Commit Graph

590 Commits

Author SHA1 Message Date
Pierre Ossman
0b82684c3c sdhci: improve no card, no reset quirk
The quirk was meant to just inhibit some resets, but ended up blocking
all of them. Fortunately, this was just what was needed. Change the
comment to reflect reality.

Also, this issue has just been observed on Samsung laptops, so reduce
the number of chips the quirk affects.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
9d7c6eee52 MMC: OMAP: Do not busy wait for end of command for ever
The limit was a fixed 100k limit in the busy loop, which is not
accurate. It would better to have time limit for the worst case
which occurs when sending 80 cycles at 400 kHz and takes about
200 microseconds, so limit the max time spend in the busy loop
for some 250 microseconds.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
0f602ec79a MMC: OMAP: Start new commands from work queue instead of irq
Use work queues for starting new commands instead of starting them
directly from irq handler. The command scheduling needs to be delayed
a bit for some cards which should not be done from an interrupt.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
0807a9b573 MMC: OMAP: Lazy clock shutdown
MMCA spec says the mmc clock should be kept running for at least
8 cycles after the last RW request. Ensure this with lazy clock
disable after a request, or with an explicit delay before
switching a slot.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
0fb4723d40 MMC: OMAP: Move failing command abortion to workqueue
Abort failed command from workqueue rather than from an interrupt,
allowing longer delays in abortion.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
7584d276d4 MMC: OMAP: Use tasklet instead of workqueue for cover switch notification
The cover waitqueue is occasionally scheduled twice from timer
and the interrupt and oops follows. It would have been possible
to fix this problem with spinlocks but using tasklet was a dropin
solution with no need for locking.

This path also adds some cleanups.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:30 +02:00
Kyungmin Park
8348f0029d MMC: OMAP: Check the get_cover_state function pointer if not set
If the get_cover_state is not set, it occurs the oops.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:30 +02:00
Carlos Eduardo Aguiar
01e77e13fc MMC: OMAP: Using setup_timer instead of init_timer
Using setup_timer() instead of init_timer() on omap.c file.

Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:30 +02:00
Jarkko Lavinen
eb1860bccd MMC: OMAP: Abort stuck commands
When a card is removed while it is being accessed, a command can get stuck so
that no timeout or end of command interrupt ever occurs. The command getting
stuck is almost always CDM12, but also the other commands can get stuck. Catch
a stuck command with a timer and try sending the initialization stream until
the controller starts running again and responds with the end of command
status.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:30 +02:00
Juha Yrjola
2a50b8889b MMC: OMAP: General cleanup for MMC multislot support
General code cleanup, modifications at some dev_* functions and
other hacks at mmc_omap_irq() for MMC multislot support.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:29 +02:00
Juha Yrjola
65b5b6e51b MMC: OMAP: Power functions modified to MMC multislot support
Modifications at power functions to MMC multislot support. This patch
also move board-specific code out of MMC OMAP driver.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:29 +02:00
Juha Yrjola
b8f9f0e90a MMC: OMAP: Fix timeout calculation for MMC multislot support
Fix the data timeout calculation for MMC multislot support.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:29 +02:00
Juha Yrjola
a914ded235 MMC: OMAP: New release dma and abort xfer functions
New functions to support MMC multislot:
mmc_omap_release_dma() and mmc_omap_abort_xfer().

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:29 +02:00
Juha Yrjola
5a0f3f1f71 MMC: OMAP: Add back cover switch support
This patch adds back MMC cover switch support in a way that
supports multiple slots.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:28 +02:00
Juha Yrjola
abfbe5f785 MMC: OMAP: Introduce new multislot structure and change driver to use it
Introduce new MMC multislot structure and change driver to use it.

Note that MMC clocking is now enabled in mmc_omap_select_slot()
and disabled in mmc_omap_release_slot().

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:28 +02:00
Tony Lindgren
4bc9e35556 MMC: OMAP: Remove cover switch handling to allow adding multislot support
This patch removes the MMC cover switch handling temporarily
to make following multislot patches cleaner.

MMC cover switch handling will be added back in later patches
after adding basic multislot support.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:28 +02:00
Francisco Alecrim
d365abe27d MMC: OMAP: Fix the BYTEBLOCK capability removal
According with commit 255d01af9a
from Linux-OMAP tree, the BYTEBLOCK capability was removed by Pierre Ossman.
MMC_CAP_BYTEBLOCK is not defined causing the compile error:

drivers/mmc/host/omap.c: In function `mmc_omap_probe':
drivers/mmc/host/omap.c:1077: error: `MMC_CAP_BYTEBLOCK' undeclared (first use in this function)
drivers/mmc/host/omap.c:1077: error: (Each undeclared identifier is reported only once
drivers/mmc/host/omap.c:1077: error: for each function it appears in.)

Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Tony Lindgren
ec2f362a91 MMC: OMAP: Remove extra divisor increase
As noted by Kyungmin Park, the divisor calculation has
an unnecessary increase.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Carlos Eduardo Aguiar
5ec21b1ccf MMC: OMAP: Remove some opcodes from host driver
This patch removes some opcodes from host driver so there's no need on putting
'#include <linux/mmc/mmc.h>', that should not be needed in host drivers.

Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Robert P. J. Day
6fee65cfde mmc: use shorter, equivalent set_current_state()
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Pierre Ossman
2f730fec83 sdhci: allow led to be controlled freely
Hook up the controller LED to the LED subsystem, allowing more flexible
control than simply indicating an ongoing request.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Pierre Ossman
b69c905890 sdhci: remove custom controller name
Remove the use of the sdhci specific device name and use the mmc controller
name instead.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Pierre Ossman
ff3112f5ad mmc: set controller name early
Reorganise code so that mmc_hostname() works directly after allocation.
That way host drivers can use that name for resource allocations and
messages during probing.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:26 +02:00
Kay Sievers
bc65c724d5 mmc: fix platform driver hotplug/coldplug
Since 43cc71eed1, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable MMC host
platform drivers, to re-enable auto loading.

Also, add missing owner declarations in driver init.

[dbrownell@users.sourceforge.net: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-15 19:35:40 -07:00
Pierre Ossman
51ec92e295 mmc: use sysfs groups to handle conditional attributes
Suppressing uevents turned out to be a bad idea as it screws up the
order of events, making user space very confused. Change the system to
use sysfs groups instead.

This is a regression that, for some odd reason, has gone unnoticed for
some time. It confuses hal so that the block devices (which have the
mmc device as a parent) are not registered. End result being that
desktop magic when cards are inserted won't work.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-22 17:02:20 -07:00
Roel Kluin
ce63645234 tifm_sd: DATA_CARRY is not boolean in tifm_sd_transfer_data()
DATA_CARRY is not boolean

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-15 09:24:21 -07:00
Frank Seidel
882c49164d mmc: extend ricoh_mmc to support Ricoh RL5c476
This patch adds support for the Ricoh RL5c476 chip: with this
the mmc adapter that needs this disabler (R5C843) can also be
handled correctly when it sits on a RL5c476.

Signed-off-by: Frank Seidel <fseidel@suse.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08 09:02:47 +01:00
David Brownell
6e996ee8e7 at91_mci: use generic GPIO calls
Update the AT91 MMC driver to use the generic GPIO calls instead of the
AT91-specific calls; and to request (and release) those GPIO signals.

That required updating the probe() fault cleanup codepaths.  Now there
is a single sequence for freeing resources, in reverse order of their
allocation.  Also that code uses use dev_*() for messaging, and has less
abuse of KERN_ERR.

Likewise with updating remove() cleanup.  This had to free the GPIOs,
and while adding that code I noticed and fixed two other problems:  it
was poking at a workqueue owned by the mmc core; and in one (rare)
case would try freeing an IRQ that it didn't allocate.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08 09:02:47 +01:00
Feng Tang
541ceb5b8b sdhci: add num index for multi controllers case
Some devices have several controllers; need add the index info to
device slot name host->slot_desc[]

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08 09:02:47 +01:00
Pierre Ossman
34671dc2e6 mmc: remove sdhci and mmc_spi experimental markers
Both of these drivers work well (although some hardware still has
its problems) and are not in the "alpha" quality that EXPERIMENTAL
suggests.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08 09:02:46 +01:00
Philip Langdale
1f090bf524 mmc: Handle suspend/resume in Ricoh MMC disabler
As pci config space is reinitialised on a suspend/resume cycle, the
disabler needs to work its magic at resume time. For symmetry this
change also explicitly enables the controller at suspend time but
it's not strictly necessary.

Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08 09:02:46 +01:00
Linus Torvalds
f0f0052069 Merge branch 'blk-end-request' of git://git.kernel.dk/linux-2.6-block
* 'blk-end-request' of git://git.kernel.dk/linux-2.6-block: (30 commits)
  blk_end_request: changing xsysace (take 4)
  blk_end_request: changing ub (take 4)
  blk_end_request: cleanup of request completion (take 4)
  blk_end_request: cleanup 'uptodate' related code (take 4)
  blk_end_request: remove/unexport end_that_request_* (take 4)
  blk_end_request: changing scsi (take 4)
  blk_end_request: add bidi completion interface (take 4)
  blk_end_request: changing ide-cd (take 4)
  blk_end_request: add callback feature (take 4)
  blk_end_request: changing ide normal caller (take 4)
  blk_end_request: changing cpqarray (take 4)
  blk_end_request: changing cciss (take 4)
  blk_end_request: changing ide-scsi (take 4)
  blk_end_request: changing s390 (take 4)
  blk_end_request: changing mmc (take 4)
  blk_end_request: changing i2o_block (take 4)
  blk_end_request: changing viocd (take 4)
  blk_end_request: changing xen-blkfront (take 4)
  blk_end_request: changing viodasd (take 4)
  blk_end_request: changing sx8 (take 4)
  ...
2008-01-29 08:51:32 +11:00
Russell King
0ff66f0c7a Merge branch 'pxa-plat' into devel
* pxa-plat: (53 commits)
  [ARM] 4762/1: Basic support for Toradex Colibri module
  [ARM] pxa: fix mci_init functions returning -1
  [ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix
  [ARM] 4747/1: pcm027: support for pcm990 baseboard for phyCORE-PXA270
  [ARM] 4746/1: pcm027: network support for phyCORE-PXA270
  [ARM] 4745/1: pcm027: default configuration
  [ARM] 4744/1: pcm027: add support for phyCORE-PXA270 CPU module
  [NET] smc91x: Make smc91x use IRQ resource trigger flags
  [ARM] pxa: add default config for littleton
  [ARM] pxa: add basic support for Littleton (PXA3xx Form Factor Platform)
  [ARM] 4664/1: Add basic support for HTC Magician PDA phones
  [ARM] 4649/1: Base support for pxa-based Toshiba e-series PDAs.
  [ARM] pxa: skip registers saving/restoring if entering standby mode
  [ARM] pxa: fix PXA27x resume
  [ARM] pxa: Avoid fiddling with CKEN register on suspend
  [ARM] pxa: Add PXA3 standby code hooked into the IRQ wake scheme
  [ARM] pxa: Add zylonite MFP wakeup configurations
  [ARM] pxa: program MFPs for low power mode when suspending
  [ARM] pxa: make MFP configuration processor independent
  [ARM] pxa: remove un-used pxa3xx_mfp_set_xxx() functions
  ...

Conflicts:

	arch/arm/mach-pxa/ssp.c

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-28 13:21:38 +00:00
Kiyoshi Ueda
fd539832c7 blk_end_request: changing mmc (take 4)
This patch converts mmc to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.

Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-01-28 10:36:52 +01:00
David Brownell
6d16bfb5e8 i2c/tps65010: move header to <linux/i2c/...>
Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-01-27 18:14:49 +01:00
Bridge Wu
fafc9d3fa3 [ARM] pxa: mmc: add 1st host controller support for pxa3xx
This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.

On zylonite, the first controller supports two slots, this patch
only support the first one right now.

Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:53 +00:00
Bridge Wu
9a788c6b78 [ARM] 4711/1: pxa: mmc: move DMA specific code to platform layer
This patch is to move pxamci DMA specific code to corresponding
platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes
the driver code dedicated to platform which is not extensible.

It is applicable to all pxa platforms.

Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:52 +00:00
Bridge Wu
64eb036af4 [ARM] 4709/1: pxa: mmc: add 26MHz support for pxa3[0|1]0 mmc controller
pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support
SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host
caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for
pxa3[0|1]0.

This patch is to add 26MHz support for them. pxa host clock will be
set to 26MHz mode when the card supported max clock rate is higher
than or equal to 26MHz.

Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:52 +00:00
Pierre Ossman
84c46a53fc sdhci: support JMicron JMB38x chips
The JMicron JMB38x chip doesn't support transfers that aren't 32-bit
aligned (both size and start address). It also doesn't like switching
between PIO and DMA mode, so it needs to be reset after each request.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12 20:01:00 +01:00
Pierre Ossman
c9fddbc4f8 sdhci: use PIO when DMA can't satisfy the request
Some controllers have been designed on the assumption that all transfers
will be 32-bit aligned, both in start address and in size. This is not a
guarantee the SDHCI specification provides and not one we can provide.

Revert back to PIO for individual requests in order to work around the
hardware bug.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12 20:01:00 +01:00
Pierre Ossman
c6573c9467 sdhci: don't warn about sdhci 2.0 controllers
We support 2.0 controllers, even though we don't use anything in the new
feature set.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12 20:01:00 +01:00
Pierre Ossman
dc93441b3f sdhci: describe quirks
Add a comment for each quirk to describe what it does and why.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-12-12 20:01:00 +01:00
Marc Pignat
c24b2602af spi: use simplified spi_sync() calling convention
Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification.  (Most didn't.)

Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:19 -08:00
Andre Haupt
a960d5dc71 sdio_uart: fix sign of paramter status in sdio_uart_receive_chars()
This also fixes a sparse warning about different signedness.
Only compile tested, because i do not have the hardware.

Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-11-29 19:10:30 +01:00
Haavard Skinnemoen
05e5b13645 mmc: Add missing sg_init_table() call
mmc_init_queue only initializes the scatterlists with sg_init_table()
when using a bounce buffer. This leads to a BUG() when CONFIG_DEBUG_SG
is set.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-11-27 09:19:40 +01:00
David Woodhouse
1dff314451 mmc: Avoid re-using minor numbers before the original device is closed.
Move the code which marks the minor number as free to mmc_blk_put() so
that it happens on the final close() (or removal), instead of doing it
at removal even when the device is still logically open.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-11-21 18:45:38 +01:00
Alex Dubov
b37a05069b tifm_sd: handle non-power-of-2 block sizes
It is possible to handle arbitrary block sizes with tifm card reader by
conditionally switching to PIO in case such block has to be delivered. At
the beginning of each request, DMA is either disabled (non-power-of-2 block
size) or set to load time user preference.

Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-11-21 18:42:45 +01:00
Pierre Ossman
d198f10198 mmc_block: check card state after write
Some cards have been reported to signal that they're ready prematurely.
Checking both the busy bit and card state solves the issue.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-11-21 18:40:53 +01:00
Rolf Eike Beer
cee687ce4a Add missing "\n" to log message
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-11-10 11:59:49 +01:00
Roland Dreier
8578007065 mmc: Fix sg helper copy-and-paste error
Commit 45711f1a ("[SG] Update drivers to use sg helpers") had the
following bogus change in drivers/mmc/card/queue.c:

    > -			src_buf = page_address(src->page) + src->offset;
    > +			src_buf = sg_virt(dst);

(Notice that "src" is converted to "dst").  Turn this "dst" back into
the intended "src".

Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-11-08 13:50:58 +01:00
Adrian Bunk
87ae9afdca cleanup asm/scatterlist.h includes
Not architecture specific code should not #include <asm/scatterlist.h>.

This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-11-02 08:47:06 +01:00
Russell King
d8cb70d10a [ARM] Fix pxamci regression
Fix:

WARNING: at arch/arm/mach-pxa/clock.c:69 clk_disable()
[<c002d7c8>] (dump_stack+0x0/0x14) from [<c00334f4>] (clk_disable+0x34/0xa0)
[<c00334c0>] (clk_disable+0x0/0xa0) from [<c028a43c>] (pxamci_set_ios+0x74/0xf0)
[<c028a3c8>] (pxamci_set_ios+0x0/0xf0) from [<c0281548>] (mmc_power_off+0x90/0x9c)
[<c02814b8>] (mmc_power_off+0x0/0x9c) from [<c0281a30>] (mmc_start_host+0x18/0x28)
[<c0281a18>] (mmc_start_host+0x0/0x28) from [<c02825a0>] (mmc_add_host+0xe8/0x104)
[<c02824b8>] (mmc_add_host+0x0/0x104) from [<c028a7d0>] (pxamci_probe+0x24c/0x2f4)
[<c028a584>] (pxamci_probe+0x0/0x2f4) from [<c01e5948>] (platform_drv_probe+0x20/0x24)
...

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-31 15:21:39 +00:00
Pavel Pisa
e1efa2a3ea Correction of "Update drivers to use sg helpers" patch for IMXMMC driver
The previous change omits "data->" prefix
in the "data->sg" case. This change fixes kernel
compilation.

Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>

 drivers/mmc/host/imxmmc.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
2007-10-29 09:18:04 +01:00
Al Viro
0ada7a02ad scatterlist fallout: mmc
#include <scatterlist/scatterlist.h>
is an odd thing to do...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-27 22:18:12 -07:00
David Brownell
460cd0589d mmc_spi: Fix mmc-over-spi regression
Patch 49dce689ad changed the sysfs data
structures for SPI in a way which broke the MMC-over-SPI host driver.

This patch fixes that regression by changing the scheme used to keep
from knowingly trying to use a shared bus segment, and updates the
adjacent comments slightly to better explain the issue.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-27 14:47:20 +02:00
Pierre Ossman
1fa8dd146f mmc: use common byte swap macros
Use the more generic byte swapping macros instead of the socket variants.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-27 14:41:04 +02:00
Pierre Ossman
78e480731a mmc: fix cid and csd byte order
MMC over SPI sends the CID and CSD registers as data, not responses,
which means that the host driver won't do the necessary byte flipping
for us.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-27 14:14:23 +02:00
Pierre Ossman
6356a9d955 at91_mci: Fix bad reference
The flags parameter got removed in a previous commit, but some
references were overlooked.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-27 14:04:10 +02:00
Jens Axboe
bd6dee6f30 mmc: sg fallout
Do a full scan of the directory to try and be a bit more proactive,
instead of waiting for things to break.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-24 09:01:09 +02:00
Ralf Baechle
117636092a [PATCH] Fix breakage after SG cleanups
Commits

  58b053e4ce ("Update arch/ to use sg helpers")
  45711f1af6 ("[SG] Update drivers to use sg helpers")
  fa05f1286b ("Update net/ to use sg helpers")

converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included.  This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.

On most of the others this probably broke.

Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-23 12:02:39 -07:00
Emil Medve
4e0177647a mmc: fix sg->page fallout
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-23 20:37:24 +02:00
Jens Axboe
45711f1af6 [SG] Update drivers to use sg helpers
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-22 21:19:53 +02:00
Andrew Victor
9e3866b548 mmc: at91_mci: cleanup: use MCI_ERRORS
A small MMC driver cleanup.

Use the defined AT91_MCI_ERRORS in at91_mci_completed_command() instead
of specifying all the error bits individually.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-17 21:35:10 +02:00
Florin Malita
00cedfa67b mmc: possible leak in mmc_read_ext_csd
The exception path associated with an invalid ext_csd_struct returns
without freeing ext_csd.

Coverity CID 1909.

Signed-off-by: Florin Malita
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-17 21:33:46 +02:00
Al Viro
e5712a6a98 missing include in mmc
AFAICS, fallout from repacing include of blkdev.h with include of bio.h.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 19:05:30 -07:00
Linus Torvalds
92d15c2ccb Merge branch 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block: (63 commits)
  Fix memory leak in dm-crypt
  SPARC64: sg chaining support
  SPARC: sg chaining support
  PPC: sg chaining support
  PS3: sg chaining support
  IA64: sg chaining support
  x86-64: enable sg chaining
  x86-64: update pci-gart iommu to sg helpers
  x86-64: update nommu to sg helpers
  x86-64: update calgary iommu to sg helpers
  swiotlb: sg chaining support
  i386: enable sg chaining
  i386 dma_map_sg: convert to using sg helpers
  mmc: need to zero sglist on init
  Panic in blk_rq_map_sg() from CCISS driver
  remove sglist_len
  remove blk_queue_max_phys_segments in libata
  revert sg segment size ifdefs
  Fixup u14-34f ENABLE_SG_CHAINING
  qla1280: enable use_sg_chaining option
  ...
2007-10-16 10:09:16 -07:00
Tony Jones
49dce689ad spi doesn't need class_device
Make the SPI framework and drivers stop using class_device.  Update docs
accordingly ...  highlighting just which sysfs paths should be
"safe"/stable.

Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:43:10 -07:00
Jens Axboe
d3ad0aa424 mmc: need to zero sglist on init
Otherwise we could have junk in the sg fields, fooling
the sg chaining into thinking ->page is valid.

Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-16 11:24:45 +02:00
Linus Torvalds
65a6ec0d72 Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
  [ARM] 4578/1: CM-x270: PCMCIA support
  [ARM] 4577/1: ITE 8152 PCI bridge support
  [ARM] 4576/1: CM-X270 machine support
  [ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
  [ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
  [ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
  [ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
  [ARM] pxa: PXA3xx base support
  [NET] smc91x: fix PXA DMA support code
  [SERIAL] Fix console initialisation ordering
  [ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
  [ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
  [ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
  [ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
  [ARM] Rename consistent_sync() as dma_cache_maint()
  [ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
  [ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
  [ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
  [ARM] 4594/1: ns9xxx: use the new gpio functions
  [ARM] 4593/1: ns9xxx: implement generic clockevents
  ...
2007-10-15 16:08:50 -07:00
David Brownell
23fd50450a Fix compile while compiling drivers/mmc/host/mmc_spi.o with !BLOCK
Make sure the mmc_spi driver can build without CONFIG_BLOCK.
Issue noted by "Avuton Olrich" <avuton@gmail.com> and randconfig.

While that won't be a common configuration, sometimes embedded
boards use SDIO to interface WLAN or Bluetooth chips (vs some
parallel interface), and don't provide an MMC/SD socket for use
with flash memory cards.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-14 16:48:52 -07:00
Al Viro
7ac0326c3f uevent environment changes fallout
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-14 08:53:33 -07:00
Linus Torvalds
efefc6eb38 Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
  PM: merge device power-management source files
  sysfs: add copyrights
  kobject: update the copyrights
  kset: add some kerneldoc to help describe what these strange things are
  Driver core: rename ktype_edd and ktype_efivar
  Driver core: rename ktype_driver
  Driver core: rename ktype_device
  Driver core: rename ktype_class
  driver core: remove subsystem_init()
  sysfs: move sysfs file poll implementation to sysfs_open_dirent
  sysfs: implement sysfs_open_dirent
  sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
  sysfs: make sysfs_root a regular directory dirent
  sysfs: open code sysfs_attach_dentry()
  sysfs: make s_elem an anonymous union
  sysfs: make bin attr open get active reference of parent too
  sysfs: kill unnecessary NULL pointer check in sysfs_release()
  sysfs: kill unnecessary sysfs_get() in open paths
  sysfs: reposition sysfs_dirent->s_mode.
  sysfs: kill sysfs_update_file()
  ...
2007-10-12 15:49:37 -07:00
Kay Sievers
7eff2e7a8b Driver core: change add_uevent_var to use a struct
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.

Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.

Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:51:01 -07:00
Pierre Ossman
77f1fd6ecd mmc: use correct unregister function for led trigger
We register a simple trigger so make sure we use the corresponding
unregister function.

(Also means we get a dummy function when triggers aren't compiled in)

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-12 22:48:46 +02:00
Russell King
ebebd9b0a1 [ARM] pxa: update PXA MMC interface driver to use clk support
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-12 21:15:03 +01:00
Nicolas Pitre
019a5f56ec mmc: don't use weight32()
Using weight32() to determine if a value is a power of 2 is a rather
heavi weight solution.  The classic idiom is (x & (x - 1)) == 0, but
the kernel already provide a is_power_of_2 function for it.

Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-11 19:09:08 +02:00
Nicolas Pitre
c783837bc6 pxamci: support arbitrary block size
The PXA has two transmit FIFOes, each32 byte deep.  when one FIFO is
full and the other one has been transmitted, they are automatically
swapped and DMA is triggered for another 32 byte burst.  However, when
there is less than 32 bytes left to send, the FIFO swap has to be done
manually. This is required for some SDIO transfers which are not
required to be multiples of 32 bytes.

A DMA completion interrupt is set for each descriptor which length isn't
a multiple of 32 in order to force the FIFO swap.  While at it, the DMA
interrupt handler has been made a bit more resilient against errors.

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-10 20:13:29 +02:00
Nicolas Pitre
599473cf15 sdio: make the IRQ thread more resilient in the presence of bad states
Currently we print a message about some bad states wrt function IRQ
handlers but return 0 from process_sdio_pending_irqs() nevertheless.
This can lead to an infinite loop as nothing might have cleared the
condition for the pending card interrupt from the host controller by
the time host->ops->enable_sdio_irq(host, 1) is called.

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-06 17:51:45 +02:00
Nicolas Pitre
3e01e4bcdd sdio: fix IRQ diagnostic message
If func is actually null we won't get much from sdio_func_id(func).

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-06 17:48:57 +02:00
Pierre Ossman
d6f8deecef sdhci: remove old dma module params
The forcedma and nodma module parameters can be replaced with the quirks
parameter, so remove the redundancy.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-03 18:40:49 +02:00
Feng Tang
7c168e3db7 sdhci: add SDHCI_QUIRK_BROKEN_DMA quirk
Some controllers like ENE712 can't work properly with DMA mode,
add this quirk to force these kinds of HW work with PIO mode

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-03 18:40:33 +02:00
Feng Tang
56e71efe44 sdhci: remove DMA capability check from controller's PCI Class reg
Many host controllers don't fully follow the PCI spec to claim
whether they support DMA in PCI class register. Leave the driver
to judge it from the Capability register, quirks and module parameter

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-03 18:40:26 +02:00
Nicolas Pitre
2df3b71b27 sdhci: fix a typo
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-03 18:40:19 +02:00
Philip Langdale
5ae70296c8 mmc: Disabler for Ricoh MMC controller
Thanks to Matt Domsch and Rezwanul Kabir at Dell, we know how to disable the
MMC controller on the multi-function Ricoh R5C832. The MMC controller needs
to be disabled or it will steal MMC cards from the SD controller where they
would otherwise be supported by the Linux SDHCI driver.

Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-10-03 18:40:05 +02:00
Pierre Ossman
6f4285d133 sdio: adaptive interrupt polling
The interrupt polling frequency is a compromise between power usage and
interrupt latency. Unfortunately, it affects throughput rather severely
for devices which require an interrupt for every chunk of data.

By making the polling frequency adaptive, we get better throughput with
those devices without sacficing too much power. Polling will quickly
increase when there is an actual interrupt, and slowly fall back to the
idle frequency when the interrupts stop coming.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-27 10:48:29 +02:00
Bridge Wu
5d3ad4e8a1 mmc: pxamci: add SDIO card interrupt reporting capability
Again, only available from PXA27x.

Signed-off-by: Bridge Wu <mingqiao.wu@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-25 19:11:49 +02:00
Bridge Wu
df456f479a mmc: pxamci: set proper buswidth capabilities according to PXA flavor
From PXA27x, it is possible to do 4-bit data transfers.

Signed-off-by: Bridge Wu <mingqiao.wu@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-25 19:11:39 +02:00
Nicolas Pitre
fe2dc44eac mmc: pxamci: set proper block capabilities according to PXA flavor
From PXA27x, it is possible to do 2048-byte block transfers.

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-25 19:03:31 +02:00
Bridge Wu
81ab570f65 mmc: pxamci: better pending IRQ determination
Pending interrupts should be determined from both I_REG and I_MASK
registers.

Signed-off-by: Bridge Wu <mingqiao.wu@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-25 18:59:07 +02:00
Pavel Pisa
faf39ede5e arm: i.MX/MX1 SDHC implements SD cards read-only switch read-back
The patch enables to define MMC host get_ro() method through platform data.

Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-24 19:33:14 +02:00
Pierre Ossman
af8350c756 mmc: add led trigger
Add a led trigger for each host controller that indicates if there
is a request active on the controller.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-24 07:15:48 +02:00
David Brownell
15a0580ced mmc_spi host driver
This is the latest version of the MMC-over-SPI support.  It works
on 2.6.23-rc2 plus git-mmc (from rc1-mm2), along with the preceding
patches which teach the rest of the MMC stack about SPI.

The main issue of note is that sometimes cards need to be power cycled
to recover after certain faults.  Also, it may sometimes be necessary
to disable CRCs.  ("modprobe mmc_core use_spi_crc=n")

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: mikael.starvik@axis.com,
Cc: Hans-Peter Nilsson <hp@axis.com>
Cc: Jan Nikitenko <jan.nikitenko@gmail.com>
Cc: Mike Lavender <mike@steroidmicros.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 22:17:27 +02:00
David Brownell
af51715079 MMC core learns about SPI
Teach the MMC/SD/SDIO core about using SPI mode.

 - Use mmc_host_is_spi() so enumeration works through SPI signaling
   and protocols, not just the native versions.

 - Provide the SPI response type flags with each request issued,
   including requests from the new lock/unlock code.

 - Understand that cmd->resp[0] and mmc_get_status() results for SPI
   return different values than for "native" MMC/SD protocol; this
   affects resetting, checking card lock status, and some others.

 - Understand that some commands act a bit differently ... notably:
     * OP_COND command doesn't return the OCR
     * APP_CMD status doesn't have an R1_APP_CMD analogue

Those changes required some new and updated primitives:

 - Provide utilities to access two SPI-only requests, and one
   request that wasn't previously needed:
     * mmc_spi_read_ocr() ... SPI only
     * mmc_spi_set_crc() ... SPI only (override by module parm)
     * mmc_send_cid() ... for use without broadcast mode

 - Updated internal routines:
     * Previous mmc_send_csd() modified into mmc_send_cxd_native();
       it uses native "R2" responses, which include 16 bytes of data.
     * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
       helper for command-and-data access
     * Bugfix to that mmc_send_cxd_data() code:  dma-to-stack is
       unsafe/nonportable, so kmalloc a bounce buffer instead.

 - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper

 - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
   those helper routines based on whether they're native or SPI

The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI:  MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:51:30 +02:00
David Brownell
7213d175e3 MMC/SD card driver learns SPI
Teaching the MMC/SD block card driver about SPI.

 - Provide the SPI response type flags with each request issued.

 - Understand that multiblock SPI writes don't use STOP_TRANSMISSION.

 - Correct check for APP_CMD failure.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:39:47 +02:00
Pierre Ossman
759bdc7af4 sdio: store vendor strings
Store vendor strings found in CISTPL_VERS_1 so that function drivers
can access them.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:28:01 +02:00
Pierre Ossman
f9996aee36 mmc: increase power up delay
Increase delay for power up in order to support some slower boards.

Also add some comments about why the delays are there.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:26:06 +02:00
Pierre Ossman
f75979b77f sdhci: sdio interrupt support
Add support for relaying the sdio interrupt signal from the card.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:25:52 +02:00
Nicolas Pitre
15b82b46de sdio: fix recursion issues between sdio-uart driver and tty layer
In a few places, sdio_uart_irq() is called directly instead of waiting
for the actual interrupt to be raised and the SDIO IRQ thread scheduled
in order to reduce latency.  However, some interaction with the tty core
may end up calling us back (serial echo, flow control, etc.) creating
two issues:

 - the host lock gets claimed twice from the same thread causing a
   deadlock;

 - the same direct calls to sdio_uart_irq() may be performed causing
   unexpected reentrancy into the IRQ handler.

This patch handles both of those issues.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:24:52 +02:00
Nicolas Pitre
2ba30eedec sdio: add default c_ispeed/c_ospeed values to sdio_uart driver
Note that the default baudrate is 4800 instead of 9600 as a convenience
because that's what GPS devices want which is still the main use for
this driver.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:24:48 +02:00
David Vrabel
7806cdb40f sdio: add sdio_f0_readb() and sdio_f0_writeb()
Add sdio_f0_readb() and sdio_f0_writeb() functions to reading and
writing function 0 registers.  Writes outside the vendor specific CCCR
registers (0xF0 - 0xFF) are not permitted.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:24:27 +02:00
Pierre Ossman
d84075c8ae mmc: replace BUG_ON with WARN_ON
Replace all cases of BUG_ON with WARN_ON where there is a chance
(with varying degrees of slim) that the kernel can continue without
incidence.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:23:07 +02:00
Mariusz Kozlowski
9f2fcf9939 sdio: kmalloc + memset conversion to kzalloc
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:22:45 +02:00
David Vrabel
eb65946892 sdio: extend sdio_readsb() and friends to handle any length of buffer
Extend sdio_readsb(), sdio_writesb(), sdio_memcpy_fromio(), and
sdio_memcpy_toio() to handle any length of buffer by splitting the transfer
into several IO_RW_EXTENDED commands. Typically, a transfer would be split
into a single block mode transfer followed by a byte mode transfer for the
remainder but we also handle lack of block mode support and the block size
being greater than 512 (the maximum byte mode transfer size).

host->max_seg_size <= host->max_req_size so there's no need to check both
when determining the maximum data size for a single command.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:21:32 +02:00
David Vrabel
9a08f82b3c sdio: set the functions' block size
Before a driver is probed, set the function's block size to the default so the
driver is sure the block size is something sensible and it needn't explicitly
set it.

The default block size is the largest that's supported by both the card and
the host, with a maximum of 512 to ensure aribitrarily sized transfer use the
optimal (least) number of commands.

See http://lkml.org/lkml/2007/8/7/150 for reasons for the block size choice.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:19:26 +02:00
David Vrabel
7616ee95f2 sdio: add SDIO_FBR_BASE(f) macro
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:16:27 +02:00
Pierre Ossman
e6f918bf39 mmc: fix sdio timeout calculation
SDIO doesn't have a CSD so it uses different timeout values than
SD memory.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:16:01 +02:00
Pierre Ossman
ce252edd86 mmc: fix incorrect divisor in debug output
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:15:45 +02:00
Pierre Ossman
4ff6471c02 sdio: enable wide bus mode
Enable 4-bit data bus mode, according to host and card
capabilities.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:15:16 +02:00
Pierre Ossman
6db5020e73 sdio: change clock speed
Change clock speed to the highest supported by the card.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:14:09 +02:00
Adrian Bunk
22bfc979d3 make struct sdio_dev_attrs[] static
On Wed, Jul 25, 2007 at 04:03:04AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.22-rc6-mm1:
>...
>  git-mmc.patch
>...
>  git trees
>...

sdio_dev_attrs[] can become static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:13:32 +02:00
Nicolas Pitre
17b759aff9 sdio: add interface for host side SDIO interrupt reporting
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:13:08 +02:00
Pierre Ossman
112c9db91e sdio: support IO_RW_EXTENDED
Support the multi-byte transfer operation, including handlers for
common operations like writel()/readl().

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:09:34 +02:00
Nicolas Pitre
5ed334a1f8 sdio: add /proc interface to sdio_uart driver
This mimics what the serial_core does.  Useful for diagnostics.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:02:57 +02:00
Nicolas Pitre
6e418a9d26 sdio: UART/GPS driver
This currently only accepts the GPS class since that's all I have for
testing.  Tested with a Matsushita GPS and gpsd version 2.34.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:02:45 +02:00
Nicolas Pitre
d1496c39e5 sdio: core support for SDIO function interrupt
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:01:33 +02:00
Nicolas Pitre
2342f3323c sdio: allow for mmc_claim_host to be aborted
It is sometimes necessary to give up on trying to claim the host lock,
especially if that happens in a thread that has to be stopped.

While at it, fix the description for mmc_claim_host() which was wrong.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:55:13 +02:00
Pierre Ossman
bcfe66e21e sdio: add basic sysfs attributes
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:54:15 +02:00
Pierre Ossman
d59b66c7a5 sdio: add modalias support
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:53:33 +02:00
Pierre Ossman
9eb3a94d02 mmc: whip bus uevent handler into shape
Make the mmc bus uevent callback look like all other subsystems.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:52:20 +02:00
Pierre Ossman
3b38bea0d9 sdio: add device id table and matching
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:51:27 +02:00
Nicolas Pitre
26074962e8 mmc: initialize mmc subsystem with subsys_initcall()
The problem is that the sdio_bus must be registered before any SDIO
drivers are registered against it otherwise the kernel sulks.  Because
the sdio_bus registration happens through module_init (equivalent to
device_initcall), then any SDIO
drivers linked before the SDIO core code in the kernel will be initialized
first.

Upcoming SDIO function drivers are likely to be located outside the
drivers/mmc directory as it is common practice to group drivers according
to their function rather than the bus they use.  SDIO drivers are therefore
likely to appear at random location in the kernel link.

To make sure the sdio_bus is always initialized before any SDIO drivers,
let's move the MMC init to the subsys_initcall level.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:45:39 +02:00
Pierre Ossman
1a632f8cdc sdio: split up common and function CIS parsing
Add a more clean separation between global, common CIS information
and the function specific one as we need the common information in
places where no specific function is specified.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:44:22 +02:00
Nicolas Pitre
b1538bcf75 sdio: link unknown CIS tuples to the sdio_func structure
This way those tuples that the core cares about are consumed by the core
code, and tuples that only function drivers might make sense of are
available to drivers.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:31:43 +02:00
Nicolas Pitre
b726126196 sdio: initial CIS parsing code
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:26:42 +02:00
Pierre Ossman
0597007f1b sdio: basic parsing of FBR
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:13:52 +02:00
Pierre Ossman
35c66c1908 sdio: read and decode interesting parts of the CCCR
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:12:18 +02:00
Pierre Ossman
fa64efa1f2 mmc: enable/disable functions for SDIO
Like many other buses, the devices (functions) on the SDIO bus
must be enabled before they can be used. Add functions that allow
drivers to do so.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:10:56 +02:00
Pierre Ossman
46f555f273 mmc: add basic SDIO I/O operations
Add command wrappers that simplify register access from SDIO
function drivers.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:57:03 +02:00
Pierre Ossman
f76c85154d mmc: add SDIO driver handling
Add basic driver handling to the SDIO device model.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:55:26 +02:00
Pierre Ossman
e29a7d73f4 mmc: basic SDIO device model
Add the sdio bus type and basic device handling.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:45:31 +02:00
Pierre Ossman
b2bcc798bb mmc: implement SDIO IO_RW_DIRECT operation
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:42:37 +02:00
Pierre Ossman
5c4e6f1301 mmc: detect SDIO cards
Really basic init sequence for SDIO cards.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:40:07 +02:00
Marc Pignat
1d4de9edd6 mmc: at91_mci: disable handling of blocks with size not multiple of 4 bytes
This kind of transfer is not supported, so don't advertise it and make it
fail early.

Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:29:34 +02:00
Pierre Ossman
8fdd8521dc mmc: add missing printk levels
Some printk:s were missing an explicit level.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 09:15:22 +02:00
Pierre Ossman
be0192aae1 mmc: remove confusing flag
The MMC_DATA_MULTI flag never had a proper definition of what it
means, so remove it and let the drivers check the block count in
the request.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 09:15:12 +02:00
Pierre Ossman
255d01af9a mmc: remove BYTEBLOCK capability
Remove the BYTEBLOCK capability and let the broken hosts fail the
requests with -EINVAL instead.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 09:15:05 +02:00
Pierre Ossman
b146d26a61 mmc: mmc_set_data_timeout() parameter write is redundant
The write parameter in mmc_set_data_timeout() is redundant as the
data structure contains information about the direction of the
transfer.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 09:15:00 +02:00
Pierre Ossman
d7604d7635 mmc: read ext_csd version number
Make sure we do not try to parse a structure we do not
understand.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 09:14:53 +02:00
Pierre Ossman
adf66a0dc5 mmc: improve error code feedback
Now that we use "normal" error codes, improve the reporting and response
to error codes in the core.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 09:14:43 +02:00
Pierre Ossman
17b0429dde mmc: remove custom error codes
Convert the MMC layer to use standard error codes and not its own,
incompatible values.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 08:46:48 +02:00
Anti Sullin
e0cda54e44 bug in AT91 MCI suspend routines
This patch fixes a bug in AT91 mmc host driver, that enables the wakeup
from suspend on card detection pin even if the card detect pin is not
available (==0). If not card detection pin is defined, IRQ0 == FIQ gets
enabled and if some activity is present on that pin, the system gets a
FIQ request, that causes a crash.

Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-11 17:21:51 +02:00
Pierre Ossman
b67ac3f339 sdhci: tell which spurious interrupt we got
When we get unexpected interrupts, also print which interrupt it was.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:31:07 +02:00
Pierre Ossman
e538fbe83e sdhci: handle data interrupts during command
It is fully legal for a controller to start issuing data related
interrupts before it has signalled that the command has completed.
Make sure the driver actually can handle this.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:30:53 +02:00
David Vrabel
03f8590d90 mmc: ignore bad max block size in sdhci
Some SDHC cards report an invalid maximum block size, in these cases
assume they support block sizes up to 512 bytes instead of returning
an error.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:27:50 +02:00
Pierre Ossman
2b06197340 sdhci: be more cautious about block count register
The block count register shouldn't be trusted for single block transfers,
so avoid using it completely when calculating transferred bytes.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:27:44 +02:00
Mariusz Kozlowski
be760a9de8 drivers/mmc/core/host.c: kmalloc + memset conversion to kzalloc
drivers/mmc/core/host.c | 3509 -> 3457 (-52 bytes)
 drivers/mmc/core/host.o | 92400 -> 92136 (-264 bytes)

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:26:31 +02:00
Mariusz Kozlowski
733cb1e440 drivers/mmc/core/bus.c: kmalloc + memset conversion to kzalloc
drivers/mmc/core/bus.c | 5663 -> 5619 (-44 bytes)
 drivers/mmc/core/bus.o | 70899 -> 70731 (-168 bytes)

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-23 06:26:26 +02:00
Nicolas Ferre
37b758e8bc mmc: at91_mci: remove whitespace at the end of lines
Some cleanup with whitespace/tab at the end of lines.

Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-09 16:13:44 +02:00
Pierre Ossman
aafabfab26 mmc: reorganize bounce buffer init
Reorganize the code that initializes mmc_block's bounce buffer in
order to avoid warnings when MMC_BLOCK_BOUNCE isn't used.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-09 14:37:17 +02:00
Gabriel C
b3627bb19f wbsd: fix section mismatch warnings
This patch fixes the following section mismatch warnings

...

WARNING: vmlinux.o(.init.text+0x29d40): Section mismatch: reference to .exit.text:wbsd_release_resources (between 'wbsd_init' and 'wbsd_probe')
WARNING: vmlinux.o(.init.text+0x29d49): Section mismatch: reference to .exit.text:wbsd_free_mmc (between 'wbsd_init' and 'wbsd_probe')
WARNING: vmlinux.o(.init.text+0x29f28): Section mismatch: reference to .exit.text:wbsd_free_mmc (between 'wbsd_init' and 'wbsd_probe')

...

Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-09 14:37:10 +02:00