Also remove legacy '/proc' name during OS_DEVICE_NAME
registration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Where the DPC logic would get jammed into continuously
reloging-into a port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's no need to reset the RISC prior to pausing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Newer ISPs support a mechanism to read and write flash-memory via
the firmware LOAD/DUMP memory mailbox command routines. When
supported, utilizing these mechanisms significantly reduces
overall access times.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original implementation manipulated the FC_GS values for
port-speed. Transition the codes to use the driver's own
internal representations as this makes for a reduction in
duplicate 'conversion' codes throughout the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transitioning link-state via NOS/OLS requires a relogin to a
fabric's Management Server. Request relogin when the firmware
issues a point-to-point asynchronous event (0x8030).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- this patch will fix a panic caused by omitted memory allocation for the nvram.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a patch to fix 'segmentation fault' issue which was initiated
by Richard Lary <rlary@us.ibm.com>. Thanks again Richard.
- on following sysfs attritute function, changes have made so that both
count and offset input parameters are honored by the functions.
= qla2x00_sysfs_read_nvram()
= qla2x00_sysfs_read_vpd()
- made changes so that NVRAM data to be cached to minimize H/W accesses
during agent querying of the driver's.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Left overs from last code merges of qla2xxx
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Large code-reuse from ISP24xx, consolidate RISC memory
extraction routines during firmware-dump.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As the "must-check" return-value of pci_set_msi() is never
really checked.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original from Peter Oruba <peter.oruba@amd.com>. Additional
cleanups included.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Following patch bump up the driver version reflecting NPIV addition to
the qla2xxx.
- version changed from 8.01.07-k7 to 8.02.00-k1.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following patch adds support for NPIV (N-Port ID Virtualization) to the
qla2xxx.
- supported within switched-fabric topologies only.
- supports up to 63 virtual ports on each physical port.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
Well, first of all, I don't want to change so many files either.
What I do:
Adding a new parameter "struct bin_attribute *" in the
.read/.write methods for the sysfs binary attributes.
In fact, only the four lines change in fs/sysfs/bin.c and
include/linux/sysfs.h do the real work.
But I have to update all the files that use binary attributes
to make them compatible with the new .read and .write methods.
I'm not sure if I missed any. :(
Why I do this:
For a sysfs attribute, we can get a pointer pointing to the
struct attribute in the .show/.store method,
while we can't do this for the binary attributes.
I don't know why this is different, but this does make it not
so handy to use the binary attributes as the regular ones.
So I think this patch is reasonable. :)
Who benefits from it:
The patch that exposes ACPI tables in sysfs
requires such an improvement.
All the table binary attributes share the same .read method.
Parameter "struct bin_attribute *" is used to get
the table signature and instance number which are used to
distinguish different ACPI table binary attributes.
Without this parameter, we need to offer different .read methods
for different ACPI table binary attributes.
This is impossible as there are various ACPI tables on different
platforms, and we don't know what they are until they are loaded.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iterations is unsigned, so it is impossible to get out of the loop
and return -ETIMEDOUT.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Optimize fault kprobe handling just like powerpc.
[SPARC]: Wire up utimensat syscall.
[SPARC64]: Fix request_irq() ignored result warnings in PCI controller code.
[SPARC64]: Kill asm-sparc64/pbm.h
[ATYFB]: Fix sparc includes.
[QLA2XXX]: Fix build on sparc.
[SPARC64]: Removal of trivial pci_controller_info uses.
[SPARC64]: Move index info pci_pbm_info.
[SPARC64]: Move {setup,teardown}_msi_irq into pci_pbm_info.
[SPARC64]: Move pci_ops into pci_pbm_info.
[SPARC64] SBUS: Error interrupt registry cleanups.
[SPARC64] PCI: Use root list of pbm's instead of pci_controller_info's
[SPARC64] PCI: Kill PROM_PCIRNG_MAX and PROM_PCIIMAP_MAX.
[SPARC64] PCI: Use common routine to fetch PBM properties.
We now use pci_device_to_OF_node() to get properties
and of_get_property() returns const pointers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported ISP types include ISP2422 and revision-2 type
ISP2432 chips.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hardcoding the qlport_down_retry module-parameter
effectively disallowed any user-defined NVRAM setting to go
into effect.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove a stale check against ha->device_flags
(DFLG_NO_CABLE) as topology scanning is performed within the
DPC-thread context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some sparc64 boxes don't have a valid NVRAM (from which the driver
takes its WWPN) try to extract this from open firmware instead and if
that fails, fall back to a default, which would be invalid if more
than one machine on the same SAN does this, since two machines with
the same WWPN would be illegal, so warn when taking this potentially
invalid default.
Tested on SunBlade-1000:
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On the path qla2x00_probe_one() -> probe_failed -> qla2x00_free_device(),
pci_disable_device() is executed twice, once in qla2x00_free_device()
and once in qla2x00_probe_one().
This patch removes the unnecessary call.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes byte swap issue in qla2xxx driver
to fix corrupted fabric_name passed to
/sys/class/fc_host/host*/fabric_name.
Signed-off-by: Richard Lary <rlary@us.ibm.com>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The module parameter, ql2xextended_error_logging, can now be
set dynamically by writing to the following sysfs entry:
/sys/module/qla2xxx/parameters/ql2xextended_error_logging
This alleviates the need for the driver to be unloaded and
reloaded in order to enable logging.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's no need given, I/O has been quiesced, RISC
interrupts have been disabled, and finally the RISC has been
paused. Flash manipulation on ISP21xx, ISP22xx, and ISP23xx
parts requires the RISC to go through a full reset to
recover.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We're observing soft lockups during HBA FLASH retrieval and
update. Add cond_resched() each time around the tight-loops
during flash read()s/write()s.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
qla2xxx driver fails to handle RSCN events affecting area or domain due
to an endian issue on big endian systems. This fixes the port_id_t
structure on big endian systems.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since, mailbox commands are executed in a synchronous
manner, there is no need to have a separate spinlock
primitive to protect data/register access shared by callers.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As ISP24xx firmware can return a CS_DATA_UNDERRUN completion
status when the storage has returned a
SAM_STAT_TASK_SET_FULL scsi-status.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Non-ISP24xx cards must have a loop-id in order to query host
statistics.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Limit assignments via qla2x00_model_name[] array to HBA
subsystem vendor IDs equal to QLogic.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Previous work to add asynchronous-scsi-scanning support
(d19044c32b) caused peculiar
semantic changes when no cabling was attached to the HBA
whereby unneeded and intrusive 'error-handling' would take
place due to the initial link state being unset.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similarly to previous LOGO requests on non-24xx hardware,
perform an implicit-LOGO as to avoid the potential 2 *
R_A_TOV delay which can result during an explicit-LOGO
request.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This includes BIOS, EFI, FCODE and firmware versions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
No restriction should be placed on the IRQ number assigned
to a given ISP. Original code incorrectly assumed a
non-zero IRQ number assignment by the system. In these
circumstances the proper freeing of the IRQ (via free_irq())
would not take place.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Removed spin_unlock_irq()/spin_lock_irq() pairs surrounding
starget_for_each_device() calls.
As Matthew W. pointed out, starget_for_each_device() can be called under
a spinlock being held.
The change has been tested and verified on qla2xxx.ko module.
Thanks Matthew W. and Hisashi H. for help.
Signed-off-by: Andrew Vasquez <Andrew.vasquez@qlogic.com>
Signed-off-by: Seokmann Ju <Seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rather than a direct call, as was done in the case of a
RISC-paused state within the ISP24xx interrupt handler.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code would incorrectly use non-24xx code-paths.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Disable subsequent GPSC queries if Fabric Management services do
not support the operation.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use NULL instead of 0 for pointers (sparse warning):
drivers/scsi/qla2xxx/qla_attr.c:393:4: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Modify intialization semantics:
- perform basic hardware configuration only (as usual)
- allocate resources
- load and execute firmware
- defer link (transport) negotiations to the DPC thread
- again the code in qla2x00_initialize_adapter() to stall probe()
completion was needed for legacy-style scanning.
- DPC thread stalls until probe() complete.
- before probe() completes, set DPC flags to perform loop-resync logic
(similar to what's done during cable-insertion/removal).
Benefits: user does not have to wait 20+ seconds in case the FC cable
is unplugged during driver load, code consolidation (removal of
redundant link negotiation logic during initialize_adaoter()), and
finilly, the driver no longer needs to defer the fc_remote_port_add()
calls to hold off lun-scanning prior to returning from the probe()
function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Drop queue-depths across all luns for a given fcport
during TASK_SET_FULL statuses.
- Ramp-up I/Os after throttling.
- Consolidate completion-status handling of CS_QUEUE_FULL with
CS_COMPLETE as ISP24xx firmware no longer reports
CS_QUEUE_FULL.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Early ISP2432 parts have a known hardware issue when coming
out of a D3 hot state. This issue can result in a hung PCIe
link. Recent firmwares contain a workaround whereby the
stop-firmware mailbox command prevents the ISP from entering
the D3 hot state.
In order to ensure that the workaround succeeded the driver
must verify that the stop-firmware mailbox command completes
successfully. In the event of a failure, the driver
attempts a shutdown-retry after resetting the ISP and
re-executing firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* git://git.infradead.org/~dhowells/irq-2.6:
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
IRQ: Typedef the IRQ handler function type
IRQ: Typedef the IRQ flow handler function type
commit 0181944fe6 adds a
'extended_error_logging' global variable to qla2xxx which is defined by
qla4xxx too.
Trying to build both drivers results in the following error:
LD drivers/scsi/built-in.o
drivers/scsi/qla4xxx/built-in.o: In function `qla4xxx_slave_configure':
drivers/scsi/qla4xxx/ql4_os.c:1433: multiple definition of `extended_error_logging'
drivers/scsi/qla2xxx/built-in.o:drivers/scsi/qla2xxx/qla_os.c:2166:
first defined here
make[2]: *** [drivers/scsi/built-in.o] Error 1
make[1]: *** [drivers/scsi] Error 2
make: *** [drivers] Error 2
The following patch simply adds a qla2_ (qla4_ respectively) prefix to
the variable name.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Stall error handler if attempting recovery while an rport is
blocked. This avoids device offline scenarios due to errors in
the error handler.
Reference implementation from lpfc/mptfc.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The system hostname will be used during a subsequent FDMI registration
with the fabric.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Refactored original code from qla_gs.c:qla2x00_rsnn_nn().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iIDMA (Intelligent Interleaved Direct Memory Access) allows for
the HBA hardware to send FC frames at the rate at which they can
be received by a target device. By taking advantage of the
higher link rate, the HBA can maximize bandwidth utilization in a
heterogeneous multi-speed SAN.
Within a fabric topology, port speed detection is done via a Name
Server command (GFPN_ID) followed by a Fabric Management command
(GPSC). In an FCAL/N2N topology, port speed is based on the HBA
link-rate.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Software must explicitely re-enable extended firmware tracing
after any ISP abort condition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only. If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).
The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently it is impossible to reset provided by Qlogic QLA2xxx driver
SCSI devices externally using corresponding sg devices, particularly via
sg_reset utility, because qla2xxx driver in qla2xxx_eh_device_reset()
function checks if the input scsi_cmnd has its private data (CMD_SP())
attached. Then the found pointer isn't used anywhere inside of
qla2xxx_eh_device_reset(). If the RESET request comes from sg device, it
doesn't have such private data.
The attached patch removes check for non-NULL CMD_SP() from
qla2xxx_eh_device_reset(), hence allows to reset QLA2xxx's devices using
corresponding sg devices.
AV: change applies to bus/host reset handlers as well.
Signed-off-by: Vladislav Bolkhovitin <vst@vlnb.net>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/nsp32.c
drivers/scsi/pcmcia/nsp_cs.c
Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a few spaces to MODULE_PARM_DESC() text for qla2xxx. Without these
spaces text runs together when modinfo prints the text.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/aacraid/comminit.c
Fixed up by removing the now renamed CONFIG_IOMMU option from
aacraid
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code incorrectly assigned it to the driver's
link-down-timeout value (a value in seconds).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also remove qla2xxx_probe_one/qla2xxx_remove_one stubs previously
used with external firmware module loaders.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As there is no point in failing the initialization process when
firmware informs the host software that it could not transition
beyond a CONFIG_WAIT nor WAIT_FOR_LOGIN state. Previous logic
would mark such conditions as a general *failure* and subsequently
tear-down the scsi-host during initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similar in form to QLogic's standard offering -- via
the 'extended_error_logging' module parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- macro usage statements should terminate with a ';'
- remove unused macros.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The host section of ISP24xx NVRAMs contain a new bit which
allows a user to selectively disable ports of an HBA. These
ports (hosts) will not be presented to the midlayer.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Defer firmware dump-data raw-to-textual conversion to
user-space.
- Add module parameter (ql2xallocfwdump) to allow for per-HBA
allocations of firmware dump memory.
- Dump request and response queue data as per firmware group
request.
- Add extended firmware trace support for ISP24XX/ISP54XX chips.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.
Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semantic changes in ISP24xx firmware behaviour inadvertently
caused the driver to believe an F-port topology was present in an
N_port-to-N_port configuration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify and centralise buffer allocation/deallocation, as
there's no point in having two memory request methods.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Expandind on the previous commit:
commit 79f89a4296
Author: andrew.vasquez@qlogic.com <andrew.vasquez@qlogic.com>
Date: Fri Jan 13 17:05:58 2006 -0800
[SCSI] qla2xxx: Disable port-type RSCN handling via driver state-machine.
and given:
- the process-context requirements of the FC transport
rport-APIs.
- lack of port-type RSCN processing logic for ISP24xx and newer
chips.
it's time now to remove the state-machine logic from mainline.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In qla2x00_reset_chip the driver first takes the hardware lock,
and then later on takes the mbx lock.
In the mailbox_command code.. it goes the other way around.
Discovered with the lock validator.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If firmware image is unavailable via request_firwmare(), then
attempt to load the image (likely out-of-date) stored in flash
memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With ISP24XX and ISP54XX parts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix the driver to return SUCCESS if the firmware or driver doesn't
have a command to abort, i.e., it's already been returned. Without
this patch, error recovery will take the target offline as it tries
harder and harder to get the driver to return the command it no longer
has.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qla2x00_probe_one() fails before calling request_irq() but gets to
qla2x00_free_device() then it will mistakenly try to free an irq it didn't
request. It's chosing to free based on ha->pdev->irq which is always set.
host->irq is set after request_irq() succeeds so let's use that to decide
to free or not.
This was observed and tested when a silly set of circumstances lead to
firmware loading failing on a 2100.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Modify well over a dozen mempool users to call mempool_create_slab_pool()
rather than calling mempool_create() with extra arguments, saving about 30
lines of code and increasing readability.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ISP24XX FW does not support Mbx 0x74 ie Login Local Port.
Added the equivalent code for ISP24XX ie to relogin in non
fabric case for ISP24XX use login iocb.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Only support ZIO mode 6 on specific ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Reserved-bit 15 must set when updating the swing/emphasis values.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Resync with latest NVRAM subsystem ID list.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As new 23xx firmware will accomidate ISP63xx types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Chip is similar in form to our ISP24xx offering.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use the kthread_ API instead of opencoding lots of hairy code for kernel
thread creation and teardown.
Also switch from semaphore-based thread wakeup to wake_up_process.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-By: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
4gb products require an IOCB's FCP-LUN to be formatted in
wire-format prior to submission.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recent ISP24xx firmwares require that mailbox register 8 be
set to the maximum number of bytes to transfer during DMA
copying of the list. We safely set this value to zero
(infinite), since the call is *only* made in FCAL
topologies.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Commit 854165f424
inadvertently added some code meant only for testing -- the
driver was ignoring the non-zero function numbers of a
multi-port HBA.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fcport visibility is recognized during interrupt time, but,
rport removal can only occur during a process
(sleeping)-context. Return a DID_IMM_RETRY status for
commands submitted within this window to insure I/Os do not
prematurely run-out of retries.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Internal lun discovery has been removed since fc_transport
integration. Short-circuiting for tape-devices in
qla2x00_update_fcport() could inadvertently result in a
blocked rport timing-out and its targets being reaped.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A target can LOGO an initiator at any time (i.e. during I/O,
due to a controller hicup, or as a simple authentication
mechanism after an initial CDB command), when this occurs,
the driver attempts to relogin (PLOGI) to the device via the
DPC thread. Add code to make the appropriate upcall to the
FC transport layer (fc_remote_port_add()) upon successful
completion of the PLOGI.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver can typically detect port-loss during an
interrupt context (i.e. via interrogation of a status IOCB's
completion status [CS_PORT_LOGGED_OUT]. Due to the calling
requirements of the fc_rport APIs, the driver would defer
removal of the device to the default workqueue. If the
work-item was preceded by an event which caused the port to
obtain visibility (relogin successful, target re-logged into
the topology), deferred removal could inadvertently drop the
rport. The code also no longer defers removal via the
default workqueue, instead opting for use of the driver's
own DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Given the semantic changes in both the device-model and
fc-transport APIs, the driver's handling of port-type RSCNs
via a series of ADISCs and PLOGIs can cause series of
badness ranging from unexpectedly device loss to devices not
being discovered.
In the interim, disable (via a module-parameter) this
feature and allow RSCN management to continue to occur
within the driver's DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similarly to other ISPs, set execution throttle to maximum
allowed value since 'throttling' is done on a per-lun basis
via queue-depth.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify essentially duplicate load RISC RAM implementation
in qla2x00_load_ram_ext() and qla2x00_load_ram().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Swing/emphasis settings in NVRAM were not being honoured due
to the driver not converting the serial-link options from LE
to host-endian format.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the Get Port Database call fails during local-loop
update, then schedule the DPC routine to perform a rescan as
the firmware would have updated the Get ID List port-entries
of their new state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Small changes to register retrieval and order as per latest
firmware specification.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Driver would not correctly re-enable the write-protection
bits of the flash part after updates.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Problem report (against 2.4.x driver) from Jeff Layton
<jlayton@redhat.com>:
An OEM noticed that the U6 qla2200 driver would hang for
around 2 minutes at boot time and then proceed normally. I
found that the delay was occurring when loading the new
firmware into the card, and was due to a
schedule_timeout(10) added to the bottom of the polling
loop.
Some testing showed that the load ram operation on the card
was very quick (on the order of a couple of jiffies), but
the sleep in the polling loop was making each operation take
around 25-30.
The attached patch corrects this by making it skip sleeping
during the load ram operation, since I believe we only do
that when the module is plugged in. It also skips sleeping
if the mbox_int flag got set during the current loop.
This corrected the hang on my test setup, and OEM also
confirmed that it corrected the problem for them.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mailbox commands are polled for completion during ISP
initialization. During potentially 'long' mailbox commands
(i.e. fabric login), we really don't want a busy-wait delay
to potentially trigger a (benign) soft-lockup BUG().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's no point in displaying the message during a valid
underrun case. Limit the message to potentially problematic
cases.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The initial-control-block references are not always correct
as the use-node-name qualifier during NVRAM configuration
will cause the firmware to use the portname as a base for
the nodename.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original From: Adrian Bunk
Here's a composite patch with Adrian's original additions and
help-text with the new Kconfig variable SCSI_QLA_FC.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transition driver to exclusively use the request_firmware()
interfaces to retrieve firmware-blobs from user-space. This
will be the default behaviour going forward until the
embedded firmware-binary images are removed from the
upstream kernel.
Upon request, the driver caches the firmware image until the
driver is unloaded.
NOTE: The option is present to allow the user to continue to
use the firmware-loader modules, but, should be considered
deprecated.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Properly check FC_RESID for any non-transfered bytes
regardless of firmware completion status.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A regression in a recent change
33135aa2a5 caused the driver
to mistakenly drop handling of AENs. Due to the incorrect
handling, ports would not reappear after RSCNs and LIPs.
Drops unused/incorrect compound #define from qla_def.h.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A driver must wait 100us before attempting an MMIO operation
to the RISC after a soft-reset has been initiated. A
similar delay was needed with earlier ISPs.
Note: a PCI config-space read is used to flush the MMIO
write to the ISP, since the ISP's state machines are unable
to respond to any MMIO read during the reset process.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct issue where abort I/O command was not being issued
when the loop-state was down.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When mulitple initiators are coming up in an FCAL topology.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On MMIO relaxed-order platforms, it is possible for the
proper delay during NVRAM access to begin before the request
passes through the PCI bus (via a MMIO write) to the ISP.
Thus, causing a subsequent read to the NVRAM part to fail.
Add a MMIO read, after the MMIO write to insure any posted
writes are flushed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the drivers/scsi/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/scsi/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ok, here's a patch to add such a common API for fc transport users.
Relevant LLD changes (lpfc and qla2xxx) also present.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: 'Andrew Vasquez' <andrew.vasquez@qlogic.com>
Drop scsi_populate_tag_msg() interrogation.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The file is missing an include of scsi_transport_fc.h
drivers/scsi/qla2xxx/qla_rscn.c:334: error: implicit declaration of function 'fc_remote_port_unblock'
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here's a patch which drops the eh_active checks in the qla2xxx
eh_handler callbacks.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While populating command type 6 and 7 IOCBs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ISP23xx and ISP24xx chips have support for an adaptive
method of posting SCSI command completions for multiple SCSI
commands during a single system interrupt.
SCSI commands are placed on the system response queue
without interrupting the host until 1) a delay timer
expires; or 2) a SCSI command completes with an error.
As long as the host software (qla2xxx) services the response
queue for completions (this polling is done during
queuecommand()) within the 'delay timer' period, the
firmware will not generate system interrupt.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The non-handled failure cases of the Fabric Login mailbox
command handling logic would incorrectly mark the fcport as
dead and not allow the standard port-down-retry-count logic
to manage the transition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qla2x00_probe_one()'s call to qla2x00_iospace_config() fails, we call
qla2x00_free_device() to clean up. But because ha->dpc_pid hasn't been set
yet, qla2x00_free_device() tries to stop a kernel thread which hasn't started
yet. It does wait_for_completion() against an uninitialised completion struct
and the kernel hangs up.
Fix it by initialising ha->dpc_pid a bit earlier.
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a hole in the rport unblock handling when processing
fabric events via the ADISC/PLOGI device state machine. Original code
would not properly 'unblock' the port upon the port reloging into the
fabric.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On ISP24xx parts, stop execution of firmware during ISP
tear-down.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Nishanth Aravamudan <nacc@us.ibm.com>
Replace schedule_timeout() with
msleep()/msleep_interruptible() as appropriate, to guarantee the task
delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
fc_remove_host() should only be called after a scsi_host has
been successfully added via scsi_add_host() -- any failures
while qla2xxx probing would result in an incorrect call to
fc_remove_host() during cleanup.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Export additional host information via the shost_attrs member in
the scsi_host template. Attributes include: driver version,
firmware version, ISP serial number, ISP type, ISP product ID,
HBA model name, HBA model description, PCI interconnect
information, and HBA port state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In a corner-case failure where the request-q does not
contain enough entries for a given request, pci_unmap_sg()
would be called twice. Remove direct call and let the
failure-path logic handle the unmapping.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove unnecessary RISC pause/release barriers during
ISP24xx flash manipulation. The ISP24xx can arbitrate flash
access requests during RISC executions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original implementation used an overloaded bit in the EFI
parameters. The correct bit is BIT_4 of the special_options
section of NVRAM.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove redundant qla2x00_target_reset() function in favour of
the equivalent qla2x00_device_reset(). Update callers of
old function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In an FL topology, limit port recognition to those devices
not within the same area and domain of the ISP. The
firmware will recogonize such devices during local-loop
discovery.
Some devices may respond to a PLOGI before they have
completed their fabric login or they may not be a public
device. In this case they will report:
domain == 00
area == 00
alpa == <XX>
which is valid. Exclude such devices from local loop
discovery.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Export COS information for the fc_host and fc_remote_port
objects added by the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In order to efficiently utilise the ISP's IOCB
request-queue, use the dma_get_required_mask() function to
determine the use of command-type 2 or 3 IOCBs when queueing
SCSI commands. This applies to ISP2[123]xx chips only, as
the ISP24xx uses command-type 7 IOCBs which use 64bit DSDs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds the appropriate FW_LOADER pre-requisite and a separate entry
for ISP24xx support.
Thanks to Adrian Bunk and Jesper Juhl for their efforts in fixing this
quirk.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we haven't configured the qla24xx driver, then the Makefile shouldn't
do it for us.
This also means that we can avoid the unnecessary selection of FC_ATTRS.
Debugged by James Bottomley
Older gcc's dont support anonymous unions, so this driver gets hundreds of
error.
Fortunately the fix is easy...
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup FC remote port registration.
Due to the inherent behaviour (an immediate scan) of adding
a 'target'-role-capable rport via fc_remote_port_add(),
split the registration into two steps -- addition as
unknown-type role, then use fc_remote_port_rolchg() with
appropriate role (based on PLOGI/PRLI bits). This allows
for a more cleaner rport->dd_data management as can be seen
with the simplified qla2xxx_slave_alloc() function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Consolidate ISP24xx chip reset logic.
Consolidate near-duplicate RISC reset logic from
qla24xx_reset_chip() and qla24xx_chip_diag(). Also, after
initiating a soft-reset, insure the firmware has completed
all NVRAM accesses before continuing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add firmware version number to qla24xx_fw_version_str().
Original code was accidently trimmed during port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update version number to 8.01.00b5-k.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct maximum supported lun and target-id definitions.
The driver uses command-IOCBs which support a maximum lun
value of 0xffff -- correct #define to reflect the change.
Also, remove superfluous MAX_TARGET definition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NVRAM id-list updates.
Resync with latest NVRAM subsystem ID list.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
