Add new module parameter that force module not to register bluetooth rfkill.
There is report that saying using this bluetooth rfkill to enable/disable
bluetooth will let bluetooth device initial failed when enable on Lenovo
ideapad S12. Fortunately there is another rfkill registered by bluetooth
driver for S12 and user can shutdown the bluetooth by either bluetooth driver
or HW RF switch.
For dual OS user, it may have some trouble that using Linux after turning off
bluetooth with another OS if we do not register bluetooth rfkill at all. So
we will force bluetooth enable when no_bt_rfkill=1.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Tested-by: Mario 'BitKoenig' Holbe <Mario.Holbe@TU-Ilmenau.DE>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Since the platform drivers doing more for laptops than just using specific
ACPI device. It will be good to change the name from *_acpi to *-laptop.
Reference: http://lkml.org/lkml/2010/8/14/154
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
1. Read hw rfkill status by ec command
2. Not to touch sw status of each rfkill when hw rfkill notify
3. Initial rfkill status when module loaded
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There are several bits of the return value of _CFG shows if RF/Camera devices
exist or not.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
By reading from method _CFG to make sure we bind on the correct VPC2004 device.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There are two methods under VPC2004 which is used to access VDAT/VCMD of EC
register. Add helpers for read and write these two registers.
And add read_method_int for reading the return value from ACPI methods which
requires no parameter.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Export the status of RF killswitch through debugfs.
The killswitch status is obtained by the SMI to BIOS. Exporting this status
through debugfs can help identify the issue with the misbehaving firmware.
Signed-off-by: Keng-Yu Lin <keng-yu.lin@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Instead of creating wmi_blocks and then register corresponding devices
on a separate pass do it all in one shot, since lifetime rules for both
objects are the same. This also takes care of leaking devices when
device_create fails for one of them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Instead of adding modalias attribute manually set it up as class's
device attribute so driver core will create and remove it for us.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Do not abuse wmi_block structure to hold the head of list
of blocks, use separate list_head for that.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There is no reason why we allocate memory and copy data into an
intermediate buffer, it is not like we are working with data coming
from userspace.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
If we _WDG returned object that is not buffer we were forgetting
to free memory allocated for that object.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Driver initialization was forgetting to remove EC address space handler
in cases when parse_wdg() method failed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Instead of registering (and removing) every attribute individually
switch to using sysfs attribute group. This makes sure that we
properly unwind and do not try to remove non-existent attributes which
may not be safe to do in the future.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
We need to include the SFI headers. This is fine as the SCU is only
relevant to x86 platforms with SFI.
Fixes the -next warning report.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In 2.6.35 the hex_to_bin() was introduced.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fix kconfig recursive dependency error in ACPI_TOSHIBA:
it uses both select and depends on for BACKLIGHT_CLASS_DEVICE.
drivers/video/backlight/Kconfig:117:error: recursive dependency detected!
drivers/video/backlight/Kconfig:117: symbol BACKLIGHT_CLASS_DEVICE is selected by ACPI_TOSHIBA
drivers/platform/x86/Kconfig:490: symbol ACPI_TOSHIBA depends on LEDS_CLASS
drivers/leds/Kconfig:12: symbol LEDS_CLASS is selected by BACKLIGHT_ADP8860
drivers/video/backlight/Kconfig:285: symbol BACKLIGHT_ADP8860 depends on BACKLIGHT_CLASS_DEVICE
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The driver uses sparse keymap library and does not use this field
anymore.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The GPS rfkill crappy code. The ops_data argument wasn't
set, and was totally misused. The fix have been tested
on an Asus R2H.
Cc: stable@kernel.org
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Makes asus-laptop and eeepc-laptop _init/_exit functions
looks exactly the same as they do the same thing.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Instead of implementing its own version of keymap hanlding switch over
to using sparse keymap library.
Also, install notify handler only after we allocated input device,
otherwise we may risk getting event too early and crash. Similarly,
notify handler should be removed before we unregister input device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Instead of implementing its own version of keymap hanlding switch over
to using sparse keymap library.
Also make sure that we install notify handler only after we allocated
input device and that we remove notify handler before unregistering
input device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Instead of implementing its own version of keymap hanlding switch over to
using sparse keymap library.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
nstead of implementing its own version of keymap hanlding switch over to
using sparse keymap library.
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Instead of implementing its own version of keymap hanlding switch over to
using sparse keymap library.
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The undocumented interface we're using for reading CPU power seems to be
overreporting power. Until we figure out how to correct it, disable CPU
turbo and power reporting to be safe. This will keep the CPU within default
limits and still allow us to increase GPU frequency as needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The BIOS may hand us a lower CPU power limit than the default for a
given SKU. We should use it in case the platform isn't designed to
dissapate the full TDP of a given part.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Both when polling the current turbo status (in poll_turbo_status mode)
and when handling thermal events (in ips_irq_handler) the current status
of GPU turbo is updated to match the hardware status. However if during
driver initialisation we were unable aquire linkage to the i915 driver
enabling GPU turbo will lead to an oops on the first attempt to determine
GPU busy status.
Ensure that we do not enable GPU turbo unless we have driver linkage.
BugLink: http://bugs.launchpad.net/bugs/632430
Cc: stable@kernel.org
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Print some interesting values when MCP limits
are exceeded.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
They're optional. If not present or sane, we should use the CPU
defaults.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
If the CPU doesn't support turbo, don't try to enable/disable it.
http://bugzilla.kernel.org/show_bug.cgi?id=18742
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The patch is to create ips_adjust thread before ips_monitor begins
to run because the latter will kthread_stop() or wake up the former
via ips->adjust pointer. Without this change, it is possible that
ips->adjust is NULL when kthread_stop() or wake_up_process() is
called in ips_monitor().
Signed-off-by: minskey guo <chaohong.guo@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In ips_get_i915_syms(), the symbol i915_gpu_busy() is not released
when error occurs.
Signed-off-by: minskey guo <chaohong.guo@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The variable old_cpu_power is used to save the value of THM_CEC
register. In get_cpu_power(), it will be divided by 65535.
Signed-off-by: minskey guo <chaohong.guo@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The mask of sequence number in THM_ITV register is 16bit width instead
of 8bit.
Signed-off-by: minskey guo <chaohong.guo@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Change the code so that it will use the correct size for keymap entries.
Do it in a way that makes it harder to screw it up in the future.
Reported-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
We should pass the data to the data register.
Signed-off-by: Jianwei Yang <jianwei.yang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It looks like there is an off-by-one error in one of your changes to
drivers/staging/rar_register/rar_register.c:
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The machines I have appear to provide their return value in the arguments
structure, not the output structure. Rework the driver to use that again
in order to get rfkill working again.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Don't ask how ACPI_TOSHIBA got enabled on in desktop system's .config -
I don't know. But it has silently been there until I tried 2.6.36-rc2,
where it broke the build because I don't have LED support turned on.
Attached patch fixes things up.
(I had to change BACKLIGHT_CLASS_DEVICE to "depends" because otherwise
I get unsightly core dumps out of scripts/kconfig/conf).
jon
--
toshiba: make sure we pull in LED support
The Toshiba extras driver uses the LED module, so make sure we have it
configure in.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
