Maxim 1586 V3 gain can be configured by external resistors
(R24, R25) connected to the FB3 pin. To avoid accidental
overvoltage, it now requires this gain to be configured
explicitly.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On this board, the PXA272 CPU voltage VCC_CORE is provided
by a Maxim 1586 voltage regulator. Use the regulator
framework to provide VCC_CORE control. When cpufreq will be
updated to ask for vcc_core, this will optimize power
drained by the board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On this board, the PXA270 CPU voltage VCC_CORE is provided
by a Maxim 1587A voltage regulator configured to provide
1.55 V maximum voltage for 624 MHz operation.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
After commit 6b849bcff0 (ASoC: Convert PXA
AC97 driver to probe with the platform device) AC97 controller device
should be registered explicitly for both ASoC and generic AC97 drivers
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Register userspace-consumer devices to allow userspace control of
voltage regulators supplying GPS and GPRS modules
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
For suspend/resume to work, spitz needs pxa_pm_suspend/resume to be
called. Otherwise PSPR is not set properly, and system will die during
resume.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Replace calls to pxa_gpio_mode with respective gpio_request() /
gpio_direction_input(). In principle these calls can be dropped as
the only use of those GPIO are IRQs and IRQ code does setup GPIO
correctly.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
As pxa now is the only user of sharpsl_pm we can drop several startup
functions into generic code thus dropping several global functions.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
collie_pm was the only non-PXA user of sharpsl_pm. Now as it's gone we
can merge code into one single file to allow further cleanup.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
CM-X300 can be assembled with different NAND flashes from different
manufacturers. Adding their configuration to the kernel is impractical,
therefore we will use the default NAND controller settings set up by the
bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Setup gpio-keys for EzX phones
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add a call to pxa_set_ac97_info() to enable the audio support.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
csb726 used obsolete and not working out-of-tree driver smc911x.
Switch it to use new smsc911x driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add voltage regulation capability to pxa2xx cpufreq
driver. The cpufreq will ask for a "vcc_core" regulator to
the regulator framework.
If a regulator is found at probe time, it will be used with
values specified in PXA270 Electrical, Mechanical, and
Thermal Specifications.
If not, it will be assumed for now that frequency change
will work without voltage control. This assumes that the
IPL/SPL installs sane values to an existing voltage
regulator (ie. voltage high enough to support the full
range).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA processors have several low-power modes. Currently kernel supports
only one of these modes for PM_SUSPEND_MEM.
This patch adds ability to set desired suspend mode for PXA27x based
machines.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
As reported by Aric Blumer, the pxa27x_udc driver does work
with pxa3xx devices. Add support into device files.
Reported-by: Aric Blumer <aric@sdgsystems.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Matt Reimer <mattjreimer@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The default value is 16 IRQs. Zylonite needs 32, ASIC3 based boards need 70.
My problem is still that due to the way IRQ_GPIO is hardcoded, ASIC3 based boards
need 70 IRQs starting at IRQ_BOARD_START. If I define ASIC3 IRQs similar to LoCoMo
or SA1111, things break as soon as something selects PXA_HAVE_BOARD_IRQS.
Increasing the default number of board IRQs to 70 instead doesn't seem very nice.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The PXA_PWM config option is really redundant since the introduction
of HAVE_PWM, replace that with HAVE_PWM to avoid confusion.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PWMs on PXA168/910 start at number 1 instead of 0, (i.e. PWM1/2/3/4 instead
of PWM0/1/2/3 on PXA25x/PXA27x/PXA3xx). Allow this number to be specified
in pwm_id_table.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
