sd->input_queue_head is incremented for each processed packet
in process_backlog(), and read from other cpus performing
Out Of Order avoidance in get_rps_cpu()
Moving this field in a separate cache line keeps it mostly
hot for the cpu in process_backlog(), as other cpus will
only read it.
In a stress test, process_backlog() was consuming 6.80 % of cpu cycles,
and the patch reduced the cost to 0.65 %
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for W5500 chip.
W5500 has similar register and memory organization with W5100 and W5200.
There are a few important differences listed below but it is still
possible to share common code with W5100 and W5200.
* W5500 register and memory are organized by multiple blocks. Each one
is selected by 16bits offset address and 5bits block select bits.
But the existing register access operations take u16 address. This change
extends the addess by u32 address and put offset address to lower 16bits
and block select bits to upper 16bits.
This change also adds the offset addresses for socket register and TX/RX
memory blocks to the driver private data structure in order to reduce
conditional switches for each chip.
* W5500 has the different register offset for socket interrupt mask
register. Newly added internal functions w5100_enable_intr() and
w5100_disable_intr() take care of the diffrence.
* W5500 has the different register offset for retry time-value register.
But this register is only used to verify that the reset value is correctly
read at initialization. So move the verification to w5100_hw_reset()
which already does different things for different chips.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add necessary Linux Ethernet driver support for promiscuous mode
operation. Add a flag so the VF knows it is in promiscuous mode
and two state flags to discreetly track multicast and unicast
promiscuous states.
Change-Id: Ib2f2dc7a7582304fec90fc917ebb7ded21ba1de4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NFV use cases require the ability to steer packets to VSIs by VLAN tag
alone while being in promiscuous mode for multicast and unicast MAC
addresses. These two new functions support that ability.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was offloading the VLAN tag into the skb
any time there was a VLAN tag and the hardware stripping was
enabled. Just check to make sure it's enabled before put_tag.
Change-Id: Ife95290c06edd9a616393b38679923938b382241
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A mirror rule ID may be zero so do not return invalid parameter when the
user passes in a zero value for a rule ID.
Change-ID: I261b8c24725ce2c6ed32f859da81093dfcbe2970
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add device capability which defines if update is available and security
check is needed during update process.
Change-ID: I380787c878275e1df18b39198df3ee3666342282
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Minor overlapping changes in the conflicts.
In the macsec case, the change of the default ID macro
name overlapped with the 64-bit netlink attribute alignment
fixes in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to 3bfd847203 ("net: Use passed in table for nexthop lookups")
for IPv4, if the route spec contains a table id use that to lookup the
next hop first and fall back to a full lookup if it fails (per the fix
4c9bcd1179 ("net: Fix nexthop lookups")).
Example:
root@kenny:~# ip -6 ro ls table red
local 2100:1::1 dev lo proto none metric 0 pref medium
2100:1::/120 dev eth1 proto kernel metric 256 pref medium
local 2100:2::1 dev lo proto none metric 0 pref medium
2100:2::/120 dev eth2 proto kernel metric 256 pref medium
local fe80::e0:f9ff:fe09:3cac dev lo proto none metric 0 pref medium
local fe80::e0:f9ff:fe1c:b974 dev lo proto none metric 0 pref medium
fe80::/64 dev eth1 proto kernel metric 256 pref medium
fe80::/64 dev eth2 proto kernel metric 256 pref medium
ff00::/8 dev red metric 256 pref medium
ff00::/8 dev eth1 metric 256 pref medium
ff00::/8 dev eth2 metric 256 pref medium
unreachable default dev lo metric 240 error -113 pref medium
root@kenny:~# ip -6 ro add table red 2100:3::/64 via 2100:1::64
RTNETLINK answers: No route to host
Route add fails even though 2100:1::64 is a reachable next hop:
root@kenny:~# ping6 -I red 2100:1::64
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::64(2100:1::64) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::64: icmp_seq=1 ttl=64 time=1.33 ms
With this patch:
root@kenny:~# ip -6 ro add table red 2100:3::/64 via 2100:1::64
root@kenny:~# ip -6 ro ls table red
local 2100:1::1 dev lo proto none metric 0 pref medium
2100:1::/120 dev eth1 proto kernel metric 256 pref medium
local 2100:2::1 dev lo proto none metric 0 pref medium
2100:2::/120 dev eth2 proto kernel metric 256 pref medium
2100:3::/64 via 2100:1::64 dev eth1 metric 1024 pref medium
local fe80::e0:f9ff:fe09:3cac dev lo proto none metric 0 pref medium
local fe80::e0:f9ff:fe1c:b974 dev lo proto none metric 0 pref medium
fe80::/64 dev eth1 proto kernel metric 256 pref medium
fe80::/64 dev eth2 proto kernel metric 256 pref medium
ff00::/8 dev red metric 256 pref medium
ff00::/8 dev eth1 metric 256 pref medium
ff00::/8 dev eth2 metric 256 pref medium
unreachable default dev lo metric 240 error -113 pref medium
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type TASKSTATS_TYPE_NULL should always be ignored.
When jumping to the next attribute, only the length of the current
attribute should be added, not the length of all nested attributes.
This last bug was not visible before commit 80df554275, because the
kernel didn't put more than two nested attributes.
Fixes: a3baf649ca ("[PATCH] per-task-delay-accounting: documentation")
Fixes: 80df554275 ("taskstats: use the libnl API to align nlattr on 64-bit")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Handle v4/v6 mixed sockets properly in soreuseport, from Craig
Gallak.
2) Bug fixes for the new macsec facility (missing kmalloc NULL checks,
missing locking around netdev list traversal, etc.) from Sabrina
Dubroca.
3) Fix handling of host routes on ifdown in ipv6, from David Ahern.
4) Fix double-fdput in bpf verifier. From Jann Horn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (31 commits)
bpf: fix double-fdput in replace_map_fd_with_map_ptr()
net: ipv6: Delete host routes on an ifdown
Revert "ipv6: Revert optional address flusing on ifdown."
net/mlx4_en: fix spurious timestamping callbacks
net: dummy: remove note about being Y by default
cxgbi: fix uninitialized flowi6
ipv6: Revert optional address flusing on ifdown.
ipv4/fib: don't warn when primary address is missing if in_dev is dead
net/mlx5: Add pci shutdown callback
net/mlx5_core: Remove static from local variable
net/mlx5e: Use vport MTU rather than physical port MTU
net/mlx5e: Fix minimum MTU
net/mlx5e: Device's mtu field is u16 and not int
net/mlx5_core: Add ConnectX-5 to list of supported devices
net/mlx5e: Fix MLX5E_100BASE_T define
net/mlx5_core: Fix soft lockup in steering error flow
qlcnic: Update version to 5.3.64
net: stmmac: socfpga: Remove re-registration of reset controller
macsec: fix netlink attribute validation
macsec: add missing macsec prefix in uapi
...
recent regressions. Changes are across several platforms, so
I'm listing every change separately here.
Regressions since 4.5:
- A correction of the psci firmware DT binding, to prevent
users from relying on unintended semantics
- Actually getting the newly merged clock driver for some OMAP
platforms to work
- A revert of patches for the Qualcomm BAM, these need to be
reworked for 4.7 to avoid breaking boards other than the one
they were intended for
- A correction for the I2C device nodes on the Socionext Uniphier
platform
- i.MX SDHCI was broken for non-DT platforms due to a change
with the setting of the DMA mask
- A revert of a patch that accidentally added a nonexisting
clock on the Rensas "Porter" board
- A couple of OMAP fixes that are all related to suspend after
the power domain changes for dra7
- On Mediatek, revert part of the power domain initialization
changes that broke mt8173-evb
Fixes for older bugs:
- Workaround for an "external abort" in the omap34xx
suspend/resume code.
- The USB1/eSATA should not be listed as an excon device on
am57xx-beagle-x15 (broken since v4.0)
- A v4.5 regression in the TI AM33xx and AM43XX DT specifying
incorrect DMA request lines for the GPMC
- The jiffies calibration on Renesas platforms was incorrect
for some modern CPU cores.
- A hardware errata woraround for clockdomains on TI DRA7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YgL2
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are the latest bug fixes for ARM SoCs, mostly addressing recent
regressions. Changes are across several platforms, so I'm listing
every change separately here.
Regressions since 4.5:
- A correction of the psci firmware DT binding, to prevent users from
relying on unintended semantics
- Actually getting the newly merged clock driver for some OMAP
platforms to work
- A revert of patches for the Qualcomm BAM, these need to be reworked
for 4.7 to avoid breaking boards other than the one they were
intended for
- A correction for the I2C device nodes on the Socionext Uniphier
platform
- i.MX SDHCI was broken for non-DT platforms due to a change with the
setting of the DMA mask
- A revert of a patch that accidentally added a nonexisting clock on
the Rensas "Porter" board
- A couple of OMAP fixes that are all related to suspend after the
power domain changes for dra7
- On Mediatek, revert part of the power domain initialization changes
that broke mt8173-evb
Fixes for older bugs:
- Workaround for an "external abort" in the omap34xx suspend/resume
code.
- The USB1/eSATA should not be listed as an excon device on
am57xx-beagle-x15 (broken since v4.0)
- A v4.5 regression in the TI AM33xx and AM43XX DT specifying
incorrect DMA request lines for the GPMC
- The jiffies calibration on Renesas platforms was incorrect for some
modern CPU cores.
- A hardware errata woraround for clockdomains on TI DRA7"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
drivers: firmware: psci: unify enable-method binding on ARM {64,32}-bit systems
arm64: dts: uniphier: fix I2C nodes of PH1-LD20
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
Revert "ARM: OMAP: Catch callers of revision information prior to it being populated"
ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
ARM: dts: am57xx-beagle-x15: remove extcon_usb1
ARM: dts: am437x: Fix GPMC dma properties
ARM: dts: am33xx: Fix GPMC dma properties
Revert "soc: mediatek: SCPSYS: Fix double enabling of regulators"
ARM: mach-imx: sdhci-esdhc-imx: initialize DMA mask
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
ARM: OMAP: Catch callers of revision information prior to it being populated
ARM: dts: dra7: Correct clock tree for sys_32k_ck
ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap
ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen
Revert "dts: msm8974: Add dma channels for blsp2_i2c1 node"
Revert "dts: msm8974: Add blsp2_bam dma node"
ARM: dts: Add clocks for dm814x ADPLL
This is more prep-work for the upcoming pty changes. Still just code
cleanup with no actual semantic changes.
This removes a bunch pointless complexity by just having the slave pty
side remember the dentry associated with the devpts slave rather than
the inode. That allows us to remove all the "look up the dentry" code
for when we want to remove it again.
Together with moving the tty pointer from "inode->i_private" to
"dentry->d_fsdata" and getting rid of pointless inode locking, this
removes about 30 lines of code. Not only is the end result smaller,
it's simpler and easier to understand.
The old code, for example, depended on the d_find_alias() to not just
find the dentry, but also to check that it is still hashed, which in
turn validated the tty pointer in the inode.
That is a _very_ roundabout way to say "invalidate the cached tty
pointer when the dentry is removed".
The new code just does
dentry->d_fsdata = NULL;
in devpts_pty_kill() instead, invalidating the tty pointer rather more
directly and obviously. Don't do something complex and subtle when the
obvious straightforward approach will do.
The rest of the patch (ie apart from code deletion and the above tty
pointer clearing) is just switching the calling convention to pass the
dentry or file pointer around instead of the inode.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When bpf(BPF_PROG_LOAD, ...) was invoked with a BPF program whose bytecode
references a non-map file descriptor as a map file descriptor, the error
handling code called fdput() twice instead of once (in __bpf_map_get() and
in replace_map_fd_with_map_ptr()). If the file descriptor table of the
current task is shared, this causes f_count to be decremented too much,
allowing the struct file to be freed while it is still in use
(use-after-free). This can be exploited to gain root privileges by an
unprivileged user.
This bug was introduced in
commit 0246e64d9a ("bpf: handle pseudo BPF_LD_IMM64 insn"), but is only
exploitable since
commit 1be7f75d16 ("bpf: enable non-root eBPF programs") because
previously, CAP_SYS_ADMIN was required to reach the vulnerable code.
(posted publicly according to request by maintainer)
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should have converted 'if (trylock)' to 'lock'.
Fixes: a6086a8937 ("drivers: net: remove NETDEV_TX_LOCKED")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov says:
====================
sh_eth: couple of software reset bit cleanups
Here's a set of 2 patches against DaveM's 'net-next.git' repo. We clean up
the use of the software reset bits...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Renesas RZ/A1H manual names the software reset bit in the software reset
register (ARSTR) ARST which makes a bit more sense than the ARSTR_ARSTR name
used now by the driver -- rename the latter to ARSTR_ARST.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_check_reset() uses a bare number where EDMR_SRST_GETHER would fit,
i.e. the receive/trasmit software reset bits that comprise EDMR_SRST_GETHER
read as 1 while the corresponding reset is in progress and thus, when both
are 0, the reset is complete.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox 100G extending mlx5 ethtool support
Changes from V0:
- Dropped: net/mlx5e: Disable link up on INIT HCA command
Due to Ido's and Or's requests we will submit this patch to net and will need it for -stable.
- Rebased to: 11afbff861 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next")
This series is centralized around extending and improving mlx5 ethernet driver ethtool
support. We've done some code refactoring for ethtool statistics reporting, making it
more scalable and robust, now each reported ethtool counter belongs to a group and has
its own descriptor within that group, the descriptor holds the counter name and offset
in memory in that group memory block.
Added new counters:
- Reporting more error and drop counter in ifconig/ip tool.
- Per priority pause and traffic counter in ethtool.
- link down events counter in ethtool.
Set features handling was also refactored a little bit to be more resilient and generic,
now setting more than one feature will not stop on the first failed one, but instead
it will try to continue setting others. We made it generic to make it simpler for adding
more features support, it is now done easily by only introducing a handler function of
the new supported netdev feature, and let the generic handler do the job.
New netdev features and ethtool support:
- Netdev feature RXALL, set on/off FCS check offload.
- Netdev feature HW_VLAN_CTAG_RX, set on/off rx-vlan stripping offload.
- Ethtool interface identify.
- Ethtool dump module EEPROM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now as rx-vlan offload can be disabled, packets can be received
with vlan tag not stripped, which means is_first_ethertype_ip will
return false, for that we need to check if the hardware reported
csum OK so we will report CHECKSUM_UNNECESSARY for those packets.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ethtool -K <interface> rxvlan <on/off> to enable/disable
C-TAG vlan stripping by hardware.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add query MCIA, PMLP registers infrastructure and commands.
Add ethtool support for get_module_info() and get_module_eeprom()
callbacks.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the needed hardware command and mlx5_ifc structs for managing LED
control.
Add set_phys_id ethtool callback to support ethtool -p flag.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new access register named Ports Check Mask Register (PCMR) to
control all HW checks on port. With this register, the driver can
enable/disable Hardware FCS validation.
When RXALL is enabled/disabled using ndo_set_features, enable/disable
fcs check at HW.
User can change HW configuration using rx-all flag at ethtool.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current mlx5e ndo_set_features implementation, setting some features
can success while others can fail. Today, we return one error code which
doesn't reflect the current features status of the netdev at the end of
the ndo callback.
Set netdev->features with features which were successfully set in order
to keep the current status in case of failure. For this purpose, define
new Macro to set/unset specific feature in netdev->features.
This patch introduces a mechanism that uses feature handlers for each
feature.
Set features will call a generic handler, which will then call a specific
handler in his turn and update netdev->features according to it's return
value. Each specific handler is responsible to perform driver specific
actions, and updating params if needed.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose link_down_events counter through ethtool -S.
This counter is read from PPort statistics, then proccessed and stored as
a special handling software counter.
This counter is stored along software counters since it is the only PPort
counter that it's size is not 64 bits.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose counters providing information for each priority level (PCP) through
ethtool -S option and DCBNL.
This includes rx/tx bytes, frames, and pause counters.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VPort and software counters names are confusing and may be unclear, all
VPort counters now have a prefix of rx/tx_vport_*.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redesign ethtool statistics handling and reporting in the driver:
1. Move counters to a separate file (en_stats.h).
2. Remove unnecessary dependencies between stats and strings.
3. Use counter descriptors which hold a name and offset for each counter,
and will be used to decide which counters will be exposed.
For example when adding a new software counter to ethtool, instead of:
1. Add to stats struct.
2. Add to strings struct in the same order.
3. Change macro defining number of software counters.
The only thing needed is to link the new counter to a counter descriptor.
VPort counters are a set of hardware traffic counters created automatically
for each virtual port opened.
PPort counters are a set of counters describing per physical port
performance statistics.
These counters are gathered from hardware register and divided to groups
according to different protocols.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide rtnl_link_stats64 with information regarding physical errors to be
seen in ifconfig and ip tool.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
net: core: remove TX_LOCKED support
Not that many users left, lets kill it.
TX_LOCKED was meant to be used by LLTX drivers when spin_trylock()
failed. Stack then re-queued if collisions happened on different
cpus or free'd the skb to prevent deadlocks.
Most of the driver removal patches fall into one of three categories:
1. remove the driver-private tx lock (and LLTX flag), or...
2. convert spin_trylock to plain spin_lock, or...
3. convert TX_LOCKED to free+TX_OK
Patches are grouped by these categories, last patch is the actual removal.
All driver changes were compile tested only with exception of atl1e.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No more users in the tree, remove NETDEV_TX_LOCKED support.
Adds another hole in softnet_stats struct, but better than keeping
the unused collision counter around.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace the trylock by a full spin_lock and remove TX_LOCKED return value.
Followup patch will remove TX_LOCKED from the kernel.
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These drivers already call netif_stop_queue() so we should not be called
unless tx space is available. Just free the skb and return TX_OK.
Followup patch will remove NETDEV_TX_LOCKED from the kernel.
Cc: linux-parisc@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
similar to atl1c: lock is only used in ndo_start_xmit, but we also
advertised LLTX, so remove that as well and let core stack handle
tx locking.
Allows to remove the TX_LOCKED return value from the driver.
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAICS this is safe: the lock is only used in the .ndo_start_xmit
function and this driver does not set LLTX.
Gets rid of TX_LOCKED return value, followup patches will remove it.
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_start_xmit never returns it to stack, but nes_nic_send helper used it if
skb could not be queued to hardware. Switch to bool instead.
Cc: <linux-rdma@vger.kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov says:
====================
Don't return NULL from get_phy_device() anymore
Here's the set of 5 patches against DaveM's 'net-next.git' repo. The first
patch makes get_phy_device() return only error values on error, the rest of
the patches clean up the callers of that function...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann asked that get_phy_device() returns either NULL or the error
value, not both on error. Do as he said, return ERR_PTR(-ENODEV) instead
of NULL when the PHY ID registers read as all ones.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_dev_init() is now always called with 'true' as the 2nd argument,
so that there's no more sense in having 2 parameters to this function...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For sctp assoc, when rcvbuf_policy is set, it will has it's own
rmem_alloc, when we dump asoc info in sctp_diag, we should use that
value on RMEM_ALLOC as well, just like WMEM_ALLOC.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvtap_device_event(NETDEV_UNREGISTER) should check vlan->minor to
determine if it is being invoked in the context of a macvtap_newlink
that failed, for example in this code sequence:
macvtap_newlink
macvlan_common_newlink
register_netdevice
call_netdevice_notifiers(NETDEV_REGISTER, dev)
macvtap_device_event(NETDEV_REGISTER)
<fail here, vlan->minor = 0>
rollback_registered(dev);
rollback_registered_many
call_netdevice_notifiers(NETDEV_UNREGISTER, dev);
macvtap_device_event(NETDEV_UNREGISTER)
<nothing to clean up here>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If macvlan_common_newlink fails in register_netdevice after macvlan_init
then it decrements port->count twice, first in macvlan_uninit (from
register_netdevice or rollback_registered) and then again in
macvlan_common_newlink.
A similar problem may exist in the ipvlan driver.
This patch consolidates modifications to port->count into macvlan_init
and macvlan_uninit (thanks to Eric Biederman for suggesting this approach).
v3: remove macvtap specific bits.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>