Commit Graph

291 Commits

Author SHA1 Message Date
Russell King
be50972935 [ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07 09:40:08 +01:00
Shadi Ammouri
60cadec9da spi: new orion_spi driver
This adds an SPI driver for the SPI controller found in various Marvell
Orion ARM SoCs.  It currently supports only one slave, which must use SPI
mode 0.

[dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"]
Signed-off-by: Shadi Ammouri <shadi@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-05 14:33:46 -07:00
Gerard Kam
dc329442b9 atmel_spi: fix hang due to missed interrupt
For some time my at91sam9260 board with JFFS2 on serial flash (m25p80)
would hang when accessing the serial flash and SPI bus.  Slowing the SPI
clock down to 9 MHz reduced the occurrence of the hang from "always"
during boot to a nuisance level that allowed other SW development to
continue.  Finally had to address this issue when an application stresses
the I/O to always cause a hang.

Hang seems to be caused by a missed SPI interrupt, so that the task ends
up waiting forever after calling spi_sync().  The fix has 2 parts.  First
is to halt the DMA engine before the "current" PDC registers are loaded.
This ensures that the "next" registers are loaded before the DMA operation
takes off.  The second part of the fix is a kludge that adds a
"completion" interrupt in case the ENDRX interrupt for the last segment of
the DMA chaining operation was missed.

The patch allows the SPI clock for the serial flash to be increased from 9
MHz to 15 MHz (or more?).  No hangs or SPI overruns were encountered.

Haavard: while this patch does indeed improve things, I still see overruns
and CRC errors on my NGW100 board when running the DataFlash at 10 MHz.
However, I think some improvement is better than nothing, so I'm passing
this on for inclusion in 2.6.27.

Signed-off-by: Gerard Kam <gerardk5@verizon.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-04 16:58:45 -07:00
Ben Dooks
5aa6cf302c spi: S3C24XX: reset register status on resume.
Fix a bug in the spi_s3c24xx driver where it does not reset the registers
of the hardware when resuming from suspend (this block has been reset over
suspend).

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-04 16:58:45 -07:00
Ben Dooks
cb1d0a7a5d spi_s3c24xx: really assign busnum
The original "Pass the bus number we expect the S3C24XX SPI driver to
attach to via the platform data." [1] patch was mis-sent, and missed two
important parts of the diff, which was to actually set the bus_num field
and add the relevant field to the platform data.

The previous commit 50f426b55d promised to
add a bus_num field, but failed to include the two hunks that added this
field to include/asm-arm/arch-s3c2410/spi.h and then pass it to the spi
core when creating the new master field in drivers/spi/spi_s3c24xx.c.

[1] git commit 50f426b55d

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-28 16:30:21 -07:00
Luotao Fu
9a7867e1b3 mpc52xx_psc_spi: fix block transfer
The block transfer routine in the mpc52xx psc spi driver misinterpret
the datasheet.  According to the processor datasheet the chipselect is
held as long as the EOF is not written.

Theoretically blocks of any sizes can be transferred in this way.  The
old routine however writes an EOF after every word, which has the size
of size_of_word.  This makes the transfer slow.

Also fixed some duplicate code.

Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-28 16:30:21 -07:00
Benjamin Herrenschmidt
d65d830ca0 Merge commit 'gcl/gcl-next' 2008-07-28 16:30:40 +10:00
FUJITA Tomonori
8d8bb39b9e dma-mapping: add the device argument to dma_mapping_error()
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:

This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).

I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread).  So I
CC'ed this to KVM camp.  Comments are appreciated.

A pointer to dma_mapping_ops to struct dev_archdata is added.  If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it.  If it's
NULL, the system-wide dma_ops pointer is used as before.

If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging).  It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.

The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations.  So x86 can't have dma_mapping_ops per
device.  Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.

The first patch adds the device argument to dma_mapping_error.  The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.

This patch:

dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations.  So we can't have dma_mapping_ops per device.

Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function.  x86 IOMMUs use device
argument.

[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-26 12:00:03 -07:00
Grant Likely
dc87c98e8f spi: split up spi_new_device() to allow two stage registration.
spi_new_device() allocates and registers an spi device all in one swoop.
If the driver needs to add extra data to the spi_device before it is
registered, then this causes problems.  This is needed for OF device
tree support so that the SPI device tree helper can add a pointer to
the device node after the device is allocated, but before the device
is registered.  OF aware SPI devices can then retrieve data out of the
device node to populate a platform data structure.

This patch splits the allocation and registration portions of code out
of spi_new_device() and creates two new functions; spi_alloc_device()
and spi_register_device().  spi_new_device() is modified to use the new
functions for allocation and registration.  None of the existing users
of spi_new_device() should be affected by this change.

Drivers using the new API can forego the use of spi_board_info
structure to describe the device layout and populate data into the
spi_device structure directly.

This change is in preparation for adding an OF device tree parser to
generate spi_devices based on data in the device tree.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
2008-07-25 22:34:29 -04:00
Jan Nikitenko
bbe48ecc7f spi: au1550_spi: improve pio transfer mode
Improve PIO transfer mode of au1550 spi controller by continuing of spi
transfer, instead of aborting transfer when transmit underflow interrupt
occurrs.

Verified by oscilloscope that the spi clock pauses on trasmit underflow,
so transfer continuation is perfectly valid even though au1550 datasheet
says that on tx underflow zeroes will be transfered.

Also make some error messages more specific.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Manuel Lauss
3a93a159c6 spi: au1550_spi: proper platform device
Remove the Au1550 resource table and instead extract MMIO/IRQ/DMA
resources from platform resource information like any well-behaved
platform driver.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Alan Cox
4ef754b7d7 spidev: BKL removal
Another step to removing ->ioctl and to removing the BKL

[dbrownell@users.sourceforge.net: take final step; BKL not needed]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Grant Likely
102eb97564 spi: make spi_board_info.modalias a char array
Currently, 'modalias' in the spi_device structure is a 'const char *'.
The spi_new_device() function fills in the modalias value from a passed in
spi_board_info data block.  Since it is a pointer copy, the new spi_device
remains dependent on the spi_board_info structure after the new spi_device
is registered (no other fields in spi_device directly depend on the
spi_board_info structure; all of the other data is copied).

This causes a problem when dynamically propulating the list of attached
SPI devices.  For example, in arch/powerpc, the list of SPI devices can be
populated from data in the device tree.  With the current code, the device
tree adapter must kmalloc() a new spi_board_info structure for each new
SPI device it finds in the device tree, and there is no simple mechanism
in place for keeping track of these allocations.

This patch changes modalias from a 'const char *' to a fixed char array.
By copying the modalias string instead of referencing it, the dependency
on the spi_board_info structure is eliminated and an outside caller does
not need to maintain a separate spi_board_info allocation for each device.

If searched through the code to the best of my ability for any references
to modalias which may be affected by this change and haven't found
anything.  It has been tested with the lite5200b platform in arch/powerpc.

[dbrownell@users.sourceforge.net: cope with linux-next changes: KOBJ_NAME_LEN obliterated, etc]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Robert P. J. Day
6291fe2abc SPI Kconfig simplifications
Use "if SPI_MASTER" to remove numerous dependencies.

[dbrownell@users.sourceforge.net: remove a couple now-needless EXPERIMENTAL dependencies too]
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Roel Kluin
166a375b65 xilinx_spi: test below 0 on unsigned irq in xilinx_spi_probe()
xilinx_spi->irq is unsigned, so the test fails

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrei Konovalov <akonovalov@ru.mvista.com>
Cc: Yuri Frolov <yfrolov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Chen Gong
a61f5345eb spi: spi_mpc83xx clockrate fixes
This updates the SPI clock rate calculations for the spi_mpc83xx driver.
Some boundary conditions were wrong, and in several cases divide-by-16
wasn't always needed

Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Greg Kroah-Hartman
695794ae0c Driver Core: add ability for class_find_device to start in middle of list
This mirrors the functionality that driver_find_device has as well.

We add a start variable, and all callers of the function are fixed up at
the same time.

The block layer will be using this new functionality in a follow-on
patch.


Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-07-21 21:54:47 -07:00
David Brownell
3d81252ddb device create: spi: convert device_create to device_create_drvdata
Switch over to use the shiny new device_create_drvdata() call
instead of the original device_create() calls, so this continues
to work after device_create() is  removed.

Note that this driver never had the race which motivated removing
the original call; it locked correctly.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-07-21 21:54:45 -07:00
Benjamin Herrenschmidt
43d2548bb2 Merge commit '85082fd7cbe3173198aac0eb5e85ab1edcc6352c' into test-build
Manual fixup of:

	arch/powerpc/Kconfig
2008-07-15 15:44:51 +10:00
Benjamin Herrenschmidt
5b0504c0d7 Merge commit 'gcl/gcl-next' 2008-07-15 11:55:27 +10:00
Linus Torvalds
85082fd7cb Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
  [ARM] 5171/1: ep93xx: fix compilation of modules using clocks
  [ARM] 5133/2: at91sam9g20 defconfig file
  [ARM] 5130/4: Support for the at91sam9g20
  [ARM] 5160/1: IOP3XX: gpio/gpiolib support
  [ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
  [ARM] 5084/1: zylonite: Register AC97 device
  [ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
  [ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
  [ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
  [ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
  [ARM] 5144/1: pxaficp_ir: cleanup includes
  [ARM] pxa: remove pxa_set_cken()
  [ARM] pxa: allow clk aliases
  [ARM] Feroceon: don't disable BPU on boot
  [ARM] Orion: LED support for HP mv2120
  [ARM] Orion: add RD88F5181L-FXO support
  [ARM] Orion: add RD88F5181L-GE support
  [ARM] Orion: add Netgear WNR854T support
  [ARM] s3c2410_defconfig: update for current build
  [ARM] Acer n30: Minor style and indentation fixes.
  ...
2008-07-14 16:06:58 -07:00
Jonathan Corbet
2fceef397f Merge commit 'v2.6.26' into bkl-removal 2008-07-14 15:29:34 -06:00
Stephen Rothwell
76ef7dd030 powerpc/mpc52xx_psc_spi: use linux/of_platform.h instead of asm
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-07-12 12:10:53 -06:00
Russell King
f0006314d3 Merge branch 'imx' into devel
Conflicts:

	arch/arm/mm/Kconfig
2008-07-10 16:41:50 +01:00
Sascha Hauer
38a41fdf94 IMX: introduce clock API
This patch introduces the clock API for i.MX and converts all
in-Kernel drivers to use it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-07-05 10:02:46 +02:00
Sebastian Siewior
4b1295b0df spi: fix the read path in spidev
This got broken by the recent "fix rmmod $spi_driver while spidev-user is
active".  I tested the rmmod & write path but didn't check the read path.
I am sorry.  The read logic changed and spidev_sync_read() +
spidev_sync_write() do not return zero on success anymore but the number
of bytes that has been transfered over the bus.  This patch changes the
logic and copy_to_user() gets called again.

The write path returns the number of bytes which are written to the
underlying device what may be less than the requested size.  This patch
makes the same change to the read path or else we request a read of 20
bytes, get 10, don't call copy to user and report to the user that we read
10 bytes.

[akpm@linux-foundation.org: remove test of known-to-be-zero local]
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04 10:40:08 -07:00
Paulius Zaleckas
f7def13ed0 [ARM] 5122/1: imx_dma_request_by_prio simpilfication
imx_dma_request_by_prio can return channel number by itself.
No need to supply variable address through parameters.

Also converted all drivers using this function.

Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-03 16:39:57 +01:00
Jonathan Corbet
609f9e92b5 spidev: BKL pushdown
Add the BKL to spidev_open(), even though the existing locking looks
adequate.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2008-06-20 14:05:50 -06:00
David Brownell
b2c8daddcb spi: fix refcount-related spidev oops-on-rmmod
This addresses other oopsing paths in "spidev" by changing how it manages
refcounting.  It decouples the lifecycle of the per-device data from the
class device (not just the spi device):

  - Use class_{create,destroy} not class_{register,unregister}.
  - Use device_{create,destroy} not device_{register,unregister}.
  - Free the per-device data only when TWO conditions are true:
      * Driver is unbound from underlying SPI device, and
      * Device is no longer open (new)

Also, spi_{get,set}_drvdata not dev_{get,set}_drvdata for simpler code.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-06 11:29:08 -07:00
David Brownell
25d5cb4b03 spi: remove some spidev oops-on-rmmod paths
Somehow the spidev code forgot to include a critical mechanism: when the
underlying device is removed (e.g.  spi_master rmmod), open file
descriptors must be prevented from issuing new I/O requests to that
device.  On penalty of the oopsing reported by Sebastian Siewior
<bigeasy@tglx.de> ...

This is a partial fix, adding handshaking between the lower level (SPI
messaging) and the file operations using the spi_dev.  (It also fixes an
issue where reads and writes didn't return the number of bytes sent or
received.)

There's still a refcounting issue to be addressed (separately).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Reported-by: Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:14 -07:00
Grant Likely
57cc097931 mpc5200_psc_spi: typo fix in header block
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-14 19:11:12 -07:00
Joakim Tjernlund
c9bfcb3151 spi_mpc83xx: much improved driver
The current driver may cause glitches on SPI CLK line since one must disable
the SPI controller before changing any HW settings.  Fix this by implementing
a local spi_transfer function that won't change speed and/or word size while
CS is active.

While doing that heavy lifting a few other issues were addressed too:
 - Make word size 16 and 32 work too.
 - Honor bits_per_word and speed_hz in spi transaction.
 - Optimize the common path.

This also stops using the "bitbang" framework (except for a few constants).

[Roel Kluin <12o3l@tiscali.nl>: "irq" needs to be signed]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-13 08:02:25 -07:00
Eric BENARD
0cf942d75a spi: pxa2xx_spi clock resume bugfix
There is a typo in pxa2xx_spi.c, comment says "Enable the SSP clock", code
says: clk_disable ...  so after resume, the SSP is dead.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ned Forrester <nforrester@whoi.edu>
Cc: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-13 08:02:23 -07:00
Matthew Wilcox
0d34aa4d5a spi_s3c24xx signedness fix
On Fri, Apr 18, 2008 at 09:08:55PM +0200, Julia Lawall wrote:
> I found 63 occurrences of this problem with the following semantic match
> (http://www.emn.fr/x-info/coccinelle/):
>
> @@ unsigned int i; @@
>
> * i < 0
>

Since this one's always in the range 0-255, it could probably be made
signed, but it's just as easy to make it work unsigned.

Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-01 08:04:01 -07:00
Vitja Makarov
8eeb12e5a2 spi_bfin5xx: use PIO for full duplex, not DMA
Use PIO for full-duplex transfers, instead of DMA.

Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-01 08:04:01 -07:00
Haavard Skinnemoen
592e7bf805 atmel_spi: clean up baud rate divisor calculation
Make the baud rate divisor calculation code a bit more readable and add a
few comments.

Also fix wrong debug information being displayed when !new_1 and
max_speed_hz == 0.

[david-b@pacbell.net: fix it]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: "Janesh Ramakrishnan" <jramakrishnan@neuropace.com>
Acked-by David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:31 -07:00
Andrea Paterniani
5d9f3f6b7c spi: spi_imx updates
Updates to the i.MX SPI controller driver:

 1) Some comments changed and/or added.

 2) End of transfers is now managed on TXFIFO empty interrupt after the
    last write to TXFIFO.  This speeds interrupt execution by removing
    the wait for TXFIFO to become empty.  On TXFIFO empty interrupt the
    handler needs only to poll for the end of the ongoing transaction
    (SPI_CONTROL_XCH) to close the transfer.
     (2.1) Write only transfers are closed flushing RXFIFO.
     (2.2) Read transfers are closed reading trailing bytes from RXFIFO.
     (2.3) Read transfers where RXFIFO overrun occurred are closed by
           flushing RXFIFO and aborting the message.

 3) Fifos are now flushed via SPI disable after the end of ongoing
    transaction.

Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:31 -07:00
Atsushi Nemoto
0671981478 atmel_spi: support zero length transfer
A spi transfer with zero length is not invalid.  For example, such
transfer (len == 0 && delay_usecs != 0) can be used to achieve delay
before first CLK edge after chipselect assertion.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:31 -07:00
Harvey Harrison
b687d2a8f8 spi: replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:31 -07:00
David Brownell
cf43369d55 spi: pxa2xx_spi "sparse" fixes
Various cleanups to pxa2xx_spi suggested by "sparse": make sure that
register addresess are "void __iomem *", and make a few functions properly
static.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ned Forrester <nforrester@whoi.edu>
Cc: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:31 -07:00
Alessandro Guido
79d8c7a8c8 spi: use menuconfig for CONFIG_SPI
Signed-off-by: Alessandro Guido <alessandro.guido@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:31 -07:00
Ben Dooks
d1e7780638 spi: spi_s3c24xx must initialize num_chipselect
The SPI core now expects num_chipselect to be set correctly as due to added
checks on the chip being selected before an transfer is allowed.  This patch
adds a num_cs field to the platform data which needs to be set correctly
before adding the SPI platform device.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-15 19:35:41 -07:00
Ben Dooks
50f426b55d spi: spi_s3c24xx must initialize bus_num
Pass the bus number we expect the S3C24XX SPI driver to attach to via the
platform data.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-15 19:35:41 -07:00
Ben Dooks
4bb5eba06b spi: spi_s3c24xx driver must init completion
The s3c24xx_spi_txrx() function should initialise the completion each time
before using it, otherwise we end up with the possibility of returning success
before the interrupt handler has processed all the data.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-15 19:35:41 -07:00
Kay Sievers
7e38c3c445 spi: fix platform driver hotplug/coldplug
Since 43cc71eed1, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable SPI
platform drivers, to allow module auto loading.

[dbrownell@users.sourceforge.net: more drivers: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-11 08:06:43 -07:00
Michael Hennerich
b9ad8985f2 spi: spi_bfin5xx: remove unused label
Remove unused label, and associated compiler warning.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-08 18:25:53 -07:00
Vitja Makarov
f9e522caec spi: spi_bfin5xx: fix probe() sequencing
Fix bug in SPI probe: first initialize peripheral pins, and just after
register spi master device.  This fixes problems with SPI drivers built-in
kernel.

Singed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-08 18:25:53 -07:00
Mike Frysinger
4fb98efacf spi: spi_bfin5xx build fix
Fix breakage cause by overzealous line wrapping; there should be only one
format string.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-08 18:25:53 -07:00
Jan Nikitenko
2cfb8ce8c8 spi_bitbang: short transfer status fix
SPI controller drivers return number of bytes actually transfered from
bitbang->txrx_bufs() method.  This updates handling of short transfers (where
the transfer size is less than requested):

 - Even zero byte short transfers should report errors;
 - Include short transfers in the total of transferred bytes;
 - Use EREMOTEIO (like USB) not EMSGSIZE to report short transfers

Short transfers don't normally mean invalid message sizes, but if the
underlying controller driver needs to use EMSGSIZE it can still do so.

[db: fix two more minor issues]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-13 13:11:43 -07:00
Jan Nikitenko
40369e1cdb au1550_spi: fix prototype of irq handler
Remove struct pt_regs *regs from prototype of au1550_spi_irq handler to avoid
warning in request_irq().  Also fix comment type leadin.

Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-13 13:11:43 -07:00
Grant Likely
4874cc1b51 powerpc: mpc5200: fix build error on mpc52xx_psc_spi device driver
Commit id 94f389485e (Separate MPC52xx PSC FIOF
regsiters from the rest of PSC) split the PSC fifo registers away from the
core PSC regs.  Doing so broke the mpc52xx_psc_spi driver.

This patch teaches the mpc52xx_psc_spi driver about the new PSC fifo
register definitions.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:12 -08:00
Ned Forrester
b97c74bddc spi: pxa2xx_spi clock polarity fix
Fixes a sequencing bug in spi driver pxa2xx_spi.c in which the chip select
for a transfer may be asserted before the clock polarity is set on the
interface.  As a result of this bug, the clock signal may have the wrong
polarity at transfer start, so it may need to make an extra half transition
before the intended clock/data signals begin.  (This probably means all
transfers are one bit out of sequence.)

This only occurs on the first transfer following a change in clock polarity
in systems using more than one more than one such polarity.  The fix
assures that the clock mode is properly set before asserting chip select.

This bug was introduced in a patch merged on 2006/12/10, kernel 2.6.20.
The patch defines an additional bit in: include/asm-arm/arch-pxa/regs-ssp.h
for 2.6.25 and newer kernels but this addition must be made in:
include/asm-arm/arch-pxa/pxa-regs.h for kernels between 2.6.20 and 2.6.24,
inclusive

Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-23 17:12:14 -08:00
Atsushi Nemoto
f6febccd7f atmel_spi: fix clock polarity
The atmel_spi driver does not initialize clock polarity correctly (except for
at91rm9200 CS0 channel) in some case.

The atmel_spi driver uses gpio-controlled chipselect.  OTOH spi clock signal
is controlled by CSRn.CPOL bit, but this register controls clock signal
correctly only in 'real transfer' duration.  At the time of cs_activate()
call, CSRn.CPOL will be initialized correctly, but the controller do not know
which channel is to be used next, so clock signal will stay at the inactive
state of last transfer.  If clock polarity of new transfer and last transfer
was differ, new transfer will start with wrong clock signal state.

For example, if you started SPI MODE 2 or 3 transfer after SPI MODE 0 or 1
transfer, the clock signal state at the assertion of chipselect will be low.
Of course this will violates SPI transfer.

This patch is short term solution for this problem.  It makes all CSRn.CPOL
match for the transfer before activating chipselect.  For longer term, the
best fix might be to let NPCS0 stay selected permanently in MR and overwrite
CSR0 with to the new slave's settings before asserting CS.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-23 17:12:14 -08:00
David Brownell
5beec4aa2a spi: remove more dev->power.power_state usage
Remove some more references to dev->power.power_state.  That field is overdue
for removal, but we can't do that while it's still referenced in the kernel.
The only reason to update it was to make the /sys/devices/.../power/state
files (now removed) work better.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
Mike Frysinger
26fdc1f0df spi_bfin: headers are not for changelogs
Use simpler comment headers, and strip out information that is maintained in
GIT history

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
Sonic Zhang
13f3e642b2 spi_bfin: wait for tx to complete on write paths
SPI writes should also not return until the last bit is sent.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
Bryan Wu
4fd432d9c7 spi_bfin: wait for tx to complete on full duplex paths
Full duplex SPI operation should not read a dummy byte at the first transfer.
Bug and fix by Jean-Christian de Rivaz <jc@eclis.ch>:

http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3678

Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
Bryan Wu
e26aa015dd spi_bfin: wait for tx to complete on some cs_chg paths
PBX 2 SPI devices need the nonstandard "cs change per word" mechanism.

This patch is one of three updating this driver to make the last data bits get
sent before advancing the transfer ...  in this case, before the chipselect
gets deactivated.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
Bryan Wu
aab0d83ee7 spi_bfin: use more useful GPIO labels
Use the SPI driver's name when requesting gpio lines.  When there are gpio
conflicts, this helps to narrow down the problems; "bfin-spi" is not
informative.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
Bryan Wu
8d20d0a7c4 spi_bfin: remove useless fault path
Remove useless return status check in restore_state function.  Issue was
pointed out by Michael.

Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
Girish
ccc7baed18 spi: omap2_mcspi handles omap3 too
This adds driver OMAP SPI specific changes to support OMAP 3430

Signed-off-by: Girish S G <girishsg@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
Magnus Damm
37e4664087 spi: SuperH SPI using SCI
Add support for SPI over SCI pins.  SCI is a very simple serial controller
block that can be found on older SuperH processors.  In theory it is
possible to use the SCI hardware block in syncronous mode, but this version
of the driver simply hooks up the bit banging code on the SCI pins.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
David Brownell
b359fbc458 spi: s3c drivers shouldn't care about spi_board_info
The two S3C SPI master drivers got merged without much review, so I just
noticed that they're doing something that the SPI core code is responsible
for, rather than any adapter driver: they try to register SPI devices.

This removes that support from those drivers so they act normally.
Interestingly, none of the current boards are affected.  So it's a net code
shrink with no loss of functionality.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:11 -08:00
Haavard Skinnemoen
8bacb21901 atmel_spi: fix dmachain oops with DEBUG enabled
In atmel_spi_next_xfer, xfer can be NULL because the next transfer may
already have been submitted to the PDC (using DMA chaining).  This can
cause an oops, since the debug message assumed it was never null.  The
fix changes how those debug messages are issued, ensuring that one is
issued each time a transfer is started instead of once per call.

Also, properly indent the "can this transfer be chained" test so it's
not hidden as if it were non-conditional code.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:10 -08:00
Silvester Erdeg
154443c72f atmel_spi: chain DMA transfers
Add support for chained transfers in the atmel_spi driver, letting the DMA
controller switch to the next buffer pair without CPU intervention.  This
reduced I/O latencies by about 2% in one bulk I/O test.  It should also help
work around several interrelated errata affecting chipselect 0 on at91rm9200
chips.

Almost all of the changes are in the reworked atmel_spi_next_xfer() function.
That's now called with the driver in one of three states:

 1. It isn't transferring anything (in which case the first transfer
    of the current message is going to be sent)
 2. It has finished transfering a non-chainable transfer (in which
    case it will go to the next transfer in the message)
 3. It has finished transfering a chained transfer (in which case the
    next transfer is already queued)

After that it will queue the next transfer if it can be chained.

Signed-off-by: Szilveszter Ordog <slipszi@gmail.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:10 -08:00
Haavard Skinnemoen
1eed29df47 atmel_spi throughput improvement
Don't insert (undesirable) delays between consecutive words (DLYBCT) or when
activating chipselects (DLYBS).

Removing the between-word delays improves the performance of bulk transfers
(such as mtd_dataflash, m25p80, mmc_spi) significantly.  In one test, the
improvement was a factor of more than eight!

(The large DLYBCT value came from the legacy at91 SPI driver, and it's not
clear why it used such a huge value.)

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:10 -08:00
David Brownell
3c72426f05 spi core: stop updating dev->power.power_state
Don't update dev->power.power_state any more in the SPI core.  The only
reason to update this scheduled-to-be-removed field was to make the
already-removed /sys/devices/.../power/state files work better.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:10 -08:00
Jeff Garzik
15aafa2f9d Remove pointless casts from void pointers
Mostly in and around irq handlers.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck Tony" <tony.luck@intel.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Karsten Keil <kkeil@suse.de>
Acked-by: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:01 -08:00
Ralf Baechle
911f21501f Remove inclusions of <linux/autoconf.h>
Nothing should ever include this file.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: "Mike Frysinger" <vapier.adi@gmail.com>
Acked-by: "Bryan Wu" <cooloney.lkml@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:00 -08:00
Paulius Zaleckas
efad798b9f Spelling fixes: lenght->length
Signed-off-by: Paulius Zaleckas <pauliusz@yahoo.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
2008-02-03 15:42:53 +02:00
Paul Mackerras
bd45ac0c5d Merge branch 'linux-2.6' 2008-01-31 11:25:51 +11:00
Paul Mackerras
4eece4ccf9 Merge branch 'for-2.6.25' of git://git.secretlab.ca/git/linux-2.6-mpc52xx 2008-01-31 10:50:17 +11:00
Anton Vorontsov
59a0ea5091 spi_mpc83xx: use brg-frequency for SPI in QE
In case of QE we can use brg-frequency (which is qeclk/2).
Thus no need to divide sysclk in the spi_mpc83xx.

This patch also adds code to use get_brgfreq() on QE chips.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-28 08:32:57 -06:00
Grant Likely
4fb4c55824 [POWERPC] mpc52xx_psc_spi device driver must not touch port_config and cdm
It is dangerous for an mpc52xx device driver to modify the port_config
register.  If the driver is probed incorrectly, it will change the pin
IO configuration in ways which may not be compatible with the board.
port_config should be set up by the bootloader, or failing that, in
the platform setup code in arch/powerpc/platforms/52xx.

Also, modifying CDM registers directly can cause a race condition with
other drivers.  Instead call a common routine to modify CDM settings.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Dragos Carp <dragos.carp@toptica.com>
2008-01-26 15:32:19 -07:00
Grant Likely
66ffbe490b [POWERPC] mpc5200: normalize compatible property bindings
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:

http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html

This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix.  The drivers will still bind against
the older names also.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-26 15:26:01 -07:00
eric miao
2f1a74e5a2 [ARM] pxa: make pxa2xx_spi driver use ssp_request()/ssp_free()
1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
   information of the designated SSP port.

2. remove those IRQ/memory request code, ssp_request() has done that for
   the driver

3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
   has to be defined, all will be retreived by ssp_request()

4. introduce ssp_get_clk_div() to handle controller difference in clock
   divisor setting

5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
   handle the different SSP clock frequency between different processors

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:52 +00:00
eric miao
0aea1fd565 [ARM] pxa: move SSP register definitions from pxa-regs.h to regs-ssp.h
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:51 +00:00
Dave Young
5ed2c832ed spi: use class iteration api
Convert to use the class iteration api.

Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-01-24 20:40:45 -08:00
Kalle Valo
feed9bab7b spi: omap2_mcspi PIO RX fix
Before transmission of the last word in PIO RX_ONLY mode rx+tx mode
is enabled:

	/* prevent last RX_ONLY read from triggering
	 * more word i/o: switch to rx+tx
	 */
	if (c == 0 && tx == NULL)
		mcspi_write_cs_reg(spi,
				OMAP2_MCSPI_CHCONF0, l);

But because c is decremented after the test, c will never be zero and
rx+tx will not be enabled. This breaks RX_ONLY mode PIO transfers.

Fix it by decrementing c in the beginning of the various I/O loops.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-24 14:06:44 -08:00
Paul Mackerras
9156ad4833 Merge branch 'linux-2.6' 2008-01-24 10:07:21 +11:00
Grant Likely
75ca399e82 [POWERPC] mpc5200: eliminate mpc52xx_*_map_*() functions.
mpc5200 platform code defines a bunch of map functions which duplicate the
functionality of of_iomap().  Remove them and use of_iomap() instead.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-18 09:30:37 -07:00
David Brownell
d52df2e2ea spi_bitbang: always grab lock with irqs blocked
Fix a glitch reported by lockdep in the spi_bitbang code: it needs to
consistently block IRQs when holding that spinlock.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-08 16:10:35 -08:00
Rini van Zetten
d84248bf46 atmel_spi: reload RCR before TCR
We have a wifi module connected to the spi bus and got sometimes FIFO
overrun errors on the spi bus.

After some investigation i found that the driver loads the TCR (transmit
count) register before the RCR (receive count).  When the transfer list is
not empty the atmel_spi_next_message is called while tx and rx are enabled.
 As soon as the TCR is loaded, hardware starts transfer and causes a rx
fifo overrun because the RCR is not loaded yet.

Load the RCR before the TCR.  After this patch the fifo overrun disapears
at out setup.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Rini van Zetten <rini@arvoo.nl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-10 19:43:55 -08:00
Will Newton
8805f23870 spi_imx: fix typo in description
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-10 19:43:55 -08:00
Will Newton
6b1a802839 spi_bfin5xx: fix typo in description
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-10 19:43:55 -08:00
Will Newton
037cdafe42 pxa2xx_spi: fix typo in description
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-10 19:43:54 -08:00
Bryan Wu
092e1fdaf3 Blackfin SPI driver: reconfigure speed_hz and bits_per_word in each spi transfer
- reconfigure SPI baud from speed_hz of each spi transfer
 - according to spi_transfer.bits_per_word to reprogram register and setup
   correct SPI operation handlers

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:20 -08:00
Bryan Wu
003d922618 Blackfin SPI driver: move hard coded pin_req to board file
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time

 - move this static things to the blackfin board file
 - add pin_req array to struct bfin5xx_spi_master
 - tested on BF537/BF548 with SPI flash

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:20 -08:00
Bryan Wu
f452126c2e Blackfin SPI driver: use void __iomem * for regs_base
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:20 -08:00
Bryan Wu
d8c05008b0 Blackfin SPI driver: use cpu_relax() to replace continue in while busywait
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:20 -08:00
Sonic Zhang
07612e5f22 spi: spi_bfin: resequence DMA start/stop
Set correct baud for spi mmc and enable SPI only after DMA is started.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:20 -08:00
Bryan Wu
62310e51ac spi: spi_bfin: update handling of delay-after-deselect
Move cs_chg_udelay handling (specific to this driver) to cs_deactive(), fixing
a bug when some SPI LCD driver needs delay after cs_deactive.

Fix bug reported by Cameron Barfield <cbarfield@cyberdata.net>
https://blackfin.uclinux.org/gf/project/uclinux-dist/forum/?action=ForumBrowse&forum_id=39&_forum_action=ForumMessageBrowse&thread_id=23630&feedback=Message%20replied.

Cc: Cameron Barfield <cbarfield@cyberdata.net>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:20 -08:00
Bryan Wu
c3061abb9e spi: spi_bfin: bugfix for 8..16 bit word sizes
Fix bug in u16_cs_chg_reader to read data_len-2 bytes data firstly, then read
out the last 2 bytes data

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:20 -08:00
Bryan Wu
bb90eb00b6 spi: spi_bfin: handle multiple spi_masters
Move global SPI regs_base and dma_ch to struct driver_data.  Test on BF54x SPI
Flash with 2 spi_master devices enabled.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:19 -08:00
Sonic Zhang
3f479a65b3 spi: spi_bfin: relocate spin/waits
Move spin/waits to more correct locations in bfin SPI driver.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:19 -08:00
Sonic Zhang
cc487e7320 spi: spi_bfin: change handling of communication parameters
Fix SPI driver to work with SPI flash ST M25P16 on bf548

Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer.  But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.

This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:19 -08:00
Sonic Zhang
12e17c4267 spi: spi_bfin, rearrange portmux calls
Move pin muxing to setup and cleanup methods.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:19 -08:00
Sonic Zhang
7c4ef09449 spi: spi_bfin uses portmux for additional busses
Use portmux mechanism to support SPI busses 1 and 2, instead of just the
original bus 0.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:19 -08:00
Bryan Wu
a32c691d7c spi: spi_bfin uses platform device resources
Update spi driver to support multi-ports by using platform resources; tested
on STAMP537+SPI_MMC, other boards need more testing.  Plus other minor
updates.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:19 -08:00
Mike Frysinger
2ed355165f spi: spi_bfin, don't bypass spi framework
Prevent people from setting bits in ctl_reg that the SPI framework already
handles, hopefully we can one day drop ctl_reg completely

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-12-05 09:21:19 -08:00