[ Upstream commit 9de2b9286a6dd16966959b3cb34fc2ddfd39213e ]
Yes, you are right and now the return code depending on the
init_clks().
Fixes: 6078c65194 ("soc: mediatek: Refine scpsys to support multiple platform")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20211222015157.1025853-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e1fcab00a23f7fe9f4fe9704905a790efa1eeab ]
John Garry reported a deadlock that occurs when trying to access a
runtime-suspended SATA device. For obscure reasons, the rescan procedure
causes the link to be hard-reset, which disconnects the device.
The rescan tries to carry out a runtime resume when accessing the device.
scsi_rescan_device() holds the SCSI device lock and won't release it until
it can put commands onto the device's block queue. This can't happen until
the queue is successfully runtime-resumed or the device is unregistered.
But the runtime resume fails because the device is disconnected, and
__scsi_remove_device() can't do the unregistration because it can't get the
device lock.
The best way to resolve this deadlock appears to be to allow the block
queue to start running again even after an unsuccessful runtime resume.
The idea is that the driver or the SCSI error handler will need to be able
to use the queue to resolve the runtime resume failure.
This patch removes the err argument to blk_post_runtime_resume() and makes
the routine act as though the resume was successful always. This fixes the
deadlock.
Link: https://lore.kernel.org/r/1639999298-244569-4-git-send-email-chenxiang66@hisilicon.com
Fixes: e27829dc92 ("scsi: serialize ->rescan against ->remove")
Reported-and-tested-by: John Garry <john.garry@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7061627d701c90e1cac1e1e60c45292f64f3470 ]
It turns out to be possible for hotplugging out a device to reach the
stage of tearing down the device's group and default domain before the
domain's flush queue has drained naturally. At this point, it is then
possible for the timeout to expire just before the del_timer() call
in free_iova_flush_queue(), such that we then proceed to free the FQ
resources while fq_flush_timeout() is still accessing them on another
CPU. Crashes due to this have been observed in the wild while removing
NVMe devices.
Close the race window by using del_timer_sync() to safely wait for any
active timeout handler to finish before we start to free things. We
already avoid any locking in free_iova_flush_queue() since the FQ is
supposed to be inactive anyway, so the potential deadlock scenario does
not apply.
Fixes: 9a005a800a ("iommu/iova: Add flush timer")
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[ rm: rewrite commit message ]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0a365e5b07f14b7344677ad6a9a734966a8422ce.1639753638.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a9a72e290d4a4741e673f86b9fba9bfb319786d ]
After calling dmaengine_submit(), the submitted transfer descriptor
belongs to the DMA engine. Pointer to that descriptor may no longer be
valid after the call and should be tested before awaiting transfer
completion.
Reported-by: Kevin Tian <kevin.tian@intel.com>
Suggested-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 4fac9b31d0 ("ASoC: Intel: Add catpt base members")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211216115743.2130622-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8d4a37d1bb93608501d0d0545f902061152669a ]
This will give IOMMU GA log a chance to work after resume
from s3/s4.
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20211123161038.48009-2-mlevitsk@redhat.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb03f2d2f6a4da25d286613717d10add9ce9f175 ]
Since the function has been simplified and only call iommu_init_ga_log(),
remove the function and replace with iommu_init_ga_log() instead.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210820202957.187572-4-suravee.suthikulpanit@amd.com
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 134c37fa250a87a7e77c80a7c59ae16c462e46e0 ]
The last driver referencing the slave_id on Marvell PXA and MMP platforms
was the SPI driver, but this stopped doing so a long time ago, so the
TODO from the earlier patch can no be removed.
Fixes: b729bf3453 ("spi/pxa2xx: Don't use slave_id of dma_slave_config")
Fixes: 13b3006b8e ("dma: mmp_pdma: add filter function")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-7-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a670c82d9ca4f1e7385d9d6f26ff41a50fbdd944 ]
Commit d4a451d5fc ("arch: remove the ARCH_PHYS_ADDR_T_64BIT config
symbol") removes config ARCH_PHYS_ADDR_T_64BIT with all instances of that
config refactored appropriately. Since then, it is recommended to use the
config PHYS_ADDR_T_64BIT instead.
Commit 171543e752 ("MIPS: Disallow CPU_SUPPORTS_HUGEPAGES for XPA,EVA")
introduces the expression "!(32BIT && (ARCH_PHYS_ADDR_T_64BIT || EVA))"
for config CPU_SUPPORTS_HUGEPAGES, which unintentionally refers to the
non-existing symbol ARCH_PHYS_ADDR_T_64BIT instead of the intended
PHYS_ADDR_T_64BIT.
Fix this Kconfig reference to the intended PHYS_ADDR_T_64BIT.
This issue was identified with the script ./scripts/checkkconfigsymbols.py.
I then reported it on the mailing list and Paul confirmed the mistake in
the linked email thread.
Link: https://lore.kernel.org/lkml/H8IU3R.H5QVNRA077PT@crapouillou.net/
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 171543e752 ("MIPS: Disallow CPU_SUPPORTS_HUGEPAGES for XPA,EVA")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd4eb90b164442cb1e9909f7845e12a0835ac699 ]
Commit ab7c01fdc3 ("mips: Add MIPS Release 5 support") adds the two
configs CPU_MIPS32_R5 and CPU_MIPS64_R5, which depend on the corresponding
SYS_HAS_CPU_MIPS32_R5 and SYS_HAS_CPU_MIPS64_R5, respectively.
The config SYS_HAS_CPU_MIPS32_R5 was already introduced with commit
c5b367835c ("MIPS: Add support for XPA."); the config
SYS_HAS_CPU_MIPS64_R5, however, was never introduced.
Hence, ./scripts/checkkconfigsymbols.py warns:
SYS_HAS_CPU_MIPS64_R5
Referencing files: arch/mips/Kconfig, arch/mips/include/asm/cpu-type.h
Add the definition for config SYS_HAS_CPU_MIPS64_R5 under the assumption
that SYS_HAS_CPU_MIPS64_R5 follows the same pattern as the existing
SYS_HAS_CPU_MIPS32_R5 and SYS_HAS_CPU_MIPS64_R6.
Fixes: ab7c01fdc3 ("mips: Add MIPS Release 5 support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fc058a72f3b7b07fc4de6d66ad1f68951b00f6e ]
stm32's clk driver register two ltdc gate clk to clk core by
clk_hw_register_gate() and clk_hw_register_composite()
first: 'stm32f429_gates[]', clk name is 'ltdc', which no user to use.
second: 'stm32f429_aux_clk[]', clk name is 'lcd-tft', used by ltdc driver
both of them point to the same offset of stm32's RCC register. after
kernel enter console, clk core turn off ltdc's clk as 'stm32f429_gates[]'
is no one to use. but, actually 'stm32f429_aux_clk[]' is in use.
stm32f469/746/769 have the same issue, fix it.
Fixes: daf2d117cb ("clk: stm32f4: Add lcd-tft clock")
Link: https://lore.kernel.org/linux-arm-kernel/1590564453-24499-7-git-send-email-dillon.minfei@gmail.com/
Link: https://lore.kernel.org/lkml/CAPTRvHkf0cK_4ZidM17rPo99gWDmxgqFt4CDUjqFFwkOeQeFDg@mail.gmail.com/
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/1635232282-3992-10-git-send-email-dillon.minfei@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fd4cf5d3571b27d746b8ead494a3f051485b679 ]
If an architecture does not support 64 bit dma addresses then testing
for an expected dma address >= 0x100000000 will fail.
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211212221852.233295-1-frowand.list@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8d61a9112ad0c9216ab45d050991e07bc4f3408 ]
The struct device variable "dev_bogus" was triggering this warning
on a PowerPC build:
drivers/of/unittest.c: In function 'of_unittest_dma_ranges_one.constprop':
[...] >> The frame size of 1424 bytes is larger than 1024 bytes
[-Wframe-larger-than=]
This variable is now dynamically allocated.
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211210184636.7273-2-jim2101024@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2167c0b205960607fb136b4bb3c556a62be1569a ]
The return value of device_property_read_u32_array() is not always 0.
To catch the exception in case that devm_kzalloc failed and the
rt5663->imp_table was NULL, which caused the failure of
device_property_read_u32_array.
Fixes: 450f0f6a8f ("ASoC: rt5663: Add the manual offset field to compensate the DC offset")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20211215031550.70702-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20679094a0161c94faf77e373fa3f7428a8e14bd ]
Currently, when cma_resolve_ib_dev() searches for a matching GID it will
stop searching after encountering the first empty GID table entry. This
behavior is wrong since neither IB nor RoCE spec enforce tightly packed
GID tables.
For example, when the matching valid GID entry exists at index N, and if a
GID entry is empty at index N-1, cma_resolve_ib_dev() will fail to find
the matching valid entry.
Fix it by making cma_resolve_ib_dev() continue searching even after
encountering missing entries.
Fixes: f17df3b0de ("RDMA/cma: Add support for AF_IB to rdma_resolve_addr()")
Link: https://lore.kernel.org/r/b7346307e3bb396c43d67d924348c6c496493991.1639055490.git.leonro@nvidia.com
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483d805191a23191f8294bbf9b4e94836f5d92e4 ]
Currently, ib_find_gid() will stop searching after encountering the first
empty GID table entry. This behavior is wrong since neither IB nor RoCE
spec enforce tightly packed GID tables.
For example, when a valid GID entry exists at index N, and if a GID entry
is empty at index N-1, ib_find_gid() will fail to find the valid entry.
Fix it by making ib_find_gid() continue searching even after encountering
missing entries.
Fixes: 5eb620c81c ("IB/core: Add helpers for uncached GID and P_Key searches")
Link: https://lore.kernel.org/r/e55d331b96cecfc2cf19803d16e7109ea966882d.1639055490.git.leonro@nvidia.com
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b149d5d45ac9171ed699a256f026c8ebef901112 ]
Commit df1f679d19ed ("powerpc/powermac: Add missing
lockdep_register_key()") fixed a problem that was causing a WARNING.
There are two other places in the same file with the same problem
originating from commit 9e607f7274 ("i2c_powermac: shut up lockdep
warning").
Add missing lockdep_register_key()
Fixes: 9e607f7274 ("i2c_powermac: shut up lockdep warning")
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Depends-on: df1f679d19ed ("powerpc/powermac: Add missing lockdep_register_key()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200055
Link: https://lore.kernel.org/r/2c7e421874e21b2fb87813d768cf662f630c2ad4.1638984999.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29bbc35e29d9b6347780dcacde2deb4b39344167 ]
pci_irq_vector() and pci_irq_get_affinity() use the list position to find the
MSI-X descriptor at a given index. That's correct for the normal case where
the entry number is the same as the list position.
But it's wrong for cases where MSI-X was allocated with an entries array
describing sparse entry numbers into the hardware message descriptor
table. That's inconsistent at best.
Make it always check the entry number because that's what the zero base
index really means. This change won't break existing users which use a
sparse entries array for allocation because these users retrieve the Linux
interrupt number from the entries array after allocation and none of them
uses pci_irq_vector() or pci_irq_get_affinity().
Fixes: aff171641d ("PCI: Provide sensible IRQ vector alloc/free routines")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211206210223.929792157@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a4da64bfc189510e08df1ccb1c589e667dc7a3 ]
Fix the wrongly reported max_send_wr and max_recv_wr attributes for user
QP by making sure to save their valuse on QP creation, so when query QP is
called the attributes will be reported correctly.
Fixes: cecbcddf64 ("qedr: Add support for QP verbs")
Link: https://lore.kernel.org/r/20211206201314.124947-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21ad0e49085deb22c094f91f9da57319a97188e4 ]
The driver data pointer must be set before any callbacks are registered
that use that pointer. Hence move the initialization of that pointer from
after the ufshcd_init() call to inside ufshcd_init().
Link: https://lore.kernel.org/r/20211203231950.193369-7-bvanassche@acm.org
Fixes: 3b1d05807a ("[SCSI] ufs: Segregate PCI Specific Code")
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9abe2ac834851a7d0b0756e295cf7a292c45ca53 ]
Table descriptors were being installed without properly formatting the
address using paddr_to_iopte, which does not match up with the
iopte_deref in __arm_lpae_map. This is incorrect for the LPAE pte
format, as it does not handle the high bits properly.
This was found on Apple T6000 DARTs, which require a new pte format
(different shift); adding support for that to
paddr_to_iopte/iopte_to_paddr caused it to break badly, as even <48-bit
addresses would end up incorrect in that case.
Fixes: 6c89928ff7 ("iommu/io-pgtable-arm: Support 52-bit physical address")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20211120031343.88034-1-marcan@marcan.st
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 433fe39f674d58bc7a3e8254a5d2ffc290b7e04e ]
Like fork and clone the clone3 syscall needs a wrapper to save callee
saved registers, which is required by the OpenRISC ABI. This came up
after auditing code following a discussion with Rob Landley and Arnd
Bergmann [0].
Tested with the clone3 kselftests and there were no issues.
[0] https://lore.kernel.org/all/41206fc7-f8ce-98aa-3718-ba3e1431e320@landley.net/T/#m9c0cdb2703813b9df4da04cf6b30de1f1aa89944
Fixes: 07e83dfbe1 ("openrisc: Enable the clone3 syscall")
Cc: Rob Landley <rob@landley.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe6b1869243f23a485a106c214bcfdc7aa0ed593 ]
If a memory copy function fails to copy the whole buffer,
a positive integar with the remaining bytes is returned.
In binder_translate_fd_array() this can result in an fd being
skipped due to the failed copy, but the loop continues
processing fds since the early return condition expects a
negative integer on error.
Fix by returning "ret > 0 ? -EINVAL : ret" to handle this case.
Fixes: bb4a2e48d5 ("binder: return errors from buffer copy functions")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211130185152.437403-2-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5912cc19acd7c24b2dbf65a6340bf194244f085 ]
Using MKWORD() on a byte-sized variable results in OOB read. Expand the
size of the reserved area so both MKWORD and MKBYTE continue to work
without overflow. Silences this warning on a -Warray-bounds build:
drivers/char/mwave/3780i.h:346:22: error: array subscript 'short unsigned int[0]' is partly outside array bounds of 'DSP_ISA_SLAVE_CONTROL[1]' [-Werror=array-bounds]
346 | #define MKWORD(var) (*((unsigned short *)(&var)))
| ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/char/mwave/3780i.h:356:40: note: in definition of macro 'OutWordDsp'
356 | #define OutWordDsp(index,value) outw(value,usDspBaseIO+index)
| ^~~~~
drivers/char/mwave/3780i.c:373:41: note: in expansion of macro 'MKWORD'
373 | OutWordDsp(DSP_IsaSlaveControl, MKWORD(rSlaveControl));
| ^~~~~~
drivers/char/mwave/3780i.c:358:31: note: while referencing 'rSlaveControl'
358 | DSP_ISA_SLAVE_CONTROL rSlaveControl;
| ^~~~~~~~~~~~~
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211203084206.3104326-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e583aef12aa74afd37c1418255cc4b74e023236 ]
The vendor ID of Presonus Studio 1810c had a superfluous '0' in its
USB ID. Drop it.
Fixes: 8dc5efe3d1 ("ALSA: usb-audio: Add support for Presonus Studio 1810c")
Link: https://lore.kernel.org/r/20211202083833.17784-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e7daf318d97f25e18b2fc7eb5909e34cd903575 ]
Fix compile error when OSS_DEBUG is enabled:
sound/core/oss/pcm_oss.c: In function 'snd_pcm_oss_set_trigger':
sound/core/oss/pcm_oss.c:2055:10: error: 'substream' undeclared (first
use in this function); did you mean 'csubstream'?
pcm_dbg(substream->pcm, "pcm_oss: trigger = 0x%x\n", trigger);
^
Fixes: 61efcee860 ("ALSA: oss: Use standard printk helpers")
Signed-off-by: Bixuan Cui <cuibixuan@linux.alibaba.com>
Link: https://lore.kernel.org/r/1638349134-110369-1-git-send-email-cuibixuan@linux.alibaba.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c86ff8c55b8ae68837b2fa59dc0c203907e9a15f ]
Since commit db3a34e17433 ("clocksource: Retry clock read if long delays
detected") and commit 2e27e793e280 ("clocksource: Reduce clocksource-skew
threshold"), it is found that tsc clocksource fallback to hpet can
sometimes happen on both Intel and AMD systems especially when they are
running stressful benchmarking workloads. Of the 23 systems tested with
a v5.14 kernel, 10 of them have switched to hpet clock source during
the test run.
The result of falling back to hpet is a drastic reduction of performance
when running benchmarks. For example, the fio performance tests can
drop up to 70% whereas the iperf3 performance can drop up to 80%.
4 hpet fallbacks happened during bootup. They were:
[ 8.749399] clocksource: timekeeping watchdog on CPU13: hpet read-back delay of 263750ns, attempt 4, marking unstable
[ 12.044610] clocksource: timekeeping watchdog on CPU19: hpet read-back delay of 186166ns, attempt 4, marking unstable
[ 17.336941] clocksource: timekeeping watchdog on CPU28: hpet read-back delay of 182291ns, attempt 4, marking unstable
[ 17.518565] clocksource: timekeeping watchdog on CPU34: hpet read-back delay of 252196ns, attempt 4, marking unstable
Other fallbacks happen when the systems were running stressful
benchmarks. For example:
[ 2685.867873] clocksource: timekeeping watchdog on CPU117: hpet read-back delay of 57269ns, attempt 4, marking unstable
[46215.471228] clocksource: timekeeping watchdog on CPU8: hpet read-back delay of 61460ns, attempt 4, marking unstable
Commit 2e27e793e280 ("clocksource: Reduce clocksource-skew threshold"),
changed the skew margin from 100us to 50us. I think this is too small
and can easily be exceeded when running some stressful workloads on a
thermally stressed system. So it is switched back to 100us.
Even a maximum skew margin of 100us may be too small in for some systems
when booting up especially if those systems are under thermal stress. To
eliminate the case that the large skew is due to the system being too
busy slowing down the reading of both the watchdog and the clocksource,
an extra consecutive read of watchdog clock is being done to check this.
The consecutive watchdog read delay is compared against
WATCHDOG_MAX_SKEW/2. If the delay exceeds the limit, we assume that
the system is just too busy. A warning will be printed to the console
and the clock skew check is skipped for this round.
Fixes: db3a34e17433 ("clocksource: Retry clock read if long delays detected")
Fixes: 2e27e793e280 ("clocksource: Reduce clocksource-skew threshold")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e27e793e280ff12cb5c202a1214c08b0d3a0f26 ]
Currently, WATCHDOG_THRESHOLD is set to detect a 62.5-millisecond skew in
a 500-millisecond WATCHDOG_INTERVAL. This requires that clocks be skewed
by more than 12.5% in order to be marked unstable. Except that a clock
that is skewed by that much is probably destroying unsuspecting software
right and left. And given that there are now checks for false-positive
skews due to delays between reading the two clocks, it should be possible
to greatly decrease WATCHDOG_THRESHOLD, at least for fine-grained clocks
such as TSC.
Therefore, add a new uncertainty_margin field to the clocksource structure
that contains the maximum uncertainty in nanoseconds for the corresponding
clock. This field may be initialized manually, as it is for
clocksource_tsc_early and clocksource_jiffies, which is copied to
refined_jiffies. If the field is not initialized manually, it will be
computed at clock-registry time as the period of the clock in question
based on the scale and freq parameters to __clocksource_update_freq_scale()
function. If either of those two parameters are zero, the
tens-of-milliseconds WATCHDOG_THRESHOLD is used as a cowardly alternative
to dividing by zero. No matter how the uncertainty_margin field is
calculated, it is bounded below by twice WATCHDOG_MAX_SKEW, that is, by 100
microseconds.
Note that manually initialized uncertainty_margin fields are not adjusted,
but there is a WARN_ON_ONCE() that triggers if any such field is less than
twice WATCHDOG_MAX_SKEW. This WARN_ON_ONCE() is intended to discourage
production use of the one-nanosecond uncertainty_margin values that are
used to test the clock-skew code itself.
The actual clock-skew check uses the sum of the uncertainty_margin fields
of the two clocksource structures being compared. Integer overflow is
avoided because the largest computed value of the uncertainty_margin
fields is one billion (10^9), and double that value fits into an
unsigned int. However, if someone manually specifies (say) UINT_MAX,
they will get what they deserve.
Note that the refined_jiffies uncertainty_margin field is initialized to
TICK_NSEC, which means that skew checks involving this clocksource will
be sufficently forgiving. In a similar vein, the clocksource_tsc_early
uncertainty_margin field is initialized to 32*NSEC_PER_MSEC, which
replicates the current behavior and allows custom setting if needed
in order to address the rare skews detected for this clocksource in
current mainline.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-4-paulmck@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9ac51b850d84ee496b0a5d832ce66d411ae552 ]
Running perf fuzzer showed below in dmesg logs:
"Can't find PMC that caused IRQ"
This means a PMU exception happened, but none of the PMC's (Performance
Monitor Counter) were found to be overflown. There are some corner cases
that clears the PMCs after PMI gets masked. In such cases, the perf
interrupt handler will not find the active PMC values that had caused
the overflow and thus leads to this message while replaying.
Case 1: PMU Interrupt happens during replay of other interrupts and
counter values gets cleared by PMU callbacks before replay:
During replay of interrupts like timer, __do_irq() and doorbell
exception, we conditionally enable interrupts via may_hard_irq_enable().
This could potentially create a window to generate a PMI. Since irq soft
mask is set to ALL_DISABLED, the PMI will get masked here. We could get
IPIs run before perf interrupt is replayed and the PMU events could
be deleted or stopped. This will change the PMU SPR values and resets
the counters. Snippet of ftrace log showing PMU callbacks invoked in
__do_irq():
<idle>-0 [051] dns. 132025441306354: __do_irq <-call_do_irq
<idle>-0 [051] dns. 132025441306430: irq_enter <-__do_irq
<idle>-0 [051] dns. 132025441306503: irq_enter_rcu <-__do_irq
<idle>-0 [051] dnH. 132025441306599: xive_get_irq <-__do_irq
<<>>
<idle>-0 [051] dnH. 132025441307770: generic_smp_call_function_single_interrupt <-smp_ipi_demux_relaxed
<idle>-0 [051] dnH. 132025441307839: flush_smp_call_function_queue <-smp_ipi_demux_relaxed
<idle>-0 [051] dnH. 132025441308057: _raw_spin_lock <-event_function
<idle>-0 [051] dnH. 132025441308206: power_pmu_disable <-perf_pmu_disable
<idle>-0 [051] dnH. 132025441308337: power_pmu_del <-event_sched_out
<idle>-0 [051] dnH. 132025441308407: power_pmu_read <-power_pmu_del
<idle>-0 [051] dnH. 132025441308477: read_pmc <-power_pmu_read
<idle>-0 [051] dnH. 132025441308590: isa207_disable_pmc <-power_pmu_del
<idle>-0 [051] dnH. 132025441308663: write_pmc <-power_pmu_del
<idle>-0 [051] dnH. 132025441308787: power_pmu_event_idx <-perf_event_update_userpage
<idle>-0 [051] dnH. 132025441308859: rcu_read_unlock_strict <-perf_event_update_userpage
<idle>-0 [051] dnH. 132025441308975: power_pmu_enable <-perf_pmu_enable
<<>>
<idle>-0 [051] dnH. 132025441311108: irq_exit <-__do_irq
<idle>-0 [051] dns. 132025441311319: performance_monitor_exception <-replay_soft_interrupts
Case 2: PMI's masked during local_* operations, example local_add(). If
the local_add() operation happens within a local_irq_save(), replay of
PMI will be during local_irq_restore(). Similar to case 1, this could
also create a window before replay where PMU events gets deleted or
stopped.
Fix it by updating the PMU callback function power_pmu_disable() to
check for pending perf interrupt. If there is an overflown PMC and
pending perf interrupt indicated in paca, clear the PMI bit in paca to
drop that sample. Clearing of PMI bit is done in power_pmu_disable()
since disable is invoked before any event gets deleted/stopped. With
this fix, if there are more than one event running in the PMU, there is
a chance that we clear the PMI bit for the event which is not getting
deleted/stopped. The other events may still remain active. Hence to make
sure we don't drop valid sample in such cases, another check is added in
power_pmu_enable. This checks if there is an overflown PMC found among
the active events and if so enable back the PMI bit. Two new helper
functions are introduced to clear/set the PMI, ie
clear_pmi_irq_pending() and set_pmi_irq_pending(). Helper function
pmi_irq_pending() is introduced to give a warning if there is pending
PMI bit in paca, but no PMC is overflown.
Also there are corner cases which result in performance monitor
interrupts being triggered during power_pmu_disable(). This happens
since PMXE bit is not cleared along with disabling of other MMCR0 bits
in the pmu_disable. Such PMI's could leave the PMU running and could
trigger PMI again which will set MMCR0 PMAO bit. This could lead to
spurious interrupts in some corner cases. Example, a timer after
power_pmu_del() which will re-enable interrupts and triggers a PMI again
since PMAO bit is still set. But fails to find valid overflow since PMC
was cleared in power_pmu_del(). Fix that by disabling PMXE along with
disabling of other MMCR0 bits in power_pmu_disable().
We can't just replay PMI any time. Hence this approach is preferred
rather than replaying PMI before resetting overflown PMC. Patch also
documents core-book3s on a race condition which can trigger these PMC
messages during idle path in PowerNV.
Fixes: f442d00480 ("powerpc/64s: Add support to mask perf interrupts and replay them")
Reported-by: Nageswara R Sastry <nasastry@in.ibm.com>
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Suggested-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Tested-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Make pmi_irq_pending() return bool, reflow/reword some comments]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1626846509-1350-2-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 156b5371a9c2482a9ad23ec82d1a4f89a3ab430d ]
This is required in order to allow more significant differences between
NMI type interrupt handlers and regular asynchronous handlers.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210130130852.2952424-20-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91668ab7db4bcfae332e561df1de2401f3f18553 ]
PowerISA v3.1 introduces new control bit (PMCCEXT) for restricting
access to group B PMU registers in problem state when
MMCR0 PMCC=0b00. In problem state and when MMCR0 PMCC=0b00,
setting the Monitor Mode Control Register bit 54 (MMCR0 PMCCEXT),
will restrict read permission on Group B Performance Monitor
Registers (SIER, SIAR, SDAR and MMCR1). When this bit is set to zero,
group B registers will be readable. In other platforms (like power9),
the older behaviour is retained where group B PMU SPRs are readable.
Patch adds support for MMCR0 PMCCEXT bit in power10 by enabling
this bit during boot and during the PMU event enable/disable callback
functions.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606409684-1589-8-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 344fbab991a568dc33ad90711b489d870e18d26d ]
The only thing keeping the cpu_setup() and cpu_restore() functions
used in the cputable entries for Power7, Power8, Power9 and Power10 in
assembly was cpu_restore() being called before there was a stack in
generic_secondary_smp_init(). Commit ("powerpc/64: Set up a kernel
stack for secondaries before cpu_restore()") means that it is now
possible to use C.
Rewrite the functions in C so they are a little bit easier to read.
This is not changing their functionality.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Tweak copyright and authorship notes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201014072837.24539-2-jniethe5@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49bcb1506f2e095262c01bda7fd1c0db524c91e2 ]
When converting the thermal-zones bindings to yaml the definition of the
contribution property changed. The intention is the same, an integer
value expressing a ratio of a sum on how much cooling is provided by the
device to the zone. But after the conversion the integer value is
limited to the range 0 to 100 and expressed as a percentage.
This is problematic for two reasons.
- This do not match how the binding is used. Out of the 18 files that
make use of the property only two (ste-dbx5x0.dtsi and
ste-hrefv60plus.dtsi) sets it at a value that satisfy the binding,
100. The remaining 16 files set the value higher and fail to validate.
- Expressing the value as a percentage instead of a ratio of the sum is
confusing as there is nothing to enforce the sum in the zone is not
greater then 100.
This patch restore the pre yaml conversion description and removes the
value limitation allowing the usage of the bindings to validate.
Fixes: 1202a442a3 ("dt-bindings: thermal: Add yaml bindings for thermal zones")
Reported-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211109103045.1403686-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49f893253ab43566e34332a969324531fea463f6 ]
Commit f37fe2f998 ("ASoC: uniphier: add support for UniPhier AIO common
driver") adds configs SND_SOC_UNIPHIER_{LD11,PXS2}, which select the
non-existing config SND_SOC_UNIPHIER_AIO_DMA.
Hence, ./scripts/checkkconfigsymbols.py warns:
SND_SOC_UNIPHIER_AIO_DMA
Referencing files: sound/soc/uniphier/Kconfig
Probably, there is actually no further config intended to be selected
here. So, just drop selecting the non-existing config.
Fixes: f37fe2f998 ("ASoC: uniphier: add support for UniPhier AIO common driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211125095158.8394-2-lukas.bulwahn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 869fb7e5aecbc163003f93f36dcc26d0554319f6 ]
prom_getprop() can return PROM_ERROR. Binary operator can not identify
it.
Fixes: 94d2dde738 ("[POWERPC] Efika: prune fixups and make them more carefull")
Signed-off-by: Peiwei Hu <jlu.hpw@foxmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/tencent_BA28CC6897B7C95A92EB8C580B5D18589105@qq.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 570727e9acfac1c2330a01dd5e1272e9c3acec08 ]
When attempting to use sys_pll1_80m as the parent for clko1, the
system hangs. This is due to the fact that the source select
for sys_pll1_80m was incorrectly pointing to m7_alt_pll_clk, which
doesn't yet exist.
According to Rev 3 of the TRM, The imx8mn_clko1_sels also incorrectly
references an osc_27m which does not exist, nor does an entry for
source select bits 010b. Fix both by inserting a dummy clock into
the missing space in the table and renaming the incorrectly name clock
with dummy.
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20211117133202.775633-1-aford173@gmail.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 606c54ae975ad3af540b505b46b55a687501711f ]
Starting from commit 05c6c029a4 ("scsi: pm80xx: Increase number of
supported queues") driver initializes only max_q_num queues. Do not use an
invalid queue if the WARN_ON condition is true.
Link: https://lore.kernel.org/r/20211101232825.2350233-4-ipylypiv@google.com
Fixes: 7640e1eb8c5d ("scsi: pm80xx: Make mpi_build_cmd locking consistent")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a67fcfa0db6b4075515bd23497750849b88850f ]
Before query pkey, make sure that the queried index is valid.
Fixes: 9a4435375c ("IB/hns: Add driver files for hns RoCE driver")
Link: https://lore.kernel.org/r/20211117145954.123893-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a917dfb66c0a1fa1caacf3d71edcafcab48e6ff0 ]
The 'cmdq->cmdq_bitmap' bitmap is 'rcfw->cmdq_depth' bits long. The size
stored in 'cmdq->bmap_size' is the size of the bitmap in bytes.
Remove this erroneous 'bmap_size' and use 'rcfw->cmdq_depth' directly in
'bnxt_qplib_disable_rcfw_channel()'. Otherwise some error messages may be
missing.
Other uses of 'cmdq_bitmap' already take into account 'rcfw->cmdq_depth'
directly.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/47ed717c3070a1d0f53e7b4c768a4fd11caf365d.1636707421.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80bd64af75b4bb11c0329bc66c35da2ddfb66d88 ]
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
Fixes: d13bd412dc ("ALSA: hda - Manage kcontrol lists")
Link: https://lore.kernel.org/r/20211116071314.15065-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5471e9762e1af4b7df057a96bfd46cc250979b88 ]
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
Fixes: a8ff48cb70 ("ALSA: pcm: Free chmap at PCM free callback, too")
Link: https://lore.kernel.org/r/20211116071314.15065-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06764dc931848c3a9bc01a63bbf76a605408bb54 ]
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
Fixes: 9058cbe1ee ("ALSA: jack: implement kctl creating for jack devices")
Link: https://lore.kernel.org/r/20211116071314.15065-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 173b6e383d2a204c9921ffc1eca3b87aa2106c33 ]
A user reported FITRIM ioctl failing for him on ext4 on some devices
without apparent reason. After some debugging we've found out that
these devices (being LVM volumes) report rather large discard
granularity of 42MB and the filesystem had 1k blocksize and thus group
size of 8MB. Because ext4 FITRIM implementation puts discard
granularity into minlen, ext4_trim_fs() declared the trim request as
invalid. However just silently doing nothing seems to be a more
appropriate reaction to such combination of parameters since user did
not specify anything wrong.
CC: Lukas Czerner <lczerner@redhat.com>
Fixes: 5c2ed62fd4 ("ext4: Adjust minlen with discard_granularity in the FITRIM ioctl")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20211112152202.26614-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d668769eb9c52b150753f1653f7f5a0aeb8239d2 ]
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com
Fixes: 2a36d70834 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ccdcc8ffd955490feec05380223db6a48961eb5 ]
When building ARCH=arm allmodconfig:
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c: In function ‘iwl_mvm_ftm_rtt_smoothing’:
./include/asm-generic/div64.h:222:35: error: comparison of distinct pointer types lacks a cast [-Werror]
222 | (void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
| ^~
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:1070:9: note: in expansion of macro ‘do_div’
1070 | do_div(rtt_avg, 100);
| ^~~~~~
do_div() has to be used with an unsigned 64-bit integer dividend but
rtt_avg is a signed 64-bit integer.
div_s64() expects a signed 64-bit integer dividend and signed 32-bit
divisor, which fits this scenario, so use that function here to fix the
warning.
Fixes: 8b0f92549f2c ("iwlwifi: mvm: fix 32-bit build in FTM")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211227191757.2354329-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb3485f1f931102d8ba606f1c28123f5b48afa3 ]
We need to set TASK_INTERRUPTIBLE before calling kthread_should_stop().
Otherwise, kthread_stop() might see that the pccardd thread is still
in TASK_RUNNING state and fail to wake it up.
Additionally, we only need to set the state back to TASK_RUNNING if
kthread_should_stop() breaks the loop.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Fixes: d3046ba809 ("pcmcia: fix a boot time warning in pcmcia cs code")
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6564c13dae25cd7f8e1de5127b4da4500ee5844 ]
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Link: https://lore.kernel.org/all/20211224021324.1447494-1-jiasheng@iscas.ac.cn
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 370d988cc529598ebaec6487d4f84c2115dc696b ]
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de
Fixes: 03fd3cf5a1 ("can: add driver for Softing card")
Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
