Commit Graph

870 Commits

Author SHA1 Message Date
Benjamin Herrenschmidt
ecca1a34be Merge commit 'kumar/next' into next
Conflicts:
	arch/powerpc/sysdev/fsl_msi.c
2010-05-31 10:01:50 +10:00
Benjamin Herrenschmidt
3d00d4ff11 Merge commit 'jwb/next' into next 2010-05-31 09:59:00 +10:00
Haiying Wang
48936a08b8 powerpc/85xx: Add P1021MDS board support
P1021 is a dual e500v2 core based SOC with:
* 3 eTSECs (eTSEC1/3 RGMII, eTSEC2 SGMII on this board)
* 2 PCIe Controller
* 1 USB2.0 controller
* eSDHC, eSPI, I2C, DUART
* eLBC (NAND, BCSR, PMC0/1)
* Security Engine (SEC 3.3.2)
* Quicc Engine (QE)

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Yu Liu <Yu.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-24 21:29:25 -05:00
Li Yang
710e338326 powerpc/85xx: Change MPC8572DS camp dtses for MSI sharing
Enable the sharing of MSI interrupt through AMP OSes in the mpc8572ds
dtses.

Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-24 21:26:36 -05:00
Andy Fleming
0472fd0755 powerpc/85xx: Enable support for ports 3 and 4 on 8548 CDS
I believe support was disabled due to issues with earlier versions of
the board/processor.  At worst, adding the ports back into the device
tree should result in enabling ports that don't work on older systems,
so the default should be to enable them.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-21 07:41:54 -05:00
Anton Vorontsov
6971df4f5b powerpc/83xx: Add MCU LEDs support for MPC837xRDB and MPC8315RDB boards
There are two front-panel LEDs on MPC837xRDB and MPC8315RDB boards: PWR
and HDD. After adding appropriate nodes we can program these LEDs from
kernel and user space.

Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-17 10:55:32 -05:00
Anton Vorontsov
0aedc00851 powerpc/85xx: Fix P1020RDB boot hang due USB2
Since USB2 is shared with local bus, either local bus or USB2
should be disabled. By default U-Boot enables local bus, so we
have to disable USB2, otherwise kernel hangs:

 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
 fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
 fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
 hub 1-0:1.0: USB hub found
 hub 1-0:1.0: 1 port detected
 fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
 fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
 <hangs here>

Note that U-Boot doesn't clear 'status' property when it enables
USB2, so we have to comment out the whole node.

To enable USB2, one can issue
'setenv hwconfig usb2:dr_mode=<host|peripheral>' command at the
U-Boot prompt.

Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-17 10:55:29 -05:00
Anton Vorontsov
7541ef78c3 powerpc/85xx: Add eTSEC 2.0 support for P1020RDB boards
This patch adds support for eTSEC 2.0 as found in P1020.
The changes include introduction of the group nodes for
the etsec nodes.

Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-17 10:52:45 -05:00
Kim Phillips
18f397c838 powerpc: remove tls_ssl_stream descriptor type capability in sec3.3 node
Technically, whilst SEC v3.3 h/w honours the tls_ssl_stream descriptor
type, it lacks the ARC4 algorithm execution unit required to be able
to execute anything meaningful with it.  Change the node to agree with
the documentation that declares that the sec3.3 really doesn't have such
a descriptor type.

Reported-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-17 10:51:17 -05:00
Stefan Roese
a89eda2675 powerpc/44x: Add basic ICON PPC440SPe board support
ICON is based on the AppliedMicro 440SPe. It is equipped with
64MByte NOR FLASH, SODIMM, Gigabit ethernet, SM502 on PCI(X),
LSI SAS1068E on PCIe0 and custom FPGA on PCIe1.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-05-12 07:50:53 -04:00
Benjamin Herrenschmidt
58645c7f36 powerpc/44x: Fix UART clocks on 440SPe
The code to fixup the serial ports on 440SPe uses the incorrect
addresses for these. This fixes it.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-05-12 07:48:49 -04:00
Stefan Roese
499f49026e powerpc/44x: Add reset-type to katmai.dts
Katmai needs "reset-type" = "chip reset" (2) to correctly reboot the
board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-05-07 15:07:29 -04:00
Tirumala Marri
e2efc09e52 powerpc/44x: Adding PCI-E support for PowerPC 460SX based SOC.
Add support for PCI-e on the AMCC 460SX boards

Signed-off-by: Tirumala Marri <tmarri@amcc.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-05-07 15:07:19 -04:00
Torez Smith
b4e8c8dd84 powerpc/4xx: Simple platform for the ISS 4xx simulator
This is a trivial 4xx plaform that uses the new simple bsp from
Josh and is handy to use in simulators such as ISS or even Mambo
who don't properly implement most of the actual devices in the
SoC but really only the core.

Signed-off-by: Torez Smith  <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-05-05 11:11:56 -04:00
Corey Minyard
58706ef96f powerpc: Add a new zImage for maple using a different link address
The maple platform failed to load because it's firmware could not take a
link address of 0x4000000.  A new platform type with a link address of
0x400000 had to be created for the maple.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2010-04-07 14:12:36 +10:00
Linus Torvalds
b6fedfd2a1 Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/booke: Fix breakpoint/watchpoint one-shot behavior
  powerpc: Reduce printk from pseries_mach_cpu_die()
  powerpc: Move checks in pseries_mach_cpu_die()
  powerpc: Reset kernel stack on cpu online from cede state
  powerpc: Fix G5 thermal shutdown
  powerpc/pseries: Pass CPPR value to H_XIRR hcall
  powerpc/booke: Fix a couple typos in the advanced ptrace code
  powerpc: Fix SMP build with disabled CPU hotplugging.
  powerpc: Dynamically allocate pacas
  powerpc/perf: e500 support
  powerpc/perf: Build callchain code regardless of hardware event support.
  powerpc/cpm2: Checkpatch cleanup
  powerpc/86xx: Renaming following split of GE Fanuc joint venture
  powerpc/86xx: Convert gef_pic_lock to raw_spinlock
  powerpc/qe: Convert qe_ic_lock to raw_spinlock
  powerpc/82xx: Convert pci_pic_lock to raw_spinlock
  powerpc/85xx: Convert socrates_fpga_pic_lock to raw_spinlock
2010-03-12 16:06:51 -08:00
Benjamin Herrenschmidt
59603b9ae4 Merge commit 'kumar/next' into merge 2010-03-09 11:51:57 +11:00
Jiri Kosina
318ae2edc3 Merge branch 'for-next' into for-linus
Conflicts:
	Documentation/filesystems/proc.txt
	arch/arm/mach-u300/include/mach/debug-macro.S
	drivers/net/qlge/qlge_ethtool.c
	drivers/net/qlge/qlge_main.c
	drivers/net/typhoon.c
2010-03-08 16:55:37 +01:00
Martyn Welch
948e78c3fc powerpc/86xx: Renaming following split of GE Fanuc joint venture
This patch renames GE Fanuc boards following the split-up of the GE Fanuc
joint venture. These boards are now made by GE Intelligent platorms.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-03-04 10:43:44 -06:00
David S. Miller
47871889c6 Merge branch 'master' of /home/davem/src/GIT/linux-2.6/
Conflicts:
	drivers/firmware/iscsi_ibft.c
2010-02-28 19:23:06 -08:00
Benjamin Herrenschmidt
87d31345c0 Merge commit 'gcl/next' into next 2010-02-19 14:38:23 +11:00
Anton Vorontsov
e98efaf303 powerpc/85xx: Add NOR, LEDs and PIB support for MPC8568E-MDS boards
This patch adds NOR Flash, LEDs and PIB support for MPC8568E-MDS
boards. Plus, move bcsr node into localbus node, and add bcsr5
gpio-controller node.

Some platform code modifications were also needed.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-02-17 21:48:24 -06:00
Malcolm Crossley
41cbdeef37 powerpc/86xx: Add MSI section to GE PPC9A DTS
Add the MSI section to the DTS file for the GE PPC9A.

Signed-off-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-02-17 21:48:21 -06:00
Martyn Welch
ae1f7553b9 powerpc/86xx: Basic flash support for GE SBC610
Support for the SBC610 VPX Single Board Computer from GE (PowerPC MPC8641D).

This patch adds basic support for the on-board flash.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-02-17 21:48:05 -06:00
Malcolm Crossley
6459ba984a powerpc/86xx: Add MSI section to GE SBC610 DTS
Add the MSI section to the DTS file for the GE SBC610.

Signed-off-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-02-17 21:17:07 -06:00
Malcolm Crossley
9b952a3970 powerpc/86xx: Fix GE SBC310 XMC site support
Correction to interrupt map mask for GE SBC310 XMC site and addition of
alias.

Signed-off-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-02-17 21:17:05 -06:00
Martyn Welch
f5d570d32c powerpc/86xx: Add MSI section to GE SBC310 DTS
Add the MSI section to the DTS file for the GE SBC310.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-02-17 21:17:03 -06:00
Anatolij Gustschin
d24720a45a powerpc/mpc5121: correct DIU compatible property
The DIU driver should bind against "fsl,mpc5121-diu"
directly. Add this compatible property to the match
table and fix DTS and platform code accordingly.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-02-17 07:33:22 -07:00
Anatolij Gustschin
dcc79d7870 powerpc/mpc5121: update mpc5121ads DTS
Collects several changes needed after applying
previous mpc5121 platform and driver patches:

- Add mpc5121 reset module node
- Clean up and fix NAND description, remove unused properties
  here and correct NAND flash chip size.
- Clean up I2C nodes: remove obsolete "cell-index" properties,
  add "fsl,preserve-clocking" property
- Add I2C RTC node for m41t61 RTC
- Add I2C nodes for AD7414 temperature sensor and AT24C32CD3 EEPROM
- Fix compatible property in DMA node
- Clean up CAN nodes, remove unused "cell-index" properties
- Fix compatible property in DIU node
- USB node changes:
    - use "fsl,mpc5121-usb2-dr" compatible property only
    - remove "port0" and "port1" properties as these are only used
      for multi-port host(MHP) module which is not available
      on MPC5121.
    - use 'fsl,invert-drvvbus' and 'fsl,invert-pwr-fault' in
      USB node for internal PHY to specify polarities
      of the appropriate port pins.

Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-02-16 11:12:04 -07:00
Stefan Roese
5a6543e8da powerpc/44x: Update Glacier dts
Sync Glacier dts with latest Canyonlands version:

- Add l2 cache support
- Add NDFC support
- Add RTC support
- Add AD7414 hwmon support
- Change EMAC compatible node from emac4 to emac4sync and correct the
  register size
- Add support for ISA holes on 4xx PCI/X/E
  (as done in Benjamin Herrenschmidt's patch for Canyonlands)
- Add Crypto device node

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-02-10 08:21:17 -05:00
Stefan Roese
6f57518cfa powerpc/44x: Update Arches dts
Sync Arches dts with latest Canyonlands version:

- Add 16k FIFO size to supported EMAC nodes
- Add next-level-cache property
- Add Crypto device node

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-02-10 08:21:16 -05:00
Stefan Roese
036f290d89 powerpc/44x: Add MTD support (NOR FLASH) to Katmai dts
This patch adds NOR FLASH MTD support to the Katmai (440SPe) dts file.
For this the OPB ranges address is mapped differently (base 0x00000000
-> 0xe0000000). This results in the address being identical to the lower
32bit of its physical address. This is needed for the MTD mapping to work
correctly, since U-Boot will insert the physical addresses of the EBC
chip selects into the EBC ranges property. This is the way its done in
most other 4xx dts files as well.

Additionally with a small whitespace cleanup.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-02-10 08:21:15 -05:00
Daniel Mack
3ad2f3fbb9 tree-wide: Assorted spelling fixes
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-02-09 11:13:56 +01:00
David S. Miller
51c24aaaca Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2010-01-23 00:31:06 -08:00
Liu Yu-B13201
d03e067778 dts/mpc8569mds: Cleanup tbi phy to support rtbi
After these change, when need to work in rtbi mode,
just change phy-connection-type to "rtbi".

Also, this work can be done by u-boot.

Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-21 01:17:54 -08:00
Peter Tyser
3f884bf54d powerpc: Use scripts/mkuboot.sh instead of 'mkimage'
mkuboot.sh provides a basic wrapper for the 'mkimage' utility.  Using
mkuboot.sh provides clearer error reporting and allows a toolchain to
use its own 'mkimage' executable specified by ${CROSS_COMPILE}mkimage.
Additionally, this brings PowerPC in line with other architectures
which already call mkimage via mkuboot.sh.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-30 15:23:26 -07:00
Benjamin Herrenschmidt
8beac08ee9 Merge commit 'jwb/next' into merge 2009-12-21 09:30:45 +11:00
Benjamin Herrenschmidt
2593f939a5 Merge commit 'kumar/next' into merge 2009-12-21 09:30:42 +11:00
Albert Herranz
698cd335a7 powerpc/gamecube/wii: Fix off-by-one error in ugecon/usbgecko_udbg
The retry logic in ug_putc() is broken.

If the TX fifo is not ready and the counter runs out it will have a
value of -1 and no transfer should be attempted. Also, a counter
with a value of 0 means that the TX fifo got ready in the last try
and the transfer should be attempted.

Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-12-18 15:13:57 +11:00
Linus Torvalds
a73611b6aa Merge branch 'next' of git://git.secretlab.ca/git/linux-2.6
* 'next' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
  powerpc: fix up for mmu_mapin_ram api change
  powerpc: wii: allow ioremap within the memory hole
  powerpc: allow ioremap within reserved memory regions
  wii: use both mem1 and mem2 as ram
  wii: bootwrapper: add fixup to calc useable mem2
  powerpc: gamecube/wii: early debugging using usbgecko
  powerpc: reserve fixmap entries for early debug
  powerpc: wii: default config
  powerpc: wii: platform support
  powerpc: wii: hollywood interrupt controller support
  powerpc: broadway processor support
  powerpc: wii: bootwrapper bits
  powerpc: wii: device tree
  powerpc: gamecube: default config
  powerpc: gamecube: platform support
  powerpc: gamecube/wii: flipper interrupt controller support
  powerpc: gamecube/wii: udbg support for usbgecko
  powerpc: gamecube/wii: do not include PCI support
  powerpc: gamecube/wii: declare as non-coherent platforms
  powerpc: gamecube/wii: introduce GAMECUBE_COMMON
  ...

Fix up conflicts in arch/powerpc/mm/fsl_booke_mmu.c.

Hopefully even close to correctly.
2009-12-16 13:26:53 -08:00
Albert Herranz
02d748a9ee wii: bootwrapper: add fixup to calc useable mem2
The top portion of MEM2 (the second 64MB memory block) in the Nintendo
Wii video game console is used by the firmware running on the Starlet
processor.

Add code to calculate the portion of MEM2 safely useable by the
Broadway processor. When running under the 'mini' firmware this is
easily determined from an in-memory header. Otherwise, a safe default
is used.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-12 22:24:31 -07:00
Albert Herranz
6cdd24179d powerpc: wii: bootwrapper bits
Add support for the Nintendo Wii video game console to the powerpc
bootwrapper.

dtbImage.wii is a wrapped image that contains a flat device tree,
an entry point compatible with the Homebrew Channel and BootMii,
and an optional initrd.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-12 22:24:29 -07:00
Albert Herranz
7a09116c01 powerpc: wii: device tree
Add a device tree source file for the Nintendo Wii video game console.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-12 22:24:29 -07:00
Albert Herranz
b68a24bc78 powerpc: gamecube: bootwrapper bits
Add support for the Nintendo GameCube video game console to the powerpc
bootwrapper.

dtbImage.gamecube is a wrapped image that contains a flat device tree,
an entry point compatible with SDload, and an optional initrd.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-12 22:24:26 -07:00
Albert Herranz
86ad53f8aa powerpc: gamecube: device tree
Add a device tree source file for the Nintendo GameCube video game console.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-12 22:24:26 -07:00
Albert Herranz
26054c9541 powerpc: gamecube/wii: usbgecko bootwrapper console support
Add support for using the USB Gecko adapter as a bootwrapper console on
the Nintendo GameCube and Wii video game consoles.
The USB Gecko is a 3rd party memory card interface adapter that provides
a EXI (External Interface) to USB serial converter.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-12-12 22:24:26 -07:00
Sean MacLennan
a18cb387e5 powerpc/44x: Increase warp SD buffer
Newer revs of the FPGA have a larger SD buffer.

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-12-11 09:52:26 -05:00
Anatolij Gustschin
070bae1fb0 powerpc/44x: Extend Katmai dts for ADMA and RAID56 support
Add nodes for PPC440SPe DMA, I2O, XOR engines and Memory
Queue module which are used in the updated PPC440SPe ADMA
driver. Also extend plb ranges property to specify address
ranges for DMA0/1 and I2O engines.

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-12-11 09:51:42 -05:00
Anton Vorontsov
1cad2c8741 powerpc/83xx: Add power management support for MPC8315E-RDB boards
- Add nodes for PMC and GTM controllers. GTM4 can be used as a wakeup
  source;

- Add fsl,magic-packet properties to eTSEC nodes, i.e. wake-on-lan
  support. Unlike MPC8313 processors, MPC8315 can resume from deep
  sleep upon magic packet reception.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-12-10 19:56:50 -06:00
Dmitry Eremin-Solenikov
b387dfe902 powerpc/83xx: mpc8349emitx - add leds-gpio binding
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-12-09 15:15:54 -06:00