If a packet stream uses an UnsupportedVL (virtual lane), the send
engine will not send the packet, and it will not indicate that an
error has occurred. This will cause the packet stream to block.
HFI has 8 virtual lanes available for packet streams. Each lane can
be enabled or disabled using the UnsupportedVL mask. If a lane is
disabled, adding a packet to the send context must be disallowed.
The current mask for determining unsupported VLs defaults to 0 (allow
all). This is incorrect. Only the VLs that are defined should be
allowed.
Determine which VLs are disabled (mtu == 0), and set the appropriate
unsupported bit in the mask. The correct mask will allow the send
engine to error on the invalid VL, and error recovery will work
correctly.
Cc: <stable@vger.kernel.org> # 4.9.x+
Fixes: 7724105686 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The SL specified by a user needs to be a valid SL.
Add a range check to the user specified SL value which protects from
running off the end of the SL to SC table.
CC: stable@vger.kernel.org
Fixes: 7724105686 ("IB/hfi1: add driver files")
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Uverbs shouldn't enforce QP state in the command unless the user set the QP
state bit in the attribute mask.
In addition, only copy qp attr fields which have the corresponding bit set
in the attribute mask over to the internal attr structure.
Fixes: 88de869bbe ("RDMA/uverbs: Ensure validity of current QP state value")
Fixes: bc38a6abdd ("[PATCH] IB uverbs: core implementation")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When programming the inbound/outbound ATUs, we call usleep_range() after
each checking PCIE_ATU_ENABLE bit. Unfortunately, the ATU programming
can be executed in atomic context:
inbound ATU programming could be called through
pci_epc_write_header()
=>dw_pcie_ep_write_header()
=>dw_pcie_prog_inbound_atu()
outbound ATU programming could be called through
pci_bus_read_config_dword()
=>dw_pcie_rd_conf()
=>dw_pcie_prog_outbound_atu()
Fix this issue by calling mdelay() instead.
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Fixes: d8bbeb39fb ("PCI: designware: Wait for iATU enable")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
[lorenzo.pieralisi@arm.com: commit log update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Commit 92f9ccca4c ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver DT bindings") managed to add a MAINTAINERS entry where it does
not really belong (ie in the middle of a totally unrelated series of
entries and in the wrong alphabetical order).
Fix it.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
We met a kernel panic when enabling earlycon, which is due to the fixmap
address of earlycon is not statically setup.
Currently the static fixmap setup in head_64.S only covers 2M virtual
address space, while it actually could be in 4M space with different
kernel configurations, e.g. when VSYSCALL emulation is disabled.
So increase the static space to 4M for now by defining FIXMAP_PMD_NUM to 2,
and add a build time check to ensure that the fixmap is covered by the
initial static page tables.
Fixes: 1ad83c858c ("x86_64,vsyscall: Make vsyscall emulation configurable")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: kernel test robot <rong.a.chen@intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com> (Xen parts)
Cc: H Peter Anvin <hpa@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180920025828.23699-1-feng.tang@intel.com
9092c71bb7 ("mm: use sc->priority for slab shrink targets") changed the
way that the target slab pressure is calculated and made it
priority-based:
delta = freeable >> priority;
delta *= 4;
do_div(delta, shrinker->seeks);
The problem is that on a default priority (which is 12) no pressure is
applied at all, if the number of potentially reclaimable objects is less
than 4096 (1<<12).
This causes the last objects on slab caches of no longer used cgroups to
(almost) never get reclaimed. It's obviously a waste of memory.
It can be especially painful, if these stale objects are holding a
reference to a dying cgroup. Slab LRU lists are reparented on memcg
offlining, but corresponding objects are still holding a reference to the
dying cgroup. If we don't scan these objects, the dying cgroup can't go
away. Most likely, the parent cgroup hasn't any directly charged objects,
only remaining objects from dying children cgroups. So it can easily hold
a reference to hundreds of dying cgroups.
If there are no big spikes in memory pressure, and new memory cgroups are
created and destroyed periodically, this causes the number of dying
cgroups grow steadily, causing a slow-ish and hard-to-detect memory
"leak". It's not a real leak, as the memory can be eventually reclaimed,
but it could not happen in a real life at all. I've seen hosts with a
steadily climbing number of dying cgroups, which doesn't show any signs of
a decline in months, despite the host is loaded with a production
workload.
It is an obvious waste of memory, and to prevent it, let's apply a minimal
pressure even on small shrinker lists. E.g. if there are freeable
objects, let's scan at least min(freeable, scan_batch) objects.
This fix significantly improves a chance of a dying cgroup to be
reclaimed, and together with some previous patches stops the steady growth
of the dying cgroups number on some of our hosts.
Link: http://lkml.kernel.org/r/20180905230759.12236-1-guro@fb.com
Fixes: 9092c71bb7 ("mm: use sc->priority for slab shrink targets")
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Rik van Riel <riel@surriel.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'm' kcore_list item could point to kclist_head, and it is incorrect to
look at m->addr / m->size in this case.
There is no choice but to run through the list of entries for every
address if we did not find any entry in the previous iteration
Reset 'm' to NULL in that case at Omar Sandoval's suggestion.
[akpm@linux-foundation.org: add comment]
Link: http://lkml.kernel.org/r/1536100702-28706-1-git-send-email-asmadeus@codewreck.org
Fixes: bf991c2231 ("proc/kcore: optimize multiple page reads")
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Omar Sandoval <osandov@osandov.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: James Morse <james.morse@arm.com>
Cc: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the clone and fork syscalls return EAGAIN when the limit on the
number of pids /proc/sys/kernel/pid_max is exceeded.
Currently, when the pid_max limit is exceeded, the kernel will return
ENOSPC from the fork and clone syscalls. This is contrary to the
documented behaviour, which explicitly calls out the pid_max case as one
where EAGAIN should be returned. It also leads to really confusing error
messages in userspace programs which will complain about a lack of disk
space when they fail to create processes/threads for this reason.
This error is being returned because alloc_pid() uses the idr api to find
a new pid; when there are none available, idr_alloc_cyclic() returns
-ENOSPC, and this is being propagated back to userspace.
This behaviour has been broken before, and was explicitly fixed in
commit 35f71bc0a0 ("fork: report pid reservation failure properly"),
so I think -EAGAIN is definitely the right thing to return in this case.
The current behaviour change dates from commit 95846ecf9d ("pid:
replace pid bitmap implementation with IDR AIP") and was I believe
unintentional.
This patch has no impact on the case where allocating a pid fails because
the child reaper for the namespace is dead; that case will still return
-ENOMEM.
Link: http://lkml.kernel.org/r/20180903111016.46461-1-ktsanaktsidis@zendesk.com
Fixes: 95846ecf9d ("pid: replace pid bitmap implementation with IDR AIP")
Signed-off-by: KJ Tsanaktsidis <ktsanaktsidis@zendesk.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Gargi Sharma <gs051095@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave, Andy and Peter are de facto overseing the mm parts of X86. Add an
explicit maintainers entry.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reinette Chatre is doing great job on enabling pseudo-locking and other
features in RDT. Add her as co-maintainer for RDT.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/1537472228-221799-1-git-send-email-fenghua.yu@intel.com
This reverts commit 11a6fc3dc7.
UBIFS wants to assert that xattr operations are only issued on files
with positive link count. The said patch made this operations return
-ENOENT for unlinked files such that the asserts will no longer trigger.
This was wrong since xattr operations are perfectly fine on unlinked
files.
Instead the assertions need to be fixed/removed.
Cc: <stable@vger.kernel.org>
Fixes: 11a6fc3dc7 ("ubifs: xattr: Don't operate on deleted inodes")
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Richard Weinberger <richard@nod.at>
The following sequence triggers
ubifs_assert(c, c->lst.taken_empty_lebs > 0);
at the end of ubifs_remount_fs():
mount -t ubifs /dev/ubi0_0 /mnt
echo 1 > /sys/kernel/debug/ubifs/ubi0_0/ro_error
umount /mnt
mount -t ubifs -o ro /dev/ubix_y /mnt
mount -o remount,ro /mnt
The resulting
UBIFS assert failed in ubifs_remount_fs at 1878 (pid 161)
is a false positive. In the case above c->lst.taken_empty_lebs has
never been changed from its initial zero value. This will only happen
when the deferred recovery is done.
Fix this by doing the assertion only when recovery has been done
already.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
The requested device name can be NULL or an empty string.
Check for that and refuse to continue. UBIFS has to do this manually
since we cannot use mount_bdev(), which checks for this condition.
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Reported-by: syzbot+38bd0f7865e5c6379280@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
We'd better have that documented in the kerneldoc header, so that it's
exposed to the doc generated by Sphinx.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a description for spi_mem_op.data.nbytes to the kerneldoc header.
Fixes: c36ff266dc ("spi: Extend the core to ease integration of SPI memory controllers")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When processing pmtu update from an icmp packet, it calls .update_pmtu
with sk instead of skb in sctp_transport_update_pmtu.
However for sctp, the daddr in the transport might be different from
inet_sock->inet_daddr or sk->sk_v6_daddr, which is used to update or
create the route cache. The incorrect daddr will cause a different
route cache created for the path.
So before calling .update_pmtu, inet_sock->inet_daddr/sk->sk_v6_daddr
should be updated with the daddr in the transport, and update it back
after it's done.
The issue has existed since route exceptions introduction.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Reported-by: ian.periam@dialogic.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt offload code currently supports only 'push' and 'pop' operation: let
.ndo_setup_tc() return -EOPNOTSUPP if VLAN 'modify' action is configured.
Fixes: 2ae7408fed ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handlers of IOCTLs in kvm_arch_vcpu_ioctl() are expected to set
their return value in "r" local var and break out of switch block
when they encounter some error.
This is because vcpu_load() is called before the switch block which
have a proper cleanup of vcpu_put() afterwards.
However, KVM_{GET,SET}_NESTED_STATE IOCTLs handlers just return
immediately on error without performing above mentioned cleanup.
Thus, change these handlers to behave as expected.
Fixes: 8fcc4b5923 ("kvm: nVMX: Introduce KVM_CAP_NESTED_STATE")
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Patrick Colp <patrick.colp@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
dev_set_drvdata() needs to be called before device_register()
exposes device to userspace. Otherwise kernel crashes after it
gets null pointer from dev_get_drvdata() when userspace tries
to access sysfs entries.
[Removed backtrace for length -- broonie]
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Because CRAT_CU_FLAGS_IOMMU_PRESENT was not set in some BIOS crat, we
need to workaround this.
For future compatibility, we also overwrite the bit in capability according
to the value of needs_iommu_device.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CWSR fails on Raven if the control stack is MTYPE_UC, which is used
for regular GART mappings. As a workaround we map it using MTYPE_NC.
The MEC firmware expects the control stack at one page offset from the
start of the MQD so it is part of the MQD allocation on GFXv9. AMDGPU
added a memory allocation flag just for this purpose.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yong Zhao <yong.zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A wrong register bit was examinated for checking SDMA status so it reports
false failures. This typo only appears on gfx_v7. gfx_v8 checks the correct
bit.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some reason I thought GPIOLIB handles translation from GPIO ranges
to pinctrl pins but it turns out not to be the case. This means that
when GPIOs operations are performed for a pin controller having a custom
GPIO base such as Cannon Lake and Ice Lake incorrect pin number gets
used internally.
Fix this in the same way we did for lock/unlock IRQ operations and
translate the GPIO number to pin before using it.
Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Reported-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The final field of a floppy_struct is the field "name", which is a pointer
to a string in kernel memory. The kernel pointer should not be copied to
user memory. The FDGETPRM ioctl copies a floppy_struct to user memory,
including this "name" field. This pointer cannot be used by the user
and it will leak a kernel address to user-space, which will reveal the
location of kernel code and data and undermine KASLR protection.
Model this code after the compat ioctl which copies the returned data
to a previously cleared temporary structure on the stack (excluding the
name pointer) and copy out to userspace from there. As we already have
an inparam union with an appropriate member and that memory is already
cleared even for read only calls make use of that as a temporary store.
Based on an initial patch by Brian Belleville.
CVE-2018-7755
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Broke up long line.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The generic netlink family is only initialized during module init,
so it should be __ro_after_init like all other generic netlink
families.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC-aware mode was introduced to mlxsw in commit 7b81953066 ("mlxsw: spectrum:
Configure MC-aware mode on mlxsw ports") and fixed up later in commit
3a3539cd36 ("mlxsw: spectrum_buffers: Set up a dedicated pool for BUM
traffic"). As the final piece of puzzle, a firmware issue whereby a wrong
priority was assigned to BUM traffic was corrected in FW version 13.1703.4.
Therefore require this FW version in the driver.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hen we're comparing the hardware completion mask passed in from the
driver with the internal tag pending mask, we need to account for the
fact that the internal tag is different from the hardware tag. If not,
then we can end up either prematurely completing the internal tag (since
it's not set in the hw mask), or simply flag an error:
ata2: illegal qc_active transition (100000000->00000001)
If the internal tag is set, then swap that with the hardware tag in this
case before comparing with what the hardware reports.
Fixes: 28361c4036 ("libata: add extra internal command")
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201151
Cc: stable@vger.kernel.org
Reported-by: Paul Sbarra <sbarra.paul@gmail.com>
Tested-by: Paul Sbarra <sbarra.paul@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The naked attribute is supported by at least gcc >= 4.6 (for ARM,
which is the only current user), gcc >= 8 (for x86), clang >= 3.1
and icc >= 13. See https://godbolt.org/z/350Dyc
Therefore, move it out of compiler-gcc.h so that the definition
is shared by all compilers.
This also fixes Clang support for ARM32 --- 815f0ddb34
("include/linux/compiler*.h: make compiler-*.h mutually exclusive").
Fixes: 815f0ddb34 ("include/linux/compiler*.h: make compiler-*.h mutually exclusive")
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Eli Friedman <efriedma@codeaurora.org>
Cc: Christopher Li <sparse@chrisli.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Cc: Dominique Martinet <asmadeus@codewreck.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-sparse@vger.kernel.org
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9c695203a7 ("compiler-gcc.h: gcc-4.5 needs noclone
and noinline on __naked functions") added noinline and noclone
as a workaround for a gcc 4.5 bug, which was resolved in 4.6.0.
Since now the minimum gcc supported version is 4.6,
we can clean it up.
See https://gcc.gnu.org/bugzilla/show_bug.cgi?id=44290
and https://godbolt.org/z/h6NMIL
Fixes: 815f0ddb34 ("include/linux/compiler*.h: make compiler-*.h mutually exclusive")
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Eli Friedman <efriedma@codeaurora.org>
Cc: Christopher Li <sparse@chrisli.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Cc: Dominique Martinet <asmadeus@codewreck.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-sparse@vger.kernel.org
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2015 when irda was dropped from the driver imx1 was broken. This
change reintroduces the support for the third interrupt of the UART.
Fixes: afe9cbb1a6 ("serial: imx: drop support for IRDA")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scan_pkey_feature() uses of_property_read_u32_array() to read the
ibm,processor-storage-keys property and calls be32_to_cpu() on the
value it gets. The problem is that of_property_read_u32_array() already
returns the value converted to the CPU byte order.
The value of pkeys_total ends up more or less sane because there's a min()
call in pkey_initialize() which reduces pkeys_total to 32. So in practice
the kernel ignores the fact that the hypervisor reserved one key for
itself (the device tree advertises 31 keys in my test VM).
This is wrong, but the effect in practice is that when a process tries to
allocate the 32nd key, it gets an -EINVAL error instead of -ENOSPC which
would indicate that there aren't any keys available
Fixes: cf43d3b264 ("powerpc: Enable pkey subsystem")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Functions typec_mux_get() and typec_switch_get() already
make sure that the mux device reference count is
incremented, but the same must be done to the driver module
as well to prevent the drivers from being unloaded in the
middle of operation.
This fixes a potential "BUG: unable to handle kernel paging
request at ..." from happening.
Fixes: 93dd2112c7 ("usb: typec: mux: Get the mux identifier from function parameter")
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applying dynamic usbcore quirks in early booting when the slab is
not yet ready would cause kernel panic of null pointer dereference
because the quirk_count has been counted as 1 while the quirk_list
was failed to allocate.
i.e.,
[ 1.044970] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1.044995] IP: [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
[ 1.045016] PGD 0
[ 1.045026] Oops: 0000 [#1] PREEMPT SMP
[ 1.046986] gsmi: Log Shutdown Reason 0x03
[ 1.046995] Modules linked in:
[ 1.047008] CPU: 0 PID: 81 Comm: kworker/0:3 Not tainted 4.4.154 #28
[ 1.047016] Hardware name: Google Coral/Coral, BIOS Google_Coral.10068.27.0 12/04/2017
[ 1.047028] Workqueue: usb_hub_wq hub_event
[ 1.047037] task: ffff88017a321c80 task.stack: ffff88017a384000
[ 1.047044] RIP: 0010:[<ffffffffb0953ec7>] [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
To tackle this odd, let's balance the quirk_count to 0 when the kcalloc
call fails, and defer the quirk setting into a lower level callback
which ensures that the kernel memory management has been initialized.
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Harry Pan <harry.pan@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes potential "BUG: unable to handle kernel paging
request at ..." from happening.
Fixes: fde0aa6c17 ("usb: common: Small class for USB role switches")
Cc: <stable@vger.kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On little endian platforms, csum_ipv6_magic() keeps len and proto in
CPU byte order. This generates a bad results leading to ICMPv6 packets
from other hosts being dropped by powerpc64le platforms.
In order to fix this, len and proto should be converted to network
byte order ie bigendian byte order. However checksumming 0x12345678
and 0x56341278 provide the exact same result so it is enough to
rotate the sum of len and proto by 1 byte.
PPC32 only support bigendian so the fix is needed for PPC64 only
Fixes: e9c4943a10 ("powerpc: Implement csum_ipv6_magic in assembly")
Reported-by: Jianlin Shi <jishi@redhat.com>
Reported-by: Xin Long <lucien.xin@gmail.com>
Cc: <stable@vger.kernel.org> # 4.18+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
usb_find_alt_setting() takes a pointer to a struct usb_host_config as
an argument; it searches for an interface with specified interface and
alternate setting numbers in that config. However, it crashes if the
usb_host_config pointer argument is NULL.
Since this is a general-purpose routine, available for use in many
places, we want to to be more robust. This patch makes it return NULL
whenever the config argument is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+19c3aaef85a89d451eac@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzing project found a use-after-free bug in the USB
core. The bug was caused by usbfs not unbinding from an interface
when the USB device file was closed, which led another process to
attempt the unbind later on, after the private data structure had been
deallocated.
The reason usbfs did not unbind the interface at the appropriate time
was because it thought the interface had never been claimed in the
first place. This was caused by the fact that
usb_driver_claim_interface() does not clean up properly when
device_bind_driver() returns an error. Although the error code gets
passed back to the caller, the iface->dev.driver pointer remains set
and iface->condition remains equal to USB_INTERFACE_BOUND.
This patch adds proper error handling to usb_driver_claim_interface().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+f84aa7209ccec829536f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below. This patch removes the two LPM-related function calls from the
routine.
The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine. But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.
Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant. usbfs doesn't interact with LPM at all.
Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8306095fd2 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we filter flags before they reach the core we need to generate our
own warnings.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting a ZERO_PACKET or not is sensible only for output.
In the input direction the device decides.
Likewise accepting short packets makes sense only for input.
This allows operation with panic_on_warn without opening up
a local DOS.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+843efa30c8821bd69f53@syzkaller.appspotmail.com
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6e22e3af7b.
The bug the patch describes to, has been already fixed in commit
2df6948428 ("USB: cdc-wdm: don't enable interrupts in USB-giveback")
so need to this, revert it.
Fixes: 6e22e3af7b ("usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
