The removed version with the loop registers saved on the stack was
originally intended to workaround the missing toolchain support for
LoopReg Clobbers.
Since our toolchain now supports these there is no point in keeping this
workaround. And since we don't touch LoopRegs anymore we're no longer
subject for ANOMALY_05000312.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Avoid possible overflow during 32*32->32 multiplies.
Reported-by: Marco Reppenhagen <marco.reppenhagen@auerswald.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
use a do...while loop rather than a for loop to get slightly better
optimization and to avoid gcc "may be used uninitialized" warnings ...
we know that the [id]cplb_nr_bounds variables will never be 0, so this
is OK
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Enable null pointer checking for ICPLBs. The code was there but for
some reason I had commented it out at some stage during development.
Should restrict this to 1K since atomic ops start there.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- unable to single step over emuexcpt instruction
- gdbproxy goes into infinite loop when doing gdb does "next" over
"emuexcpt"
Don't decrement PC after software breakpoint.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
bss_l2 section is garbage when the data in this section is used by
_bfin_relocate_l1_mem, so move the zero out function ahead.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
base SIC_IWR# programming on whether the MMR exists
rather than having to maintain another list of processors
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Avoid conditional branch instructions during carry bit additions.
Special thanks to Bernd.
Simplify: Use ((len + proto) << 8) like every other __LITTLE_ENDIAN__ machine
Cc: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- setup P_DEFAULT_BOOT_SPI_CS for every arch based on
the default bootrom behavior and convert all our boards
to it
- revert previous anomaly change ... bf51x is not affected
by anomaly 05000353]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
merge more of the bf54x and !bf54x gpio code together to
cut down on #ifdef mess
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the blackfin
architecture.
Signed-off-by: Uwe Kleine-Koenig <ukleinek@strlen.de>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure we don't accidently re-enable interrupts if we are being
called in atomic context
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
when requesting a GPIO for the first time, the POLAR setting is not
set to a sane state. this can lead to indeterminate behavior that
cannot be resolved without an explicit write to the Blackfin port POLAR
register.
when requesting a GPIO for the first time via gpio_request(), the POLAR
setting for the GPIO in question should be set to sane state. this
should occur if the GPIO has not been allocated in any other way.
some examples:
- when doing something like "request_irq(); gpio_request();" on the
same GPIO, the POLAR setting should not be reset.
- when doing "gpio_request(); gpio_request();" on the same GPIO, the
POLAR setting should be reset only the first time and not the second.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
On BF561 EBIU_SDGCTL bit 31 controls the SDRAM external data
path width, typically set 0 for a 32-bit bus width. On other
Blackfin derivatives this bit should be set by default.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Dmacopy failed in BF537-STAMP when copy from SRAM to SDRAM and kernel
will reboot automatically.
Fixing by doing a SSYNC before mucking with DMA registers
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
powerpc: Fix oops on some machines due to incorrect pr_debug()
powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
powerpc/5200: update device tree binding documentation
powerpc/5200: Bugfix for PCI mapping of memory and IMMR
powerpc/5200: update defconfigs
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Recently, a patch left DEBUG enabled in the powerpc common PCI code,
resulting in an old bug in a pr_debug() statement to show up and cause
a NULL dereference on some machines.
This fixes the pr_debug() statement and reverts to DEBUG not being
force-enabled in that file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, ds, bts: cleanup/fix DS configuration
ring-buffer: reset timestamps when ring buffer is reset
trace: set max latency variable to zero on default
trace: stop all recording to ring buffer on ftrace_dump
trace: print ftrace_dump at KERN_EMERG log level
ring_buffer: reset write when reserve buffer fail
tracing/function-graph-tracer: fix a regression while suspend to disk
ring-buffer: fix alignment problem
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: fix asm constraints in vesa_store_edid
xen: make sysfs files behave as their names suggest
x86: tone down mtrr_trim_uncached_memory() warning
x86: correct the CPUID pattern for MSR_IA32_MISC_ENABLE availability
"flash" is a very generic name for a platform_driver that is only
available on SA11x0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
