User registers have different alignments on different chips (4KB on
older, 64KB on 7220). Allow mapping the user registers on kernels with
page sizes up to 64K.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Various hardware counters are exported via the ipath file system (since
it is binary data). The old file format was very dependent on the HW
offsets for these registers. Newer HCA chips can have different
counters at different offsets. This patch adds a level of indirection
to make the file format consistent across HCAs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for QLogic HCAs which have hardware performance sampling
registers for PortSamplesControl and PortSamplesResult MADs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When you have multiple targets, it gets really confusing when you try
to track down who did a reset when there is no identifying information
in the log message, especially when the same extension ID is mapped
through two different local IB ports. So, add an identifier that can
be used to track back to which local IB port/remote target pair is the
one having problems.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Acked-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some HCAs (such as ehca2) support SRQ, but only support fewer than 16 SG
entries for SRQs. Currently IPoIB/CM implicitly assumes all HCAs will
support 16 SG entries for SRQs (to handle a 64K MTU with 4K pages). This
patch removes that restriction by limiting the maximum MTU in connected
mode to what the maximum number of SRQ SG entries allows.
This patch addresses <https://bugs.openfabrics.org/show_bug.cgi?id=728>
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
By default, the SCSI mid-layer seems to send down 512KB requests
(sg_tablesize = 256), with some requests occasionally combined. By
allowing the mid-layer to chain requests, we can easily grow to 1024KB
or larger -- I've tested 4096KB I/O requests with no problems.
I looked through the DMA paths on the hardware drivers to ensure they
could take advantage of the SG chaining, and it seems that every one
except ipath uses the system's DMA routines, which have been converted
to handle chaining. ipath looks like it should be OK, but I have no
way to test it.
Signed-off-by: David Dillow <dillowda@ornl.gov>
[ Tested on ipath. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current SRP initiator will send requests even if it has no credits
available. The results of sending extra requests are vendor specific,
but on some devices, overrunning credits will cost 85% of peak
performance -- e.g. 100 MB/s vs 720 MB/s. Other devices may just drop
the requests.
This patch will tell the SCSI midlayer to queue requests if there are
fewer than two credits remaining, and will not issue a task management
request if there are no credits remaining. The mid-layer will retry
the queued command once an outstanding command completes.
The patch also removes the unlikely() in __srp_get_tx_iu(), as it is
not at all unlikely to hit this limit under heavy load.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An IPoIB subnet on an IB fabric that spans multiple IB subnets can't
use link-local scope in multicast GIDs. The existing routines that
map IP/IPv6 multicast addresses into IB link-level addresses hard-code
the scope to link-local, and they also leave the partition key field
uninitialised. This patch adds a parameter (the link-level broadcast
address) to the mapping routines, allowing them to initialise both the
scope and the P_Key appropriately, and fixes up the call sites.
The next step will be to add a way to configure the scope for an IPoIB
interface.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch moves some arrays that were defined per-device to be
variables defined in the per context data structure, thus avoiding extra
kzalloc() calls.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In preparation for upcoming chips that have different values for
INFINIPATH_R_PORTENABLE_SHIFT, INFINIPATH_R_INTRAVAIL_SHIFT,
INFINIPATH_R_TAILUPD_SHIFT, and portcfg_shift, remove the shared
#defines and use device-specific variables instead.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
kreceive is now portdata * instead of devdata * and other kreceive
related cleanups....
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove an unused parameter and fix up the comment.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a couple of minor problems with RNR NAK handling:
- The insertion sort was causing extra delay when inserting ahead
vs. behind an existing entry on the list.
- A resend of a first packet of a message which is still not ready,
needs another RNR NAK (i.e., it was suppressed when it shouldn't).
- Also, the resend tasklet doesn't need to be woken up unless the
ACK/NAK actually indicates progress has been made.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows ehca to forward event client-reregister-required to
registered clients. One such event is generated by a switch eg. after
its reboot.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than byte-swapping cqe->g_mlpath_rqpn each time we extract a
field from it, byte-swap it once into a temporary variable. This
results in smaller, better code -- eg, on 32-bit x86:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-5 (-5)
function old new delta
mlx4_ib_poll_cq 1188 1183 -5
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove MSI support from the mthca driver, as scheduled. There is no
reason to use MSI instead of MSI-X, since MSI-X performs better. No
one has spoken up since MSI support was deprecated in commit f6be6fbe
("IB/mthca: Schedule MSI support for removal"), so apparently the MSI
support is unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is based on user feedback from Doug Ledford at RedHat:
Events that occur on an rdma_cm_id are reported to userspace through an
event channel. Connection request events are reported on the event
channel associated with the listen. When the connection is accepted, a
new rdma_cm_id is created and automatically uses the listen event
channel. This is suboptimal where the user only wants listen events on
that channel.
Additionally, it may be desirable to have events related to connection
establishment use a different event channel than those related to
already established connections.
Allow the user to migrate an rdma_cm_id between event channels. All
pending events associated with the rdma_cm_id are moved to the new event
channel.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable conn_id remove on the passive side after connection
establishment. This corrects an issue where the IB driver can't be
unloaded after running applications over RDS. The 'dev_remove' counter
does not reach 0 for established connections on the passive side.
This problem is limited to device removal, and only occurs on the
passive side if there are established connections.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In cancel_mads(), MADs are moved from the wait_list and local_list
to a cancel_list for processing. However, the structures on these two
lists are not the same. The wait_list references struct
ib_mad_send_wr_private, but local_list references struct
ib_mad_local_private. Cancel_mads() treats all items moved to the
cancel_list as struct ib_mad_send_wr_private. This leads to a system
crash when requests are moved from the local_list to the cancel_list.
Fix this by leaving local_list alone. All requests on the local_list
have completed are just awaiting processing by a queued worker thread.
Bug (crash) reported by Dotan Barak <dotanb@dev.mellanox.co.il>.
Problem with local_list access reported by Robert Reynolds
<rreynolds@opengridcomputing.com>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add performance/debug counters to track sent/received messages, retries,
and duplicates. Counters are tracked per CM message type, per port.
The counters are always enabled, so intrusive state tracking is not done.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To allow ULPs to tune timeout values and capture retry statistics,
report the number of times that a mad send operation was retried.
For RMPP mads, report the total number of times that the any portion
(send window) of the send operation was retried.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
P_key changes can invalidate multicast groups. Report errors on all
multicast groups affected by a pkey change.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add the work completion error code to the QP error debug output.
This makes it easier to determine the cause of the error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An internal code review found the comment here lacking -- update it with
more specifics of how and why the rmb() is there.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a code review, someone noticed the comments didn't match the code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The gen2_basic tests check for the errno value when a CQ is resized
smaller than the number of outstanding completions queue on the CQ.
This patch changes ib_ipath to return EINVAL which is what ib_mthca
returns and what gen2_basic expects.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Code review pointed out that the locking around uses of ipath_sendctrl
and kr_sendctrl were, in several places, incorrect and/or inconsistent.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At one point in time there was code to allow a user process to
wait for a send buffer if none were available. This feature was
never used and most of the code was removed. This removes
some missed unused code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The 5.0 firmware now supports translating sgls in recv work requests,
so remove the host driver logic currently doing the translation.
Note: this change requires 5.0 firmware.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently the call into cxgb3 to get the driver info is not serialized.
The iw_cxgb3 module needs to hold the rtnl_lock around the ethtool ops
call like dev_ioctl() does.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Tested-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The local loopback of an outgoing DR SMP response is limited to those
that originate at the driver specific SMA implementation during the
driver specific process_mad() function. This patch enables a
returning DR SMP originating in userspace (or elsewhere) to be
delivered to the local managment stack. In this specific case the
driver process_mad() function does not consume or process the MAD, so
a reponse mad has not be created and the original MAD must manually be
copied to the MAD buffer that is to be handed off to the local agent.
Signed-off-by: Steve Welch <swelch@systemfabricworks.com>
Acked-by: Hal Rosenstock <hal@xsigo.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch is in response to reviewing a patch to the core MAD
processing which fixes loopback of directed route packets to/from user
level MAD agents. This change enables the core code to work for
ib_ipath by fixing the return code from the ipath process_mad method.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In ib_mad_recv_done_handler(), the response pointer is checked for
NULL after allocating it. It is then checked again in the local
process_mad() path but there is no possibility of it changing in
between.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Acked-by: Hal Rosenstock <hal@xsigo.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the initiator depth and responder resources to the device max
values for new connect request events in the iWARP connection manager.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve interrupt handler cache footprint by noinline'ing error
functions that are rarely called.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some IB adapters (notably IBM's eHCA) do not implement SRQs (shared
receive queues). The current IPoIB connected mode support only works
on devices that support SRQs.
Fix this by adding support for using the receive queue of each
connected mode receive QP. The disadvantage of this compared to using
an SRQ is that it means a full queue of receives must be posted for
each remote connected mode peer, which means that total memory usage
is potentially much higher than when using SRQs. To manage this, add
a new module parameter "max_nonsrq_conn_qp" that limits the number of
connections allowed per interface.
The rest of the changes are fairly straightforward: we use a table of
struct ipoib_cm_rx to hold all the active connections, and put the
table index of the connection in the high bits of receive WR IDs.
This is needed because we cannot rely on the struct ib_wc.qp field for
non-SRQ receive completions. Most of the rest of the changes just
test whether or not an SRQ is available, and post receives or find
received packets in the right place depending on the answer.
Cleaning up dead connections actually becomes simpler, because we do
not have to do the "last WQE reached" dance that is required to
destroy QPs attached to an SRQ. We just move the QP to the error
state and wait for all pending receives to be flushed.
Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
[ Completely rewritten and split up, based on Pradeep's work. Several
bugs fixed and no doubt several bugs introduced. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out the code for going through the rx_reap list of struct
ipoib_cm_rx and freeing each one. This consolidates the code
duplicated between ipoib_cm_dev_stop() and ipoib_cm_rx_reap() and
reduces the risk of error when adding additional accounting.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out the code to create an SRQ and allocate the receive ring in
ipoib_cm_dev_init() into a new function ipoib_cm_create_srq(). This
will make the code neater when support for devices that don't implement
SRQs is added.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out the code to unmap/free skbs and free the receive ring in
ipoib_cm_dev_cleanup() into a new function ipoib_cm_free_rx_ring().
This function will be called from a couple of other places when
support for devices that don't implement SRQs is added.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 23b9c1ab ("Infiniband: make ipath driver use default driver
groups.") introduced a bug in the ipath driver where
ipath_device_create_group() fell through into the error path, even on
success, which meant that the sysfs groups it created would always get
removed right away. This made ipath_device_remove_group() hit the
BUG_ON() in sysfs_remove_group() when it tried to remove those groups a
second time.
Correct the return path so that the groups stick around until they are
supposed to be cleaned up.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the ipath driver use the new driver functions so that it does not
touch the sysfs portion of the driver structure.
We also remove the redundant symlink from the device back to the driver,
as it is already in the sysfs tree. Any userspace tools should be using
the standard symlink, not some driver specific one.
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Arthur Jones <arthur.jones@qlogic.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
