Pull MIPS updates from Ralf Baechle:
- three fixes for 3.15 that didn't make it in time
- limited Octeon 3 support.
- paravirtualization support
- improvment to platform support for Netlogix SOCs.
- add support for powering down the Malta eval board in software
- add many instructions to the in-kernel microassembler.
- add support for the BPF JIT.
- minor cleanups of the BCM47xx code.
- large cleanup of math emu code resulting in significant code size
reduction, better readability of the code and more accurate
emulation.
- improvments to the MIPS CPS code.
- support C3 power status for the R4k count/compare clock device.
- improvments to the GIO support for older SGI workstations.
- increase number of supported CPUs to 256; this can be reached on
certain embedded multithreaded ccNUMA configurations.
- various small cleanups, updates and fixes
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (173 commits)
MIPS: IP22/IP28: Improve GIO support
MIPS: Octeon: Add twsi interrupt initialization for OCTEON 3XXX, 5XXX, 63XX
DEC: Document the R4k MB ASIC mini interrupt controller
DEC: Add self as the maintainer
MIPS: Add microMIPS MSA support.
MIPS: Replace calls to obsolete strict_strto call with kstrto* equivalents.
MIPS: Replace obsolete strict_strto call with kstrto
MIPS: BFP: Simplify code slightly.
MIPS: Call find_vma with the mmap_sem held
MIPS: Fix 'write_msa_##' inline macro.
MIPS: Fix MSA toolchain support detection.
mips: Update the email address of Geert Uytterhoeven
MIPS: Add minimal defconfig for mips_paravirt
MIPS: Enable build for new system 'paravirt'
MIPS: paravirt: Add pci controller for virtio
MIPS: Add code for new system 'paravirt'
MIPS: Add functions for hypervisor call
MIPS: OCTEON: Add OCTEON3 to __get_cpu_type
MIPS: Add function get_ebase_cpunum
MIPS: Add minimal support for OCTEON3 to c-r4k.c
...
The XLP9XX SoC has an on-chip SATA controller with two ports. Add
ahci-init-xlp2.c to initialize the controller, setup the glue logic
registers, fixup PCI quirks and setup interrupt ack logic.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6913/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
XLP3XX includes an on-chip SATA controller with 4 ports. The
controller needs glue logic initialization and PCI fixup before
it can be used with the standard AHCI driver.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the XLP5XX processor which is an 8 core variant of the
XLP9XX. Add XLP5XX cases to code which earlier handled XLP9XX.
Signed-off-by: Yonghong Song <ysong@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6871/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Calculate XLP 9XX and 2XX core frequency from the per-core PLL. This
should give the correct value for all board configurations.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6870/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update PIC frequency calculation for XLP9XX and 2XX processors using
the correct PLL registers. This should work for all possible board
configurations.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6876/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the compatible property to the PIC entry. Also fix up the nodename
to use the correct address.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6869/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add IRQ to IRT (PIC interupt table index) mapping for SATA, GPIO, NAND
and SPI interfaces on the XLP SoC. Fix offsets for few blocks and add
device IDs for a few blocks.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6911/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ELPA bit needs to be set in the PAGEGRAIN register to enable
access to >64GB physical address. Update reset.S to do this from
every hardware thread.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update thread wakeup function to use scratch registers for saving SP and
RA. Move the register restore code needed for thread 0 to the calling
function. This reduces the size of code copied to the reset vector.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6910/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing was using the method and there isn't any need for this hook. This
leaves smp_cpus_done() empty for the moment.
As suggested by Paul Bolle <pebolle@tiscali.nl>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unify the various architectures __dtb_start and __dtb_end definitions
moving them into of_fdt.h.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-metag@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux@lists.openrisc.net
Cc: linux-xtensa@linux-xtensa.org
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
The existing code is buggy because built-in DTBs are in init memory.
It is also broken because the reserved bootmem was then freed after
unflattening, but the unflattened tree points to data in the flat tree.
Fix this by using the unflatten_and_copy_device_tree function.
This removes all accesses to FDT header data by the arch code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Tested-by: Grant Likely <grant.likely@linaro.org>
Pull MIPS updates from Ralf Baechle:
"The most notable new addition inside this pull request is the support
for MIPS's latest and greatest core called "inter/proAptiv". The
patch series describes this core as follows.
"The interAptiv is a power-efficient multi-core microprocessor
for use in system-on-chip (SoC) applications. The interAptiv combines
a multi-threading pipeline with a coherence manager to deliver improved
computational throughput and power efficiency. The interAptiv can
contain one to four MIPS32R3 interAptiv cores, system level
coherence manager with L2 cache, optional coherent I/O port,
and optional floating point unit."
The platform specific patches touch all 3 Broadcom families. It adds
support for the new Broadcom/Netlogix XLP9xx Soc, building a common
BCM63XX SMP kernel for all BCM63XX SoCs regardless of core type/count
and full gpio button/led descriptions for BCM47xx.
The rest of the series are cleanups and bug fixes that are MIPS
generic and consist largely of changes that Imgtec/MIPS had published
in their linux-mti-3.10.git stable tree. Random other cleanups and
patches preparing code to be merged in 3.15"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
mips: select ARCH_MIGHT_HAVE_PC_SERIO
mips: delete non-required instances of include <linux/init.h>
MIPS: KVM: remove shadow_tlb code
MIPS: KVM: use common EHINV aware UNIQUE_ENTRYHI
mips/ide: flush dcache also if icache does not snoop dcache
MIPS: BCM47XX: fix position of cpu_wait disabling
MIPS: BCM63XX: select correct MIPS_L1_CACHE_SHIFT value
MIPS: update MIPS_L1_CACHE_SHIFT based on MIPS_L1_CACHE_SHIFT_<N>
MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>
MIPS: ZBOOT: gather string functions into string.c
arch/mips/pci: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
bcma: gpio: don't cast u32 to unsigned long
ssb: gpio: add own IRQ domain
MIPS: BCM47XX: fix sparse warnings in board.c
MIPS: BCM47XX: add board detection for Linksys WRT54GS V1
MIPS: BCM47XX: fix detection for some boards
MIPS: BCM47XX: Enable buttons support on SSB
MIPS: BCM47XX: Convert WNDR4500 to new syntax
MIPS: BCM47XX: Use "timer" trigger for status LEDs
...
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6320/
Move wakeup to after early console. This will allow us to display error
messages when cores are not woken up. Also reduce the wait time for core
to come up.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6303/
The early serial code is not needed because we already have early
printk support provided by common/earlycons.c
This change also fixes the following build error that occurs when
CONFIG_SERIAL_8250 is not configured for Netlogic XLR boards:
arch/mips/built-in.o: In function `nlm_early_serial_setup':
setup.c:(.init.text+0x274): undefined reference to `early_serial_setup'
make: *** [vmlinux] Error 1
Reported-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6083/
Add a default device tree fie for XLP9XX boards, and add code to use
this device tree if no DTB is passed to the kernel.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6287/
Support for adding legacy IRQ domain for XLP9XX. The node id of the
PIC has to be calulated differently for XLP9XX.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6286/
XLP9XX has a USB 3.0 controller on-chip with 2 xHCI ports. The USB
block is similar to the one on XLP2XX, so update usb-init-xlp2.c
to handle XLP9XX as well.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6285/
Add PCI support for Netlogic XLP9XX. The PCI registers and
SoC bus numbers have changed in XLP9XX.
Also skip a few (bus,dev,fn) combinations which have issues when
read.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6284/
XLP9XX has 20 cores per node, opposed to 8 on earlier XLP8XX.
Update code that calculates node id from cpu id to handle this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6283/
Update bridge code. Add code to the XLP9XX registers for DRAM
size, limit and node when running on XLPXX
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6282/
Update IO offset of the early console UART.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6281/
Add the SYS block registers for XLP9XX, most of them have changed.
The wakeup sequence has been updated to set the coherent mode from
the main thread rather than the woken up thread.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6280/
Functions for the XLP9XX interrupt table entry format and other PIC
register changes.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6279/
Most IO block offsets have changed in XLP9XX. Update iomap.h to add the
new addresses of different SoC blocks like PIC, SYS, UART etc. that are
needed by the base code.
On XLP9xx, the SoC blocks of other nodes are seen on a PCI bus
corresponding to the node. Update iomap code to reflect this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6277/
Adds processor ID of XLP 9XX to asm/cpu.h. Update netlogic/xlp-hal/xlp.h
to add cpu_is_xlp9xx() and to update cpu_is_xlpii() to support XLP 9XX.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6274/
Use the FUSE register to get the list of active cores in the CPU
instead of using the CPU reset register, this is the recommended
method.
Also add code to mask the coremask with the default number of cores
for each processor series.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6275/
On XLPII CPUs, the L1D cache has to be flushed with regular cache
operations before enabling threads in a core.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6276/
No change in logic, the changes are:
* cleanup some whitespace and comments
* remove confusing argument of SYS_CPU_COHERENT_BASE macro
* make the numerical labels in macros consistent
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6273/
Add MSI chip and MSIX chip definitions.
For MSI, we map the link interrupt to a MSI link IRQ which will
do a second level of dispatch based on the MSI status register.
The MSI chip definitions use the MSI enable register to enable
and disable the MSI irqs.
For MSI-X, we split the 32 available MSI-X vectors across the
four PCIe links (8 each). These PIC interrupts generate an IRQ
per link which uses a second level dispatch as well.
The MSI-X chip definition uses the standard functions to enable
and disable interrupts.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6270/
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
The early_init_devtree() API was removed in linux-next for 3.13 with
commit "mips: use early_init_dt_scan". This causes Netlogic XLP compile
to fail:
arch/mips/netlogic/xlp/setup.c:101: undefined reference to `early_init_devtree'
Add xlp_early_init_devtree() which uses the __dt_setup_arch() to
handle early device tree related initialization to fix this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Panic() is going to add a \n itself and it's annoying if a panic message rolls
of the screen on a device with no scrollback.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace hardcoded CP0 PRId and CP1 FPIR register access masks throughout.
The change does not touch places that use shifted or partial masks.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a default built-in device tree for XLP2xx SoC. The new file
xlp_fvp.dts has updated entries for I2C and memory.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5705/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add USB intialization code to handle the new XLP2XX USB 3.0 block.
This adds xlp/usb-init-xlp2.c to initialize the XLP2XX USB glue-logic
for XHCI and EHCI. Interrupt and IO offset code in xlp-hal/iomap.h
and xlp/nlm_hal.c is also updated for the new USB block.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5744/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
XLP2xx has a new I2C controller which has 4 buses connected to
it. Update the IO offset and IRQ mapping code to reflect this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On XLP2xx, wakeup code does not need to enable clock on the core.
Update xlp/wakeup.c to handle this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add code to calculate the CPU and PIC frequency for XLP2XX SoCs.
Since the PIC frequency on XLP2XX can be configured, add a new macro
pic_timer_freq() to be used in netlogic/common/time.c.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5701/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The config7/config4 register has to be written on all the threads.
This does not cause any problems in XLP, but is needed for XLPII
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
XLP2XX is first in the series of 28nm XLPII processors.
The changes are to:
* Add processor ID for XLP2XX to asm/cpu.h and kernel/cpu-probe.c.
* Add a cpu_is_xlpii() function to check for XLPII processors.
* Update xlp_mmu_init() to use config4 to enable extended TLB.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Do not pass a memory section in the built-in DTB, and let the
boot code use the values from the DRAM BARs.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5699/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Read the memory from the Bridge DRAM BARs, if it is not passed in
from the device tree. This will allow us to remove memory configuration
from built in device trees.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5743/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes for 3.11. Half of then is for Netlogic the remainder
touches things across arch/mips.
Nothing really dramatic and by rc1 standards MIPS will be in fairly
good shape with this applied. Tested by building all MIPS defconfigs
of which with this pull request four platforms won't build. And yes,
it boots also on my favorite test systems"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: kvm: Kconfig: Drop HAVE_KVM dependency from VIRTUALIZATION
MIPS: Octeon: Fix DT pruning bug with pip ports
MIPS: KVM: Mark KVM_GUEST (T&E KVM) as BROKEN_ON_SMP
MIPS: tlbex: fix broken build in v3.11-rc1
MIPS: Netlogic: Add XLP PIC irqdomain
MIPS: Netlogic: Fix USB block's coherent DMA mask
MIPS: tlbex: Fix typo in r3000 tlb store handler
MIPS: BMIPS: Fix thinko to release slave TP from reset
MIPS: Delete dead invocation of exception_exit().
Add a legacy irq domain for the XLP PIC interrupts. This will be used
when interrupts are assigned from the device tree. This change is required
after commit c5cdc67 "irqdomain: Remove temporary MIPS workaround code".
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Jayachandran C <jchandra@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/5597/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The on-chip USB controller on Netlogic XLP does not suppport
DMA beyond 32-bit physical address. Set the coherent_dma_mask
of the USB in its PCI fixup to support this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5596/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 3747069b25e419f6b51395f48127e9812abc3596 upstream.
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
Here, we remove all the MIPS __cpuinit from C code and __CPUINIT
from asm files. MIPS is interesting in this respect, because there
are also uasm users hiding behind their own renamed versions of the
__cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
[ralf@linux-mips.org: Folded in Paul's followup fix.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5494/
Patchwork: https://patchwork.linux-mips.org/patch/5495/
Patchwork: https://patchwork.linux-mips.org/patch/5509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix an issue in plat_irq_dispatch due to which it can call do_IRQ
with a PIC irq that is not mapped.
When a per-cpu interrupt and a PIC interrupt are both active, the
check 'eirr & PERCPU_IRQ_MASK' will be true, but the interrupt in 'i'
will be the number of the PIC interrupt. In this case, we will call
do_IRQ on the PIC interrupt without mapping it with nlm_irq_to_xirq().
Fix this by using __ffs64 instead of __ilog2_u64 and using the
interrupt number instead of mask to identify per-cpu interrupts.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5432/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XLPs in production do not need these workarounds. Remove the code and
the associated ifdef.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5430/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a cache error found in stress test, caused by the prefetch instruction
going beyond valid memory when acessing the last page of a region. Add
the pref_backup logic similar to XLR in XLP too.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5431/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Earlier we just waited for the first thread of the CPU to come online
before proceeding to wake up others. Update it to wait for all the CPUs
in the core. This will be useful when the boot-up is slow, like while
debugging or when running in a simulator.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5429/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix an issue in the reset code. Since this code is copied to the
reset vector, using 'j' for looping is not correct. Use relative
branch 'b'.
Update the usage of 'j' in smpboot.S to be consistent although it
is not a bug there.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5427/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the nlm_cpu_ready[] array used by the cpu wakeup code to the
boot area, along with rest of the boot parameter code.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5425/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This moves the calculation and casting needed to access the CPU initialization
data to a function nlm_get_boot_data()
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5426/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The core initialization and reset vector setup needs to be done
even when booting uniprocessor. Move this code from smp.c to setup.c
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5428/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The reset and core initialization code should be available for
uniprocessor as well. This changes is just to take out the code
into a different file, without any change to the logic.
The change for uniprocessor initialization code is in a later patch.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5423/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Create new flle arch/mips/netlogic/xlp/dt.c and move the device
tree related code there.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5422/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add COP2 register state structure and functions for Netlogic XLP. The
RX and TX buffers and status registers are to be saved. Since the
registers are 64-bit, do the implementation in inline assembly which
works on both 32-bit and 64-bit kernels.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: ddaney.cavm@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/5413/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rename macro nlm_cop2_enable() to nlm_cop2_enable_irqsave() and the macro
nlm_cop2_restore to nlm_cop2_disable_irqrestore(). The new names will
reflect the functionality better, and will make nlm_cop2_restore()
available to be used later in COP2 save/restore patch.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: ddaney.cavm@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/5412/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sel argument os nlm_read_c2_status() was not used and the macro
returned the sel 0 in all cases. Fix this by defining two macros:
nlm_read_c2_status0() and nlm_read_c2_status1() to return the two
status registers.
Add functions to write to the status registers as well.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: ddaney.cavm@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/5414/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add SWIOTLB config option and related files to Netlogic platform.
Some XLP SoC components like the SD/MMC interface cannot do DMA beyond
32-bit physical address. The SD/MMC driver can use memory outside this
range for IO, to support this we have to add bounce buffers implemented
by SWIOTLB.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/5410/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The definitions are not used anywhere else, and merging it will
make adding the new USB definitions for XLPII series easier.
While there, cleanup some whitespace in usb-init.c. There is no
change to logic due to this commit.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5027/
Acked-by: John Crispin <blogic@openwrt.org>
This enables us to have a default device tree per SoC family to be built
into the kernel. The default device tree for XLP3xx has been added as part
of this change. Later this can be used to provide support default boards
for XLP2xx and XLP9xx SoCs.
Kconfig options are provided for each default device tree so that just the
needed ones can be selected to be built into the kernel.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5023/
Acked-by: John Crispin <blogic@openwrt.org>
The index for a device interrupt in the PIC interrupt routing table
changes for different chips in the XLP family. Avoid using the fixed
entries and derive the index value from the SoC device header.
Add workarounds for some devices which do not report the IRT index
correctly.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5025/
Acked-by: John Crispin <blogic@openwrt.org>
Use standard function to print cpumask. Also fixup the name of the
variable used and make it static.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5024/
Acked-by: John Crispin <blogic@openwrt.org>
On multi-chip boards, the first core on slave SoCs may take much
more time to wakeup. Add code to wait for the core to come up before
proceeding with the rest of the boot up.
Update xlp_wakeup_core to also skip the boot node and the boot CPU
initialization which is already complete.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4783/
Signed-off-by: John Crispin <blogic@openwrt.org>
Doing calibrate delay on a hardware thread will be inaccurate since
it depends on the load on other threads in the core. It will also
slow down the boot process when done for 128 hardware threads. Switch
to a pre-computed loops per jiffy based on the core frequency. The
value is computed based on the core frequency and roughly matches the
value calculated by calibrate_delay().
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4791/
Signed-off-by: John Crispin <blogic@openwrt.org>
The XLR/XLS/XLP PIC has a 8 countdown timers which run at the PIC
frequencey. One of these can be used as a clocksource to provide
timestamps that is common across cores. This can be used in place
of the count/compare clocksource which is per-CPU.
On XLR/XLS PIC registers are 32-bit, so we just use the lower 32-bits
of the PIC counter. On XLP, the whole 64-bit can be used.
Provide common macros and functions for PIC timer registers on XLR/XLS
and XLP, and use them to register a PIC clocksource.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4786/
Signed-off-by: John Crispin <blogic@openwrt.org>
Since we now use r4k cache code for Netlogic XLP, it is
better to split L1 icache among the active threads, so that
threads won't step on each other while flushing icache.
The L1 dcache is already split among the threads in the core.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4787/
Signed-off-by: John Crispin <blogic@openwrt.org>
Provide functions ack_c0_eirr(), set_c0_eimr(), clear_c0_eimr()
and read_c0_eirr_and_eimr() that do the EIMR and EIRR operations
and update the interrupt handling code to use these functions.
Also, use the EIMR register functions to mask interrupts in the
irq code.
The 64-bit interrupt request and mask registers (EIRR and EIMR) are
accessed when the interrupts are off, and the common operations are
to set or clear a bit in these registers. Using the 64-bit c0 access
functions for these operations is not optimal in 32-bit, because it
will disable/restore interrupts and split/join the 64-bit value during
each register access.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4790/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add support for XLS6xx CPUs to the Fast Message Network (FMN)
configuration.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4785/
Signed-off-by: John Crispin <blogic@openwrt.org>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The commit 2a37b1a "MIPS: Netlogic: Move from u32 cpumask to cpumask_t"
breaks uniprocessor compilation on XLR with:
arch/mips/netlogic/xlr/setup.c: In function 'prom_init':
arch/mips/netlogic/xlr/setup.c:196:6: error: unused variable 'i'
Fix by defining 'i' only when CONFIG_SMP is defined.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4760/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers to
all work together nicer, which was a reduction in overall code. We also
deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a nice
thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhIYACgkQMUfUDdst+yk9gACgsZYgMtbrqdbhbjbYkfO7nYkB
iegAoIvj3qwe33TbZ8OJnIkaWcMiT8CW
=u6Bf
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers
to all work together nicer, which was a reduction in overall code. We
also deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a
nice thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (228 commits)
USB: mark uas driver as BROKEN
xhci: Add Lynx Point LP to list of Intel switchable hosts
uwb: fix uwb_dev_unlock() missed at an error path in uwb_rc_cmd_async()
USB: ftdi_sio: Add support for Newport AGILIS motor drivers
MAINTAINERS: remove drivers/block/ub.c
USB: chipidea: fix use after free bug
ezusb: add dependency to USB
usb: ftdi_sio: fixup BeagleBone A5+ quirk
USB: cp210x: add Virtenio Preon32 device id
usb: storage: remove redundant memset() in usb_probe_stor1()
USB: option: blacklist network interface on Huawei E173
USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue
USB: add new zte 3g-dongle's pid to option.c
USB: opticon: switch to generic read implementation
USB: opticon: refactor reab-urb processing
USB: opticon: use usb-serial bulk-in urb
USB: opticon: increase bulk-in size
USB: opticon: use port as urb context
USB: opticon: pass port to get_serial_info
USB: opticon: make private data port specific
...
All architectures that use cmd_dtc do so in almost the same way. Create
a central build rule to avoid duplication. The one difference is that
most current uses of dtc build $(obj)/%.dtb from $(src)/dts/%.dts rather
than building the .dtb in the same directory as the .dts file. This
difference will be eliminated arch-by-arch in future patches.
MIPS is the exception here; it already uses the exact same rule as the
new common rule, so the duplicate is removed in this patch to avoid any
conflict. arch/mips changes courtesy of Ralf Baechle.
Update Documentation/kbuild to remove the explicit call to cmd_dtc from
the example, now that the rule exists in a centralized location.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Cc: Mark Salter <msalter@redhat.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
On XLR/XLS, the cpu cores communicate with fast on-chip devices
(e.g. network accelerator, security engine etc.) using the Fast
Messaging Network(FMN). The FMN queues and credits needs to be
configured and intialized before it can be used.
The co-processor 2 on XLR/XLS CPU cores has registers for FMN access,
and the XLR/XLS has custom instructions for sending and loading
messages. The FMN can deliver also per-cpu interrupts when messages
are available at the CPU.
This patch adds FMN initialization, adds interrupt setup and handling,
and also provides support for sending and receiving FMN messages.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4468
Signed-off-by: John Crispin <blogic@openwrt.org>
Create struct nlm_pic_irq for interrupts handled by the PIC.
This simplifies IRQ handling for multi-SoC as well as
the single SoC cases. Also split the setup of percpu and PIC
interrupts so that we can configure the PIC interrupts for
every node.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4467
Signed-off-by: John Crispin <blogic@openwrt.org>
There can be 1, 2 or 4 SoCs(nodes) in a multi-chip XLP board. Add an
option for multi-chip boards in case of XLP, and make the number of
nodes configurable.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4470
Signed-off-by: John Crispin <blogic@openwrt.org>
Upto 4 Netlogic XLP SoCs can be connected over ICI links to form a
coherent multi-node system. Each SoC has its own set of on-chip
devices including PIC. To support this, add a per SoC stucture and
use it for the PIC and SYS block addresses instead of using global
variables.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4469
Signed-off-by: John Crispin <blogic@openwrt.org>
Initial code to support more than 32 cpus. The platform CPU mask
is updated from 32-bit mask to cpumask_t. Convert places that use
cpu_/cpus_ functions to use cpumask_* functions.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4464
Signed-off-by: John Crispin <blogic@openwrt.org>
The cpuid was not passed into early_init_secondary even though the
comment indicated that it will be. Fix this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4458
Signed-off-by: John Crispin <blogic@openwrt.org>
At this point early printk is available, so debugging device tree
issues is easier.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4460
Signed-off-by: John Crispin <blogic@openwrt.org>
Enable Speculative Unmap Enable bit, which will enable speculative L2
cache requests for unmapped memory. This should give better performance
for kernel code/data which is in KSEG0
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4461
Signed-off-by: John Crispin <blogic@openwrt.org>
The OHCI platform driver is suitable for use by the Netlogic XLR platform
so use this driver instead of the OHCI XLS platform driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EHCI platform driver is suitable for use by the Netlogic XLR platform
since there is nothing specific that the EHCI XLR platform driver does.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide a config option to embed a device tree for XLP evaluation
boards. This DTB will be used if the firmware does not pass in a
device tree pointer.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4103/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add the serial ports to the device tree and remove the platform
code for adding them.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4098/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add a basic DTS file netlogic/dts/nlm_xlp.dts which contains
memory, i2c devices, NOR flash and command line arguments.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Patchwork: http://patchwork.linux-mips.org/patch/4100/
Signed-off-by: John Crispin <blogic@openwrt.org>
