Add infrastructure for supporting per-cpu local timers to update
the profiling information and update system time accounting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ia64 translates normal loads and stores to special MMIO regions into I/O port
accesses. Reserve these special MMIO regions in /proc/iomem.
Sample /proc/iomem:
f8100000000-f81003fffff : PCI Bus 0000:80 I/O Ports 00000000-00000fff
f8100400000-f81007fffff : PCI Bus 0000:8e I/O Ports 00001000-00001fff
f8100800000-f8100ffffff : PCI Bus 0000:9c I/O Ports 00002000-00003fff
f8101000000-f81017fffff : PCI Bus 0000:aa I/O Ports 00004000-00005fff
and corresponding /proc/ioports:
00000000-00000fff : PCI Bus 0000:80
00001000-00001fff : PCI Bus 0000:8e
00002000-00003fff : PCI Bus 0000:9c
00004000-00005fff : PCI Bus 0000:aa
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When a page has a memory uncorrectable ECC error, the recovery
code wants to prevent the page from being reused. This change
bumps the reference count to prevent the page from getting back
on the free list.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
paddr needs to be shifted by PAGE_SHIFT to be valid
input for pfn_valid().
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The determination of whether an MCA is recoverable or not must
be based on the bits set in the PSP (Processor State Parameter).
The specific bits are shown in the Intel IA-64 Architecture Software
Developer's Manual, Vol 2, Table 11-6 Software Recovery Bits in
Processor State Parameter. Those bits should be consistent
across the entire IA-64 family of processors.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update comment on get_user_insn to the more general "pte lock", which may
or may not be the page_table_lock. Note vmtruncate handled like kswapd.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, attempting to invoke a signal-handler on the normal
stack is guaranteed to fail if the stack-pointer happens not to be
16-byte aligned. This is because the signal-trampoline will attempt
to store fp-regs with stf.spill instructions, which will trap for
misaligned addresses. This isn't terribly useful behavior. It's
better to just always align the signal frame to the next lower 16-byte
boundary.
Signed-off-by: David Mosberger-Tang <David.Mosberger@acm.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The original memory less node allocation attempted to use NODEDATA_ALIGN for
alignment. The bootmem allocator only allows a power of two alignments. This
causes a BUG_ON for some nodes. For cpu only nodes just allocate with a
PERCPU_PAGE_SIZE alignment.
Some older firmware reports SLIT distances of 0xff and results in bestnode
not being computed. This is now treated correctly.
The failed allocation check was removed because it's redundant. The
bootmem allocator already makes this check.
This fix has been boot tested on 4 node machine which has 4 cpu only nodes
and 1 memory node. Thanks to Pete Keilty for reporting this and helping me
test it.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/arm/kernel/irq.c:998:26: warning: Using plain integer as NULL pointer
arch/arm/kernel/smp.c:145:25: warning: Using plain integer as NULL pointer
arch/arm/kernel/smp.c:362:5: warning: symbol 'smp_call_function_on_cpu' was not declared. Should it be static?
drivers/video/amba-clcd.c:521:12: warning: symbol 'amba_clcdfb_init' was not declared. Should it be static?
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This factors out the common bits of arch/powerpc/xmon/start_*.c into
a new nonstdio.c, and removes some stuff that was supposed to make
xmon's I/O routines somewhat stdio-like but was never used.
It also makes the parsing of the xmon= command line option common,
so that ppc32 can now use xmon={off,on,early} also.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some powermac machines were crashing in the quiesce firmware call
in prom_init.c because we have just closed the OF stdin device;
notably my 1999 G3 powerbook does this. To avoid this, don't
close the OF stdin device on powermacs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Until we have local timer support, we need to broadcast the
timer interrupt to the other CPUs. Also, add the missing
smp_send_timer() prototype to asm/smp.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ppc64 needs a special sysfs probe file for adding new memory.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
memmap_init_zone() sets page count to 1. Before 'freeing' the
page, we need to clear the count. This is the same that is done
on free_all_bootmem_core() for memory discovered at boot time.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the create_section_mapping() routine to create hptes for memory
sections dynamically added after system boot.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For some stupid reason I can't explain (brown paper bag is at hand), I
removed the check pfn_valid() in the code that does the icache/dcache
coherency on POWER4 and later. That causes us to eventually try to
access non existing struct page when hashing in IO pages.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, Nov 08, 2005 at 08:12:56AM +1100, Benjamin Herrenschmidt wrote:
> Yes, the MAX_ORDER should be different indeed. But can Kconfig do that ?
> That is have the default value be different based on a Kconfig option ?
> I don't see that ... We may have to do things differently here...
This seems to be done in other parts of the Kconfig file. Using those
as an example, this should keep the MAX_ORDER block size at 16MB.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Even though we can enable and disable xmon at runtime now, there are a
few places in the merge tree that call xmon and xmon_printf directly.
In the case below we call die() which will call xmon if it is enabled.
Also remove an unnecessary include of xmon.h in smp.c.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Oprofile was hardwiring the MMCRA sample bit to 1 but on newer cpus
(eg POWER5) we want to vary it based on the group being sampled.
Add a temporary workaround until people update their oprofile userspace.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64 we end up with a negative value for the data size in the memory
boot message:
Memory: 2035560k/2097152k available (5792k kernel code, 89564k reserved,
18014398509481632k data, 870k bss, 352k init)
It turns out the section ordering of the linker script is different on
ppc32 and ppc64, so just count data as _edata - _sdata which should work
on both.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xmon() prototype is inconsistent between ARCH=ppc and ARCH=powerpc,
thus causing ARCH=ppc build breakage.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Building a PowerMac kernel with ARCH=powerpc causes a bunch of warnings,
this fixes some of them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some more U3 revisions have the missing "interrupts" property in U3,
this adds them to the fixup code in prom_init.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates g5_defconfig for ARCH=powerpc in order to add the SMU
support & thermal drivers to it, the pmac sound driver (works on some
G5s) and replaces rivafb with nvidiafb which works better for the cards
found in G5 based machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the ability to the SMU driver to recover missing
calibration partitions from the SMU chip itself. It also adds some
dynamic mecanism to /proc/device-tree so that new properties are visible
to userland.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
CPU freq support using 970FX powertune facility for iMac G5 and SMU
based single CPU desktop.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
OK, the Fedora ppc32 and ppc64 kernels should both be arch/powerpc by
tomorrow. They're booting on G5, POWER5, and my powerbook. I'll test
pmac SMP and Pegasos later -- but pmac smp is known broken in arch/ppc
anyway, and I'll live with a potential Pegasos regression for now; it
wasn't supported officially in FC4 either.
I needed to fix ppc32 initrd -- we were never setting initrd_start.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
drivers/drm/ now implements proper ->compat_ioctl methods, so this isn't
needed anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
all ioctls are 32bit compat clean, so the driver can use ->compat_ioctl
and ->unlocked_ioctl easily.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
implement a compat_ioctl handle in the driver instead of having table
entries in sparc64 ioctl32.c (I plan to get rid of the arch ioctl32.c
file eventually)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
all the ioctls in the driver are 32bit compat clean and don't need BKL,
so we can switch it to ->unlocked_ioctl and ->compat_ioctl trivially.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Would you mind applying the following patch that kills those two + the
m68k and Documentation/ references?
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
all these are handled by fs/compat_ioctls.c already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't know if we ever implemented this, but the only user in any 2.6
tree are the compat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old keyboard driver is gone in 2.6, so the only user left are the
compat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old sound drivers are gone in 2.6, so the only user left are the
compat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
this inline routine in arch/sparc64/kernel/ioctl32.c is completely
unused and superceeded by compat_alloc_user_space()
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It only serves to generate false-positive buildcheck warnings.
Just set it initially to tick_operations which uses the v9
%tick register which every sparc64 processor has.
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't needed any longer, as noted by Hugh Dickins.
We still need the flush routines, due to the one remaining
call site in hugetlb_prefault_arch_hook(). That can be
eliminated at some later point, however.
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc64 is unique among architectures in taking the page_table_lock in
its context switch (well, cris does too, but erroneously, and it's not
yet SMP anyway).
This seems to be a private affair between switch_mm and activate_mm,
using page_table_lock as a per-mm lock, without any relation to its uses
elsewhere. That's fine, but comment it as such; and unlock sooner in
switch_mm, more like in activate_mm (preemption is disabled here).
There is a block of "if (0)"ed code in smp_flush_tlb_pending which would
have liked to rely on the page_table_lock, in switch_mm and elsewhere;
but its comment explains how dup_mmap's flush_tlb_mm defeated it. And
though that could have been changed at any time over the past few years,
now the chance vanishes as we push the page_table_lock downwards, and
perhaps split it per page table page. Just delete that block of code.
Which leaves the mysterious spin_unlock_wait(&oldmm->page_table_lock)
in kernel/fork.c copy_mm. Textual analysis (supported by Nick Piggin)
suggests that the comment was written by DaveM, and that it relates to
the defeated approach in the sparc64 smp_flush_tlb_pending. Just delete
this block too.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc64 prom_callback and new_setup_frame32 each operates on a user page
table without holding lock, and no doubt they've good reason. But I'd
feel more confident if they were to do a "pte = *ptep" and then operate
on pte, rather than re-evaluating *ptep.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a forward port of a 2.4.x sun4m LED driver written by Lars
Kotthoff.
Signed-off-by: Lars Kotthoff <metalhead@metalhead.ws>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Lennert Buytenhek
Since we have to use XCB=101 instead of XCB=000 on the ixp2400 to
prevent it from regularly falling over, and since we have to deal with
manual write buffer flushing because of that, we might as well use
XCB=101 on all ixp2000 platforms since it's faster than XCB=000.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
nwfpe extended precision emulation used to be broken on big-endian
and was therefore disabled. This patch fixes nwfpe so that it copies
extended precision floats to/from userspace in the proper word order
(similar to patch #2046, see the description of that patch for an
explanation) and reenables the Kconfig option.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The routine that nwfpe uses for converting floats/doubles to
extended precision fails to zero two bytes of kernel stack. This
is not immediately obvious, as the floatx80 structure has 16 bits
of implicit padding (by design.) These two bytes are copied to
userspace when an stfe is emulated, causing a possible info leak.
Make the padding explicit and zero it out in the relevant places.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
notify_die() added for MCA_{MONARCH,SLAVE,RENDEZVOUS}_{ENTER,PROCESS,LEAVE} and
INIT_{MONARCH,SLAVE}_{ENTER,PROCESS,LEAVE}. We need multiple
notification points for these events because they can take many seconds
to run which has nasty effects on the behaviour of the rest of the
system.
DIE_SS replaced by a generic DIE_FAULT which checks the vector number,
to allow interception of faults other than SS.
DIE_MACHINE_{HALT,RESTART} added to allow last minute close down
processing, especially when the halt/restart routines are called from
error handlers.
DIE_OOPS added.
The check for kprobe's break numbers has been moved from traps.c to
kprobes.c, allowing DIE_BREAK to be used for any additional break
numbers, i.e. it is no longer kprobes specific.
Hooks for kernel debuggers and kernel dumpers added, ENTER and LEAVE.
Both of these disable the system for long periods which impact on
watchdogs and heartbeat systems in general. More patches to come that
use these events to reset watchdogs and heartbeats.
unregister_die_notifier() added and both routines exported. Requested
by Dean Nelson.
Lock removed from {un,}register_die_notifier. notifier_chain_register()
already takes a lock. Also the generic notifier chain locking is being
reworked to distinguish between callbacks that can block and those that
cannot, the lock in {un,}register_die_notifier would interfere with
that change. http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
Leading white space removed from arch/ia64/kernel/kprobes.c.
Typo in mca.c in original version of this patch found & fixed by Dean
Nelson.
Signed-off-by: Keith Owens <kaos@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Acked-by: Anil Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since 2.6.13-rc1 setup_frame and its variants return int. But some bits
were missed in the conversion.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Many RTC routines were not protected against each other, so there are
potential races, for example, ntp-update against /dev/rtc. This patch
fixes them using rtc_lock.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Switch to dynamic major
o Remove duplicate SHN_MIPS_SCOMMON definition
o Coding style: remove typedefs.
o Coding style: reorder to avoid the need for forward declarations
o Use kzalloc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move some of the m68knommu platform specific irq core support
to its own header, irqnode.h. Having it in asm-m68knommu/irq.h
causes some build pain, since it is included in a number of
common code places (and not all the required definitions will
be included at these places).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added support for the new Freescale 5208 ColdFire processor.
Also changed name "Motorola" to new company name "Freescale".
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Align the param section. It can end up starting on an unalingned
boundary depending on the size of ksymtab_strings. If it is
unaligned things like modules will fail to load with unaligned
access traps.
Add linker scipt support for the M5208EVB board.
Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Freescale M5208EVB ColdFire eval board is one of the few that
doesn't have its DRAM based at address 0. Handle this special case
in the common ColdFire startup code.
Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modified common ColdFire PIT timer code to support the 5208 as well.
It uses a different set of mask and interrupt bits than other ColdFire
processors. The defines for these bits have been moved in header
files and set appropriately for the different processor varients.
Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Platform configuration code for the Freescale 5208 ColdFire processor.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add build support for the new Freescale 5208 ColdFire processor,
and its M5208EVB eval board. Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Freescale 5208 ColdFire uses the common PIT timer code for
its internal timer. Build it when configured for the 5208 processor.
Add support for the internal register map of the 5208 ColdFire fmaily.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add Freescale 5208 ColdFire platform Makefile.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add setup support for the new Freescale 5208 ColdFire processor.
(Also fixed a little typo in there, "UNKOWN" -> "UNKNOWN").
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EXPORT_SYMBOL's for phys_proc_id and cpu_core_id were added this year but
never used.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the arch/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in arch/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time conversion functions instead of hard-coded HZ division to avoid
rounding errors.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates the RIO messaging interface to pass a device instance into the
event registeration and callbacks.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds PPC32 RIO support. Init code for the MPC85xx RIO ports and glue for the
STx GP3 board to use it.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reorganize the preempt_disable/enable calls to eliminate the extra preempt
depth. Changes based on Paul McKenney's review suggestions for the kprobes
RCU changeset.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the arch kprobes infrastructure to take advantage of the locking
changes introduced by usage of RCU for synchronization. All handlers are now
run without any locks held, so they have to be re-entrant or provide their own
synchronization.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using a arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sparc64 changes to track kprobe execution on a per-cpu basis. We now track
the kprobe state machine independently on each cpu using an arch specific
kprobe control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PPC64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using an arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IA64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using an arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I386 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu, using an arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following set of patches are aimed at improving kprobes scalability. We
currently serialize kprobe registration, unregistration and handler execution
using a single spinlock - kprobe_lock.
With these changes, kprobe handlers can run without any locks held. It also
allows for simultaneous kprobe handler executions on different processors as
we now track kprobe execution on a per processor basis. It is now necessary
that the handlers be re-entrant since handlers can run concurrently on
multiple processors.
All changes have been tested on i386, ia64, ppc64 and x86_64, while sparc64
has been compile tested only.
The patches can be viewed as 3 logical chunks:
patch 1: Reorder preempt_(dis/en)able calls
patches 2-7: Introduce per_cpu data areas to track kprobe execution
patches 8-9: Use RCU to synchronize kprobe (un)registration and handler
execution.
Thanks to Maneesh Soni, James Keniston and Anil Keshavamurthy for their
review and suggestions. Thanks again to Anil, Hien Nguyen and Kevin Stafford
for testing the patches.
This patch:
Reorder preempt_disable/enable() calls in arch kprobes files in preparation to
introduce locking changes. No functional changes introduced by this patch.
Signed-off-by: Ananth N Mavinakayahanalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The sys_ptrace boilerplate code (everything outside the big switch
statement for the arch-specific requests) is shared by most architectures.
This patch moves it to kernel/ptrace.c and leaves the arch-specific code as
arch_ptrace.
Some architectures have a too different ptrace so we have to exclude them.
They continue to keep their implementations. For sh64 I had to add a
sh64_ptrace wrapper because it does some initialization on the first call.
For um I removed an ifdefed SUBARCH_PTRACE_SPECIAL block, but
SUBARCH_PTRACE_SPECIAL isn't defined anywhere in the tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-By: David Howells <dhowells@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton suggested to move kprobes from kernel hacking menu, since
kernel hacking menu is in-appropriate for the Kprobes. This patch moves
Kprobes and Oprofile under instrumentation menu.
(akpm: it's not a natural fit, but things like djprobes and the s390 guys'
statistics library need a home)
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merge common parts of head.S and head64.S into head.S and move architecture
specific parts to head31.S and head64.S respectively. Saves us ~500 lines
of duplicated assembly code.
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove pagex pseudo page fault code. It does not work together with the
system call speedup that makes the complete system call path enabled for
interrupts. To make pagex and the syscall speedup code work together we would
have to add code to the program check handler to do a critical section cleanup
like the asynchronous interrupt code. This would make program checks slower.
Not what we want.
Newer versions of z/VM have the improved pfault pseudo page fault interface.
This replaces the old pagex interface and does not have the problem. So its
better to just rip out the pagex code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't switch back to 24 bit addressing mode when waiting for an external
interrupt and set the correct bit in wait PSW (external mask instead of I/O
mask).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The calculation of the value return by next_timer_interrupt from jiffies to
jiffies_64 is racy against xtime updates. We need to protect the calculation
with read_seqbegin/read_seqretry.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Always create all signal frames for pending signals before returning to
userspace, not just a single one.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch reverts back the changes to HOSTCFLAGS and HOSTLDFLAGS
When we were building complete binaries to get constants (such as ptrace
register layout on stack) from host userspace headers, we needed to make the
arch for building HOST binaries match our one: i.e. on a 64bit system
compiling 32bit binaries, we compile 32-bit hostprogs and need, say, 32-bit
ncurses. Now we can revert that - that avoids problem with, say, menuconfig
and ncurses, on a system which can't compile well 32-bit programs.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove usage of hardcoded constants in paging_init().
By chance I spotted a bug in zones_setup involving a change to ZONE_*
constants, due to the ZONE_DMA32 patch from Andi Kleen (which is in -mm).
So, possibly, instead of zones_size[2] you will find zones_size[3] in the
code, but that change is wrong and this patch is still correct.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes some of the tt-specific options actually depend on CONFIG_MODE_TT.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A number of fixes to improve behavior when large physical memory sizes
are specified:
- libc files need -D_FILE_OFFSET_BITS=64 because there are unavoidable uses
of non-64 interfaces in libc
- some %d need to be %u
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch imlements full LDT handling in SKAS:
* UML holds it's own LDT table, used to deliver data on
modify_ldt(READ)
* UML disables the default_ldt, inherited from the host (SKAS3)
or resets LDT entries, set by host's clib and inherited in
SKAS0
* A new global variable skas_needs_stub is inserted, that
can be used to decide, whether stub-pages must be supported
or not.
* Uses the syscall-stub to replace missing PTRACE_LDT (therefore,
write_ldt_entry needs to be modified)
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The serial UML OS-abstraction layer patch (um/kernel dir).
This moves all systemcalls from helper.c file under os-Linux dir
Signed-off-by: Gennady Sharapov <Gennady.V.Sharapov@intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The serial UML OS-abstraction layer patch (um/kernel dir).
This moves all systemcalls from main.c file under os-Linux dir and joins mem.c
and um_arch.c files.
Signed-off-by: Gennady Sharapov <Gennady.V.Sharapov@intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The serial UML OS-abstraction layer patch (um/kernel dir).
This moves all systemcalls from uaccess_user.c file under os-Linux dir
Signed-off-by: Gennady Sharapov <Gennady.V.Sharapov@intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ifa->ifa_address and ifa->ifa_mask are defined as __u32, but used as if they
were char[4].
Network code uses htons() to convert it. So UML's method to access these
fields is wrong for bigendians (e.g. s390)
I replaced bytewise copying by memcpy(), maybe even that might be removed, if
ifa->ifa_address/mask may be used immediately.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike noted that the assembly code for syscall stubs is misassembled with
GCC 3.2.3: the values copied in registers weren't preserved between one asm()
and the following one.
So I fixed the thing by rewriting the __asm__ constraints more like unistd.h
ones.
Note: in syscall6 case I had to add one more instruction (i.e. moving arg6 in
eax and shuffling things around) - it's needed for the function to be valid in
general (we can't load the value from the stack, relative to ebp, because we
change it), but could be avoided since we actually use a constant as param 6.
The only fix would be to turn stub_syscall6 to a macro and use a "i"
constraint for arg6 (i.e., specify it's a constant value).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some more debugging information when a stub does something unexpected,
usually segfaulting. Now, it dumps out the stub's registers as well as the
signal.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
"extern inline" doesn't make much sense.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's widely seen a MCE non-fatal error reported after resume. It seems MCE
resume is lacked under ia32. This patch tries to fix the gap.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every file should #include the header files containing the prototypes of
its global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every file should #include the header files containing the prototypes of
its global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every file should #include the header files containing the prototypes of
its global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Excerpt from bugzilla entry
http://bugzilla.kernel.org/show_bug.cgi?id=5518
"i386 version of Reboot-through-BIOS is unsafe: it forgets to mask APIC LVT
interrupts before jumping to a BIOS entry point. As a result, BIOS ends up
bombarded with interrupts early on boot. The BIOS does not expect it since
following a "normal" hardware cpu reset, all APIC LVT registers have the
Mask bit (16) set and can't generate interrupts.
For example, the version of Phoenix BIOS used by VMware enables interrupts
for the first time before masking/clearing APIC LVT. The APIC Timer LVT
register is still set up for a timer interrupt delivery with a high vector
from the previous Linux incarnation (0xef in our case). The BIOS has not
fully initialized its IDT at this point and the real mode gate for 0xef
remains all zeros. Vector 0xef dispatches BIOS to address 0:0, BIOS takes
a #GP and eventually hangs.
machine_shutdown() does attempt to shut down APIC before jumping to BIOS,
but it is ineffective"
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SH7705 in extended cache mode has some left-over VALID_PAGE() cruft that it
checks when doing lazy dcache write-back. This has been gone for some time
(the last bits were in the discontig code, which should now also be gone --
this also fixes up a build error in the non-discontig case).
pfn_valid() gives the desired behaviour, so we switch to that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was only one board using this (hp690 specifically), and it just so
happens that it's only physically discontiguous at the "normal" P1 offset. If
we bump up the P1 offset, it's possible to hit a shadowed region of memory
where we suddenly become magically contiguous.
As people have been using this shadowed region workaround for quite some time
(and without any adverse effects), it's time to drop the left over discontig
bits that no longer have any practical use (it was always very much
hp690-centric to begin with).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds support for the relatively quirky (ie, not in line with any known
documentation, and amazed it works at all) SuperHyway implementation on
SH4-202. This depends on the earlier SuperHyway patch for multiple block
support and VCR refactoring.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sh had its own support for embedding ramdisk images in to the kernel binary,
but people are using initramfs for this now, so we drop the ramdisk embedding.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kconfig patch needed by fs_enet to work. Works like CONFIG_CPM2.
Cc: Kumar <kumar.gala@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This missing initrd header slipped though last time.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On PPC405GP/GPR it should be possible to enable PCI support, even when the
internal PCI arbiter is disabled (e.g. when using an external PCI
arbiter). The removed code didn't allow this, and also generated a warning
on PPC405EP platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup PPC40x eval boards (bubinga, walnut and sycamore) to support U-Boot
as bootloader. The OpenBIOS bd_info struct is not used in the kernel
anymore (only U-Boot now).
uImage (U-Boot) tested on walnut, sycamore and bubinga
zImage (OpenBIOS) tested on sycamore, bubinga and ebony
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the AMCC PowerPC 440SPe SoC, including PCI Express in root
port mode.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SP SoC has two Processor Local Bus (PLB) segments (a
high-throughput segment and a low-latency segment). Fix our PLB register
definitions to cope with this, and add code to dump the status of both
segments when a machine check occurs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SPe supports up to 16 GB of RAM, and therefore its IO registers
are at 0x4_xxxx_xxxx instead of being at 0x1_xxxx_xxxx like most other PPC 440
chips. To allow for this, this patch moves the definition of the ERPN used
for mapping UART0 from being hard-coded in the head_44x.S assembly code to
being defined in ibm44x.h.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds watchdog, RTC support for Marvell EV64360BP board.
Signed-off-by: Lee Nicks <allinux@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oops, some last minute changes caused the 64K pages patch to break ppc32
build, this fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The zImage wrapper has a bug where it doesn't claim() the memory for the
kernel properly, it forgets to take into account the offset between the ELF
header and the kernel itself. This results on some machines, like G5s,
into a kernel that crashes at boot when clearing the BSS.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two CONFIG_SMP=n build fixes due to missing <asm/smp.h> includes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current ia64 implementation of dma_get_cache_alignment does not work
for modules because it relies on a symbol which is not exported. Direct
access to a global is a little ugly anyway, so this patch re-implements
dma_get_cache_alignment in a manner similar to what is currently used for
x86_64.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch, however, should be applied on top of the 64k-page-size patch to
fix some problems with hugepage (some pre-existing, another introduced by
this patch).
The patch fixes a bug in the SLB miss handler for hugepages on ppc64
introduced by the dynamic hugepage patch (commit id
c594adad56) due to a misunderstanding of the
srd instruction's behaviour (mea culpa). The problem arises when a 64-bit
process maps some hugepages in the low 4GB of the address space (unusual).
In this case, as well as the 256M segment in question being marked for
hugepages, other segments at 32G intervals will be incorrectly marked for
hugepages.
In the process, this patch tweaks the semantics of the hugepage bitmaps to
be more sensible. Previously, an address below 4G was marked for hugepages
if the appropriate segment bit in the "low areas" bitmask was set *or* if
the low bit in the "high areas" bitmap was set (which would mark all
addresses below 1TB for hugepage). With this patch, any given address is
governed by a single bitmap. Addresses below 4GB are marked for hugepage
if and only if their bit is set in the "low areas" bitmap (256M
granularity). Addresses between 4GB and 1TB are marked for hugepage iff
the low bit in the "high areas" bitmap is set. Higher addresses are marked
for hugepage iff their bit in the "high areas" bitmap is set (1TB
granularity).
To avoid conflicts, this patch must be applied on top of BenH's pending
patch for 64k base page size [0]. As such, this patch also addresses a
hugepage problem introduced by that patch. That patch allows hugepages of
1MB in size on hardware which supports it, however, that won't work when
using 4k pages (4 level pagetable), because in that case hugepage PTEs are
stored at the PMD level, and each PMD entry maps 2MB. This patch simply
disallows hugepages in that case (we can do something cleverer to re-enable
them some other day).
Built, booted, and a handful of hugepage related tests passed on POWER5
LPAR (both ARCH=powerpc and ARCH=ppc64).
[0] http://gate.crashing.org/~benh/ppc64-64k-pages.diff
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to set the shared memory attribute in the page tables
on SMP systems to allow the cache coherency to operate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define ppc_md.set_dabr for both 32 + 64 bit. Cleanup the implementation for
pSeries also, it was needlessly complex. Now we just do two firmware tests at
setup time, and use one of two functions, rather than using one function and
testing on every call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mostly this involves adding #include <asm/smp.h>, since that defines
things like boot_cpuid[_phys] and [gs]et_hard_smp_processor_id, which
are SMP-related but still needed on UP. This incorporates fixes
posted by Olof Johansson and Heikki Lindholm.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ancient ppcdebug/PPCDBG mechanism is now only used in two places.
First, in the hash setup code, one of the bits allows the size of the
hash table to be reduced by a factor of 8 - which would be better
accomplished with a command line option for that purpose. The other
was a bunch of bus walking related messages in the iSeries code, which
would seem to be insufficient reason to keep the mechanism.
This patch removes the last traces of this mechanism.
Built and booted on iSeries and pSeries POWER5 LPAR (ARCH=powerpc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add nicer printing of faulting address on unresolvable kernel faults.
Makes life a little easier for those who don't know how to decode our
register contents at oops time.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds exception table entries for I/O instructions on and
changes MachineCheckException() slightly to cover 8xx specifics (on
8xx the MCE can be generated while executing the IO access instruction
itself, which is not the case on PowerMac's, as the comment on traps.c
details).
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch against m8xx_wdt.c adds <asm/io.h> (required for
out,in_be32/16) and fixes syntatic problems introduced with the IO
accessor macro update.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
setup_irq() aborts immediately if there's no handler for the IRQ in
question. So i8259_init() should set up its handlers before trying to
set up the cascade on IRQ 2.
With this and the patch I sent a few days ago to fix initrd on ppc32, my
Pegasos now runs the arch/powerpc kernel.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch contains the arch/ppc64 bits for enabling DLPAR and PCI
Hotplug for the new OF-based PCI probe mechanism. This code path is
currently broken.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel
base page size to 64K. The resulting kernel still boots on any
hardware. On current machines with 4K pages support only, the kernel
will maintain 16 "subpages" for each 64K page transparently.
Note that while real 64K capable HW has been tested, the current patch
will not enable it yet as such hardware is not released yet, and I'm
still verifying with the firmware architects the proper to get the
information from the newer hypervisors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
glibc expects to count lines beginning with "processor" to determine
the number of processors, not lines beginning with "Processor". So,
give glibc the format it expects.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't want to call dump_cpu_info() from cpu_init() after boot since
it produces a lot of unnecessary noise - since cpu_init() gets called
on resume and hotplug cpu insertion events.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Update the PXA pm.c file to allow machines (such as the Sharp
Zaurus) to override the standard pm functions but reuse/wrap them
where needed.
The init call is made slightly earlier to give machine code an init
level to override them in removing any race.
Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Since we know the value of cpsr on entry, we can replace the bic+orr with
a single eor. Also remove a possible result delay (at least on XScale).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Make the uengine loader use ixp2000_reg_wrb in the right places.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch fixes AHB/PCI endianness problems when the
processor is in little-endian mode.
The patch configures the CSR register closely following the directives
in [1], paragraph 4.1, page 19.
According to the considerations in [1], page 11, while the AHB bus
supports both endian modes, on the IXP4XX it always uses big-endian.
The PCI bus is connected to the South AHB. A wrong setting in the CSR
register will thus cause a malfunctional PCI bus.
A schematic diagram of the bus interconnections on the IXP4XX
can be found in [1], page 18.
The patch has been verified to work on the NSLU2 in
both LE and BE modes.
The author is Peter Korsgaard.
[1] Intel IXP4XX Product Line of Network Processors and IXC1100
Control Plane Processor:
Understanding Big Endian and Little Endian Modes
http://www.intel.com/design/network/applnots/25423701.pdf
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch adds basic machine support for the Sharp SL-6000x (Tosa) PDAs.
Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
my patch "x86: initialise tss->io_bitmap_owner to something" (commit ID
d5cd4aadd3) introduced a problem with a
program (DOSEMU) that called ioperm after already doing some port i/o.
The problem is that a process switch return causes tss->io_bitmap_base
to be set to IO_BITMAP_OFFSET so that the fault (that *really* sets the
io bitmap) never triggers.
This fixes that regression.
Signed-off-by: Bart Oldeman <bartoldeman@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can't currently use asm-ppc/page.h in vmlinux.lds.S, so until
we have a merged page.h, define PAGE_SIZE and KERNELBASE locally.
Also gets rid of some dynamic executable cruft that we had for
32-bit. With -Ttext=$(KERNELBASE) this didn't cause any problem,
but when we changed to putting . = KERNELBASE in the vmlinux.lds.S
this cruft caused the text to get linked at 0xa0 instead of
0xc0000000. Oops.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also moves setup_cpu_maps to setup-common.c (calling it
smp_setup_cpu_maps) and uses it on both 32-bit and 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Nicolas Pitre
We have an optimized sha1 routine (arch/arm/lib/sha1.S) meant to
override the generic one in lib/sha1.c.
Unfortunately lib/lib.a is listed _before_ arch/arm/lib/lib.a in the
link argument list and therefore the architecture specific lib functions
are not picked up before the generic versions.
This patch is a quick fix to change that ordering for ARM. Here's what
the kbuild maintainer had to say about it (was also CC'd on lkml):
On Wed, 2 Nov 2005, Sam Ravnborg wrote:
> This looks like an obvious way to achive correct ordering.
> We could change it so arch defines always took precedence but
> the above is so simple that it is not worth the effort.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add platform devices for flash to Lubbock and Mainstone board files.
Once in place, the two existing mtd map drivers for the boards will be
converted to use a single pxa2xx map driver in the linux-mtd tree.
Take 4: flash_platform_data .map_name vs. .name cleaned up, resync with
merged irda patch context.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dave Jiang
This provides support for IXP2xxx error interrupt handling. Previously there was a patch to remove this (although the original stuff was broken). Well, now the error bits are needed again. These are used extensively by the micro-engine drivers according to Deepak and also we will need it for the new EDAC code that Alan Cox is trying to push into the main kernel.
Re-submit of 3072/1, generated against git tree pulled today. AFAICT, this git tree pulled in all the ARM changes that's in arm.diff. Please let me know if there are additional changes. Thx!
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
ARM processors that have pld instructions are not using those copy_user
implementation anymore. Let's remove the useless PLD lines which were
half wrong anyway.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no reason for smp_release_cpus() to be asm, and most people can make
more sense of C code. Add an extern declaration to smp.h and remove the custom
one in machine_kexec.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Restrict CONFIG_SGI_SN_XP to IA64_GENERIC or IA64_SGI_SN2 kernels.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
wrap_mmu_context(), delayed_tlb_flush(), get_mmu_context() all
have an extra { } block which cause one extra indentation.
get_mmu_context() is particularly bad with 5 indentations to
the most inner "if". It finally gets on my nerve that I can't
keep the code within 80 columns. Remove the extra { } block
and while I'm at it, reformat all the comments to 80-column
friendly. No functional change at all with this patch.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
IXDP2401 config file has wrong baudrate and both boards have 3 UARTs.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Using a llx format to print addresses that might possibly be (only) 36
bits wide make sense. However making it a zero padded 16 char wide
field is a bit excessive and useless.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 'K' extension adds several new instructions to the ARMv6 ISA
which are primerily useful for SMP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
register_vpa() doesn't actually do a VPA register call it just uses the flags
you pass it, so rename it to vpa_call() to be clearer.
We can then define register_vpa() and unregister_vpa() which are both simple
wrappers around vpa_call(). (we'll need unregister_vpa() for kexec soon)
We can then cleanup vpa_init(), and because vpa_init() is only called from
platforms/pseries we remove the definition in asm-ppc64/smp.h.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
This adds missing header and thus fix the warning issued by ming prototype.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current comment on top of m8xx_cpm_dpinit is wrong.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently there is no Kconfig symbol to indicate that we want nvram
support on 64-bit kernels; it's assumed we always want it, so make
the powermac setup code always initialize the pmac nvram code if
64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The latest updates to bug.h generate build warnings in traps.c in
arch/ppc. Fix print format specifiers to account for change of line type
to long from int.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The extraction of PCI stuff from struct device_node left some false
assumptions in notifier code. As a result, dynamic add crashes when
non-PCI nodes are added. This patch fixes these assumptions.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we set the kernel entry point and the address of the text
section in the Makefile, using CONFIG_KERNEL_START.
But we've already got <asm/page.h> in the linker script, so we can just
use KERNELBASE directly. That means if we ever change KERNELBASE there's
one less place to change it.
And we can set the entry point with ENTRY().
There are zero differences from "readelf -a vmlinux" with or without this
patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
There's some debugging in prom.c that wraps nastly on 80 character
terminals, reformat it to fit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Merge include/asm-ppc/kexec.h and include/asm-ppc64/kexec.h.
The only thing that's really changed is that we now allocate crash_notes
properly on PPC32. It's address is exported via sysfs, so it's not correct
for it to be a pointer.
I've also removed some of the "we don't use this" comments, because they're
wrong (or perhaps were referring only to arch code).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Move plpar_wrappers.h into arch/powerpc/platforms/pseries, fixup white space,
and update callers.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Move pSeries specific code in set_dabr() into a ppc_md function, this will
allow us to keep plpar_wrappers.h private to platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Copy default configs into arch/powerpc/configs, rename bpa_defconfig to
cell_defconfig while we're at it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
This fixes the x86-64 find_[first|next]_zero_bit() function for the
end-of-range case. It didn't test for a zero size, and the "rep scas"
would do entirely the wrong thing.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
