Bug noted by Pieter Palmers: Isochronous transmit tasklets were
scheduled on isochronous receive events, in addition to the proper
isochronous receive tasklets.
http://marc.info/?l=linux1394-devel&m=119783196222802
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch speeds up sbp2 a little bit --- but more importantly, it
brings the behavior of sbp2 and fw-sbp2 closer to each other. Like
fw-sbp2, sbp2 now does not limit the size of single transfers to 255
sectors anymore, unless told so by a blacklist flag or by module load
parameters.
Only very old bridge chips have been known to need the 255 sectors
limit, and we have got one such chip in our hardwired blacklist. There
certainly is a danger that more bridges need that limit; but I prefer to
have this issue present in both fw-sbp2 and sbp2 rather than just one of
them.
An OXUF922 with 400GB 7200RPM disk on an S400 controller is sped up by
this patch from 22.9 to 23.5 MB/s according to hdparm. The same effect
could be achieved before by setting a higher max_sectors module
parameter. On buses which use 1394b beta mode, sbp2 and fw-sbp2 will
now achieve virtually the same bandwidth. Fw-sbp2 only remains faster
on 1394a buses due to fw-core's gap count optimization.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Convert ieee1394 from nopage to fault.
Remove redundant vma range checks (correct resource range check is retained).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Replace sg->length by sg_dma_len(sg). Rename a variable for shorter
line lengths and eliminate some superfluous local variables.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch adds a new configuration option, which adds support for a new
early_param which gets checked in arch/x86/kernel/setup_{32,64}.c:setup_arch()
to decide wether OHCI-1394 FireWire controllers should be initialized and
enabled for physical DMA access to allow remote debugging of early problems
like issues ACPI or other subsystems which are executed very early.
If the config option is not enabled, no code is changed, and if the boot
paramenter is not given, no new code is executed, and independent of that,
all new code is freed after boot, so the config option can be even enabled
in standard, non-debug kernels.
With specialized tools, it is then possible to get debugging information
from machines which have no serial ports (notebooks) such as the printk
buffer contents, or any data which can be referenced from global pointers,
if it is stored below the 4GB limit and even memory dumps of of the physical
RAM region below the 4GB limit can be taken without any cooperation from the
CPU of the host, so the machine can be crashed early, it does not matter.
In the extreme, even kernel debuggers can be accessed in this way. I wrote
a small kgdb module and an accompanying gdb stub for FireWire which allows
to gdb to talk to kgdb using remote remory reads and writes over FireWire.
An version of the gdb stub fore FireWire is able to read all global data
from a system which is running a a normal kernel without any kernel debugger,
without any interruption or support of the system's CPU. That way, e.g. the
task struct and so on can be read and even manipulated when the physical DMA
access is granted.
A HOWTO is included in this patch, in Documentation/debugging-via-ohci1394.txt
and I've put a copy online at
ftp://ftp.suse.de/private/bk/firewire/docs/debugging-via-ohci1394.txt
It also has links to all the tools which are available to make use of it
another copy of it is online at:
ftp://ftp.suse.de/private/bk/firewire/kernel/ohci1394_dma_early-v2.diff
Signed-Off-By: Bernhard Kaindl <bk@suse.de>
Tested-By: Thomas Renninger <trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
Convert to use the class iteration api.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes. I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.
The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev. (basically all inquiries it
issues can now be directly mapped).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Torsten Kaiser wrote:
> Looking that calltrace upwards, it seems replacing the
> memset(dma->sglist,...) with sg_init_table(...) would fix the BUG_ON()
> as that inits the SG_MAGIC.
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes dead code spotted by the Intel C Compiler.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commits
58b053e4ce ("Update arch/ to use sg helpers")
45711f1af6 ("[SG] Update drivers to use sg helpers")
fa05f1286b ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/ieee1394/ieee1394_core.c: Define spinlock using
DEFINE_SPINLOCK instead of assignment to SPIN_LOCK_UNLOCKED
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
At least since nodemgr got rid of coarse global locking, accesses to
struct csr1212_keyval's reference counter should be atomic and coupled
with proper barriers. Also, calls to csr1212_keep_keyval(kv) should
occur before kv is being used.
(We probably should convert refcnt to struct kref, but how to keep
csr1212_destroy_keyval's implementation non-recursively then?)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
csr1212_keep_keyval(kv) in nodemgr_process_root_directory was
unbalanced if ne->vendor_name_kv already exists. This happens for
example if eth1394 or raw1394 modify the local config ROM and it is
parsed again.
As a bonus, the attempt to add the vendor_name_kv sysfs attribute
when it already exists is now fixed for good.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* Delete optional and empty i2c client_register and client_unregister
callbacks.
* Use the proper i2c adapter ID.
* Don't use a template to initialize the i2c_adapter structure, it's
inefficient.
* Update a misleading comment on why we use i2c_transfer rather than
higher level i2c functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The nodemgr host thread can exit on its own even when kthread_should_stop
is not true, on receiving a signal (might never happen in practice, as
it ignores signals). But considering kthread_stop() must not be mixed with
kthreads that can exit on their own, I think changing the code like this
is clearer. This change means the thread can cut its sleep short when
receive a signal but looking at the code around, that sounds okay (and
again, it might never actually recieve a signal in practice).
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
sbp2_host_reset and sbp2_handle_status_write are not serialized against
sbp2_alloc_device and sbp2_remove_device.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap the hard_header_parse function to simplify next step of
header_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialization of ohci1394 was broken according to one reporter if the
driver was statically linked, i.e. not built as loadable module. Dmesg:
PCI: Device 0000:02:07.0 not available because of resource collisions
ohci1394: Failed to enable OHCI hardware.
This was reported for a Toshiba Satellite 5100-503. The cause is commit
8df4083c52 in Linux 2.6.19-rc1 which only
served purposes of early remote debugging via FireWire. This
functionality is better provided by the currently out-of-tree driver
ohci1394_earlyinit. Reversal of the commit was OK'd by Andi Kleen.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Bug found by Olaf Hering <olh@suse.de>:
sbp2util_remove_command_orb_pool requires a valid lu->hi pointer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Make the option SBP2_PHYS_DMA available on all architectures where it
compiles. This includes x86-64 where I runtime-tested it successfully.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Revert commit 0555659d63 from 2.6.22-rc1.
The dma_set_mask call somehow failed on a PowerMac G5, PPC64:
http://lkml.org/lkml/2007/8/1/344
Should there ever occur a DMA mapping beyond the physical DMA range, a
proper SBP-2 firmware will report transport errors. So let's leave it
at that.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Olaf Hering <olh@suse.de>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Going through the string and waiting for _pointer_ to become '\0'
is not what the authors meant...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Ben Collins <ben.collins@ubuntu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on patch "the scheduled removal of RAW1394_REQ_ISO_{SEND,LISTEN}"
from Adrian Bunk, November 20 2006.
This patch also removes the underlying facilities in ohci1394 and
disables them in pcilynx. That is, hpsb_host_driver.devctl() and
hpsb_host_driver.transmit_packet() are no longer used for iso reception
and transmission.
Since video1394 and dv1394 only work with ohci1394 and raw1394's rawiso
interface has never been implemented in pcilynx, pcilynx is now no
longer useful for isochronous applications.
raw1394 will still handle the request types but will complete the
requests with errors that indicate API version conflicts.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This is upwards compatible, except that integer values other than 0 or 1
are no longer accepted. But values like "Y", "N", "no", "nnoooh!" work
now.
Also, improve a comment on the serialize_io parameter and make the
ORB_SET_EXCLUSIVE macro ultra-safe.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Association of a host device with a node on NUMA machines optimizes
allocations of skbs given from the networking stack to eth1394.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
After ieee1394 was converted away from class_device like the networking
subsystem was already in 2.6.21, eth1394's device may point to the
fw-host device as its parent again like in 2.6.20.
This affects userspace tools which examine the sysfs representation of
eth1394's device.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Remove the global nodemgr_serialize mutex which enclosed most of the
host thread event loop. This allows for parallelism between several
host adapter cards.
Properly serialize the driver hooks .update(), .suspend(), .resume(),
and .remove() by means of device->sem. These hooks can be called from
outside the host threads' contexts.
Get() and put() the device.driver when calling its hooks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Here is a straightforward conversion to "struct device". The "struct
class_device" will be removed from the kernel.
It seems to work fine for me with and without CONFIG_SYSFS_DEPRECATED
set.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
I was told that only i386 aligns 64 bit integers at 4 bytes boundaries
while all other architectures (32 bit architectures with 64 bit
siblings) align it on 8 bytes boundaries.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Pointed out by Arnd Bergmann: PPC32 aligns this at 64bit, IA32 packs
it. A kernel-wide available __compat_u64 which is 4-byte aligned on
AMD64 and IA64 would be nicer though.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add compat_ioctl. Although all structures are more or less same,
raw1394_iso_packets got pointer inside, and raw1394_cycle_timer got unwanted
padding in the middle. I did not add any translation for ioctls passing array
of integers around as integers seem to have same size (32 bits) on all
architectures supported by Linux.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Acked-by: Dan Dennedy <dan@dennedy.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
* write(fd, buf, 52) from 32bit app was returning 56. Most of callers did not
care, but some (arm registration) did, and anyway it looks bad if request for
writing 52 bytes returns 56. And returning sizeof anything in 'int' is not
good as well. So all functions now return '0' instead of
sizeof(struct raw1394_request) on success, and write() itself provides correct
return value (it just returns value it was asked to write on success as raw1394
does not do any partial writes at all).
* Related to this was problem that write() could have returned 0 when kernel
state would become corrupted and moved to different state than
opened/initialized/connected. Now it returns -EBADFD which seemed appropriate.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Acked-by: Dan Dennedy <dan@dennedy.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
read() always failed with -EFAULT. This was happening due to
raw1394_compat_read copying data to wrong location - access_ok always
failed as 'r' is kernel address, not user. Whole function just tried to
copy data from 'r' to 'r', which is not good.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Acked-by: Dan Dennedy <dan@dennedy.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (split into 3 patches)
This patch fixes a problem that occurs when packets cannot be sent across
the ieee1394 bus and we return NETDEV_TX_BUSY in the net driver "hard start
xmit" routine ether1394_tx. When we return NETDEV_TX_BUSY the stack will
call ether1394_tx again with the same skb. So we need to restore the header
to look like it did before we munged it for xmit over ieee1394.
[Stefan Richter: changed whitespace, deleted a local variable]
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
With "modprobe sbp2 long_ieee1394_id=y", the format of
/sys/bus/scsi/devices/*:*:*:*/ieee1394_id is changed from e.g.
0001041010004beb:0:0 to 0001041010004beb:00042c:0000.
The longer format fully conforms to object identifier sizes as per
SAM(-2...4) and reflects what the SAM target port identifier is meant to
contain: A Discovery ID allegedly specified by ISO/IEC 13213:1994 ---
however there is no such thing; the authors of SAM probably meant
Directory ID). Especially target nodes with multiple dynamically added
targets may use Directory IDs to persistently identify target ports.
The new format is independent of implementation details of nodemgr.
Thus the same ieee1394_id attribute format can be implemented in the new
firewire stack.
The ieee1394_id is typically used to create persistently named links in
/dev/disk/by-id.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While playing with libiec61883 I've noticed that async_send is broken
because it was doing copy_from_user(...., packet->data_size) before
packet->data_size was set to any useful value. It got broken when
packet->allocated_data_size got introduced, as hpsb_alloc_packet does
not set packet->data_size anymore. (Regression in 2.6.22-rc1)
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This adds a real parent device to eth1394's ethX device like in Linux
2.6.20 and older. However, due to unfinished conversion of the ieee1394
away from class_device, we now refer to the FireWire controller's PCI
device as the parent, not to the ieee1394 driver's fw-host device.
Having a real parent device instead of a virtual one allows udev scripts
to distinguish eth1394 interfaces from networking bridges, bondings and
the likes.
Fixes a regression since 2.6.21:
https://bugs.gentoo.org/show_bug.cgi?id=177199
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When eth1394 was unable to acquire a transaction label, it just dropped
outgoing packets without attempt to resend them later.
The transmit queue is now halted if no tlabel is available to
->hard_start_xmit(). A workqueue job is then scheduled to catch the
moment when ieee1394 recycled the next lot of tlabels.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=8402
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'juju' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (138 commits)
firewire: Convert OHCI driver to use standard goto unwinding for error handling.
firewire: Always use parens with sizeof.
firewire: Drop single buffer request support.
firewire: Add a comment to describe why we split the sg list.
firewire: Return SCSI_MLQUEUE_HOST_BUSY for out of memory cases in queuecommand.
firewire: Handle the last few DMA mapping error cases.
firewire: Allocate scsi_host up front and allocate the sbp2_device as hostdata.
firewire: Provide module aliase for backwards compatibility.
firewire: Add to fw-core-y instead of assigning fw-core-objs in Makefile.
firewire: Break out shared IEEE1394 constant to separate header file.
firewire: Use linux/*.h instead of asm/*.h header files.
firewire: Uppercase most macro names.
firewire: Coding style cleanup: no spaces after function names.
firewire: Convert card_rwsem to a regular mutex.
firewire: Clean up comment style.
firewire: Use lib/ implementation of CRC ITU-T.
CRC ITU-T V.41
firewire: Rename fw-device-cdev.c to fw-cdev.c and move header to include/linux.
firewire: Future proof the iso ioctls by adding a handle for the iso context.
firewire: Add read/write and size annotations to IOC numbers.
...
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refine some depends statements to limit their visibility to the
environments that are actually supported.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- s/Device Drivers/Controllers/
- clarify who needs pcilynx
- don't recommend Y for raw1394; M is typically used
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix the "attempting to setting" message in ohci1394.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Remove the unneeded code that clears, sets and again clears the
rcvPhyPkt bit in the ohci1394 LinkControl register in ohci_initialize().
Signed-off-by: Bernhard Kauer <kauer@os.inf.tu-dresden.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If posted write failed, an "Unhandled interrupt(s) 0x00000100" message
was logged by mistake.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
eth1394 did not work on buses consisting of S100B...S400B hardware
because it attempted to send GASP packets at S800.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch fixes some error handlings in eth1394:
- check return value of kmem_cache_create()
- cleanup resources if hpsb_register_protocol() fails
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (whitespace)
This patch actually doesn't change anything because there was always 0
== NETDEV_TX_OK returned before.
TODO: Return NETDEV_TX_BUSY in error case and test in different error
conditions.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
RFC 2734 says: "IP-capable nodes may operate with an MTU size larger
than the default [1500 octets], but the means by which a larger MTU is
configured are beyond the scope of this document."
Allow users to set an MTU bigger than 1500.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
highlevel_host_reset no longer has any modular users.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Call only eth1394's own host reset handler from .tx_timeout, not the
reset hooks of all other IEEE 1394 drivers.
A minor drawback of this patch is that ether1394_host_reset by timeout
is not serialized against ether1394_host_reset by bus reset.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Move common code into an extra function. This implicitly adds a missing
node_info->fifo = CSR1212_INVALID_ADDR_SPACE; to .update.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Adjust white space and line wraps. Remove unnecessary parentheses and
braces, unused macros, and some of the more redundant comments.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
There is some common code between ether1394_open and ether1394_add_host
which can be moved to a separate helper function for a slightly smaller
eth1394 driver (-160 bytes on i386.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Until now, ieee1394 put an IP-over-1394 capability entry into each new
host's config ROM. As soon as the controller was initialized --- i.e.
right after modprobe ohci1394 --- this entry triggered a hotplug event
which typically caused auto-loading of eth1394.
This irritated or annoyed many users and distributors. Of course they
could blacklist eth1394, but then ieee1394 wrongly advertized IP-over-
1394 capability to the FireWire bus.
Therefore
- remove the offending kernel config option
IEEE1394_CONFIG_ROM_IP1394,
- let eth1394 add the ROM entry by itself, i.e. only after eth1394 was
loaded.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=7793 .
To emulate the behaviour of older kernels, simply add the following to
to /etc/modprobe.conf:
install ohci1394 /sbin/modprobe eth1394; \
/sbin/modprobe --ignore-install ohci1394
Note, autoloading of eth1394 when an _external_ IP-over-1394 capable
device is discovered is _not_ affected by this patch.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Shrinks eth1394.ko by about 5%.
Many of these functions have only one caller and are therefore auto-
inlined anyway.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Warn if hpsb_allocate_and_register_addrspace() failed.
Unregister the address space if something else failed.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The comment says it all. This affects only asynchronous streams sent
via raw1394; the eth1394 driver has own code and needs an own fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Everytime when eth1394 or a libraw1394 client updates the configuration
ROM, a certain sysfs attribute cannot be added since it already exists.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This is a coding style touch-up for ieee1394's handle_incoming_packet().
A preprocessor macro contained hardwired variable names and, even worse,
the 'break' keyword. This macro is now unrolled and removed.
Also, all 'break's which had the effect of a return are replaced by
return. And a FIXME comment is brought up to date.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>