When the user executes certain ethtool commands such as -s, -A, -G, -L,
-r a phy reset or autonegotiate is performed which results in management
traffic being interrupted.
Add a warning in these cases.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code unnecessarily resets the phy when we use ethtool to
change the ring parameters or flow control settings. Remove the phy
reset.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The STM45PE20 pinstrap on 5762 devices supports multiple sizes. So treat
it just like the ST45_USPT and the size will be read from 0xf0 via
tg3_get_nvram_size().
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tg3_setup_copper_phy(), if autonegotiation is disabled, we need to
relink only if the speed or duplex does not match the configured
setting. If flow control does not match, a relink is not necessary as
flow control is not a PHY setting. Later on, we'll call
tg3_setup_flow_ctrl() to set up the MAC to the desired flow control
settings if we're in full duplex mode.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to prefetch, in the stmmac_rx, the whole
dma_erx descriptor in case of using the extended descriptors.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
recently many new supports have been added in the stmmac driver w/o taking care
about where each new field had to be placed inside the private structure for
guaranteeing the best cache usage.
This is what I wanted in the beginning, so this patch reorganizes all the fields
in order to keep adjacent fields for cache effect.
I have also tried to optimize them by using pahole.
V2: do not abuse with ____cacheline_aligned_in_smp and keep fields that
potentially could stay in the same cache-line for better usage in SMP systems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidies up the code. I have run Linden (and verified with checkpatch)
many part of the driver trying to reorganize some sections respecting the
codying-style rules in the points where it was not done.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch reviews/improves and adds some fixes in the code doc.
Also kernel-doc passes w/o any warnings.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the pcs mode support for SGMII. Even though
SGMII does auto-negotiation with phy, it needs stmmac_init_phy and
stmmac_mdio_register function for initializing phy.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell mdio driver uses internal registers that can be clock gated on
some SoCs. This patch just adds optional clock handling, to allow to pass
and enable the corresponding clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using module_spi_driver we can eliminate a few lines of boilerplate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a feature is not supported by firmware no need to print an error message.
This surpresses the following harmless message on boot up and ethtool query.
enic: Error 1 devcmd 36
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check KR2 recovery time at the beginning of the work-around function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When our getdcbx entry is called, DCB_CAP_DCBX_HOST should be advertized too.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added readable description for the DPDP and port sensing device capabilities.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The suggestion as following:
- initial settings or default settings
- rtl_hw_start_xxx. rtl_hw_start_xxx may change some default settings.
- enable tx/rx. This has to be after the above two steps.
- rtl_set_rx_mode. AcceptXXXs have to be enabled after enabling tx/rx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- replace rtl8168g-1.fw with rtl8168g-2.fw which support new method.
- fix PHY power down is useless.
- disable rx early which causes the rx abnormal.
- enable auto fifo.
- set 10M IFG to default value.
- fix the conflict between jumbo frame and flow control.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove useless action PHY_READ_EFUSE, PHY_READ_MAC_BYTE, PHY_WRITE_MAC_BYTE,
PHY_WRITE_ERI_WORD. And define the new action PHY_MDIO_CHG.
PHY_MDIO_CHG is used to modify the mdio operation. By the way, the
firmware could support setting mac ocp.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the new settings and correct the wrong settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current settings with rtl_writephy and rtl_readphy.
For the hardware, the settings are same with previous ones. This
make the setting method like the previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some codes are belong to binary codes and should be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limit of 0x3c00 is taken from the windows driver.
Suggested-by: Huang, Xiong <xiong@qca.qualcomm.com>
Cc: Huang, Xiong <xiong@qca.qualcomm.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It would cause no link after suspending or shutdowning when the
nic changes the speed to 10M and connects to a link partner which
forces the speed to 100M.
Check the link partner ability to determine which speed to set.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since of_get_mac_address() is now declared even if CONFIG_OF_NET
is not configured, the ifdef is no longer necessary and can be
removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since of_get_mac_address() is now defined even if CONFIG_OF_NET
is not configured, the ifdef around the code calling it is no longer
necessary and can be removed.
Similar, since of_get_phy_mode() is now defined as dummy function
if OF_NET is not configured, it is no longer necessary to provide
an OF dependent function as front-end. Also, the function depends
on OF_NET, not on OF, so the conditional code was not correct anyway.
Drop the front-end function and call of_get_phy_mode() directly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With of_get_mac_address() and of_get_phy_mode() now defined as dummy
functions if OF_NET is not configured, it is no longer necessary to
provide OF dependent functions as front-end. Also, the two functions
depend on OF_NET, not on OF, so the conditional code was not correct
anyway.
Drop the front-end functions and call of_get_mac_address() and
of_get_phy_mode() directly instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With of_get_mac_address() and of_get_phy_mode() now defined as dummy
functions if OF_NET is not configured, it is no longer necessary to
provide OF dependent functions as front-end. Also, the two functions
depend on OF_NET, not on OF, so the conditional code was not correct
anyway.
Drop the front-end functions and call of_get_mac_address() and
of_get_phy_mode() directly instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
warning: 'pf_info.max_tx_ques' may be used uninitialized in this function
[-Wmaybe-uninitialized]
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix for smatch tool reported error
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c:2029
qlcnic_probe() error: potential NULL dereference 'adapter'.
o While returning from an error path in probe, adapter is not
initialized. So do not access adapter in cleanup path.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[net-next:master 301/302] drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.c:563
qlcnic_set_multi() error: potential null dereference 'cur'. (kzalloc returns null)
o Break out of the loop after memory allocation failure. Program all the
MAC addresses that were cached in the return path.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6bbb6d9 "net/mlx4_en: Optimize Rx fast path filter checks" introduced a regression
under which the MAC address read from the card was not converted correctly
(the most significant byte was not handled), fix that.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug for DM9000 revision B which contain a DSP PHY
DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY,
So need extra change in initialization, For
explicity PHY Reset and PHY init parameter, and
first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe().
Following DM9000_NCR reset cause by dm9000_open() clear the
NCR_MAC_LBK bit.
Without this fix, Power-up FIFO pointers error happen around 2%
rate among Davicom's customers' boards. With this fix, All above
cases can be solved.
Signed-off-by: Joseph CHANG <josright123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the
'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and
the former field gets assigned from the latter. Make the field match, getting
rid of incorrectly used PHY_DOWN value in assignments/comparisons.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its
mask in EESIPR register. I can 100% reproduce it with the following scenario:
target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device
but doesn't get a proper reply and then succeeds with on-board SMC chip; then
I login and try to bring up the SoC Ether device with 'ifconfig', and I get
an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt
mask in EESIPR register is all 0), if that interrupt is accompanied by a pending
EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx()
because sh_eth_ring_init() hasn't been called yet!
The solution I worked out is the following: in sh_eth_interrupt(), mask the
interrupt status from EESR register with the interrupt mask from EESIPR register
in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit
in this mask set because we always need to fully handle EESR.ECI interrupt in
sh_eth_error() in order to quench it (as it doesn't get cleared by just writing
1 to the this bit as all the other interrupts).
While at it, remove unneeded initializer for 'intr_status' variable and give it
*unsigned long* type, matching the type of sh_eth_read()'s result; fix comment.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code handling the absent LINK signal (or the absent PSR register -- which
reflects the state of this signal) is quite naive and has probably never really
worked. It's probably enough to say that this code is executed only on the LINK
change interrupt (sic!) but even if we actually have the signal and choose to
ignore it (it might be connected to PHY's link/activity LED output as on the
Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update
'mdp->link' gets executed later than the LINK change interrupt where it is
checked, and so RX/TX never get enabled via ECMR register.
So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen
not to be used) or PSR register is absent, and enable/disable RX/TX directly in
sh_eth_adjust_link() in this case.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o VFs might get scheduled out after sending a command to a PF
and scheduled in after receiving a response. Implement a
worker thread to handle atomic commands.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for commands from VF to PF.
o PF validates the commands sent by the VF before sending
it to adapter.
o vPort is a container of resources. PF creates vPort
for VFs and attach resources to it. vPort is
transparent to the VF.
o Separate 83xx TX and RX hardware resource cleanup from 82xx.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
