. Cleanup the implementation for
pSeries also, it was needlessly complex. Now we just do two firmware tests at
setup time, and use one of two functions, rather than using one function and
testing on every call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mostly this involves adding #include <asm/smp.h>, since that defines
things like boot_cpuid[_phys] and [gs]et_hard_smp_processor_id, which
are SMP-related but still needed on UP. This incorporates fixes
posted by Olof Johansson and Heikki Lindholm.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ancient ppcdebug/PPCDBG mechanism is now only used in two places.
First, in the hash setup code, one of the bits allows the size of the
hash table to be reduced by a factor of 8 - which would be better
accomplished with a command line option for that purpose. The other
was a bunch of bus walking related messages in the iSeries code, which
would seem to be insufficient reason to keep the mechanism.
This patch removes the last traces of this mechanism.
Built and booted on iSeries and pSeries POWER5 LPAR (ARCH=powerpc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel
base page size to 64K. The resulting kernel still boots on any
hardware. On current machines with 4K pages support only, the kernel
will maintain 16 "subpages" for each 64K page transparently.
Note that while real 64K capable HW has been tested, the current patch
will not enable it yet as such hardware is not released yet, and I'm
still verifying with the firmware architects the proper to get the
information from the newer hypervisors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
register_vpa() doesn't actually do a VPA register call it just uses the flags
you pass it, so rename it to vpa_call() to be clearer.
We can then define register_vpa() and unregister_vpa() which are both simple
wrappers around vpa_call(). (we'll need unregister_vpa() for kexec soon)
We can then cleanup vpa_init(), and because vpa_init() is only called from
platforms/pseries we remove the definition in asm-ppc64/smp.h.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
The extraction of PCI stuff from struct device_node left some false
assumptions in notifier code. As a result, dynamic add crashes when
non-PCI nodes are added. This patch fixes these assumptions.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move plpar_wrappers.h into arch/powerpc/platforms/pseries, fixup white space,
and update callers.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Move pSeries specific code in set_dabr() into a ppc_md function, this will
allow us to keep plpar_wrappers.h private to platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
This moves rtas-proc.c and rtas_flash.c into arch/powerpc/kernel, since
cell wants them as well as pseries (and chrp can use rtas-proc.c too,
at least in principle). rtas_fw.c is gone, with its bits moved into
rtas_flash.c and rtas.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A recent commit that removed rtas-fw.h and moved its contents to
include/asm-powerpc/rtas.h forgot to also remove the inclusion of
it in arch/powerpc/platforms/pseries/setup.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cell uses the same code as pSeries for flashing the firmware
through rtas, so the implementation should not be part of
platforms/pseries.
Put it into arch/powerpc/kernel instead.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves the XICS interrupt controller code into the
platforms/pseries directory, since it only appears on pSeries
machines. If it ever appears on some other machine we can move it to
sysdev, although xics.c itself will need a bunch of changes in that
case to remove pSeries specific assumptions.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits arch/ppc64/kernel/rtas.c into arch/powerpc/kernel/rtas.c,
which contains generic RTAS functions useful on any CHRP platform,
and arch/powerpc/platforms/pseries/rtas-fw.[ch], which contain
some pSeries-specific firmware flashing bits. The parts of rtas.c
that are to do with pSeries-specific error logging are protected
by a new CONFIG_RTAS_ERROR_LOGGING symbol. The inclusion of rtas.o
is controlled by the CONFIG_PPC_RTAS symbol, and the relevant
platforms select that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the parameters for i8259_init so that it takes two
parameters: a physical address for generating an interrupt
acknowledge cycle, and an interrupt number offset. i8259_init
now sets the irq_desc[] for its interrupts; all the callers
were doing this, and that code is gone now. This also defines
a CONFIG_PPC_I8259 symbol to select i8259.o for inclusion, and
makes the platforms that need it select that symbol.
Signed-off-by: Paul Mackerras <paulus@samba.org>
ras.o is only built for CONFIG_PPC_PSERIES, so move it into
arch/powerpc/platforms/pseries. Update Makefiles to suit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This way they get done in one place for all platforms, and it is
more consistent with what ppc32 does.
Signed-off-by: Paul Mackerras <paulus@samba.org>
I missed a few places where ppc code was still assuming that the
ppc_md.show_[per]cpuinfo functions returned int.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A few things change for consistency between ppc32 and ppc64:
idle functions return void; *_get_boot_time functions return
unsigned long (i.e. time_t) rather than filling in a struct rtc_time
(since that's useful to the callers and easier for pmac to
generate); *_get_rtc_time and *_set_rtc_time functions take
a struct rtc_time; irq_canonicalize is gone; nvram_sync returns
void.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
