Sampling rate changes after first set one are not reflected to the
hardware, while driver and ALSA think the rate has been changed.
Fix the problem by properly stopping the interface at the beginning of
prepare call, allowing new rate to be set to the hardware. This keeps
the hardware in sync with the driver.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[Problem]
In some USB DACs, a terrible pop noise comes to be heard
at the start of DSD playback (in the following situations).
- play first DSD track
- change from PCM track to DSD track
- change from DSD64 track to DSD128 track (and etc...)
- seek DSD track
- Fast-Forward/Rewind DSD track
[Cause]
At the start of playback, there is a little silence.
The silence bit pattern "0x69" is required on DSD mode,
but it is not like that.
[Solution]
This patch adds DSD silence pattern to the endpoint settings.
Signed-off-by: Nobutaka Okabe <nob77413@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds native DSD support for the following devices.
- TEAC NT-503
- TEAC UD-503
- TEAC UD-501
(1) Add quirks for native DSD support for TEAC devices.
(2) A specific vendor command is needed to switch between PCM/DOP and
DSD mode, same as Denon/Marantz devices.
Signed-off-by: Nobutaka Okabe <nob77413@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Logitech QuickCam Communicate Deluxe/S7500 microphone fails with the
following warning.
[ 6.778995] usb 2-1.2.2.2: Warning! Unlikely big volume range (=3072),
cval->res is probably wrong.
[ 6.778996] usb 2-1.2.2.2: [5] FU [Mic Capture Volume] ch = 1, val =
4608/7680/1
Adding it to the list of devices in volume_control_quirks makes it work
properly, fixing related typo.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Axe-Fx II implicit feedback end point and the data sync endpoint
are in different interface descriptors. Add quirk to ensure a sync
endpoint is properly configured.
Signed-off-by: Alberto Aguirre <albaguirre@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
since commit 57e6dae108 ("ALSA: usb-audio: do not trust too-big
wMaxPacketSize values"), the expected packetsize is always limited
to nominal + 25%. It was discovered, that some devices (Android audio
accessory) have a much higher jitter in used packetsizes than 25%
which would result in BABBLE condition and dropping of packets.
A better solution is so assume the jitter to be the nominal packetsize:
-one nearly empty packet followed by a almost 150% sized one.
V2: changed to assume max frequency is +50 of nominal packetsize.
Signed-off-by: Andreas Pape <apape@de.adit-jv.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some of userland applications call 'snd_pcm_hw_params()' and
'snd_pcm_hw_prepare()' sequentially, which means 'snd_pcm_hw_prepare()'
is called twice and the second 'snd_pcm_hw_prepare()' is called in
'SNDRV_PCM_STATE_PREPARED' state.
Some devices are not able to manage this and they will stop playback
if the sample rate will be configured several times over USB protocol.
V2: updated Changelog
Signed-off-by: Daniel Girnus <dgirnus@de.adit-jv.com>
Signed-off-by: Jens Lorenz <jlorenz@de.adit-jv.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a kernel crash report showing like:
Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = a1d7c000
[00000008] *pgd=31c93831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
CPU: 0 PID: 250 Comm: dbus-daemon Not tainted 3.14.51-03479-gf50bdf4 #1
task: a3ae61c0 ti: a08c8000 task.ti: a08c8000
PC is at retire_capture_urb+0x10/0x1f4 [snd_usb_audio]
LR is at snd_complete_urb+0x140/0x1f0 [snd_usb_audio]
pc : [<7f0eb22c>] lr : [<7f0e57fc>] psr: 200e0193
sp : a08c9c98 ip : a08c9ce8 fp : a08c9ce4
r10: 0000000a r9 : 00000102 r8 : 94cb3000
r7 : 94cb3000 r6 : 94d0f000 r5 : 94d0e8e8 r4 : 94d0e000
r3 : 7f0eb21c r2 : 00000000 r1 : 94cb3000 r0 : 00000000
Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 31d7c04a DAC: 00000015
Process dbus-daemon (pid: 250, stack limit = 0xa08c8238)
Stack: (0xa08c9c98 to 0xa08ca000)
...
Backtrace:
[<7f0eb21c>] (retire_capture_urb [snd_usb_audio]) from [<7f0e57fc>] (snd_complete_urb+0x140/0x1f0 [snd_usb_audio])
[<7f0e56bc>] (snd_complete_urb [snd_usb_audio]) from [<80371118>] (__usb_hcd_giveback_urb+0x78/0xf4)
[<803710a0>] (__usb_hcd_giveback_urb) from [<80371514>] (usb_giveback_urb_bh+0x8c/0xc0)
[<80371488>] (usb_giveback_urb_bh) from [<80028e3c>] (tasklet_hi_action+0xc4/0x148)
[<80028d78>] (tasklet_hi_action) from [<80028358>] (__do_softirq+0x190/0x380)
[<800281c8>] (__do_softirq) from [<80028858>] (irq_exit+0x8c/0xfc)
[<800287cc>] (irq_exit) from [<8000ea88>] (handle_IRQ+0x8c/0xc8)
[<8000e9fc>] (handle_IRQ) from [<800085e8>] (gic_handle_irq+0xbc/0xf8)
[<8000852c>] (gic_handle_irq) from [<80509044>] (__irq_svc+0x44/0x78)
[<80508820>] (_raw_spin_unlock_irq) from [<8004b880>] (finish_task_switch+0x5c/0x100)
[<8004b824>] (finish_task_switch) from [<805052f0>] (__schedule+0x48c/0x6d8)
[<80504e64>] (__schedule) from [<805055d4>] (schedule+0x98/0x9c)
[<8050553c>] (schedule) from [<800116c8>] (do_work_pending+0x30/0xd0)
[<80011698>] (do_work_pending) from [<8000e160>] (work_pending+0xc/0x20)
Code: e1a0c00d e92ddff0 e24cb004 e24dd024 (e5902008)
Kernel panic - not syncing: Fatal exception in interrupt
There is a race between retire_capture_urb() and stop_endpoints().
The latter is called at stopping the stream and it sets some endpoint
fields to NULL. But its call is asynchronous, thus the pending
complete callback might get called after these NULL clears, and it
leads the NULL dereference like the above.
The fix is to move the NULL clearance after the synchronization,
i.e. wait_clear_urbs(). This is called at prepare and hw_free
callbacks, so it's assured to be called before the restart of the
stream or the release of the stream.
Also, while we're at it, put the EP_FLAG_RUNNING flag check at the
beginning of snd_complete_urb() to skip the pending complete after the
stream is stopped.
Fixes: b2eb950de2 ("ALSA: usb-audio: stop both data and sync...")
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Reported-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function returns -EINVAL even if it builds the stream properly.
The bogus error code sneaked in during the code refactoring, but it
wasn't noticed until now since the returned error code itself is
ignored in anyway. Kill it here, but there is no behavior change by
this patch, obviously.
Fixes: e5779998bf ('ALSA: usb-audio: refactor code')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Userspace apps have to claim USB interfaces before using endpoints in
them (drivers/usb/core/devio.c:checkintf()). It's a lock mechanism so
that two "drivers" don't steal data from each other. Kernel drivers don't
have to claim interfaces to work - but they should, to lock out userspace.
While there, fix line6_properties struct to match checkpatch.pl.
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The usb-audio driver implements the deferred device disconnection for
the device in use. In this mode, the disconnection callback returns
immediately while the actual ALSA card object removal happens later
when all files get closed. As Shuah reported, this code flow,
however, leads to a use-after-free, detected by KASAN:
BUG: KASAN: use-after-free in snd_usb_audio_free+0x134/0x160 [snd_usb_audio] at addr ffff8801c863ce10
Write of size 8 by task pulseaudio/2244
Call Trace:
[<ffffffff81b31473>] dump_stack+0x67/0x94
[<ffffffff81564ef1>] kasan_object_err+0x21/0x70
[<ffffffff8156518a>] kasan_report_error+0x1fa/0x4e0
[<ffffffff81564ad7>] ? kasan_slab_free+0x87/0xb0
[<ffffffff81565733>] __asan_report_store8_noabort+0x43/0x50
[<ffffffffa0fc0f54>] ? snd_usb_audio_free+0x134/0x160 [snd_usb_audio]
[<ffffffffa0fc0f54>] snd_usb_audio_free+0x134/0x160 [snd_usb_audio]
[<ffffffffa0fc0fb1>] snd_usb_audio_dev_free+0x31/0x40 [snd_usb_audio]
[<ffffffff8243c78a>] __snd_device_free+0x12a/0x210
[<ffffffff8243d1f5>] snd_device_free_all+0x85/0xd0
[<ffffffff8242cae4>] release_card_device+0x34/0x130
[<ffffffff81ef1846>] device_release+0x76/0x1e0
[<ffffffff81b37ad7>] kobject_release+0x107/0x370
.....
Object at ffff8801c863cc80, in cache kmalloc-2048 size: 2048
Allocated:
[<ffffffff810804eb>] save_stack_trace+0x2b/0x50
[<ffffffff81564296>] save_stack+0x46/0xd0
[<ffffffff8156450d>] kasan_kmalloc+0xad/0xe0
[<ffffffff81560d1a>] kmem_cache_alloc_trace+0xfa/0x240
[<ffffffff8214ea47>] usb_alloc_dev+0x57/0xc90
[<ffffffff8216349d>] hub_event+0xf1d/0x35f0
....
Freed:
[<ffffffff810804eb>] save_stack_trace+0x2b/0x50
[<ffffffff81564296>] save_stack+0x46/0xd0
[<ffffffff81564ac1>] kasan_slab_free+0x71/0xb0
[<ffffffff81560929>] kfree+0xd9/0x280
[<ffffffff8214de6e>] usb_release_dev+0xde/0x110
[<ffffffff81ef1846>] device_release+0x76/0x1e0
....
It's the code trying to clear drvdata of the assigned usb_device where
the usb_device itself was already released in usb_release_dev() after
the disconnect callback.
This patch fixes it by checking whether the code path is via the
disconnect callback, i.e. chip->shutdown flag is set.
Fixes: 79289e2419 ('ALSA: usb-audio: Refer to chip->usb_id for quirks...')
Reported-and-tested-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The error checking here is messed up so we could end up dereferencing
-EFAULT.
Fixes: a16039cbf1 ('ALSA: line6: Add hwdep interface to access the POD control messages')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit c039aaa77a was incomplete,
missing part of the setup for Live. This makes also audio input work,
in addition to audio output.
Fixes: c039aaa77a
Reported-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, usb-line6 module exports an array of MIDI manufacturer ID and
usb-pod module uses it. However, the declaration is not the definition in
common header. The difference is explicit length of array. Although
compiler calculates it and everything goes well, it's better to use the
same representation between definition and declaration.
This commit fills the length of array for usb-line6 module. As a small
good sub-effect, this commit suppress below warnings from static analysis
by sparse v0.5.0.
sound/usb/line6/driver.c:274:43: error: cannot size expression
sound/usb/line6/driver.c:275:16: error: cannot size expression
sound/usb/line6/driver.c:276:16: error: cannot size expression
sound/usb/line6/driver.c:277:16: error: cannot size expression
Fixes: 705ececd1c ("Staging: add line6 usb driver")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DragonFly quirk added in 42e3121d90 ("ALSA: usb-audio: Add a more
accurate volume quirk for AudioQuest DragonFly") applies a custom dB map
on the volume control when its range is reported as 0..50 (0 .. 0.2dB).
However, there exists at least one other variant (hw v1.0c, as opposed
to the tested v1.2) which reports a different non-sensical volume range
(0..53) and the custom map is therefore not applied for that device.
This results in all of the volume change appearing close to 100% on
mixer UIs that utilize the dB TLV information.
Add a fallback case where no dB TLV is reported at all if the control
range is not 0..50 but still 0..N where N <= 1000 (3.9 dB). Also
restrict the quirk to only apply to the volume control as there is also
a mute control which would match the check otherwise.
Fixes: 42e3121d90 ("ALSA: usb-audio: Add a more accurate volume quirk for AudioQuest DragonFly")
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: David W <regulars@d-dub.org.uk>
Tested-by: David W <regulars@d-dub.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/usb/line6/driver.c:484:2-7: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Generated by: scripts/coccinelle/free/ifnullfree.cocci
CC: Andrej Krutak <dev@andree.sk>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We must do it this way, because e.g. POD X3 won't play any sound unless
the host listens on the bulk EP, so we cannot export it only via libusb.
The driver currently doesn't use the bulk EP messages in other way,
in future it could e.g. sense/modify volume(s).
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only initialize PCM for POD HD devices that support it.
No POD HD seems to support MIDI, thus drop the initialization.
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This includes audio in/out and basic initialization via control EP (emulates
what original driver does). The initialization is done similarly to original
POD, firmware and serial IDs are read and exported via sysfs.
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not all PODs use MIDI via USB data interface, thus allow avoiding
that code and instead using direct processing.
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
POD X3 can initialize similarly to older PODs, but it doesn't have the MIDI
interface. Instead, configuration is done via proprietary bulk EP messages.
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
E.g. POD X3 seems to require playback data to be sent to it to generate
capture data. Otherwise the device stalls and doesn't send any more capture
data until it's reset.
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Splits max_packet_size to max_packet_size_in/out (e.g. for
different channel counts).
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This has two parts:
* intervals_per_second setup
(high speed needs 8000, instead of 1000)
* iso_buffers setup (count of iso buffers depends on
USB speed, 2 is not enough for high speed)
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This basically changes LINE6_ISO_BUFFERS constant to a configurable
iso_buffers property.
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Avoid getting sample rate on B850V3 CP2114 as it is unsupported and
causes noisy "current rate is different from the runtime rate" messages
when playback starts.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kmalloc already print similar error once failing to alloc
enough memory, so let's remove this dump here.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Users of devices affected by the Tenor feedback data error report
buffer underruns, even with the +/- 0x1.0000 quirk applied.
Compensating the error with 0xf000 instead seems to reliably fix
that issue.
See
https://sourceforge.net/p/alsa/mailman/message/35230259/
Reported-and-tested-by: Norman Nolte <norman.nolte@gmx.net>
Reported-and-tested-by: Thomas Gresens <T.Gresens@intershop.de>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirk seems to be necessary not only for TEAC UD-H01 devices, but to
more that are based on the Tenor 8802TL chipset. Devices built by T+A
are affected too, and they apparently all use the same USB PID:PID.
Extend the quirky handling for that device as well, and rename the
quirks flag.
Reported-and-tested-by: Thomas Gresens <T.Gresens@intershop.de>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
That's a quirk, after all, so move it where to all the other quirks
live.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 02fc76f6a changed base of the sysfs attributes from device to card.
The "show" callbacks dereferenced wrong objects because of this.
Fixes: 02fc76f6a7 ('ALSA: line6: Create sysfs via snd_card_add_dev_attr()')
Cc: <stable@vger.kernel.org> # v4.0+
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If there's an error, pcm is released in line6_pcm_acquire already.
Fixes: 247d95ee6d ('ALSA: line6: Handle error from line6_pcm_acquire()')
Cc: <stable@vger.kernel.org> # v4.0+
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ELP HD USB Camera (05a3:9420) needs this quirk for suppressing
the unsupported sample rate inquiry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98481
Cc: <stable@vger.kernel.org>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VF0610 does not support reading the sample rate which leads to many
lines of "cannot get freq at ep 0x82". This patch adds the USB ID
(0x041E:4080) to snd_usb_get_sample_rate_quirk() list.
Signed-off-by: Piotr Karasinski <peter.karasinski@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To allow for structure randomisation, replace the in order struct
initialisation style with explicit field style.
The Coccinelle semantic patch used to make this change is as follows:
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@@
identifier decl.i1,i2,decl.fld;
expression e;
position bad.p, bad.fix;
@@
struct i1 i2@p = { ...,
+ .fld = e
- e@fix
,...};
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Phoenix Audio has yet another device with another id (even a different
vendor id, 0556:0014) that requires the same quirk for the sample
rate.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
