The mpc836x_mds platform has been broken since the commit
6fe3264945
"netdev/phy: Use mdiobus_read() so that proper locks are taken"
which caused the fsl_pq_mdio TBI autoprobe to oops. The oops
was "fixed" in commit 28d8ea2d56
"fsl_pq_mdio: Clean up tbi address configuration"
by simply removing the the autoscan code, and making tbi nodes
mandatory. Some of the newer reference platforms were updated
to have tbi nodes in 220669495b
"powerpc: Add TBI PHY node to first MDIO bus"
but the older mpc836x didn't get one and hence was just failing
with -EBUSY as follows:
fsl-pq_mdio: probe of e0102120.mdio failed with error -16
...
net eth0: Could not attach to PHY
eth0: Cannot initialize PHY, aborting.
Add a TBI node and use the 1st free address for it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When the P1022's DIU video controller is active, the pixis must be accessed
in "indirect" mode, which uses localbus chip select addresses.
Switching between the DVI and LVDS monitor ports is handled by the pixis,
so that switching needs to be done via indirect mode.
This has the side-effect of no longer requiring U-Boot to enable the DIU.
Now Linux can enable the DIU all by itself.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the GE PIC drivers to allow these to be used by non-86xx boards.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The GE GPIO driver provides basic support (set direction, read/write state)
for the GPIO provided on some GE single board computers. This patch moves
the driver from the 86xx specific platform directrory to the GPIO subsystem
so that it can be used on non-86xx boards.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the GE_FPGA configuration option. This is being carried
out as ground work to allow the PIC and GPIO drivers to be move from the
powerpc 86xx platform directory to more general locations to allow them to
be used on non-86xx boards and to reduce churn when further boards using
these drivers are added.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020RDB-PC Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
10 16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using VitesseTM VSC7385 L2 switch
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1020utm-pc has the similar feature as the p1020rdb.
Therefore, p1020utm-pc use the same platform file as the p1/p2 rdb board.
Overview of P1020UTM-PC platform:
- DDR3 1GB
- NOR flash 32MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY Atheros AR8021)
- eTSEC2 (SGMII PHY Vitesse VSC8221)
- eTSEC3 (RGMII PHY Atheros AR8021)
- SDHC
- 2 USB ports
- PCIe (Lane1 to dual SATA controller)
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1020mbg-pc has the similar feature as the p1020rdb.
Therefore, p1020mbg-pc use the same platform file as the p1/p2 rdb board.
Overview of P1020MBG-PC platform:
- DDR3 2GB
- NOR flash 64MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY) connected to VSC7385 L2 switch
- eTSEC2 (SGMII PHY)
- eTSEC3 (RGMII PHY)
- SDHC
- 2 USB ports
- 4 TDM ports
- PCIe (Lane1 to dual SATA controller)
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NOR flash, need to be disabled.
This also means that the localbus is not a 'simple-bus' any more, so remove
that string from the compatible node.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Create a 32-bit address space version of p1022ds.dts. To avoid confusion,
p1022ds.dts is renamed to p1022ds_36b.dts. We also create p1022ds.dtsi
to store some common nodes.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The properties indicates that the hardware supports waking up via magic
packet.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix typo introduced by "powerpc: Add TBI PHY node to first MDIO bus"
from Andy Fleming.
It's device_type rather than device-type, which causes the mdio probe to
fail thus making all gianfar ethernet interfaces unusable.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is here most likely since the FSL bsp. Back in the FSL bsp it was
set to 50Mhz and working. However the driver divided the SoC freq. only
by 2. According to the TRM the platform clock (which the manual refers
in its formula) is the system clock divided by two. So in the end it has
to divide by 4 and this is what the fsl-spi driver in tree is doing.
Since then the flash is not wokring I guess. After chaning the freq from
50Mhz to 40Mhz like others do then I can access the flash.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is not at 0xffa00000. According to current u-boot source the NAND
controller is always at 0xff800000 and it is either at CS0 or CS1
depending on NAND or NAND+NOR mode. In 36bit mode it is shifted to
0xfff800000 but it has always an eight there and never an A.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the file "arch/powerpc/sysdev/fsl_rmu.c", there will be some compile
errors while using the corenet64_smp_defconfig:
.../fsl_rmu.c:315: error: cast from pointer to integer of different size
.../fsl_rmu.c:320: error: cast to pointer from integer of different size
.../fsl_rmu.c:320: error: cast to pointer from integer of different size
.../fsl_rmu.c:320: error: cast to pointer from integer of different size
.../fsl_rmu.c:330: error: cast to pointer from integer of different size
.../fsl_rmu.c:332: error: cast to pointer from integer of different size
.../fsl_rmu.c:339: error: cast to pointer from integer of different size
.../fsl_rmu.c:340: error: cast to pointer from integer of different size
.../fsl_rmu.c:341: error: cast to pointer from integer of different size
.../fsl_rmu.c:348: error: cast to pointer from integer of different size
.../fsl_rmu.c:348: error: cast to pointer from integer of different size
.../fsl_rmu.c:348: error: cast to pointer from integer of different size
.../fsl_rmu.c:659: error: cast from pointer to integer of different size
.../fsl_rmu.c:659: error: format '%8.8x' expects type 'unsigned int',
but argument 5 has type 'size_t'
.../fsl_rmu.c:985: error: cast from pointer to integer of different size
.../fsl_rmu.c:997: error: cast to pointer from integer of different size
Rewrote the corresponding code with the support of 64bit building.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the file "arch/powerpc/sysdev/fsl_rio.c", there will be some relocation
errors while using the corenet64_smp_defconfig:
WARNING: modpost: Found 6 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
GEN .version
CHK include/generated/compile.h
UPD include/generated/compile.h
CC init/version.o
LD init/built-in.o
LD .tmp_vmlinux1
arch/powerpc/sysdev/built-in.o:(__ex_table+0x0):
relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3208
arch/powerpc/sysdev/built-in.o:(__ex_table+0x2):
relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'
arch/powerpc/sysdev/built-in.o:(__ex_table+0x4):
relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3230
arch/powerpc/sysdev/built-in.o:(__ex_table+0x6):
relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'+c
arch/powerpc/sysdev/built-in.o:(__ex_table+0x8):
relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3250
arch/powerpc/sysdev/built-in.o:(__ex_table+0xa):
relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'+18
Rewrote the corresponding code with the support of 64bit building.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1025RDB Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add usb controller version info for the following:
MPC8536, P1010, P1020, P1021, P1022, P1023, P2020, P2041,
P3041, P3060, P5020
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2020RDB-PC Board shares the same design(PCB) as P102x RDB style platforms.
The difference between this platform and the already existing P2020RDB
is mainly with respect to DDR. The P2020RDB-PC has a DDR3 memory.
The P2020RDB-PC also has a CPLD device connected to local bus.
The main differences from the P102x RDB-PC is 64-bit DDR and SYSCLK of
100Mhz.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021RDB-PC Overview
-----------------
1Gbyte DDR3 (on board DDR)
16Mbyte NOR flash
32Mbyte eSLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
Real-time clock on I2C bus
SD/MMC connector to interface with the SD memory card
PCIex
- x1 PCIe slot or x1 PCIe to dual SATA controller
- x1 mini-PCIe slot
USB 2.0
- ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic’s GL850A
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
eTSEC1: Connected to RGMII PHY VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
in commit 7230c56441
"powerpc: Rework lazy-interrupt handling"
I introduced a regression, accidentally calling irq tracing twice
and not properly restoring a clobbered register (r7) later used
for writing to the MSR.
This caused lockups when booting on a G5 with lockdep enabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using the "compat" APIs, architectures will generally want to
be able to make direct syscalls to msgsnd(), shmctl(), etc., and
in the kernel we would want them to be handled directly by
compat_sys_xxx() functions, as is true for other compat syscalls.
However, for historical reasons, several of the existing compat IPC
syscalls do not do this. semctl() expects a pointer to the fourth
argument, instead of the fourth argument itself. msgsnd(), msgrcv()
and shmat() expect arguments in different order.
This change adds an ARCH_WANT_OLD_COMPAT_IPC config option that can be
set to preserve this behavior for ports that use it (x86, sparc, powerpc,
s390, and mips). No actual semantics are changed for those architectures,
and there is only a minimal amount of code refactoring in ipc/compat.c.
Newer architectures like tile (and perhaps future architectures such
as arm64 and unicore64) should not select this option, and thus can
avoid having any IPC-specific code at all in their architecture-specific
compat layer. In the same vein, if this option is not selected, IPC_64
mode is assumed, since that's what the <asm-generic> headers expect.
The workaround code in "tile" for msgsnd() and msgrcv() is removed
with this change; it also fixes the bug that shmat() and semctl() were
not being properly handled.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The registers that describe size supported by TLB are different on MMU
v2 as well as we support power of two page sizes. For now we continue
to assume that FSL variable size array supports all page sizes up to the
maximum one reported in TLB1PS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The SERIAL_8250_EXTENDED option just enables access to other
less regularly used options, like SERIAL_8250_SHARE_IRQ.
Select it to get rid of this warning when selecting the child
option living underneath it.
warning: (FSL_SOC_BOOKE && SERIAL_8250_RM9K) selects
SERIAL_8250_SHARE_IRQ which has unmet direct dependencies
(HAS_IOMEM && SERIAL_8250_EXTENDED)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current implementation of lazy interrupts handling has some
issues that this tries to address.
We don't do the various workarounds we need to do when re-enabling
interrupts in some cases such as when returning from an interrupt
and thus we may still lose or get delayed decrementer or doorbell
interrupts.
The current scheme also makes it much harder to handle the external
"edge" interrupts provided by some BookE processors when using the
EPR facility (External Proxy) and the Freescale Hypervisor.
Additionally, we tend to keep interrupts hard disabled in a number
of cases, such as decrementer interrupts, external interrupts, or
when a masked decrementer interrupt is pending. This is sub-optimal.
This is an attempt at fixing it all in one go by reworking the way
we do the lazy interrupt disabling from the ground up.
The base idea is to replace the "hard_enabled" field with a
"irq_happened" field in which we store a bit mask of what interrupt
occurred while soft-disabled.
When re-enabling, either via arch_local_irq_restore() or when returning
from an interrupt, we can now decide what to do by testing bits in that
field.
We then implement replaying of the missed interrupts either by
re-using the existing exception frame (in exception exit case) or via
the creation of a new one from an assembly trampoline (in the
arch_local_irq_enable case).
This removes the need to play with the decrementer to try to create
fake interrupts, among others.
In addition, this adds a few refinements:
- We no longer hard disable decrementer interrupts that occur
while soft-disabled. We now simply bump the decrementer back to max
(on BookS) or leave it stopped (on BookE) and continue with hard interrupts
enabled, which means that we'll potentially get better sample quality from
performance monitor interrupts.
- Timer, decrementer and doorbell interrupts now hard-enable
shortly after removing the source of the interrupt, which means
they no longer run entirely hard disabled. Again, this will improve
perf sample quality.
- On Book3E 64-bit, we now make the performance monitor interrupt
act as an NMI like Book3S (the necessary C code for that to work
appear to already be present in the FSL perf code, notably calling
nmi_enter instead of irq_enter). (This also fixes a bug where BookE
perfmon interrupts could clobber r14 ... oops)
- We could make "masked" decrementer interrupts act as NMIs when doing
timer-based perf sampling to improve the sample quality.
Signed-off-by-yet: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2:
- Add hard-enable to decrementer, timer and doorbells
- Fix CR clobber in masked irq handling on BookE
- Make embedded perf interrupt act as an NMI
- Add a PACA_HAPPENED_EE_EDGE for use by FSL if they want
to retrigger an interrupt without preventing hard-enable
v3:
- Fix or vs. ori bug on Book3E
- Fix enabling of interrupts for some exceptions on Book3E
v4:
- Fix resend of doorbells on return from interrupt on Book3E
v5:
- Rebased on top of my latest series, which involves some significant
rework of some aspects of the patch.
v6:
- 32-bit compile fix
- more compile fixes with various .config combos
- factor out the asm code to soft-disable interrupts
- remove the C wrapper around preempt_schedule_irq
v7:
- Fix a bug with hard irq state tracking on native power7
With the original EEH implementation, the access to config space of
the corresponding PCI device is done by RTAS sensitive function. That
depends on pci_dn heavily. That would limit EEH extension to other
platforms like powernv because other platforms might have different
ways to access PCI config space.
The patch splits those functions used to access PCI config space
and implement them in platform related EEH component. It would be
helpful to support EEH on multiple platforms simutaneously in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the original EEH implementation, the EEH global statistics
are maintained by individual global variables. That makes the
code a little hard to maintain.
The patch introduces extra struct eeh_stats for the EEH global
statistics so that it can be maintained in collective fashion.
It's the rework on the corresponding v5 patch. According to
the comments from David Laight, the EEH global statistics have
been changed for a litte bit so that they have fixed-type of
"u64". Also, the format used to print them has been changed to
"%llu" based on David's suggestion. Also, the output format of
EEH global statistics should be kept as intacted according to
Michael's suggestion that there might be tools parsing them.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pci_dn has been replaced with eeh_dev. In order to comply with
the rule, the EEH platform implementation on pSeries should also
be adjusted for a little bit so that it will depend on eeh_dev instead
of pci_dn.
The patch replaces pci_dn with eeh_dev. The corresponding information
will be retrieved from eeh_dev instead of pci_dn.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The original EEH implementation is heavily depending on struct pci_dn.
We have to put EEH related information to pci_dn. Actually, we could
split struct pci_dn so that the EEH sensitive information to form an
individual struct, then EEH looks more independent.
The patch replaces pci_dn with eeh_dev for EEH aux components like
event and driver. Also, the eeh_event struct has been adjusted for
a little bit since eeh_dev has linked the associated FDT (Flat Device
Tree) node and PCI device. It's not necessary for eeh_event struct to
trace FDT node and PCI device. We can just simply to trace eeh_dev in
eeh_event.
The patch also renames function pcid_name() to eeh_pcid_name(), which
should be missed in the previous patch where the EEH aux components
have been cleaned up.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The original EEH implementation is heavily depending on struct pci_dn.
We have to put EEH related information to pci_dn. Actually, we could
split struct pci_dn so that the EEH sensitive information to form an
individual struct, then EEH looks more independent.
The patch replaces pci_dn with eeh_dev for EEH core.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With original EEH implementation, struct pci_dn is used while building
PCI I/O address cache, which helps on searching the corresponding
PCI device according to the given physical I/O address. Besides, pci_dn
is associated with the corresponding PCI device while building its
I/O cache.
The patch replaces struct pci_dn with struct eeh_dev so that EEH address
cache won't depend on struct pci_dn. That will help EEH to become an
independent module in future. Besides, the binding of eeh_dev and PCI
device is done while building PCI device I/O cache.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With original EEH implementation, all EEH related statistics have
been put into struct pci_dn. We've introduced struct eeh_dev to
replace struct pci_dn in EEH core components, including EEH sysfs
component.
The patch shows EEH statistics from struct eeh_dev instead of struct
pci_dn in EEH sysfs component. Besides, it also fixed the EEH device
retrieval from PCI device, which was introduced by the previous patch
in the series of patch.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Original EEH implementation depends on struct pci_dn heavily. However,
EEH shouldn't depend on that actually because EEH needn't share much
information with other PCI components. That's to say, EEH should have
worked independently.
The patch introduces struct eeh_dev so that EEH core components needn't
be working based on struct pci_dn in future. Also, struct pci_dn, struct
eeh_dev instances are created in dynamic fasion and the binding with EEH
device, OF node, PCI device is implemented as well.
The EEH devices are created after PHBs are detected and initialized, but
PCI emunation hasn't started yet. Apart from that, PHB might be created
dynamically through DLPAR component and the EEH devices should be creatd
as well. Another case might be OF node is created dynamically by DR
(Dynamic Reconfiguration), which has been defined by PAPR. For those OF
nodes created by DR, EEH devices should be also created accordingly. The
binding between EEH device and OF node is done while the EEH device is
initially created.
The binding between EEH device and PCI device should be done after PCI
emunation is done. Besides, PCI hotplug also needs the binding so that
the EEH devices could be traced from the newly coming PCI buses or PCI
devices.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch does some cleanup on the function names of EEH
aux components. Currently, only couple of function names from
eeh_cache have been adjusted so that:
* The function name has prefix "eeh_addr_cache".
* Move around pci_addr_cache_build() in the header file
to reflect function call sequence.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're several EEH aux components and the patch does some cleanup
for them so that they look more clean.
* Duplicated comments have been removed from the header file.
* Comments have been reorganized so that it looks more clean.
* The leading comments of functions are adjusted for a little
bit so that the result of "make pdfdocs" would be more
unified.
* Function calls "xxx ()" has been replaced by "xxx()".
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In order to enable particular PCI device, which has been included
in the parent PE. The involved PCI bridges should be enabled explicitly
if there has. On pSeries platform, there're dedicated RTAS calls
to fulfil the purpose.
The patch implements the function of configuring PCI bridges through
the dedicated RTAS calls. Besides, the function has been abstracted
by struct eeh_ops::configure_bridge so that the EEH core components
could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On RTAS compliant pSeries platform, one dedicated RTAS call has
been introduced to retrieve EEH temporary or permanent error log.
The patch implements the function of retriving EEH error log through
RTAS call. Besides, it has been abstracted by struct eeh_ops::get_log
so that EEH core components could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On RTAS compliant pSeries platform, there is a dedicated RTAS call
(ibm,set-slot-reset) to reset the specified PE. Furthermore, two
types of resets are supported: hot and fundamental. the type of
reset is to be used actually depends on the included PCI device's
requirements.
The patch implements resetting PE on pSeries platform through RTAS
call. Besides, it has been abstracted through struct eeh_ops::reset
so that EEH core components could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On pSeries platform, the PE state might be temporarily unavailable.
In that case, the firmware will return the corresponding wait time.
That means the kernel has to wait for appropriate time in order to
get the PE state.
The patch does the implementation for that. Besides, the function
has been abstracted through struct eeh_ops::wait_state so that EEH core
components could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On pSeries platform, there're 2 dedicated RTAS calls introduced to
retrieve the corresponding PE's state: ibm,read-slot-reset-state and
ibm,read-slot-reset-state2.
The patch implements the retrieval of PE's state according to the
given PE address. Besides, the implementation has been abstracted by
struct eeh_ops::get_state so that EEH core components could support
multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 types of addresses used for EEH operations. The first
one would be BDF (Bus/Device/Function) address which is retrieved
from the reg property of the corresponding FDT node. Another one
is PE address that should be enquired from firmware through RTAS
call on pSeries platform. When issuing EEH operation, the PE address
has precedence over BDF address.
The patch implements retrieving PE address according to the given
BDF address on pSeries platform. Also, the struct eeh_early_enable_info
has been removed since the information can be figured out from
dn->pdn->phb->buid directly and that simplifies the code.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 4 EEH operations that are covered by the dedicated RTAS
call <ibm,set-eeh-option>: enable or disable EEH, enable MMIO and
enable DMA. At early stage of system boot, the EEH would be tried
to enable on PCI device related device node. MMIO and DMA for
particular PE should be enabled when doing recovery on EEH errors
so that the PE could function properly again.
The patch implements it and abstract that through struct
eeh_ops::set_eeh. It would be help for EEH to support multiple
platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The platform specific EEH operations have been abstracted by
struct eeh_ops. The individual platroms, including pSeries, needs
doing necessary initialization before the platform dependent EEH
operations work properly.
The patch is addressing that and do necessary platform initialization
for pSeries platform. More specificly, it will figure out the tokens
of EEH related RTAS calls.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
EEH has been implemented on RTAS-compliant pSeries platform.
That's to say, the EEH operations will be implemented through RTAS
calls eventually. The situation limited feasible extension on EEH.
In order to support EEH on multiple platforms like pseries and powernv
simutaneously. We have to split the platform dependent EEH options
up out of current implementation.
The patch addresses supporting EEH on multiple platforms. The pseries
platform dependent EEH operations will be abstracted by struct eeh_ops.
EEH core components will be built based on the registered EEH operations.
With the mechanism, what the individual platform needs to do is implement
platform dependent EEH operations.
For now, the pseries platform is covered under the mechanism. That means
we have to think about other platforms to support EEH, like powernv.
Besides, we only have framework for the mechanism and we have to implement
it for pseries platform later.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH has been implemented on pSeries platform. The original
code looks a little bit nasty. The patch does cleanup on the
current EEH implementation so that it looks more clean.
* Try adding prefix "eeh" for functions.
* Some function names have been adjusted so that they looks
shorter and meaningful.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH has been implemented on pSeries platform. The original
code looks a little bit nasty. The patch does cleanup on the
current EEH implementation so that it looks more clean.
* Duplicated comments have been removed from the corresponding
header files.
* Comments have been reorganized so that it looks more clean.
* The leading comments of functions are adjusted for a little
bit so that the result of "make pdfdocs" would be more
unified.
* Function definitions and calls have unified format as "xxx()".
That means the format "xxx ()" has been replaced by "xxx()".
* There're multiple functions implemented for resetting PE. The
position of those functions have been move around so that they
are adjacent to each other to reflect their relationship.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 64-bit, the mfmsr instruction can be quite slow, slower
than loading a field from the cache-hot PACA, which happens
to already contain the value we want in most cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We were using CR0.EQ after EXCEPTION_COMMON, hoping it still
contained whether we came from userspace or kernel space.
However, under some circumstances, EXCEPTION_COMMON will
call C code and clobber non-volatile registers, so we really
need to re-load the previous MSR from the stackframe and
re-test.
While there, invert the condition to make the fast path more
obvious and remove the BUG_OPCODE which was a debugging
leftover and call .ret_from_except as we should.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running under a hypervisor that supports stolen time accounting,
we may call C code from the macro EXCEPTION_PROLOG_COMMON in the
exception entry path, which clobbers CR0.
However, the FPU and vector traps rely on CR0 indicating whether we
are coming from userspace or kernel to decide what to do.
So we need to restore that value after the C call
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Also use local_paca instead of get_paca() to avoid getting into
the smp_processor_id() debugging code from the debugger
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Other architectures such as x86 and ARM have been growing
new support for features like retrying page faults after
dropping the mm semaphore to break contention, or being
able to return from a stuck page fault when a SIGKILL is
pending.
This refactors our implementation of do_page_fault() to
move the error handling out of line in a way similar to
x86 and adds support for those two features.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we get a floating point, altivec or vsx unavaible interrupt in
kernel, we trigger a kernel error. There is no point preserving
the interrupt state, in fact, that can even make debugging harder
as the processor state might change (we may even preempt) between
taking the exception and landing in a debugger.
So just make those 3 disable interrupts unconditionally.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2: On BookE only disable when hitting the kernel unavailable
path, otherwise it will fail to restore softe as
fast_exception_return doesn't do it.
We currently turn interrupts back to their previous state before
calling do_page_fault(). This can be annoying when debugging as
a bad fault will potentially have lost some processor state before
getting into the debugger.
We also end up calling some generic code with interrupts enabled
such as notify_page_fault() with interrupts enabled, which could
be unexpected.
This changes our code to behave more like other architectures,
and make the assembly entry code call into do_page_faults() with
interrupts disabled. They are conditionally re-enabled from
within do_page_fault() in the same spot x86 does it.
While there, add the might_sleep() test in the case of a successful
trylock of the mmap semaphore, again like x86.
Also fix a bug in the existing assembly where r12 (_MSR) could get
clobbered by C calls (the DTL accounting in the exception common
macro and DISABLE_INTS) in some cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2. Add the r12 clobber fix
Some exceptions would unconditionally disable interrupts on entry,
which is fine, but calling lockdep every time not only adds more
overhead than strictly needed, but also means we get quite a few
"redudant" disable logged, which makes it hard to spot the really
bad ones.
So instead, split the macro used by the exception code into a
normal one and a separate one used when CONFIG_TRACE_IRQFLAGS is
enabled, and make the later skip th tracing if interrupts were
already disabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We unconditionally hard enable interrupts. This is unnecessary as
syscalls are expected to always be called with interrupts enabled.
While at it, we add a WARN_ON if that is not the case and
CONFIG_TRACE_IRQFLAGS is enabled (we don't want to add overhead
to the fast path when this is not set though).
Thus let's remove the enabling (and associated irq tracing) from
the syscall entry path. Also on Book3S, replace a few mfmsr
instructions with loads of PACAMSR from the PACA, which should be
faster & schedule better.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves the inlines into system.h and changes the runlatch
code to use the thread local flags (non-atomic) rather than
the TIF flags (atomic) to keep track of the latch state.
The code to turn it back on in an asynchronous interrupt is
now simplified and partially inlined.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The perfmon interrupt is the sole user of a special variant of the
interrupt prolog which differs from the one used by external and timer
interrupts in that it saves the non-volatile GPRs and doesn't turn the
runlatch on.
The former is unnecessary and the later is arguably incorrect, so
let's clean that up by using the same prolog. While at it we rename
that prolog to use the _ASYNC prefix.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes the various bits of assembly in the kernel entry,
exception handling and SLB management code that were specific
to running under the legacy iSeries hypervisor which is no
longer supported.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This cleans up vio.c after the removal of the legacy iSeries platform.
It also removes some no longer referenced include files.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/kvm/book3s_hv.c: included 'linux/sched.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some members of kvm_memory_slot are not used by every architecture.
This patch is the first step to make this difference clear by
introducing kvm_memory_slot::arch; lpage_info is moved into it.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
- Use memchr_inv to check if the data contains all 0xFF bytes.
It is faster than looping for each byte.
- Use memcmp to compare memory areas
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All IRQs on powerpc are managed via irq_domain anyway, there isn't really
any advantage to turning SPARSE_IRQ off, and it's the direction we want
to take the kernel design anyway. This patch makes powerpc always use
SPARSE_IRQ.
On pseries_defconfig, SPARSE_IRQ adds only about 0x300 bytes to the
.text sections, and removes about 0x20000 from the data section for the
static irq_desc table.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On a 16TB system (using AMS/CMO), I get:
WARNING: ignoring large property [/ibm,dynamic-reconfiguration-memory] ibm,dynamic-memory length 0x000000000017ffec
and significantly less memory is thus shown to the partition. As far as
I can tell, the constant used is arbitrary. Ben Herrenschmidt provided
additional background that
> The limit was originally set because of Apple machines carrying ROM
> images in the device-tree, at a time where we were much more memory
> constrained than we are now.
and that it is likely not very useful any longer.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Emit the function name not the address when possible.
builtin_return_address() gives an address. When building
a kernel with CONFIG_KALLSYMS, emit the actual function
name not the address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is a race where a thread causes a coprocessor type to be valid
in its own ACOP _and_ in the current context, but it does not
propagate to the ACOP register of other threads in time for them to
use it. The original code tries to solve this by sending an IPI to
all threads on the system, which is heavy handed, but unfortunately
still provides a window where the icswx is issued by other threads and
the ACOP is not up to date.
This patch detects that the ACOP DSI fault was a "false positive" and
syncs the ACOP and causes the icswx to be replayed.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement atomic_inc_not_zero and atomic64_inc_not_zero. At the
moment we use atomic*_add_unless which requires us to put 0 and
1 constants into registers. We can also avoid a subtract by
saving the original value in a second temporary.
This removes 3 instructions from fget:
- c0000000001b63c0: 39 00 00 00 li r8,0
- c0000000001b63c4: 39 40 00 01 li r10,1
...
- c0000000001b63e8: 7c 0a 00 50 subf r0,r10,r0
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This compatible value will be used to distinguish some special features of APM821XX EMAC: no half duplex mode support, configuring jumbo frame.
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're currently allocating 16MB of linear memory on demand when creating
a guest. That does work some times, but finding 16MB of linear memory
available in the system at runtime is definitely not a given.
So let's add another command line option similar to the RMA preallocator,
that we can use to keep a pool of page tables around. Now, when a guest
gets created it has a pretty low chance of receiving an OOM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
RMAs and HPT preallocated spaces should be zeroed, so we don't accidently
leak information from previous VM executions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
We have code to allocate big chunks of linear memory on bootup for later use.
This code is currently used for RMA allocation, but can be useful beyond that
extent.
Make it generic so we can reuse it for other stuff later.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
This moves __gfn_to_memslot() and search_memslots() from kvm_main.c to
kvm_host.h to reduce the code duplication caused by the need for
non-modular code in arch/powerpc/kvm/book3s_hv_rm_mmu.c to call
gfn_to_memslot() in real mode.
Rather than putting gfn_to_memslot() itself in a header, which would
lead to increased code size, this puts __gfn_to_memslot() in a header.
Then, the non-modular uses of gfn_to_memslot() are changed to call
__gfn_to_memslot() instead. This way there is only one place in the
source code that needs to be changed should the gfn_to_memslot()
implementation need to be modified.
On powerpc, the Book3S HV style of KVM has code that is called from
real mode which needs to call gfn_to_memslot() and thus needs this.
(Module code is allocated in the vmalloc region, which can't be
accessed in real mode.)
With this, we can remove builtin_gfn_to_memslot() from book3s_hv_rm_mmu.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of keeping separate copies of struct kvm_vcpu_arch_shared (one in
the code, one in the docs) that inevitably fail to be kept in sync
(already sr[] is missing from the doc version), just point to the header
file as the source of documentation on the contents of the magic page.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We need the KVM_REG namespace for generic register settings now, so
let's rename the existing users to something different, enabling
us to reuse the namespace for more visible interfaces.
While at it, also move these private constants to a private header.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This moves the get/set_one_reg implementation down from powerpc.c into
booke.c, book3s_pr.c and book3s_hv.c. This avoids #ifdefs in C code,
but more importantly, it fixes a bug on Book3s HV where we were
accessing beyond the end of the kvm_vcpu struct (via the to_book3s()
macro) and corrupting memory, causing random crashes and file corruption.
On Book3s HV we only accept setting the HIOR to zero, since the guest
runs in supervisor mode and its vectors are never offset from zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf update to apply on top of changed ONE_REG patches]
Signed-off-by: Avi Kivity <avi@redhat.com>
Until now, we always set HIOR based on the PVR, but this is just wrong.
Instead, we should be setting HIOR explicitly, so user space can decide
what the initial HIOR value is - just like on real hardware.
We keep the old PVR based way around for backwards compatibility, but
once user space uses the SET_ONE_REG based method, we drop the PVR logic.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Right now we transfer a static struct every time we want to get or set
registers. Unfortunately, over time we realize that there are more of
these than we thought of before and the extensibility and flexibility of
transferring a full struct every time is limited.
So this is a new approach to the problem. With these new ioctls, we can
get and set a single register that is identified by an ID. This allows for
very precise and limited transmittal of data. When we later realize that
it's a better idea to shove over multiple registers at once, we can reuse
most of the infrastructure and simply implement a GET_MANY_REGS / SET_MANY_REGS
interface.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently the code kzalloc()s new VCPUs instead of using the kmem_cache
which is created when KVM is initialized.
Modify it to allocate VCPUs from that kmem_cache.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The existing kvm_stlb_write/kvm_gtlb_write were a poor match for
the e500/book3e MMU -- mas1 was passed as "tid", mas2 was limited
to "unsigned int" which will be a problem on 64-bit, mas3/7 got
split up rather than treated as a single 64-bit word, etc.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
[scottwood@freescale.com: made mas2 64-bit, and added mas8 init]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This changes the implementation of kvm_vm_ioctl_get_dirty_log() for
Book3s HV guests to use the hardware C (changed) bits in the guest
hashed page table. Since this makes the implementation quite different
from the Book3s PR case, this moves the existing implementation from
book3s.c to book3s_pr.c and creates a new implementation in book3s_hv.c.
That implementation calls kvmppc_hv_get_dirty_log() to do the actual
work by calling kvm_test_clear_dirty on each page. It iterates over
the HPTEs, clearing the C bit if set, and returns 1 if any C bit was
set (including the saved C bit in the rmap entry).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This uses the host view of the hardware R (referenced) bit to speed
up kvm_age_hva() and kvm_test_age_hva(). Instead of removing all
the relevant HPTEs in kvm_age_hva(), we now just reset their R bits
if set. Also, kvm_test_age_hva() now scans the relevant HPTEs to
see if any of them have R set.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allows both the guest and the host to use the referenced (R) and
changed (C) bits in the guest hashed page table. The guest has a view
of R and C that is maintained in the guest_rpte field of the revmap
entry for the HPTE, and the host has a view that is maintained in the
rmap entry for the associated gfn.
Both view are updated from the guest HPT. If a bit (R or C) is zero
in either view, it will be initially set to zero in the HPTE (or HPTEs),
until set to 1 by hardware. When an HPTE is removed for any reason,
the R and C bits from the HPTE are ORed into both views. We have to
be careful to read the R and C bits from the HPTE after invalidating
it, but before unlocking it, in case of any late updates by the hardware.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This reworks the implementations of the H_REMOVE and H_BULK_REMOVE
hcalls to make sure that we keep the HPTE locked and in the reverse-
mapping chain until we have finished invalidating it. Previously
we would remove it from the chain and unlock it before invalidating
it, leaving a tiny window when the guest could access the page even
though we believe we have removed it from the guest (e.g.,
kvm_unmap_hva() has been called for the page and has found no HPTEs
in the chain). In addition, we'll need this for future patches where
we will need to read the R and C bits in the HPTE after invalidating
it.
Doing this required restructuring kvmppc_h_bulk_remove() substantially.
Since we want to batch up the tlbies, we now need to keep several
HPTEs locked simultaneously. In order to avoid possible deadlocks,
we don't spin on the HPTE bitlock for any except the first HPTE in
a batch. If we can't acquire the HPTE bitlock for the second or
subsequent HPTE, we terminate the batch at that point, do the tlbies
that we have accumulated so far, unlock those HPTEs, and then start
a new batch to do the remaining invalidations.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
PPC KVM lacks these two capabilities, and as such a userland system must assume
a max of 4 VCPUs (following api.txt). With these, a userland can determine
a more realistic limit.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix usage of vcpu struct before check that it's actually valid.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
With this, if a guest does an H_ENTER with a read/write HPTE on a page
which is currently read-only, we make the actual HPTE inserted be a
read-only version of the HPTE. We now intercept protection faults as
well as HPTE not found faults, and for a protection fault we work out
whether it should be reflected to the guest (e.g. because the guest HPTE
didn't allow write access to usermode) or handled by switching to
kernel context and calling kvmppc_book3s_hv_page_fault, which will then
request write access to the page and update the actual HPTE.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds the infrastructure to enable us to page out pages underneath
a Book3S HV guest, on processors that support virtualized partition
memory, that is, POWER7. Instead of pinning all the guest's pages,
we now look in the host userspace Linux page tables to find the
mapping for a given guest page. Then, if the userspace Linux PTE
gets invalidated, kvm_unmap_hva() gets called for that address, and
we replace all the guest HPTEs that refer to that page with absent
HPTEs, i.e. ones with the valid bit clear and the HPTE_V_ABSENT bit
set, which will cause an HDSI when the guest tries to access them.
Finally, the page fault handler is extended to reinstantiate the
guest HPTE when the guest tries to access a page which has been paged
out.
Since we can't intercept the guest DSI and ISI interrupts on PPC970,
we still have to pin all the guest pages on PPC970. We have a new flag,
kvm->arch.using_mmu_notifiers, that indicates whether we can page
guest pages out. If it is not set, the MMU notifier callbacks do
nothing and everything operates as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This provides the low-level support for MMIO emulation in Book3S HV
guests. When the guest tries to map a page which is not covered by
any memslot, that page is taken to be an MMIO emulation page. Instead
of inserting a valid HPTE, we insert an HPTE that has the valid bit
clear but another hypervisor software-use bit set, which we call
HPTE_V_ABSENT, to indicate that this is an absent page. An
absent page is treated much like a valid page as far as guest hcalls
(H_ENTER, H_REMOVE, H_READ etc.) are concerned, except of course that
an absent HPTE doesn't need to be invalidated with tlbie since it
was never valid as far as the hardware is concerned.
When the guest accesses a page for which there is an absent HPTE, it
will take a hypervisor data storage interrupt (HDSI) since we now set
the VPM1 bit in the LPCR. Our HDSI handler for HPTE-not-present faults
looks up the hash table and if it finds an absent HPTE mapping the
requested virtual address, will switch to kernel mode and handle the
fault in kvmppc_book3s_hv_page_fault(), which at present just calls
kvmppc_hv_emulate_mmio() to set up the MMIO emulation.
This is based on an earlier patch by Benjamin Herrenschmidt, but since
heavily reworked.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This expands the reverse mapping array to contain two links for each
HPTE which are used to link together HPTEs that correspond to the
same guest logical page. Each circular list of HPTEs is pointed to
by the rmap array entry for the guest logical page, pointed to by
the relevant memslot. Links are 32-bit HPT entry indexes rather than
full 64-bit pointers, to save space. We use 3 of the remaining 32
bits in the rmap array entries as a lock bit, a referenced bit and
a present bit (the present bit is needed since HPTE index 0 is valid).
The bit lock for the rmap chain nests inside the HPTE lock bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This provides for the case where userspace maps an I/O device into the
address range of a memory slot using a VM_PFNMAP mapping. In that
case, we work out the pfn from vma->vm_pgoff, and record the cache
enable bits from vma->vm_page_prot in two low-order bits in the
slot_phys array entries. Then, in kvmppc_h_enter() we check that the
cache bits in the HPTE that the guest wants to insert match the cache
bits in the slot_phys array entry. However, we do allow the guest to
create what it thinks is a non-cacheable or write-through mapping to
memory that is actually cacheable, so that we can use normal system
memory as part of an emulated device later on. In that case the actual
HPTE we insert is a cacheable HPTE.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This relaxes the requirement that the guest memory be provided as
16MB huge pages, allowing it to be provided as normal memory, i.e.
in pages of PAGE_SIZE bytes (4k or 64k). To allow this, we index
the kvm->arch.slot_phys[] arrays with a small page index, even if
huge pages are being used, and use the low-order 5 bits of each
entry to store the order of the enclosing page with respect to
normal pages, i.e. log_2(enclosing_page_size / PAGE_SIZE).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This removes the code from kvmppc_core_prepare_memory_region() that
looked up the VMA for the region being added and called hva_to_page
to get the pfns for the memory. We have no guarantee that there will
be anything mapped there at the time of the KVM_SET_USER_MEMORY_REGION
ioctl call; userspace can do that ioctl and then map memory into the
region later.
Instead we defer looking up the pfn for each memory page until it is
needed, which generally means when the guest does an H_ENTER hcall on
the page. Since we can't call get_user_pages in real mode, if we don't
already have the pfn for the page, kvmppc_h_enter() will return
H_TOO_HARD and we then call kvmppc_virtmode_h_enter() once we get back
to kernel context. That calls kvmppc_get_guest_page() to get the pfn
for the page, and then calls back to kvmppc_h_enter() to redo the HPTE
insertion.
When the first vcpu starts executing, we need to have the RMO or VRMA
region mapped so that the guest's real mode accesses will work. Thus
we now have a check in kvmppc_vcpu_run() to see if the RMO/VRMA is set
up and if not, call kvmppc_hv_setup_rma(). It checks if the memslot
starting at guest physical 0 now has RMO memory mapped there; if so it
sets it up for the guest, otherwise on POWER7 it sets up the VRMA.
The function that does that, kvmppc_map_vrma, is now a bit simpler,
as it calls kvmppc_virtmode_h_enter instead of creating the HPTE itself.
Since we are now potentially updating entries in the slot_phys[]
arrays from multiple vcpu threads, we now have a spinlock protecting
those updates to ensure that we don't lose track of any references
to pages.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
At present, our implementation of H_ENTER only makes one try at locking
each slot that it looks at, and doesn't even retry the ldarx/stdcx.
atomic update sequence that it uses to attempt to lock the slot. Thus
it can return the H_PTEG_FULL error unnecessarily, particularly when
the H_EXACT flag is set, meaning that the caller wants a specific PTEG
slot.
This improves the situation by making a second pass when no free HPTE
slot is found, where we spin until we succeed in locking each slot in
turn and then check whether it is full while we hold the lock. If the
second pass fails, then we return H_PTEG_FULL.
This also moves lock_hpte to a header file (since later commits in this
series will need to use it from other source files) and renames it to
try_lock_hpte, which is a somewhat less misleading name.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds two new functions, kvmppc_pin_guest_page() and
kvmppc_unpin_guest_page(), and uses them to pin the guest pages where
the guest has registered areas of memory for the hypervisor to update,
(i.e. the per-cpu virtual processor areas, SLB shadow buffers and
dispatch trace logs) and then unpin them when they are no longer
required.
Although it is not strictly necessary to pin the pages at this point,
since all guest pages are already pinned, later commits in this series
will mean that guest pages aren't all pinned.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allocates an array for each memory slot that is added to store
the physical addresses of the pages in the slot. This array is
vmalloc'd and accessed in kvmppc_h_enter using real_vmalloc_addr().
This allows us to remove the ram_pginfo field from the kvm_arch
struct, and removes the 64GB guest RAM limit that we had.
We use the low-order bits of the array entries to store a flag
indicating that we have done get_page on the corresponding page,
and therefore need to call put_page when we are finished with the
page. Currently this is set for all pages except those in our
special RMO regions.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds an array that parallels the guest hashed page table (HPT),
that is, it has one entry per HPTE, used to store the guest's view
of the second doubleword of the corresponding HPTE. The first
doubleword in the HPTE is the same as the guest's idea of it, so we
don't need to store a copy, but the second doubleword in the HPTE has
the real page number rather than the guest's logical page number.
This allows us to remove the back_translate() and reverse_xlate()
functions.
This "reverse mapping" array is vmalloc'd, meaning that to access it
in real mode we have to walk the kernel's page tables explicitly.
That is done by the new real_vmalloc_addr() function. (In fact this
returns an address in the linear mapping, so the result is usable
both in real mode and in virtual mode.)
There are also some minor cleanups here: moving the definitions of
HPT_ORDER etc. to a header file and defining HPT_NPTE for HPT_NPTEG << 3.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When commit f43fdc15fa ("KVM: PPC: booke: Improve timer register
emulation") factored out some code in arch/powerpc/kvm/powerpc.c
into a new helper function, kvm_vcpu_kick(), an error crept in
which causes Book3s HV guest vcpus to stall. This fixes it.
On POWER7 machines, guest vcpus are grouped together into virtual
CPU cores that share a single waitqueue, so it's important to use
vcpu->arch.wqp rather than &vcpu->wq.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we patch the whole code include paravirt template code.
This isn't safe for scratch area and has impact to performance.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The hardware maintains a per-set next victim hint. Using this
reduces conflicts, especially on e500v2 where a single guest
TLB entry is mapped to two shadow TLB entries (user and kernel).
We want those two entries to go to different TLB ways.
sesel is now only used for TLB1.
Reported-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The associativity, not just total size, can differ from the host
hardware.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
As Scott put it:
> If we get a signal after the check, we want to be sure that we don't
> receive the reschedule IPI until after we're in the guest, so that it
> will cause another signal check.
we need to have interrupts disabled from the point we do signal_check()
all the way until we actually enter the guest.
This patch fixes potential signal loss races.
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Our vcpu kick implementation differs a bit from x86 which resulted in us not
disabling preemption during the kick. Get it a bit closer to what x86 does.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When running the 64-bit Book3s PR code without CONFIG_PREEMPT_NONE, we were
doing a few things wrong, most notably access to PACA fields without making
sure that the pointers stay stable accross the access (preempt_disable()).
This patch moves to_svcpu towards a get/put model which allows us to disable
preemption while accessing the shadow vcpu fields in the PACA. That way we
can run preemptible and everyone's happy!
Reported-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Somewhere during merges we ended up from
local_irq_enable()
foo();
local_irq_disable()
to always keeping irqs enabled during that part. However, we now
have the following code:
foo();
local_irq_disable()
which disables interrupts without the surrounding code enabling them
again! So let's remove that disable and be happy.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When entering the guest, we want to make sure we're not getting preempted
away, so let's disable preemption on entry, but enable it again while handling
guest exits.
Reported-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Decrementers are now properly driven by TCR/TSR, and the guest
has full read/write access to these registers.
The decrementer keeps ticking (and setting the TSR bit) regardless of
whether the interrupts are enabled with TCR.
The decrementer stops at zero, rather than going negative.
Decrementers (and FITs, once implemented) are delivered as
level-triggered interrupts -- dequeued when the TSR bit is cleared, not
on delivery.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
[scottwood@freescale.com: significant changes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allows additional registers to be accessed by the guest
in PR-mode KVM without trapping.
SPRG4-7 are readable from userspace. On booke, KVM will sync
these registers when it enters the guest, so that accesses from
guest userspace will work. The guest kernel, OTOH, must consistently
use either the real registers or the shared area between exits. This
also applies to the already-paravirted SPRG3.
On non-booke, it's not clear to what extent SPRG4-7 are supported
(they're not architected for book3s, but exist on at least some classic
chips). They are copied in the get/set regs ioctls, but I do not see any
non-booke emulation. I also do not see any syncing with real registers
(in PR-mode) including the user-readable SPRG3. This patch should not
make that situation any worse.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Also fix wrteei 1 paravirt to check for a pending interrupt.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
int_pending was only being lowered if a bit in pending_exceptions
was cleared during exception delivery -- but for interrupts, we clear
it during IACK/TSR emulation. This caused paravirt for enabling
MSR[EE] to be ineffective.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This prevents us from inappropriately blocking in a KVM_SET_REGS
ioctl -- the MSR[WE] will take effect when the guest is next entered.
It also causes SRR1[WE] to be set when we enter the guest's interrupt
handler, which is what e500 hardware is documented to do.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This function should be called with interrupts disabled, to avoid
a race where an exception is delivered after we check, but the
resched kick is received before we disable interrupts (and thus doesn't
actually trigger the exit code that would recheck exceptions).
booke already does this properly in the lightweight exit case, but
not on initial entry.
For now, move the call of prepare_to_enter into subarch-specific code so
that booke can do the right thing here. Ideally book3s would do the same
thing, but I'm having a hard time seeing where it does any interrupt
disabling of this sort (plus it has several additional call sites), so
I'm deferring the book3s fix to someone more familiar with that code.
book3s behavior should be unchanged by this patch.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This function also updates paravirt int_pending, so rename it
to be more obvious that this is a collection of checks run prior
to (re)entering a guest.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we check prior to returning from a lightweight exit,
but not prior to initial entry.
book3s already does a similar test.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
As per specification the decrementer interrupt not happen when DEC is written
with 0. Also when DEC is zero, no decrementer running. So we should not start
hrtimer for decrementer when DEC = 0.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvmppc_emulate_dec() uses dec_nsec of type unsigned long and does below calculation:
dec_nsec = vcpu->arch.dec;
dec_nsec *= 1000;
This will truncate if DEC value "vcpu->arch.dec" is greater than 0xffff_ffff/1000.
For example : For tb_ticks_per_usec = 4a, we can not set decrementer more than ~58ms.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Acked-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The current implementation of mtmsr and mtmsrd are racy in that it does:
* check (int_pending == 0)
---> host sets int_pending = 1 <---
* write shared page
* done
while instead we should check for int_pending after the shared page is written.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
With hugetlbfs support emerging on e500, we should also support KVM
backing its guest memory by it.
This patch adds support for hugetlbfs into the e500 shadow mmu code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The hardcoded behavior prevents proper SMP support.
user space shall specify the vcpu's PIR as the vcpu id.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
It should contain the way, not the absolute TLB0 index.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This implements a shared-memory API for giving host userspace access to
the guest's TLB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Split out the portions of tlbe_priv that should be associated with host
entries into tlbe_ref. Base victim selection on the number of hardware
entries, not guest entries.
For TLB1, where one guest entry can be mapped by multiple host entries,
we use the host tlbe_ref for tracking page references. For the guest
TLB0 entries, we still track it with gtlb_priv, to avoid having to
retranslate if the entry is evicted from the host TLB but not the
guest TLB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The only place it makes sense to call this function already needs
to have preemption disabled.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Delay allocation of the shadow pid until we're ready to disable
preemption and write the entry.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
On some cpus the overhead for virtualization instructions is in the same
range as a system call. Having to call multiple ioctls to get set registers
will make certain userspace handled exits more expensive than necessary.
Lets provide a section in kvm_run that works as a shared save area
for guest registers.
We also provide two 64bit flags fields (architecture specific), that will
specify
1. which parts of these fields are valid.
2. which registers were modified by userspace
Each bit for these flag fields will define a group of registers (like
general purpose) or a single register.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch exports the s390 SIE hardware control block to userspace
via the mapping of the vcpu file descriptor. In order to do so,
a new arch callback named kvm_arch_vcpu_fault is introduced for all
architectures. It allows to map architecture specific pages.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch introduces a new config option for user controlled kernel
virtual machines. It introduces a parameter to KVM_CREATE_VM that
allows to set bits that alter the capabilities of the newly created
virtual machine.
The parameter is passed to kvm_arch_init_vm for all architectures.
The only valid modifier bit for now is KVM_VM_S390_UCONTROL.
This requires CAP_SYS_ADMIN privileges and creates a user controlled
virtual machine on s390 architectures.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Create a distinction between scheduler related preempt_enable_no_resched()
calls and the nearly one hundred other places in the kernel that do not
want to reschedule, for one reason or another.
This distinction matters for -rt, where the scheduler and the non-scheduler
preempt models (and checks) are different. For upstream it's purely
documentational.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/n/tip-gs88fvx2mdv5psnzxnv575ke@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With bug.h currently living right in linux/kernel.h there
are files that use BUG_ON and friends but are not including
the header explicitly. Fix them up so we can remove the
presence in kernel.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The old pci_remove_bus_device actually did stop and remove.
Make the name reflect that to reduce confusion.
This patch is done by sed scripts and changes back some incorrect
__pci_remove_bus_device changes.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/powerpc/platforms/powernv/setup.c: included 'asm/xics.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/kvm/book3s_hv.c: included 'linux/sched.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After this, we can remove the legacy iSeries code more easily.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using a multi-ISU MPIC, we can interrupts up to
isu_size * MPIC_MAX_ISU, not just isu_size, so allocate
the right size reverse map.
Without this, the code will constantly fallback to
a linear search.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
