When CONFIG_SND_SOC_CS4270_VD33_ERRATA is set, there was a mismatch between
the mclk_ratios[] and cs4270_mode_ratios[] arrays. The two arrays have been
merged and code has been shuffled. One side effect is that the
cs4270_set_dai_sysclk() and cs4270_set_dai_fmt() functions are available only
if I2C has been enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Disable the simultaneous load feature for the line in and headphone
out volume registers. This allows left and right volume levels to
be controlled separately.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds ALSA SoC support for TI TLV320AIC3X audio codecs.
The features that are supported:
o Capture/Playback/Bypass.
o 16/20/24/32 bit audio.
o 8k - 96k sample rates.
o codec master only mode
o DAPM.
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
On Zaurus SL-C3200 (terrier/spitz) based on WM8750, treble scale is
inconveniently reverted (increase level = decrease treble), in opposite
to bass scale, which uses convenient scale.
Fix ALSA WM8750 mixer treble to use convenient treble scale (increase =
increase treble level)
From: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Change loops in ac97_read/write functions to count down to zero
rather than up. Gcc will then use the 'dt' (decrement-and-test) op
instead of an increment/compare op-pair.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds ac97 support for ln2440sbc board from LittleChips.
This board is based on s3c2440 SoC + AC97 Realtek ALC650 codec.
Existing s3c2443 implementation is slightly modified because s3c2440
and s3c2443 have different AC97 interrupts.
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The following patch adds 'Mono Playback Switch' control to WM9712 codec
SoC driver.
Also, it fixes Treble, Bass and Mono playback volume inversion bits.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix CKEN register corruption in the PXA27x cold reset code
located in sound/arm/pxa27x-ac97.c. The problem has been
introduced with a pxa_set_cken() function change in linux 2.6.23.
This patch is based on patch 4527/1 that fixes the same problem in
the ASoC PXA-AC97 driver. Additionally a definition for the CKEN
index value is added and applied to both PXA AC97 drivers.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the calculation of the private_data pointer in the CS4270 driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The Samsung S3C24xx uses new architecture file layout in the post 2.6.23
kernel. This patch fixes include path for the s3c2443-ac97.c.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix schedule_timeout() use in alsa-kernel. Mostly just
schedule_timeout(1) --> schedule_timeout_uninterruptible(1)
The wavefront_synth one fixes the surrounding loop as well. In ymfpci_main,
delete a superfluous set_current_state() and in soc/soc-dapm.c replace an
_interruptible with _uninterruptible in some debug code; it's not waiting
for signals.
Signed-off-by: Rene Herman <rene.herman>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The volume control for the CS4270 ASoC driver was inverted - raising the
volume level with alsamixer would decrease the actual volume.
This patch also improves the performance of the I2C code (used to change
register settings) by only performing an I2C write if the new value is
different from the value that's in the register cache.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add a snd_pcm_rate_to_rate_bit() function to factor out common code used
by several drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix compilation errors with the CS4270 when I2C is not enabled. Updated
some comments to indicate that that stand-alone mode is not fully implemented,
because there is no mechanism for the CS4270 driver and the machine driver to
communicate the values of various input pins.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds ALSA SoC support for the Cirrus Logic CS4270 codec. The
following features are suppored:
1) Stand-alone and software mode
2) Software mode via I2C only
3) Master mode, not Slave
4) No power management
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Since the PCM emulation can call multiple times to hw_setup(), but we
can only once allocate/request the DMA channel, we have to handle
this gracefully.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
SND_S3C24XX_SOC_NEO1973_WM8753 depends on MACH_GTA01 but the Kconfig
entry which is going to be merged is MACH_NEO1973_GTA01.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch cleans up duplicate includes in
sound/soc/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
due to CKEN_xxx definition and pxa_set_cken() change, the pxa27x
ac97 cold reset is broken in ASoC, fixed to use bit index instead
of bit mask
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make s3c24xx_i2s_set_clkdiv() change the correct bits.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Somewhere when dealing with the s3c24xx patches and requested changes I
managed to miss this file on re-submission.
Its a header file required for compilation of neo1973-wm8573.c and
should be a no brainer.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Let SND_SOC_PCM_SH7760 depend on SH_DMABRG rather than select'ing it.
Gets rid of the Kbuild warning about SH_DMABRG being undefined on non-sh
builds.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
ALSA ASoC support for SH7760
This patch adds ALSA ASoC drivers for the Audio interfaces
of the SH7760 SoC:
Add driver for the SH7760 DMA engine (dmabrg)
Add AC97 driver for HAC unit(s) found on SH7760/SH7780
Add I2S driver for SSI unit(s) found on SH7760/SH7780
Add a generic SH7760-AC97 machine driver.
Hook it all up with the build system.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds Kconfig and build support for the Neo1973, SMDK2443 and
S3C2443 AC97 ALSA audio drivers.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds ALSA support for the Openmoko Neo1973 phone. Features:-
* HiFi Playback and capture.
* Phone calls supported.
* Support for BT PCM in WM8753 voice interface.
* Support for LM4857 audio amp.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The PXA CKEN changes broken syspend/resume on the pxa27x. This patch
corrects the problem and fixes another couple of bad references.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This should fix a spinlock lockup bug on the s3c24xx arch.
From: Zoltan Devai <zdevai@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes a bug whereby AC97 bus device data was being clobbered
when AC97 codecs using the generic ac97_codec.c driver were being
registered. Codecs that didn't use the generic driver were unaffected
(e.g. WM9712, WM9713).
Changes:-
o Add new AC97 codec class for custom (or need bus dev registration)
AC97 codecs.
o Only register/deregister this custom codec device with the AC97 bus.
The generic AC97 driver already does this for generic codec devices.
This may be related to bug #3038 :-
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3038
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes a bug whereby the GPL'ed symbol ac97_dai was being
declared as static.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
I quuestion the testing status of that patch!
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch makes the ASoC Kconfig descriptions a little more meaningful.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch cleans up the audio DMA for the Samsung S3C24xx platform.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch exports the ASoC AC97 Digital Audio Interface as a GPL'ed
symbol.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds the WM8753 codec driver to the kernel build system.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch series adds support for the WM8753 codec as found on the
OpenMoko Neo 1973 (other Neo 1973 and Samsung S3C24xx patches to follow
today) as well other new devices.
Features:-
o HiFi and Voice DAI supported (inc runtime switching of DAI mode)
o DAPM
o All mixers
o PLL calculator
o 16,20 and 24bit samples.
o WM8753 I2C ID added to include/linux/i2c-id.h
From: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch by Frank Madarino updates the AT91xxxx Makefile and Kconfig
to build the renamed SSC files.
Changes:-
o Rename various i2s labels to ssc
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch by Frank Madarino updates the eti B1 machine to use the newer
AT91xxxx SSC core with the DSP/PCM audio hardware changes.
Changes:-
o #include 'at91-ssc.h' instead of 'at91-i2s.h'
o Rename various I2S labels to SSC
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch series by Frank Madarino updates the AT91xxxx core to add
DSP/PCM audio hardware formats.
Changes:-
o Rename at19-i2s.c -> at91-ssc.c
o Rename at91-i2s.h -> at91-ssc.h
o Add DSP hardware formats.
o Rename various I2S labels to SSC
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes an issue whereby power was applied to any inactive
analog path that would leave and reenter a codec (e.g. ACOP -> ACIN on
WM8753). This change now checks for such paths and DAPM will power them
down when not in use.
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch creates the WM9712 codec register cache using kmemdup instead
of doing a kzalloc followed by a memcpy.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The new ALSA 'SOC' support has bogus Kconfig ... it should
not be presenting anything AT91-related except on AT91,
or anything PXA-related except on PXA. Right now, x86
sees both of those menus, as do all other platforms.
This patch removes needless Kconfig layering, and the
related inappropriate choice presentation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch by Ben Dooks from Simtec Electronics adds ASoC audio DMA
support for the Samsung S3C24xx CPU.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch by Ben Dooks from Simtec Electronics adds ASoC I2S support
for the Samsung S3C24xx CPU.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch suggested by Joe Sauer adds PCM playback volume kcontrol for
the WM9712.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch by Joe Sauer fixes the WM9712 codec register cache value for
register 0x08. Value should be 0x0f0f and not 0xf0f0.
Signed-off-by: Joe Sauer <jsauer@vernier.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Use the new PDC register name defines that were updated
in Linux 2.6.20.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the Sharp poodle machine driver to the new API in
ASoC 0.13.
Changes:-
o Manually configure DAI hardware format.
o Removed config_sysclk() function. No longer needed as clocking is now
configured manually.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the Sharp tosa machine driver to the new API in ASoC
0.13.
Changes:-
o Update machine operations to new API.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the Sharp spitz machine driver to the new API in ASoC
0.13.
Changes:-
o Manually configure DAI hardware format.
o Removed config_sysclk() function. No longer needed as clocking is now
configured manually.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the Sharp corgi machine driver to the new API in ASoC
0.13.
Changes:-
o Manually configure DAI hardware format.
o Removed config_sysclk() function. No longer needed as clocking is now
configured manually.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the pxa2xx I2S driver to the new API in ASoC 0.13.
Changes:-
o Added check in hw_params to detect buffer less pcms (i.e. BT <-->
codec).
o Updated structures to new API
o Removed DAI's and ac97 ops from PCM header.
o Integer hardware constraint added for periods.
Signed-off-by: Andrew Johnson <ajohnson@intrinsyc.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the pxa2xx AC97 driver to the new API in ASoC 0.13.
Changes:-
o Removed DAI capabilities matching code in favour of manual matching in
the machine drivers.
o Added DAI operations for codec and CPU interfaces.
o Added pxa2xx-ac97.h header
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the pxa2xx I2S driver to the new API in ASoC 0.13.
Changes:-
o Removed DAI capabilities matching code in favour of manual matching in
the machine drivers.
o Added DAI operations for codec and CPU interfaces.
o Removed config_sysclk() function and struct snd_soc_clock_info. No
longer needed as clocking is now configured manually in the machine
drivers. Also removed other clocking data from structures.
o Added pxa2xx-i2s.h header
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the EtI B1 machine driver to the new API in ASoC
0.13.
Changes:-
o Manually configure DAI hardware format.
o Removed config_sysclk() function. No longer needed as clocking is now
configured manually.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the AT91xxxx audio DMA driver to the new API in ASoC
0.13.
Changes:-
o Updated to use new 0.13 data structures.
o Suspend and Resume now conditionally compiled.
o #include guard around at91-pcm.h header.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the AT91xxxx I2S driver to the new API in ASoC 0.13.
Changes:-
o Removed DAI capabilities matching code in favour of manual matching in
the machine drivers.
o Added DAI operations for codec and CPU interfaces.
o Removed config_sysclk() function and struct snd_soc_clock_info. No
longer needed as clocking is now configured manually in the machine
drivers. Also removed other clocking data from structures.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for I2S slave mode for the ETI_B1 machine from
Endrelia.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the AC97 codec driver to the new API in ASoC 0.13.
Changes:-
o Removed DAI capabilities matching code in favour of manual matching in
the machine drivers.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the WM9712 codec driver to the new API in ASoC 0.13.
Changes:-
o Removed DAI capabilities matching code in favour of manual matching in
the machine drivers.
o Added DAI operations for codec and CPU interfaces.
o Removed config_sysclk() function and struct snd_soc_clock_info. No
longer needed as clocking is now configured manually in the machine
drivers. Also removed other clocking data from structures.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the WM8750 codec driver to the new API in ASoC 0.13.
Changes:-
o Removed DAI capabilities matching code in favour of manual matching in
the machine drivers.
o Added DAI operations for codec and CPU interfaces.
o Removed config_sysclk() function and struct snd_soc_clock_info. No
longer needed as clocking is now configured manually in the machine
drivers. Also removed other clocking data from structures.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the WM8731 codec driver to the new API in ASoC 0.13.
Changes:-
o Removed DAI capabilities matching code in favour of manual matching in
the machine drivers.
o Added DAI operations for codec and CPU interfaces.
o Removed config_sysclk() function and struct snd_soc_clock_info. No
longer needed as clocking is now configured manually in the machine
drivers. Also removed other clocking data from structures.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes a bug whereby an unnamed stream would cause a NULL
pointer ref in snd_soc_dapm_stream_event().
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch updates the ASoC core to the new DAI matching and clocking
API in version 0.13
Changes:-
o Removed DAI capabilities matching code in favour of manual matching
in the machine drivers.
o Added DAI operations for codec and CPU interfaces.
o Removed config_sysclk() function and struct snd_soc_clock_info. No
longer needed as clocking is now configured manually in the machine
drivers. Also removed other clocking data from structures.
o Added machine driver prepare callback.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This very minor patch fixes the snd_soc_new_pcms() function to comply
with the kernel coding style.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes a bug whereby the power management delayed work would
never be run at driver suspend() or module remove(). Delayed work would
be created (after audio had finished) with a long delay (~5 secs) and
was sometimes never queued before flush_scheduled_work() was being
called at suspend or module remove. This caused the delayed work to
queued after the module had been removed or after resume.
This patch forces any delayed work to complete by cancelling it (timer
cannot fire and add it to queue later), scheduling it for now and
waiting on it's completion.
This is something I probably would like to add to workqueue.c in the
next merge window, however it's here atm because it can oops.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for 32k audio on the WM8731 when running from a
12MHz system clock.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch improves the codec probe() error reporting by printing error
messages when the card or pcms fail to register.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes a bug whereby some resources were not being freed when
codec probe() failed.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes a NULL pointer exception which occurs when a
substream is opened and immediately closed.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
soc-dapm
·Removed list_for_each since the loop is list_for_each_entry() and
not list_for_each(). Thanks to Liam Girdwood and Seth Forshee.
at91-i2s
·Fixed typo in dai modes definition.
·Fixed struct member name in at91_ssc_info->ssc_state.
·Fixed compilation problem, ssc_state is bundled in at91_ssc_info.
Signed-off-by: Raúl Sánchez Siles <rss@barracuda.es>
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the changes realted to delayed_work in soc/codecs/wm8750.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Use global workqueue for simplicity instead of own workqueue
in SoC core and wm8750 codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds copyright and credit for my good friend Richard Purdie
from OpenedHand for his help and code contribution throughout the
development of the core code. Many thanks Richard (I guess we overlooked
this in trying to get everything working well).
It also adds some extra comments wrt to DAI clock matching.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch removes some trailing white space from the WM9712 ASoC codec
driver.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
From: Andrew Morton <akpm@osdl.org>
I converted the workqueues to per-device while I was there. It seems
strange to create a new kernel thread (on each CPU!) and to then only
have a single global work to ever be queued upon it.
Plus without this, I'd have to use the _NAR stuff, gawd help me.
Does that workqueue really need to be per-cpu?
Does that workqueue really need to exist? Why not use keventd?
Cc: Takashi Iwai <tiwai@suse.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Make the following needlessly global functions static:
- dapm_power_widgets()
- dapm_mux_update_power()
- dapm_mixer_update_power()
- dapm_free_widgets()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch by Philipp Zabel fixes a bug whereby the BCLK matching fails
when the Codec BCLK is constant and the CPU BCLK is based upon a
divider.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Changes were required to support latest AT91 header files.
Also updated to remove AT91RM9200-specific code in the ASoC
platform drivers to support the AT91SAM9260 and AT91SAM9261
chips, but no testing was performed on these chips.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch suggested by Richard Purdie changes the names of some WM8731
and WM8750 mixers so that they will be recognised by some older OSS
mixer apps.
Changes:-
o WM8731 Playback changed to Master Playback
o WM8750 Out1 changed to Headphone
o WM8750 Out2 changed to Speaker
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch by Frank Mandarino and Hubert Kahlert fixes a bug in the AT91
SSC (i2s) shutdown code that would erroneously disable other AT91
peripheral clocks.
Signed-off-by: Hubert Kahlert <hkahlert@hk-datentechnik.de>
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for the DAI BCLK to be generated by multiplying
Rate * Channels * Word Size (RCW).
This now gives 3 options for BCLK clocking and synchronisation :-
1. BCLK = Rate * x
2. BCLK = MCLK / x
3. BCLK = Rate * Chn * Word Size. (New)
Changes:-
o Add support for RCW generation of BCLK
o Update Documentation to include RCW.
o Update DAI documentation for label = value DAI modes.
o Add RCW support to wm8731, wm8750 and pxa2xx-i2s drivers.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch by Frank Mandarino updates the AT91RM9200 I2S DAI audio modes
as follows:-
o fixes a typo in the 16k mode
o removes experimental 24k mode
o adds a 32k mode.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
